GPS Vehicle tracker - Armazém do Rastreador
Contents
1. Conceox Track amp Achieve Powered by Concox GPS Vehicle tracker GPS GSM SMS GPRS Powered by Concox User Manual Version 4 1N This user manual has been specially designed to guide you through the functions and features of your GPS vehicle tracker Concex Track amp Achieve 1 Accessories Device Power cord Microphone vvvvyv User Manual 2 Specifications CRX Powered by Concox SOS alarm cable amp button Dimension 106 L x 54 W x 16 H mm Weight 96g Backup Battery 450mAh 3 7V Operation Temperature youre Humidity 5 95 Standby Time 160 hours GSM Frequencies 850 900 1800 1900 MHz GPRS Class 12 GPS Channel 20 GPS Sensitivity 159dBm Acquisition Sensitivity 144dBm Position Accuracy 10m TTFF Open Sky Cold Start lt 38s Warm Start lt 15s Hot Start lt 2s GSM GPS Antenna Built in design LED Indicator GSM green GPS blue Power red Data Transmit TCP SMS Geo fence View any existing Geo fence in the map Speeding Alarm Report when speeds higher than the pre set value Low Power Alarm Alarm when backup battery is running out Non movement Detection Movement alarm based on built in 3D motion sensor Mileage Report Track by time distance interval Remote Control Cut off petrol electricity Concex CRX Track amp Achieve Powered by Concox 32. Firstly you should set a center number Please refer to 6 6 Only center number can send the command to the device to cut off and restore oil The format is RELAY 1 After the command is carried out it will reply Cut off the fuel supply Success Speed 0 Km h If the command didn t carry out it will reply the reason about Concex CRX Track amp Achieve Powered by Concox fail to carry out Note To ensure the safety of the driver and the car this command is valid only under two conditions the GPS is located the speed is less than 20km h 6 8 Restoring Oil 1 Via platform When the alarm is off sending recover oil commands manually Device will restore oil supplying and vehicle will work normally again Platform account password is needed when sending oil cut off command 2 Via SMS Only center number can send the command to the device to restore oil The format is RELAY 0 After the command is carried out it will receive Restore fuel supply Success 6 9 Over speed Alarm When the car is moving over a limited speed in average in a limited time period then the device will send over speed alarm SMS to user To turn on the over speed function please send below SMS command SPEED Time Limited speed Time range Second 5 600s default as 20s Limited speed range km h 0 255 0 refers to turn off over speed alarm function Example SPEED 3 120 Means when the car is moving over 120km h in average in
3. 3 minutes the device will send over speed alarm to user 7 Web based tracking online activation The GPRS web based tracking platform allows real time tracking with the latest Google maps There is also a playback feature that allows you to view where the vehicle has been for up to 30 days in the past making it ideal for fleet management 8 Trouble shooting If you are having trouble with your device try these troubleshooting procedures before contacting a service professional Concex CRX Track amp Achieve Powered by Concox Problems Causes Solutions Fail to connect The fuse blows Replace the fuse platform ACC ignition disconnected Turn on ACC with key Fail to connect network Wrong installation of SIM card Check SIM card installation Refer to 4 1 Install SIM card Filth on the SIM card iron surface Clean it Useless SIM Contact internet service provider Improper installation Check installation of device Refer to 4 2 Install the device Beyond GSM service area Use it in effective GSM service offer area Bad signal Try again in a better signal area Fail to charge The voltage is unsuitable Connect with power with suitable voltage Improper connection Check connection with charger Concex CRX Track amp Achieve Powered by Concox Warranty instructions and service 1 The warranty is valid only when the warranty card i
4. LED Indications Tele cutoff Power interface Petrolelectricity acc interface nterface Tae a a Power on off SIM card slot Data interface z MIC intertace SOS interface i __ I oo GPS LED iidioator GSM LED indicator Power status GPS LED Indicator Blue Flashing interval 0 1s Searching GPS signal Solid blue GPS fix OFF No GPS fix or initializing GSM LED Indicator Green Quick flashing interval 0 1s GSM initializing Slow flashing flash 0 1s every 2s Receive GSM signal normally Solid green Connected to GSM network OFF No GSM signal Power Status Red Flashing interval 0 1s Low battery Slow flashing interval 0 2s Full charge Slow flashing flash 0 1s every 2s Normal operating Solid Red Charging OFF Low battery Power off Ignition detection indication three LED indicators take turns flashing Concex CRX Track amp Achieve Powered by Concox 4 Getting Started Please follow below instructions for ensuring safe and correct use 4 1 Install the SIM card Place the SIM card into the device with the gold colored side facing down Note Make sure there is enough credit on the SIM card If you will be using the GPRS function you should pay attention to the current SIM card GPRS charge 4 2 Install the device You need to choose somewhere that it won t be found because the whole point of fitti
5. WHERE to the SIM number of device The device will send a location message automatically You can get the coordinates If the device does not search any information of location it will send No data to the cell phone Example Lat N22 571285 Lon E113 877115 Course 42 20 Speed 0 0740 DateTime 10 11 23 22 28 51 1 2 SMS URL to the SIM number of device The device will send a location Google Map link If the device does not search any information of location it will send No data to the cell phone Example lt Date Time 10 11 23 23 42 51 gt http maps google com maps q N22 571490 E113 877103 2 Via platform Go to the platform website offered by dealers to check your vehicle location 6 3 SOS alarm In emergent case press SOS for 3s to activate SOS alarm Then the device will send SOS SMS to preset specific numbers and then dial the numbers in circles until the call is picked up At the meantime the device will upload SOS alarm data to the server And it will send SOS Alarm lt DateTime 11 06 17 14 53 O6 gt http maps google com maps q N22576713 E113 916585 Note The specific numbers should be preset just refer to 6 4 6 4 Wire cut off alarm Concex CRX Track amp Achieve Powered by Concox When the electricity supply of device is cut off it will activate cut off alarm In this case the device will send related SMS to the specific numbers and dial the numbers in circles If nobody answers t
6. pin Firmware updating interface expanded function to reserve space 5 MIC line 2 pin Externally connect to microphone for voice monitoring function 6 SOS line 2 pin Externally connect to SOS switch for SOS function 5 Quick Operation Instructions Operation Tips To properly use the device common parameters should be set before initial use This can be done by using the parameter editor or by sending SMS commands to the device should be English comma and no space before and after the comma 5 1 APN setting To connect default platform http www gpsyeah com please send the SMS command below APN command format APN APN s Name E g APN internet internet is the APN of carrier The device will reply OK if setting successfully Note The APN of some countries have user name and password you may need to send SMS command as following APN APN name user name password E g APN internet CLIENTE AMENA 5 2 DNS setting To connect other platform please send the two SMS commands bleow Command format APN APN s Name SERVER 1 DNS Port 0 E g Concex CRX Track amp Achieve Powered by Concox APN internet SERVER 1 www cooaccess net 8841 0 It will reply OK after set successfully 5 3 ON OFF GPRS When you want to disable GPRS you can SMS command to the SIM card number which used in the device Command format GPRS ON GPRSON 1 GPRS OFF GPRSON O It will reply OK a
7. restoring oil command Sensoralm 10 3 1 180 detect 3 vibrations in 10s the alarm delay is 180s Defense time 10 the defense delay is 10 minute TimeZone E 8 0 set time zone default as E8 The replied information contains IMEI number GPRS Interval SENDS SOS center number sensor time interval defense time and time zone 5 9 Check GPRS parameters Concex CRX Track amp Achieve Powered by Concox SMS command format GPRSSET Eg GPRSSET Reply message GPRS ON GPRS on off status APN CMNET 0 0 0 0 0 APN setting information Server 1 egt06 szdatasource com 8841 0 platform information URL http maps google com maps q preset web link setting information 5 10 GPRS time interval The default GPRS time sending interval is 10s which means the device will upload positioning data to the platform server every 10s Users can modify GPRS time sending interval by SMS TIMER time second The time ranges from 10 18000s For example TIMER 10 It means the device will upload data to the server every 10s 5 11 Sensor alarm time setting When the vehicle power is off and ACC is in low level if ACC is off over 10 minutes the device will enter sensor alarm state In this case if the vehicle vibrates for a few times it will activate the vibration alarm system If the vehicle battery is still not on ACC is in low level after 3 minutes the device will start vibration alarm SMS format DE
8. FENSE TIME minutes The time ranges from 1 to 60 mins For example DEFENSE 15 It means when ACC is in low level for 15mins it will enter sensor alarm status vehicle power is off NOTE 1 Preset SOS numbers when send SMS alarm messages and calls 2 If there is no need for vibration alarm please SMS SENSOR O to close it 5 12 Restore to factory setting SMS command format FACTORY to set all parameter to default factory value Once received OK it succeeds 5 13 Reboot device When there is something wrong with the link of GPRS e g The parameter setting of the device is correct but you can t track the car on the platform At this moment you can send a command to the device to reboot the device The format is RESET After receiving this command the device will reboot after 1mins Concex CRX Track amp Achieve Powered by Concox 6 Operation of device 6 1 Power on Power off Power on Once insert a valid SIM card and connect all the wires turn on the device then Power LED will flash first During signal searching process GSM and GPS LED will flash Once GPS LED keeps solid light it means the device has been located and it starts to work Power off Just turn off the power switch The device will begin to upload positioning data to server once inserting a valid SIM card and power on During the working time it can upload data to server every 10 seconds 6 2 Check location 1 Via SMS 1 1 SMS
9. fter set successfully 5 4 Add specific number SMS command to the device to set the SOS number SOS A No 1 No 2 No 3 A means to add new numbers for example SOS A 13510905991 13510905992 13510905993 If there is only one SOS number you can appoint a specific number as SOS number And the null means no adding For example SOS A 13510905991 means to set the first number as SOS number SOS A 13510905992 means to set the second number as SOS number SOS A 13510905993 means to set the third number as SOS number If set successfully there is a success reply SMS 5 5 Delete specific number Before deleting specific number please check its corresponding code For the code please SMS PARAM to the device SMS command to the device to delete the number SOS D serial NO 1 serial NO 2 serial NO 3 D means to delete the number for example SOS D 1 means to delete the first number SOS D 3 means to delete the third number If you want to delete more than one numbers you can send this command SOS D 1 3 means to delete the first and third numbers If you forget serial number of the mobile number you want delete you can send this command SOS D mobile number means to delete the mobile number directly For example SOS D 13527852360 means to delete the 13527852360 directly After deleting the SOS number it will receive Delete number 135XXXXXXXX success specific number total 2 for successful deleting of the
10. he call just keeps 3 loops at most At the meantime the device will upload SOS alarm data to the server And it will send Cut Power lt Date Time 11 06 17 14 53 06 gt http maps google com maps q N22576713 E113 916585 Note The specific numbers should be preset just refer to 6 4 6 5 Low battery alarm When the device is only working with battery once the internal voltage of battery is less than 3 7V device will send low battery alarm sms to specific number and alarm on platform Low battery alarm sms content example Attention battery too low please charge Which means the battery is to low to inform user charging it in time Note The specific numbers should be preset just refer to 6 4 6 6 Voice monitoring When the special number cell phone dial device ringing for 10 seconds it will enter voice monitoring status At this time caller can monitoring the sound in vehicle Incoming call from non special number will not activate voice monitoring function Note To realize this function please set special number beforehand The SIM card put into the device should be equipped with caller identification 6 7 Oil cut off 1 Via platform Send oil cut off command on platform To make sure the security of vehicle tracker can only indicate to cut off oil when GPS is in valid position status and the speed is less than 20KM H or in static Platform account password is needed when sending oil cut off command 2 Via SMS
11. ng covert GPS vehicle tracker is the secrecy element Installation please refers to below picture NOTE 1 Any high power devices such as reversing radar anti theft device or communication equipment would affect the signal of the device 2 All metallic cases of the windshield will attenuate the signal on the tracking device It s simply due to the shielding effects of the metal compound of the case Under rear windshield Concex CRX Track amp Achieve Powered by Concox 4 3 Wiring configuration ai _ 1 Keypod 2 Keypod I 3 MIC l 4 MIC I 5 TX l 6 RX l 7 GND 3 MOTOR g9 ACC 10 11 i 1 wa T a 1 TT Line No Specification Color Instruction 1 2 Keypod Orange Orange Connect to SOS button 3 4 MIC MIC Black Red Connect to Microphone 5 TX Green Sending data TX backup 6 RX White Receiving data RX backup 7 GND Black Ground wire 8 MOTOR Yellow Connect to relay control line 9 ACC White Connect to ACC ignition 10 V Black thick Negative side of 12V 24V 11 V Red thick car storage battery Notes of the relay wiring The relay wiring of pump oil connectors of both ends are a fine white line 85 and a fine yellow line 86 The fine white line 85 is connected to vehicle positive power 12V The fine yellow line is connected to the device relay control line Cut off the posi
12. s properly completed and upon presentation of the proof of purchase consisting of original invoice indicating the date of purchase model and serial No of the product We reserve the right to refuse warranty if this information has been removed or changed after the original purchase of the product from the dealer 2 Our obligations are limited to repair of the defect or replacement the defective part or at its discretion replacement of the product itself 3 Warranty repairs must be carried out by our Authorized Service Centre Warranty cover will be void even if a repair has been attempted by any unauthorized service centre 4 Repair or replacement under the terms of this warranty does not provide right to extension or renewal of the warranty period 5 The warranty is not applicable to cases other than defects in material design and workmanship Maintenance Record Date Serviced by Product Model IMEI Number Fault Descriptions Comments ShenZhen Concox Information Technology CO Ltd Tel 595981970735 E mail comercial concox com br Add 4 F Building B Gaoxinqi Industrial Park Liuxian 1st Road No 67 Bao an District Shenzhen www concox com br
13. specific Concex CRX Track amp Achieve Powered by Concox number 5 6 Set the center number If you want to cut off restore oil by SMS command you have to set a center number firstly Only the center number can send the cut off restore oil command to the device You can set your own mobile number as center number The command for setting center number is CENTER A mobile number For example CENTER A 15942703401 If set successfully there is an OK reply message NOTE Only the SOS number can be used to set center number successfully 5 7 Delete the center number SMS command to the device to delete the center number The command is CENTER D For example CENTER D If set successfully there is an OK reply SMS NOTE Only the SOS number can be used to delete center number successfully Only SOS phone number can send this command successfully to set the center number There is only one center number can be set 5 8 Check parameter setting Send command to the terminal you can check the parameter setting Command format PARAM e g PARAM Information replied IMEI 35341 9032348877 IMEI number of the device GPRS Interval 10 10 GPS data uploading Interval SENDS 5 the GPS working time when ACC is OFF SOS 15942703401 SOS numbers maximum 3 SOS numbers can be set and used for alarm and monitoring Center Number 15942703401 only 1 center number can be set and used for cutting off
14. tive connection line of the pump then connect in series to the relay N C contact thick green line 87a and the other end to relay COM contact thick green line 30 Concox CRX Track amp Achieve Powered by Concox 4 4 Device wiring diagram K UV J E Connect to SOS button R9232 ij 8 l 2A FUSE Opo Red Vw Y T a OT Connect to microphone eas Yellow Orange oo Storage 12 24V battery ACC ON Relay p 12V or 24V 85 30 87a 86 OFF START Ignition key Pump Please choose the right relay 12V standard 24V optional for the proper installation 4 5 Power ACC Tele cutoff petrol electricity control line 4 pin 1 Your device comes with a power cord and is designed to use only manufacturer specified original device The red line is positive while the black one is negative the side should not be connect with ground wire 2 The ACC line white connects to ACC switch of the vehicle Please be sure Concex CRX Track amp Achieve Powered by Concox to connect the ACC line otherwise the device will enter ignition detection status when disconnect the ACC line If you don t need to anti theft temporarily just connect the ACC line to the positive side in parallel 3 Tele cutoff petrol electricity control line yellow is connected to pin 86 of the Tele cutoff petrol electricity relay equal to the yellow line of the relay socket 4 USB cable 3
Download Pdf Manuals
Related Search