TECHNICAL MANUAL DISTELL MEAT FATMETER
Contents
1. Selecting your product samples To create a calibration from scratch you will need a minimum of 20 25 samples of product for the measurements These samples should be evenly spaced across the range of fat content that is expected for the product from very low fat content to very high fat content This will ensure an accurate calibration These graphs show two different situations Graph A shows a sample where all the samples have a similar fat content Graph B shows a sample where the fish cover a wide range of fat content from low to high Range is too Wide range narrow PE Ss pa 2 2 ne i x 5 o o E 5 2 zZ Fat content Fat content s me 5 2 a ea ra 2 gt E lt c lt Reference data Reference data In graph A where the samples all have similar fat content then the custom calibration will only be able to give accurate readings when used on product in the middle range of fat content When it is used on product with high or low fat contents i e outside the range represented by the samples used to create the calibration it will not be able to give accurate data because there are no source data points in those areas DIST ELL com gt Meat Fatmeter Technical Manual Page 6 Measurement of samples using the meter Overview For a given item of produce whether meat or fish a number of samples should be prepared Ideally these will come from multiple sources it is b2. e Blend the entire 300g sample for two minutes to ensure that the sample is thoroughly mixed and homogeneous Take the analysis portions from different parts of the blended sample For example 3 x 15g portions should be taken for triplicate Foss Let chemical analysis Note The Fatmeter has been calibrated against the AOAC approved Foss Let chemical extraction method This method will give the best correlation with Fatmeter measurements The Fatmeter results can be checked against other methods but please ensure that the methodology gives a fair comparison and that it does represent the whole 300g sample DISTCUL com D gt Meat Fatmeter Technical Manual Page 17 Using the Distell Fatmeter Subject Homogenised Meat Represents Fat content of a 300g sample Use on Natural or processed meat e g beef pork poultry lamb sausage burger ham salami etc 1 Selection amp Preparation Randomly select 300g of processed meat from a batch of homogenised meat The blending process can introduce air into the sample so the sample should be compressed before measuring for the most accurate readings 2 Take readings Squeeze and mould the sample to remove any air cavities then form it into a burger or sausage shape Ensure the sample is at least 50mm thick Place the instrument head on the sample at the positions shown below Apply firm pressure to ensure there are no air cavities below the sensor and take readings as shown Fo
3. 11 When you are ready to perform the upload press the Y Read Yes button at the Data Ready prompt File to upload C storage CalibrationDemo dcf Browse Load file When the meter shows Waiting data you can click the Start button in the DMS to begin the upload You can monitor the upload progress on the meter display and also on the computer Note If you cancel the upload before it is complete you will have an incomplete calibration in the meter and measurement results will be unpredictable and inaccurate You should always allow the upload process to finish DISTeCUL com gt Meat Fatmeter Technical Manual Page 12 Comparison with Laboratory Methods Fatmeter measurements vs Foss let method Introduction If you wish to test the accuracy of the Fatmeter measurements and compare the results with the Foss Let laboratory analysis method for an accurate appraisal of its performance it is essential that the techniques employed are the same as those from which the original calibration data were derived When checking the calibration of the Fatmeter against the Foss Let method a key element in the process is the preparation of fish samples for these determinations The purpose of this note is to describe the procedures to be used in the preparation of these samples For detailed instructions please refer to the User Manual and the calibration charts supplied with the meter Background In att
4. the sample is thoroughly mixed and homogeneous Take the analysis portions from different parts of the blended sample For example 3 x 15g portions should be taken for triplicate Foss Let chemical analysis Note The Fatmeter has been calibrated against the AOAC approved Foss Let chemical extraction method This method will give the best correlation with Fatmeter measurements The Fatmeter results can be checked against other methods but please ensure that the methodology gives a fair comparison and that it does represent the whole 300g sample DISTECLL com D gt Meat Fatmeter Technical Manual Page 19 Technical Specifications Sensor Type Microwave Frequency Microwave Power Microstrip transmission line 2 0 GHz 20 MHz lt 2 milliwatts Materials Stainless steel PTFE Display Type LCD 2 lines x 12 characters MFM 1092 LCD 2 lines x 16 characters MFM 992 Sensor Enclosure Material ABS Plastic waterproofed to IP 65 Size 195mm x 100mm x 40mm Weight including batteries MFM 992 375g MFM 1092 600g Hardware Software Capacity Up to 48 calibrations can be stored in each meter and up to 1000 data samples can be recorded before a download is required Software The Distell Data Management System is supplied with each meter and is downloadable from our website Interface Distell meters are supplied with a waterproof USB cable that can be used for periodic downloads as well as real time data
5. JIS Tetll com TECHNICAL MANUAL DISTELL MEAT FATMETER Model MFM 992 small sensor Model MFM 1092 large sensor CE DISTELL Com December 2010 Version 2 7 for use with v2 firmware Contents Introductio nksssenn aaea ei dOr OE ECEE ES NS Np esera 4 Creating Custom Calibrations Measurement methodology Selecting your product samples Measurement of samples using the meter Overview Procedure Once you have measured all of the samples Laboratory analysis of samples In the case of a fish product In the case of a meat product Information required from the laboratory analysis The calibration data file Copying the calibration file from CD Components required for a custom calibration Creating a custom calibration Product settings Recoaro h oot A aaicenisat ee eS ess Uploading Calibrations to the Meter Programming a meter with a new calibration setting In the DMS In the meter Comparison with Laboratory Methods Fatmeter measurements vs Foss let method Introduction Background Preparation amp measurement of meat samples Beef poultry pork horse amp pony sausage meats Conclusion TE Factors affecting results nds Operator 43 Samples specimens 213 Measurement recommendations 14 Technical Specifications Sensor Sensor Enclosure s Hardware y SOPLWONE zenye ased eais i r N ON ATD EE postin ta LEADS ENE
6. NESI ENAT I DEES A CEDEP AEE ANE 19 Declaration of Conformity The Products covered by this Declaration Directives and Standards to which these Products Conform Directives j E D 2 Lao k PEPER DNEPR ae EES PECET P eS PEIEE EEIEIE P AO T OET A TOA ENTEOS A EPE ETN TA OPAT EA Application Data Sheets Application Data Sheet 1 Comments eiiiai Ee These measurements were taken using the recommended procedure using Fatmeter model MFM 1092 21 Conclusion Application Data Sheet 2 Comments Conclusion Application Data Sheet 3 Comments Conclusion DISTCUL com D Meat Fatmeter Technical Manual Page 3 Trading Terms and Warranties Terms and Conditions of Order Acceptance Orders Prices Terms of Payment Terms and Conditions of Sale Retention of Title Returns Liability for Loss or Damage Terms and Conditions of After Sales Warranty GOntaCt Details ansins E E EE E E 26 DISTECUL com gt Meat Fatmeter Technical Manual Page 4 Introduction This Technical Manual is intended to accompany the User Manual that is included with the Distell Fatmeter It has been written to cover some of the more advanced ways in which the Fatmeter can be used as well as to provide some information in the comparison between the Fatmeter and other laboratory methods The information here is not expected to be of particular interest to most Fatmeter users and is aimed at resear
7. OURCE Torry Research Station TRS and Foss Electric SAMPLING METHOD Eight measurements made on 500g hand compressed samples STATISTICS Number of mince samples 33 Maximum lipid content Fosslet 33 8 Minimum lipid content Fosslet 4 6 Regression equation y a bx a 0 607 b 1 004 y is Fatmeter result x is Fosslet Correlation coefficient r 0 981 Standard error 1 14 Comparison of Fosslet and Distell Methods for Lipid Measurement OTRS MMP Distal 99 Fosslet Comments These measurements include those shown in data sheet 1 on the previous page Because the MMP data covers only a narrow range of fat contents this allows them to be seen as actually equivalent to the previous data These measurements were taken using the recommended procedure using Fatmeter model MFM 1092 Conclusion Their inclusion does not significantly change any of the regression parameters DISTCUL com D Meat Fatmeter Technical Manual Page 23 Application Data Sheet 3 TITLE Comparison of Distell Fatmeter and Fosslet methods of lipid analysis PRODUCT Raw minced pork from a retailer in Elgin DATA SOURCE Distell SAMPLING METHOD Eight measurements made on 500g hand compressed samples STATISTICS Number of mince samples 11 Maximum lipid content Fosslet 59 1 Minimum lipid content Fosslet 8 95 Regression equation y a bx a 0 994 b 0 962 y is Fatmeter result x is Fosslet Correlation coeff
8. R CE MARKING FIRST AFFIXED 2000 Ap David T Fulton Proprietor amp General Manager Distell com Old Levenseat Fauldhouse West Lothian Scotland UK DISTECUL com gt Meat Fatmeter Technical Manual Page 21 Application Data Sheets Application Data Sheet 1 TITLE Comparison of Distell Fatmeter and Fosslet methods of lipid analysis PRODUCT Raw minced ground beef from shops and supermarkets in the Aberdeen area DATA SOURCE Torry Research Station SAMPLING METHOD Eight measurements made on 500g hand compressed samples STATISTICS Number of mince samples 14 Maximum lipid content Fosslet 33 8 Minimum lipid content Fosslet 4 6 Regression equation y a bx a 1 14 b 0 977 y is Fatmeter result x is Fosslet Correlation coefficient r 0 979 Standard error 1 46 Comparison of Fosslet and Distell Methods of Lipid Measurement Distell 4 0 5 10 1 20 25 30 35 Fosslet Comments These measurements were taken using the recommended procedure using Fatmeter model MFM 1092 Conclusion The standard error could be diminished by taking more readings DIST ELL com gt Meat Fatmeter Technical Manual Page 22 Application Data Sheet 2 TITLE Comparison of Distell Fatmeter and Fosslet methods of lipid analysis PRODUCT Raw minced ground beef from shops and supermarkets in the Aberdeen area Minced beef samples taken from production at Midland Meat Packers MMP DATA S
9. The data is checked after each entry and any errors in the data will be highlighted in different colours the key to the colours is shown below the data table If the data shows no errors then the DMS will now create a calibration curve based upon data values entered and the new custom calibration will be displayed in the form of a graph There is an option to import this data from a CSV file which may be more convenient for large datasets The CSV file should be formatted as two columns with no header the first column being the Reference value and the second column being the Analysis value DISTCUL com D gt Meat Fatmeter Technical Manual Page 9 4 The fourth stage once the data has been entered is to choose maximum and minimum threshold values This allows you to limit the range of values in the calibration Anything outside of your chosen range will appear as out of range on the meter itself The DMS will attempt to choose sensible values for these but you can override them with your own choice if you wish The fifth stage is to enter the name of the new calibration This is limited to 12 letters symbols or numbers due to the size of the display on the meters The meter will show the calibration name given here on the display __2 Es ae pe Lal 8 ee Lo Li En EF a H R 3 8 Note When measurements using this new custom calibration are downloaded to th
10. as to be measured by laboratory process in order that a like for like comparison can be made between the laboratory results and the calibration data The following pages show two sample calibration charts One is for minced ground meat and most of the Distell meat calibrations should be used with this calibration chart The other is for homogenised meat and should be used with calibrations that are specific to the homogenisation process There are very many calibrations and associated charts available for Distell Fatmeters The full range of calibration charts can be seen on the CD ROM and calibration information can be found on our website at http www distell com information calibrations meat calibrations DISTCUL com D gt Meat Fatmeter Technical Manual Page 15 Using the Distell Fatmeter Subject Minced Ground Meat Represents Fat content of a 300g sample Use on Natural or processed meat e g beef pork poultry lamb sausage burger ham salami etc 1 Selection amp Preparation Randomly select 300g of processed meat from a batch Best results will be obtained with a grind size of 3mm to 8mm Coarser grinds will lead to greater variability in readings 2 Take readings Squeeze and mould the sample to remove any air cavities then form it into a burger or sausage shape Ensure the sample is at least 50mm thick Place the instrument head on the sample at the positions shown below Apply firm pressure to ensure there a
11. brationDemo dcf You can use the Browse jain dhiaaain Bronse button to help you find the Load file file Once you have the I RESEARCH 1 filename click Load to open the calibration file IB Macenet 2 e The third step is to choose Z SPRAT 2 which individual calibrations from the file that you wish to upload to the meter The file may contain more than one calibration so only tick the calibrations that you wish uploaded at this time Important note You should check the version of the firmware that is on your meter this is shown when the meter is switched on Fatmeters with version 2 6 firmware or higher and Freshness meters with version 1 08 firmware or higher can upload multiple calibrations at once but meters with older firmware can only upload one calibration at a time For these older meters only the first ticked calibration will be uploaded even though the DMS will look like it is uploading all of the ticked calibrations To upload multiple calibrations to the older meters you will need to go through this process once for each calibration It is best to tick only one calibration each time The newer firmware will upload multiple calibrations in one operation In the meter Once you have selected the calibration to upload switch meter ON and go to the Add Product option of the Choices Menu on the meter and press the Y Read Yes button DISTECUL com D Meat Fatmeter Technical Manual Page
12. by DISTELL COM UNIT 5 OLD LEVENSEAT FAULDHOUSE WEST LOTHIAN EH47 9AD SCOTLAND TELEPHONE 44 0 1501 770124 FAX 44 0 1501 772424 WEBSITE www distell com EMAIL info distell com
13. capture Batteries Powered by internal rechargeable batteries Nickel Metal Hydride NiMh Charger Power Supply Universal charger power supply also acts as desktop power supply unit Fitted with waterproof connector Input voltage 110V 250V AC 50 60 Hz Output voltage 12VDC 1 2A DISTeCUL com gt Meat Fatmeter Technical Manual Page 20 Declaration of Conformity The Products covered by this Declaration The following Electrical Electronic equipment manufactured by Distell com for measurement control and laboratory use Fish Freshness Meter Torrymeter Fish Fatmeter FFM 692 FFM 992 Meat Fatmeter MFM 1092 MFM 992 Moisture Meter MM 692 MM 992 Directives and Standards to which these Products Conform Directives SAFETY EEC 73 23 EEC 93 68 EEC EMC EEC 89 336 EEC 93 68 EEC Standards SAFETY EEC EN 60950 2000 as amended EMC EEC EN61326 1 2006 EN CISPR 11 2003 Class B EEC EN IEC61000 3 2 2006 EN55011 1998 A1 1999 A2 2002 Class B EEC EN IEC61000 3 3 2002 EN IEC61000 4 2 1995 A1 A2 EEC EN IEC61000 4 3 2002 A1 EN61000 4 4 2004 EEC EN IEC61000 4 5 1995 1 EN IEC61000 4 6 1996 A1 EEC EN IEC61000 4 11 2004 FCC CFR47 2005 Part 15 Sub Part B Class B US Federal code of regulations Consisting of Clause 15 107 Clause 15 109 VCCI Agreement of VCCI 2006 4 Class B In conformance with Table 4 2 Table 4 6 DATE OF ISSUE 1 December 2000 updated 1 July 2008 YEA
14. ce to the customer to that effect Terms of Payment Payment for goods is cash with order Payment for services is due on delivery or completion of services Any other terms of payment must be confirmed in writing from The Company prior to ordering goods and services The Company reserves the right to charge interest on overdue accounts at the monthly rate of 5 above base rate Terms and Conditions of Sale Retention of Title The ownership of any goods supplied by The Company shall remain vested in The Company until full payment has been received The customer shall be entitled to resell the goods or services only as agents of The Company and shall be bound to account to The Company therefore Risk All risks in relation to the goods will pass to the customer upon delivery to the customer or his agents Delivery Delivery shall be deemed to be effected when the goods have been delivered to the address agreed between the customer and The Company or when collected by or on behalf of the customer The Company will endeavour to deliver the goods without delay but shall not be liable for late delivery howsoever caused nor shall such failure be deemed to be in breach of any contract If for any reason the customer refuses delivery then without prejudice to any other rights due to The Company The Company reserves the right to treat the order as cancelled forthwith Returns No returns of goods or services supplied by The Company will be accept
15. chers and other technical users There is in addition a large amount of information on the Distell website at http www distell com The website includes a Frequently Asked Questions section where we address many of the queries that have been raised in connection with the Fatmeter If after reading this document and the information on the website you have questions about or problems with the Fatmeter then please get in touch with us Our contact details are at the end of this manual DISTCUL com D gt Meat Fatmeter Technical Manual Page 5 Creating Custom Calibrations Note a comprehensive guide on creating custom calibrations is available on our website at http www distell com downloads CustomCalibrations pdf Measurement methodology Clearly define your measurement protocols It is important to clearly define your measurement methodology for the product well in advance of the actual measurements To help you decide on the measurement method you will find on the CD ROM supplied by Distell a large number of calibration charts which outline different measurement protocols for different products Your choice of measurement method will be determined by the weight shape and known characteristics of the Product and by the measurement objective Having considered exactly what representative measurement you wish to achieve print out your measurement protocol in detail and follow the method in a consistent and rigorous manner
16. e DMS the calibration name may show as Custom 1 Custom 2 etc according to the slot number see the next stage This only happens with older meter software With latest meter software the DMS will show the name you have selected for the custom calibration Select the grouping method according to instructions available in the Help Section of the DMS Normally you will choose Separate If your meter is an older version then choose Combined This choice governs which calibration slots are available in the next stage The seventh stage is to select the research setting or slot that the new calibration should use In other words which of Meat 1 to Meat 5 will be replaced by your new calibration The documentation that you received with the meter will show you what calibrations are in which slot Where calibrations are combined into a single list you can choose slots 5 to 9 Alternatively where there are separate Product and Research menus available in your meter then you can choose slots 1 to 5 of the Research settings Not all meters have all of these slots available check the configuration of your meter to be certain Your choice should be influenced by whether or not you have already added a custom calibration to the meter if slot 1 is in use for example then you should choose slot 2 or 3 unless you d rather overwrite the calibration in slot 1 You can now save the Data in two formats For uploading your custo
17. ed without The Company s prior written consent Liability for Loss or Damage The Company does not accept liability for damage or partial loss of goods or services under the following circumstances e where there is a clear signed receipt of delivery to the customer where the customer has signed for receipt of goods marked as unexamined DISTCUL com D Meat Fatmeter Technical Manual Page 25 where the customer fails to give notice of any damage or loss within three days of delivery Terms and Conditions of After Sales Warranty Any warranty given is solely confined to the repair replacement of any product supplied or manufactured by The Company directly to the customer All equipment supplied or manufactured by The Company is covered by a twelve month warranty covering parts and labour The warranty commences on the date of shipment or where delivery is by The Company s own staff from the date of delivery The Company warrant that the Equipment shall be free from defects in workmanship and materials Any equipment that is demonstrably defective on receipt by the customer must be returned within seven working days of receipt of goods to qualify for a free of charge replacement Thereafter our sole responsibility shall be to repair or replace the defective product at our discretion upon receipt at our premises The faulty equipment must be received properly packaged protected and insured from Transit Damage The Compan
18. empting a calibration check of the Fatmeter there are three points that must be understood These are The Fatmeter is primarily intended as a tool for those involved in the meat processing industry It provides a non destructive estimate of the fat content of natural and processed meats Please refer to the calibration chart for the product being analysed e The Fatmeter is an averaging instrument and to ensure accuracy especially where large batches of meat product are to be measured several random samples should be taken from various locations on the batch before the specified accuracy of the instrument can be achieved On the other hand the fat content of a single sample can be assessed accurately if eight readings are taken from a well mixed batch of meat e All fat content measurements used in the preparation of the calibration data for the Fatmeter were obtained using a Foss Let Oil Meter This laboratory chemical extraction method requires a 45g sample of the meat product To allow for losses in mincing a sample of the meat product with a minimum weight of 60g should be prepared It is advisable to prepare enough minced material in case a duplicate Foss let measurement is required so that a sample of at least 100g in weight is desirable It is also good practice to carry out triplicate Foss Let measurements on each filtrate Any contamination of the filtrate or of the Foss Let itself will then be immediately apparent Preparation am
19. est to cover as wide a range of fat content as possible Each of these samples will be given a unique ID then measured with the Fat Meter on normally the Research 1 setting This measurement forms part of the reference data set Each sample is then analysed to find the exact fat content The fat content is part of the analysis data set The analysed fat content is paired with the Research 1 measurement Once all the reference analysis pairs have been obtained the custom calibration can be created Procedure Having chosen your samples and prepared your measurement protocol you can proceed to take measurements for each sample using the Meter in the normal manner e Switch the meter on and allow 5 minutes for the sensor to stabilise Check the meter values are in agreement with the meter s check pad e Choose the RESEARCH 1 calibration setting known as the Reference Calibration e Set the number of readings to be averaged between 1 and 8 e Note carefully each set of readings taken on each sample especially the average value The readings will also be stored in meter s memory and you can download the data at any time to the DMS These readings are known as the Reference Dataset e After each set of readings identify each sample with a unique reference and place it in a sealed bag to retain the sample in its original condition Once you have measured all of the samples e Check the number of samples e Check all the samples ha
20. hat may be used as a basis for calibration or measurement Where wholly consistent results are required then the procedures as laid down in the calibration charts supplied must be adhered to or in the case of a different meat product a specific calibration obtained from Distell Please ensure that The specimen sample has been prepared as per guidelines and that the constituents of the meat product have not been artificially changed Where the composition of the product has been changed from the natural state then for really accurate results a specific product calibration must be used DIST ELL com gt Meat Fatmeter Technical Manual Page 14 The specimen sample is not dehydrated As the Fatmeter is actually measuring the water content as part of the measurement of oil content it is important that the specimen has not been allowed to dry out Where product has been frozen it must be allowed to thaw defrost completely before taking measurements Measurement recommendations Each calibration that is available for the meter has several points that you should be aware of L 2 The exact meat product that the calibration should be used with The measurement method that should be followed when using the calibration The representation of the calibration i e when the Fatmeter shows a fat measurement what does that measurement actually represent The preparation and processing involved if the meat product sample w
21. icient r 0 986 Standard error 25 Comparison of Distell and Fosslet methods of lipid measurement 60 50 se 40 2 30 A 20 10 0 o 10 20 30 40 50 60 Fosslet Comments There is high correlation between these methods although the number of data points is small These measurements were taken using the recommended procedure using Fatmeter model MFM 1092 Conclusion The standard error is large due to both this small number of samples and the large range of fat contents More samples would reduce this considerably DISTECUL com gt Meat Fatmeter Technical Manual Page 24 Trading Terms and Warranties In line with most manufacturers the products that we manufacture and sell are covered by a comprehensive warranty In order that all customers are fully aware of the terms and conditions of order acceptance terms of sale and after sales warranty we have summarised below our current terms for reference Terms and Conditions of Order Acceptance Orders An order received by Distell com hereinafter referred to as The Company is deemed to be an offer to purchase by the customer and subject to the conditions herein contained which will be deemed to be accepted by the customer upon delivery of the goods Prices The prices quoted are subject to stock availability and whilst every endeavour will be made to supply at quoted prices The Company reserve the right to revise prices at any time prior to delivery upon giving noti
22. in the DMS This will open the Custom Calibration Data window The following steps should be followed 1 The first stage is to locate the DCF file containing the Reference Calibration For RESEARCH 1 this file should be on the CD you received with your meter under the file reference Calibration Module For some older units however this file was not available so please get in touch with Distell to obtain it Click on the Browse button to navigate to the file then click Load to load the reference calibration data from the file Alternatively you can p C G drag the file from the Windows 2 Choose reference calibration desktop or a file explorer window and drop it on the Create Custom Calibration window 2 The second stage is to select the reference calibration you wish to use z 1 Locate reference calibration The DCF file in stage 1 may contain lt 7 O multiple calibrations though only those used in the Fatmeter s Research C menu are able to be used for this Select the appropriate calibration from the drop down list and the DMS will use this file as your Reference Calibration for calculating new custom calibration You must choose the calibration setting that was used to take the measurements typically this will be Research 1 3 Using the table enter the values for Reference Dataset in left hand column and Analysis Dataset in right hand column for each pair of samples
23. m calibration to the meter using the DMS save as a Distell Calibration File DCF The uploading process is discussed in the next section For exporting to a spreadsheet or database save as a Comma Separated Value file CSV In this form the data is presented as a series of 1000 discrete data points that reflects the measurement range of the meter Note that the best fit type is best left at Exponential for a natural calibration DIST ELL com gt Meat Fatmeter Technical Manual Page 10 Uploading Calibrations to the Meter Programming a meter with a new calibration setting Note a more comprehensive guide on uploading calibrations is available on our website at http www distell com downloads UploadingCalibrations pdf Your meter is shipped with several calibrations pre installed but if you have purchased an additional calibration or you have created a custom calibration then this option allows you to upload it to your meter Note each calibration is unique to a specific meter because it has been tuned to the exact electronic profile of the sensor in the meter You can upload a calibration to a different meter but it will not give accurate results To upload a calibration to your meter proceed as follows In the DMS e Open the DMS select the File menu then Upload Calibrations Locate the Custom Calibration file that you wish to upload This should File to upload have a DCF file extension C storage Cali
24. p measurement of meat samples Beef poultry pork horse amp pony sausage meats The preparation procedures for all the above meat products are basically the same The usable flesh of the animal i e excluding the head bones offal etc is uniformly minced as required A portion of the minced meat of approximately 300g is randomly selected from the batch hand pressed into a solid mass and placed in a suitable glass dish or bowl The depth of the material should be at least 50mm as a flat burger shape or 60 100mm if shaped into a round sausage shape The sample should be wider than the sensor head so that the sensor head is entirely in contact with the sample The sensor head is then pressed firmly into the meat to ensure good contact over the whole of the sensor head but not so firmly that the mass of the material is penetrated significantly After completing such a measurement there should be just a slight indentation in the surface of the minced meat product a few millimetres at the most DISTCUL com D Meat Fatmeter Technical Manual Page 13 This procedure is repeated eight times at different points on the sample to obtain the average Fatmeter reading Please refer to measurement sites section for details on this process A sample of the minced meat of approximately 45g is then taken for analysis by Foss Let using the normal Foss Let methodology For the greatest accuracy of any calibration check it would be advisable to
25. perform as many Foss Let analyses on the mince as the sample allows This then will take account of any inconsistency in the fat distribution within the sample Conclusion Using the techniques described above it should be possible to achieve accuracies 95 confidence interval within the following limits Fat Oil Reading Accuracy 4to 10 1 0 11 to 20 1 5 21 to 30 2 0 31 to 40 3 0 41 Rising to 4 0 Factors affecting results The results obtained with the Meat Fatmeter can be affected by various factors Operator The operator of the equipment must use the instrument in a consistent manner and follow the guidelines set out in the User Manual and calibration charts Take care that The sensor head is fully in contact with the sample or specimen prior to taking a reading and not at an angle to the surface If the sensor head is not fully in contact with the sample then the Fatmeter may display an erroneous high reading The sensor head is clean and no excess oil or water is present The sensor head is not removed from the sample before releasing the Read Yes button Samples specimens Where possible follow diligently the guidelines within the User Manual It is possible to use the Fatmeter on meat products other than those for which the instrument is calibrated and in different ways however the results obtained will not necessarily be accurate They should allow however reproducible results t
26. que to the meter whose reference calibration was used To create a custom calibration for more than one meter use each meter s individual reference calibration along with the same reference and analysis datasets Components required for a custom calibration A Custom Calibration for your Fatmeter is produced from combining the following datasets The Reference Calibration for your Meter RESEARCH 1 e The Reference Dataset Fatmeter values of sample product produced using the reference calibration The Analysis Dataset Laboratory values of sample product Creating a custom calibration Each meter is shipped with the following calibration settings DISTECUL com gt Meat Fatmeter Technical Manual Page 8 Product settings A minimum of four standard product calibrations Research settings One research calibration known as RESEARCH 1 and which is used for reference when creating your own custom calibrations Five vacant slots for installing custom calibrations These slots are pre programmed with Fish 1 to Fish 5 but these calibrations do not contain valid data The data that makes up these product datasets is called a calibration The DMS provides the capability to create a new calibration and upload the calibration into one of the five vacant slots in the research group The process of creating a custom calibration in the DMS follows To begin select Create Custom Calibration from the File menu
27. r a burger shape take four readings from For a sausage shape take eight the top then turn it over and take four from readings from around the surface of the bottom the sample gt 50 mm To ensure accurate measurements keep the read button pressed until the reading is stable Once the reading is stable release the read button It is important that you release the read button before removing the sensor from the sample 3 What do these results represent After eight readings the readout shows the average fat content of the 300g sample Calibrations using this process are BEEF 2 BEEF 5 CHICKEN 2 CHICKEN 3 and CHICKEN 4 DISTECUL com gt Meat Fatmeter Technical Manual Page 18 Laboratory Analysis Subject Homogenised Meat Represents Fat content of a 300g sample Use on Natural or processed meat e g beef pork poultry lamb sausage burger ham salami etc Preparation of samples It is very important that the laboratory analysis is done correctly and truly represents ALL of the sample as represented by the Fatmeter measurements Please prepare the samples for analysis as follows e Always ensure that the entire sample that was measured by the Fatmeter is sent to the laboratory for analysis Where a rigorous comparison is required then it is necessary to ensure that the laboratory is fully aware of these preparation requirements e Blend the entire 300g sample for two minutes to ensure that
28. re no air cavities below the sensor and take readings as shown For a burger shape take four readings from For a sausage shape take eight the top then turn it over and take four from readings from around the surface of the bottom the sample gt 50 mm e To ensure accurate measurements keep the read button pressed until the reading is stable Once the reading is stable release the read button It is important that you release the read button before removing the sensor from the sample e Itis normal to find a wide variation in readings especially in a coarse grind 3 What do these results represent After eight readings the readout shows the average fat content of the 300g sample DISTECUL com gt Meat Fatmeter Technical Manual Page 16 Laboratory Analysis Subject Minced Ground Meat Represents Fat content of a 300g sample Use on Natural or processed meat e g beef pork poultry lamb sausage burger ham salami etc Preparation of samples It is very important that the laboratory analysis is done correctly and truly represents ALL of the sample as represented by the Fatmeter measurements Please prepare the samples for analysis as follows e Always ensure that the entire sample that was measured by the Fatmeter is sent to the laboratory for analysis Where a rigorous comparison is required then it is necessary to ensure that the laboratory is fully aware of these preparation requirements
29. ve been clearly marked with a unique reference e Download your sample data from the meter and obtain a printout for reference as well as saving the data on the computer e If the laboratory analysis is not being carried out immediately store all the samples carefully to preserve their original condition The samples are now ready to send to laboratory for analysis by the method of your choice The laboratory results are referred to as the Analysis Dataset Laboratory analysis of samples It is important that the laboratory personnel are fully informed of your sample requirements Questions to consider are e What portion of the sample do you wish to analyse e What do you wish the analysis to represent In the case of a fish product e Is it the whole fish carcass e Is it the trimmed fillets of the fish e Is it a defined section of the fish In the case of a meat product e Is it a standard 300 gm sample of minced product 3 8mm grind Is it a whole piece of meat DISTCUL com D gt Meat Fatmeter Technical Manual Page 7 Information required from the laboratory analysis Fat content e Water content Total solids Calorific bio energetic values Once you have received the data from the laboratory match each laboratory sample value the Analysis Dataset with the corresponding Fatmeter sample value the Reference Dataset This will give you a list of paired results One way to retain this data is to create an e
30. xtra column in the DMS Grid table and record the laboratory value alongside the Fatmeter sample data Once completed you are ready to create custom calibration using the DMS The calibration data file At this point it is a good idea to locate the calibration data file supplied by Distell on your Information CD and copy to your computer Copying the calibration file from CD Find the CD that was supplied with the meter and put it in the computer Note that you have to use the specific CD for the meter since the data on the CD is unique to the meter e Open the CD contents typically via My Computer from your desktop or the Start menu Browse the files until you find the Installation Files folder then highlight the ReferenceCalibration_xxxxx DCF file Right click on the file and choose Copy from the menu e Open your My Documents Folder If you wish to place the calibration file in a sub folder then open that sub folder Right click on an empty space in the folder then click Paste from the menu e Also it is a good idea to use this folder to save your own custom calibrations so that they are available for creating future work Note Remember that the calibration file on the CD is unique to the meter with the serial number shown on the CD The custom calibration that is produced from this process is partially derived from the reference calibration and so the custom calibration is also uni
31. y accepts no responsibility under the warranty for any product that has been opened tampered with reprogrammed altered modified or misused in any way and in no event shall the company be liable for incidental consequential indirect or special damages including but not limited to damage arising from the loss of use of the product system or profits or any claim against the company by any other party This warranty is in lieu of all other warranties whether expressed or implied including without limitation implied warranties of merchantability and or of fitness for a particular purpose Following the expiry of the manufacturer s warranty we strongly advise our customers to avail themselves of our comprehensive service and maintenance contract This contract covers your equipment and where applicable your installation for a period of one two or three years Note that all labour and parts are covered by this service contract but shipping packaging and insurance are payable by the customer For further details please contact our offices In the event of a warranty claim or a service requirement please contact our Returns Department Details of address and telephone numbers are shown at the rear of this manual For a copy of the complete Terms and Conditions please contact our sales office or distributor DISTECULL com gt Meat Fatmeter Technical Manual Page 26 Contact Details DISTELL MEAT FATMETER is manufactured in the UK
Download Pdf Manuals
Related Search