USER MANUAL
Contents
1. 5 Remove the three base screws from the underside of the Power Tower and open the base cover saving the screws Slide out the blank panel and any modules panels Connect the TA 110HD see section 6 and then slide the TA 110HD into place Replace the other modules panels and the blank panel Replace the base cover and fasten the three base screws back in place 6 Using the XGA Line Transmitter s Receiver You can use the TA 110HD XGA Line Transmitter and the TP 120 XGA Line Receiver to configure an XGA to Twisted Pair Transmitter and Receiver system To connect the TA 110HD XGA Line Transmitter with the TP 120 XGA Line Receiver as the example in Figure 2 illustrates do the following 1 On the TA 110HD connect the XGA source for example the HD 15 output from a computer s graphics card to the XGA IN HDI5F connector On the TP 120 connect the XGA OUT HDISF connector to the XGA acceptor for example a monitor Connect the LINE OUT RJ 45 connector on the TA 110HD to the LINE IN RJ 45 connector on the TP 120 via UTP cabling transmission can exceed 300ft 2100m On both the TA 110HD and the TP 120 connect the 12V DC power adapter to the power socket and connect the adapter to the mains electricity The signal from the XGA source is transmitted via CAT 5 cable decoded and converted at the XGA OUT HDISF connector to the XGA acceptor On the TP 120 adjust the output signal level and or cable compensation eq2. Technical Specifications Technical Specifications Table 3 includes the technical specifications Table 3 Technical Specifications of the TA 110HD INPUT 1 VGA UXGA on an HD15 connector OUTPUT 1 RJ 45 LINE OUTPUT connector RESOLUTION Up to UXGA DIFF GAIN 2 996 DIFF PHASE 0 3 Deg K FACTOR lt 0 05 S N RATIO 69dB COUPLING AC POWER SOURCE 12 VDC 60mA DIMENSIONS 5 67cm x 5 0cm x 4 3cm 2 23 x 1 97 x 1 7 W D H WEIGHT 0 14 kg 0 31 Ibs approx ACCESSORIES Power supply 1 Specifications are subject to change without notice 2 For the Transmitter Receiver pair LIMITED WARRANTY Kramer Electronics hereafter Kramer warrants this product free from defects in material and workmanship under the following terms HOW LONGIS THE WARRANTY Labor and parts are warranted for seven years from the date of the first customer purchase WHOIS PROTECTED Only the first purchase customer may enforce this warranty WHATIS COVERED AND WHATISNOT COVERED Except as below this warranty covers all defects in material or workmanship in this product The following are not covered by the warranty 1 Any product which is not distributed by Kramer or which is not purchased from an authorized Kramer dealer If you are uncertain as to whether a dealer is authorized please contact Kramer at one of the agents listed in the Web site www kramerelectronics com 2 An
3. s 3 For the name of the nearest Kramer authorized service center consult your authorized dealer LIMITATION OF IMPLIED WARRANTIES All implied warranties including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty EXCLUSION OF DAMAGES The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option Kramer shall not be liable for 1 Damage to other property caused by defects in this product damages based upon inconvenience loss of use of the product loss of time commercial loss or 2 Any other damages whether incidental consequential or otherwise Some countries may not allow limitations on how long an implied warranty lasts and or do not allow the exclusion or limitation of incidental or consequential damages so the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from place to place NOTE All products returned to Kramer for service must have prior approval This may be obtained from your dealer This equipment has been tested to determine compliance with the requirements of EN 50081 Electromagnetic compatibility EMC generic emission standard Part 1 Residential commercial and lightindustry EN 50082 Electromagnetic compatibility EMC generic immunity standard Part 1 Residential co
4. 251 Your TA 110HD XGA Line Transmitter 4 Your TA 110HD XGA Line Transmitter Figure 1 and Table 1 define the TA 110HD Front Panel Rear Panel LINE OuT TA 110HD Figure 1 TA 110HD XGA Line Transmitter Front and Rear Panels Table 1 TA 110HD XGA Line Transmitter Features Feature Function 1 XGA IN HD15F Connector Connect to the XGA source 2 Side Rails For sliding onto the rails of the Power Tower Plus 3 HS Switch Slide the switch to the left to change the HS polarity to NEG negative polarity slide the switch to the right NORM to retain the polarity 4 VS Switch Slide the switch to the left to change the VS polarity to NEG negative polarity slide the switch to the right NORM to retain the polarity 5 ONLED llluminates when receiving power 6 LINE OUTPUT RJ 45 Connects to the LINE IN RJ 45 connector on a transmitter for Connector example the PT 120 or TP 120 XGA Line Receiver 7 DC 12V PIN Connects to the connector for powering the unit GND PIN Connects to the Ground 1 Horizontal Sync 2 By default both switches are set to the right 3 Downgoing syncs 4 Vertical Sync 5 Using a UTP cable with CAT 5 connectors at both ends the PINOUT is defined in Table 2 and Figure 3 4 KRAMER SIMPLE CREATIVE TECHNOLOGY Mounting the TA 110HD 5 Mounting the TA 110HD To mount the TA 110HD in the Power Tower do the following 1 4
5. Kramer Electronics Ltd l KRAMER USER MANUAL Model TA 110HD XGA Line Transmitter Contents Contents 1 Introduction 2 Getting Started 3 Overview 3 1 About the Power Connect Feature 3 2 Shielded Twisted Pair STP Unshielded Twisted Pair UTP 3 3 TA 110HD XGA Line Transmitter 3 4 Achieving the Best Performance 4 Your TA 110HD XGA Line Transmitter 5 Mounting the TA 110HD 6 Using the XGA Line Transmitter s Receiver 6 1 Wiring the CAT 5 LINE IN LINE OUT RJ 45 Connectors 7 Technical Specifications Figures Figure 1 TA 110HD XGA Line Transmitter Front and Rear Panels Figure 2 XGA to Twisted Pair Transmitter and Receiver System via UTP Cable Figure 3 CAT 5 PINOUT Tables Table 1 TA 110HD XGA Line Transmitter Features Table 2 CAT 5 PINOUT Table 3 Technical Specifications of the TA 110HD NAW Ui d C202 R2 b2 E E E OR OR Introduction 1 Introduction Welcome to Kramer Electronics since 1981 a world of unique creative and affordable solutions to the infinite range of problems that confront the video audio and presentation professional on a daily basis In recent years we have redesigned and upgraded most of our line making the best even better Our 500 plus different models now appear in 8 Groups which are clearly defined by function Congratulations on purchasing your Kramer TA 110HD XGA Line Transmitter which is ideal for e Presentation and multimedia appli
6. cations e Longrange graphics distribution for schools hospitals security and stores The package includes the following items e TA 110HD XGA Line Transmitter e Power adapter 12V DC Input and this user manual 2 Getting Started We recommend that you e Unpack the equipment carefully and save the original box and packaging materials for possible future shipment e Review the contents of this user manual e Use Kramer high performance high resolution cables 3 Overview This section describes e The power connect feature see section 3 1 e Using shielded twisted pair STP unshielded twisted pair UTP see section 3 2 e Asummary of the TA 110HD XGA Line Transmitter see section 3 3 e Recommendations for achieving the best performance see section 3 4 1 GROUP 1 Distribution Amplifiers GROUP 2 Video and Audio Switchers Matrix Switchers and Controllers GROUP 3 Video Audio VGA XGA Processors GROUP 4 Interfaces and Sync Processors GROUP 5 Twisted Pair Interfaces GROUP 6 Accessories and Rack Adapters GROUP 7 Scan Converters and Scalers and GROUP 8 Cables and Connectors 2 Download up to date Kramer user manuals from the Internet at this URL http www kramerelectronics com 3 The complete list of Kramer cables is on our Web site at http www kramerelectronics com 1 Overview 3 1 About the Power Connect Feature The Power Connect feature applies as long as the cable can carry power The distance doe
7. mmercial and light industry environment CFR 47 FCC Rules and Regulations Part 15 Radio frequency devices Subpart B Unintentional radiators CAUTION Servicing the machines can only be done by an authorized Kramer technician Any user who makes changes or modifications to the unit without the expressed approval of the manufacturer will void user authority to operate the equipment EO Use the supplied DC power supply to feed power to the machine po Please use recommended interconnection cables to connect the machine to other components 8 KRAMER SIMPLE CREATIVE TECHNOLOGY For the latest information on our products and a list of Kramer distributors visit our Web site www kramerelectronics com where updates to this user manual may be found We welcome your questions comments and feedback Safety Warning Disconnect the unit from the power supply before opening servicing Caution 9001 o 32 QS ia Institute of Quality amp Control Kramer Electronics Ltd Web site www kramerelectronics com E mail info kramerel com P N 2900 000272 REV 1
8. s not exceed 50 meters on standard CATS cable for longer distances heavy gauge cable should be used For a CATS cable exceeding a distance of 50 meters separate power supplies should be connected to the transmitter and to the receiver simultaneously 3 2 Shielded Twisted Pair STP Unshielded Twisted Pair UTP The decision whether to use shielded twisted pair STP cable or unshielded twisted pair UTP cable depends on the nature of the application It is recommended that in applications with high interference shielded twisted pair STP cable is used However the shield itself does create a capacitance that degrades the frequency response of the machines For shorter distances of 50m or so shielded twisted pair STP cable is preferred because it provides protection from interference degradation is not apparent For a long range applications unshielded twisted pair UTP cable is preferred However the unshielded twisted pair UTP cable should be installed far away from electric cables motors and so on which are prone to create electrical interference 1 CATS cable is still suitable for the video audio transmission but not for feeding the power at these distances 2 KRAMER SIMPLE CREATIVE TECHNOLOGY Overview 3 3 TA 110HD XGA Line Transmitter The TA 110HD is a modular unit that can be mounted inside the Power Tower by sliding the unit onto the rails on the connection panel Using a XGA Line Transmi
9. tter the TA 110HD with a receiver for example the PT 120 or TP 120 constitutes a VGA XGA to Twisted Pair Transmitter and Receiver The Kramer TA 110HD is an XGA line transmitter that receives an XGA signal and transmits it over a CAT 5 cable to the PT 120 or TP 120 receiver In particular the TA 110HD Has a resolution of up to UXGA Can use the simplest UTP CAT 5 cables and performs even better with higher quality cables Has the power connect feature Is 12VDC fed 3 4 Achieving the Best Performance Achieving the best performance means Connecting only good quality connection cables thus avoiding interference deterioration in signal quality due to poor matching and elevated noise levels often associated with low quality cables Avoiding interference from neighboring electrical appliances and positioning your XGA Line Transmitter s Receiver away from moisture excessive sunlight and dust No operator serviceable parts inside unit Use only the Kramer Electronics input power wall adapter that is provided with this unit Eventi Disconnect power and unplug unit from wall before installing or removing device or servicing unit 1 The TA 110HD is also available for use with the Kramer TBUS 2 2 Powering via the CATS cable from either the receiver or the transmitter is good for 50 meters Above it both sides should be fed with power 3 For example model number AD2512C part number 2535 000
10. ualization level if required If necessary set the HS and VS switches on the units 1 For distances of up to 50 meters you can connect a power adapter to either the TA 110HD or TP 120 Above it both sides should be fed with power 2 Use a screwdriver to carefully rotate the trimmer adjusting the appropriate level 3 By default both switches are set for normal H SYNC and V SYNC polarity Using the XGA Line Transmitter s Receiver Up to gt 300ft gt 100m UTP Cable XGA Acceptor XGA Source LINE IN XGA Line Receiver KRAMER TA 110HD LINE OUT on rear panel Figure 2 XGA to Twisted Pair Transmitter and Receiver System via UTP Cable 6 1 Wiring the CAT 5 LINE IN LINE OUT RJ 45 Connectors Table 2 and Figure 3 define the CAT 5 PINOUT using a straight pin to pin cable with RJ 45 connectors Figure 3 CAT 5 PINOUT Table 2 CAT 5 PINOUT EIA TIA 568A EIA TIA 568B PIN Wire Color PIN Wire Color 1 Green White 1 Orange White 2 Green 2 Orange 3 Orange White 3 Green White 4 Blue 4 Blue 5 Blue White 5 Blue White 6 Orange 6 Green 7 Brown White 7 Brown White 8 Brown 8 Brown S Pair 1 4and5 Pair 1 4and5 Pair2 3and6 Pair 2 1and2 Pair3 1and2 Pair3 3and6 Pair4 7and8 Pair 4 7 and 8 12 45 78 36 6 KRAMER SIMPLE CREATIVE TECHNOLOGY
11. y product on which the serial number has been defaced modified or removed 3 Damage deterioration or malfunction resulting from i Accident misuse abuse neglect fire water lightning orother acts of nature ii Product modification or failure to follow instructions supplied with the product iii Repairorattempted repair by anyone not authorized by Kramer iv Any shipment ofthe product claims must be presented to the carrier v Removalorinstallation ofthe product vi Anyothercause which does not relate to a product defect vii Cartons equipment enclosures cables or accessories used in conjunction with the product WHAT WE WILL PAY FOR AND WHAT WE WILLNOT PAY FOR We will pay labor and material expenses for covered items We will not pay for the following 1 Removal or installations charges 2 Costs of initial technical adjustments set up including adjustment of user controls or programming These costs are the responsibility of the Kramer dealer from whom the product was purchased 3 Shipping charges HOW YOU CAN GET WARRANTY SERVICE l To obtain service on you product you must take or ship it prepaid to any authorized Kramer service center 2 Whenever warranty service is required the original dated invoice or a copy must be presented as proof of warranty coverage and should be included in any shipment of the product Please also include in any mailing a contact name company address and a description of the problem
Download Pdf Manuals
Related Search