Home

PF100

1. Both sides Mounting Knob aU While holding the appliance down with one hand lift the door gently from the bottom with the other hand and remove the door attachment protrusions top first and then bottom 5 Remove the top plate and the folding plate then fold the folding plate TL OO m a j a i A CLT ATMO 14 In the event of failure Please check the following before requesting repair Problem Things to check for No display appears even Is the power cord securely plugged in after switch is turned on gt Please plug in securely or insert the plug into another outlet Is the power switch turned on gt Please make sure it is on Temperature does not rise Check to see if the setting temperature is not below room temperature gt Please use a temperature setting higher than room temperature Temperature does not fall Check that the temperature setting is not below room temperature gt Since this product does not have the ability to cool itself it can be set at a temperature below room temperature Please use above room
2. 8 4 Mount and attach the top plate by lightly tapping by hand from the top ZX I Front is written on the inside of the top plate Please place it properly 5 Attach door while holding up the folding plate Hold the door with both hands after you have fitted the protrusion at the top of the door into the hole into the top plate while lifting the top plate lightly in the direction of the arrow and attach the lower protrusion of the door to the heater 6 Firmly attach the door to the heater and folding plate with the mounting knob Both sides a Completed product Place on horizontal surface at proper distance from walls and other objects The front of the appliance should be kept clear Please leave a space of more than 4 5 cm from 4 5cm back and sides Please make sure that the table on which the Fermenter is placed is secure Cl O z Shelf plate 0 0 0 T H Convection board O 0 Shelf plate J E Shelves can be added as purchase options 9 Placing the humidification dish FIII dish with small amount of cold or lukewarm water and place in the center of the hot plate If used for a long time add more water to the humidificatio
3. KNEADER Fermenter Part number PF 100 Owner s Manual General household articles Not for commercial use Thank you for purchasing the Kneader Fermenter PF 102 Please keep this manual so that you can refer to it in the future Before using this appliance be sure to read all the instructions This appliance was designed for use in Japan only and should not be used in other countries Table of contents Safety concerns Please observe i 2 Meanings of symbols Warnings Cautionary measures Tank usage Features of the Fermenter PF1 00 a ET E E ENE AEAT 5 Names of parts aed ates cca EIEEE AEE E A EA ES A 6 Main parts How to use EPPA AN EE ws pica ter E ATI EEA EE EAA E T E 7 Preliminary preparation of Fermenter Using the Fermenter Maintenance nsss 13 Main body parts Disassembly and storage In case of malfunction PE ESTEN EEA T 16 After sales SOA COS seeker cies 17 Specifications a es eee 18 Safety instructions and warnings The content below consists of important safety instructions to prevent harm or damage to yourself or others Please be sure to follow the instructions What may occur in case of wrong usage LN Warning Can lead to serious injury or death LN Caution Can lead to harm to persons or damage to property FALTWSY TICDUWT OAL CUSV 7 GRNCREHIS ROBOCS OQ Never do Do not touch Do not attempt to repair or modify the appliance Refer all ser
4. temperature Does not reach If room temperature is below 18 C or above 28 C it may not reach the the temperature setting set temperature This is not a malfunction Is LED turned fast flashing gt Please contact our support desk If issues persist even after following the above please contact our support desk See page 16 After sales services After sales services Please contact our support desk for consultation on repair handling and purchasing of parts Guarantee deadline conditions Guarantee period is one year from the date of purchase e Repair within the guarantee period Our support desk will respond in accordance with the contents of the guarantee e Repair beyond the guarantee period If your Fermenter has a technical issue and is repairable it will be repaired for a charge as per request Holding period of repair for performance parts The manufacturer ensures availability of replacement parts and repairs for up to 6 years after the manufacture of this appliance has been discontinued Replacement parts Spare parts required for the operation of the product Our Support desk Phone Number 0120 481 484 Free dial Open hours 10 00 to 17 00 Mon to Fri Not available Sat Sun national or business holidays Homepage http kneader jp When contacting us we may ask you for the part number serial number and contents of the operation unit Please prepare these before contacting our su
5. d not be disassembled or modified Q Disassembly or modification of heating parts can cause malfunction or fire Inside this appliance and high voltage component there is a high risk of electric shock causing serious physical injury Any internal inspection repairs for this product not disclosed or described in this manual should be referred to our Do not share outlet with other appliances Branch outlet becomes abnormally hot when used with other appliances posing a risk of fire support desk Children are strictly prohibited from using this product Do not keep within reach of children Risk of burns electric shock and injury Leave the front of the appliance free of other objects and keep a space of more than 4 5 cm from sides and walls Close quarters may cause malfunction or a fire Do not place the lower shelf plate directly in front of the heater surface May cause malfunction or fire A Caution Do not use on an unstable surface or on a powdery oily surface S Falling or tipping of this product can cause injury Always use placed on a flat stable surface amp Do not use near fire Fire hazard Never place any objects on top of the appliance Placing things on the appliance surface may cause it to be deformed or damaged Do not pour water over the operating panel Electrical circuit may fail Wipe immediately with a dry cloth when wet Do not place
6. erature Names of parts Main components Top Plate Hollow construction Folding Plate Hollow construction plastic PP Power Plug Mounting Knob 2 Nylon plastic PP Dish part Heater flame resistant plastic ABS ae Shelves plastic ABS Lower convection board Foam PP Doo r plastic PC Temp Display Power switch Red light Temperature sensor Temperature selector knob Humidifcation dish PP Operation manual Recipe Warranty card AN LQ Appliance and accessories First please check whether the following items are all included Appliance Accessories Fermenter heater folding plate top plate door Shelf plates 2 Warranty card Humidification dish Recipes Mounting Knob 2 E User s manual this booklet Convection board Operating Instructions Preparing the Fermenter Place heater on a stable surface ey 2 Unfold the folding plate wit 3 Attach the folding plate to the heater Fit the groove of the folding plate to the heater at the mounting knob Snap the rear folding plate onto the heater pressing against the top of the folding plate for easy attachment Be careful not to apply impact to the Temperature Sensor as that may cause it to disfunction Groove p3 Mounting knob Mounting knob Temp sensor
7. more than a weight of 2kg on the shelf plate Do not place excessive weight on the shelf plate There is risk of damage Do not use for other than fermentation S of bread dough or yeast leaven May overheat and cause accident if used to dry cloth material When disassembling make sure to start from door S Do not clean with flammable solvents KEOGIRDDOET 9 Otherwise door may fall causing risk of injury Do not touch the hot plate See p 6 or humidification dish while in use or immediately afterwards The top of the heating plate may reach a temperature of 100 C Please do not touch Keep unplugged when not in operation e g cleaning or maintenance Risk of injury Be sure to unplug during maintenance Recommendations for appliance operation In the following cases unplug and stop operation immediately Please consult our support desk When power switch doesn t work If power cord or plug is damaged or frayed If the appliance has been deformed from falling If any liquid gets into the appliance frame If the appliance has been exposed to rain and or wind for prolonged periods If the appliance emits smoke or burnt smell does not work normally even in accordance with the Instruction Manual The warning label attached to the appliance contains important notes for your safety Please observe the following precautions e The attached safety label mus
8. n dish ae Humidification dish O Storage method After pre heating is completed In the case of small rolls 3 shelves of oven dishes can fit Shelves can be added as purchase options Internal dimensions WxDxH 310x265x200mm When using a pot manufactured by the Japan Kneader Company set the pot after placing the convection board at the bottom You can bake up to 2 loaves of bread at a time Oven dish 10 1 Using the Fermentator Plug into an electrical outlet Please use an outlet of 100V Do not overload outlet Do not handle plug with wet hands 2 Adjust the knob to the setting temperature 32 34 35 Please set knob to desired temperature 30 36 28 38 27 40 3 Install the Shelf Plate and p the Humidification Dish 4 Turn on the power switch CES POWER Red lamp will flash while heating Once set temperature has been reached red lamp will stay lit Giz 5 Place dough into appliance after set temperature has been reached 6 Take out dough after fermentation is complete 7 After use turn power switch off and unplug Maintenance Please maintain after each use Caution When you are done be sure to remove the plug from the wall outlet Do not use benzine thinner polish scrub brush nylon scrub brush s
9. pport desk Part Number Written on the operation unit or on the cover of the Owner s Manual Serial Number Labelled on the lower surface of the heater Operating Unit Display Info displayed error codes etc About serial number SER We use the serial number as an identification FOR VRAH HS PF100 number for this product TREE 100V ii a F HEE 100W You will find the serial number label on the lower TEDRE 50 60Hz surface of the heater Write the number and date of purchase down in the boxes below in order to confirm the number Ea S RE HA A RRR W000 UA AMA VAAN Rit KKK KKK 2014F EO A promptly Serial number SER is 9 digits dateof month day year 16 17 Specifications Main specifications are as follows Power supply AC 100V for both 50Hz and 60Hz Power consumption 100W Temperature setting range 25 42 C Recommended temperature range 18 28 C Safety features Current temperature fuse Temperature monitoring system automatic switch off function after 24H External dimensions WxDxH 360x350x310mm Cord length approx 1 5m Product weight approx 3 5kg ORmaldk AREA 00V SAlcaxat ANCA SRSEPSRARAORBONE Cle CARA Ftc PIS H ERZBCKEtAL This appliance was designed for use in Japan only where the local voltage supply is AC1OOV and should not be used in other countries where voltage and frequency may vary After sales service fo
10. r this appliance is not available outside of Japan bra REM FT BABIAS ACTA EE 1OOV Figi ATS Be AR Ale RATA CHEK PIDAN ERER AE AR SS o I dE an ASST St A AN Bd Py SS FA S2 re SS BB 00V iit FAS Bl PT Se FASS Rk SE TB cs A fh th ie FA ARIE SAMI ZN EE RRI o EASE SE SUE 100VASLS YH EA HAOL AH SS o AAE AE RSLICt A S st amp 7F5 LEH W Dimensions 360mm 350mm 310mm For purposes of product enhancement certain specifications or appearance may be changed without notice Copying any part or the entire contents of this manual is prohibited The contents of this manual may be changed without notice If you have noticed any errors or omissions please contact our support desk Our Support desk Phone Number 0120 481 484 Free dial Open Hours 10 00 to 17 00 Mon to Fri Not available Sat Sun national or business holidays Homepage http kneader jp Japan Kneader CO LTD 2346 1 Hongo Ebina Kanagawa Japan postal code 243 0417 http kneader jp 602A50400
11. t be in a visible place and may not be covered or hidden e Do not remove or modify the label If the label has become damaged or soiled please request a new one You may contact our support desk to obtain a new label Accidents failure or visible deterioration due to factors such as excessive UV light extreme temperatures humidity detergent oil mold prolonged non use may occur due to natural aging Also general abrasion of parts and abrasion caused by repeated opening and closing of door over several years may lead to deteriorative failure Please always remember to unplug after use to prevent accidents Features of the Fermenter PF100 The Fermenter PF100 can be easily assembled without tools can be folded into a compact size and doesn t take up storage space The Storage Unit employs a double plastic structure lightweight and durable with excellent insulation PAT 4613253 Can be used for up to 24 hours at a time auto off Wide temperature range 25 42 C The Fermenter does not have cooling capacity it will not operate below room temperature Water condensation recovery system patent pending The heater is moisture proof and can be cleaned by spraying lightly But cannot be submerged in water Om KRW N About temperature control function When the inside of this appliance reaches setting temperature the heater will restart automatically and continue operating at the proper temp
12. teel wool etc to clean the device e After use use a cloth to wipe off water droplets that appear on the inside of the fermenter and the door then leave the door open to dry e Please also use a cloth to wipe off excess water droplets that may form while the fermenter is in use e Please wipe off water oil dough etc thoroughly with a cloth e When cleaning and maintaining please be careful not to drop or apply impact to the fermenter e Please keep the inside of the fermenter clean Appliance LN Before cleaning please be sure the hot plate has completely cooled down There is a risk of burns Except for the heater the housing portion of this appliance folding plate top plate door shelves convection board can be washed after disassembly You can clean the surface off lightly with a cloth Please wipe with a dry cloth until completely dry In case more thorough cleaning is necessary continue to wipe and wring out excess water from cloth as needed Mold may form if appliance is stored with moisture remaining inside This can cause deterioration of the insulation and decreased performance After using the fermenter make sure to leave the door open a little to air dry the inside 12 13 Disassembly and storage Turn off power switch and unplug Saag POWER Remove shelf plate humidification dish and convection board A Humidification dish Loosen mounting knob on both sides
13. vicing to authorised repair technicians Do not use near fire Be sure to unplug Use only in dry environment Never use in damp places such as baths washrooms or on wet floors Do not handle plug with wet hands Always obey the display signals Extremely hot Specific explanations on appliance gt OG Use this appliance according to the written cautions and warnings Carefully avoid any accidents DES a A Do not damage or modify cD Remove dust from the power plug S the power cord Dusty plugs are fire and electrical shock hazards Damaged or modified cords are fire and electrical shock hazards Do NOt excessively tisi Do not use plug with wet hands pull or bend the power cord Doing so can damage the cord Damaged cords are fire and electrical shock hazards Electrical shock hazard S Do not place objects on power cord S Do not overload outlets Doing so may produce severed elements and shorted circuits In addition do not damage the power cord If the power cord is damaged it may cause an electric shock or fire May overload circuits causing malfunction and electric shock A Warning Do not wash heating parts S If water gets inside the heater it may cause short circuiting or malfunction T Use with 100V AC outlet only Overload of electrical current may cause electric shock or malfunction Heating parts shoul

PF100

Contents

Download Pdf Manuals

Related Search

Related Contents