Technical Support
Contents
1. 1 7 HDMI Splitters over 2 UTP Vanco Part Numbers 280718 1x8 280714 1 4 pport com 800 626 6445 For optimum performance read these instructions caref connecting operating or ad iis product Please keep this manual for future reference This product is 100 inspected and tested in the United States to verify HDMI performance parameters WARNING 1 Do not expose this unit to water moisture 6 Only clean unit with a dry cloth or excessive humidity Unplug unit during lightening storms or 2 Do not install or place this unit in a built in when not used for an extended period cabinet or other confined space without of time A surge protector is strongly adequate ventilation recommended 3 To prevent risk of electrical shock or fire 8 Protect the power cord from being walked hazard due to overheating do not obstruct on or pinched particularly at the plugs unit s ventilation openings 9 Use unit only with accessories specified by 4 Do not install near any source of heat the manufacturer including other units that may produce heat 10 Refer all servicing to qualified personnel 5 Do not place unit near flames CAUTION HDMI is a very complex technology requiring continuous authentication of the signal and the same video resolution and audio settings on all electronic equipment in the system When there are multiple sources and displays the video resolution an2. LIABILITY STATEMENT Every effort has been made to ensure that this product is free of defects The manufacturer of this product cannot be held liable for the use of this hardware or any direct or indirect consequential damages arising from its use It is the responsibility of the user and installer of the hardware to check that it is suitable for their requirements and that it is installed correctly All rights are reserved No parts of this manual may be reproduced or transmitted by any form or means electronic or mechanical including photocopying recording or by any information storage or retrieval system without the written consent of the publisher Manufacturer reserves the right to revise any of its hardware and software following its policy to modify and or improve its products where necessary or desirable This statement does not affect the legal rights of the user in any way LIMITED WARRANTY With the exceptions noted in the next paragraph Vanco warrants to the original purchaser that the equipment it manufactures or sells will be free from defects in materials and workmanship for a period of one year from the date of purchase Should this product in Vanco s opinion prove defective within this warranty period Vanco at its option will repair or replace this product without charge Any defective parts replaced become the property of Vanco This warranty does not apply to those products which have been damaged due to accident una
3. i E IR 1 per display for Matrix Switches Extenders RX Pigtail 1 per source for Splitters www vanco 1 280718 PRODUCT IMAGES Splitter a i Over UTP ofr 4 in 8 Over 800 626 6445 7 0 280714 PRODUCT IMAGES ma SEAS HDMI Splitter zi m gt www vanco TROUBLE SHOOTING Best results are usually achieved when the source and display resolutions are the same If resolutions differ the splitters will try to adjust the signal to match the resolution of the HD TV with the lowest resolution This will result in a picture with a lower resolution on the other HD TV sets If you do not get audio and video see if you can use the set up menu on the TV to adjust the audio settings and the video settings If the HDMI control circuit can t establish a hand shake then there usually will be no audio or video and a blue or black screen with a statement like this protocol not supported or weak signal If you get the above messages re set the splitters using the button on the front panel Alternately you can disconnect all of the HDMI and power cables wait 10 or 15 minutes for any voltages to decay and then connect all of the cables from the source to the splitters and to the display If you still have trouble then try the hot plug concept Turn on the source and plug the HDMI cable to it and then power up the splitters and plug the
4. 19 Rack or Shelf Mounting DC UL Listed Power Supply for 1 x 8 Splitter Unit 1 x 8 Splitter Dimensions 17 25 W x 2 H x 8D Receiver Dimensions 8 Total 1 75 W 875 x 3 25 D Cat6 Cables High Speed Chip Set that Supports 3D and 4K x eK Full HD1080P 60HZ HDCP Compliant Super IR IR transport channel can be forward or backward an IR adapter and transmit and receive pigtails are needed Supports Digital Audio Format DTS HD Dolby True HD LPCM7 1 ACS DTS DSD S00 626 6445 HDMI 1 x 4 Splitter over 2 UTP with IR Part 280714 e Unique Circuit Design Allows for Protection against High Voltage and Peak Currents e Tested for Compatibility with all leading HD Video brands e Tested with Dolby 7 1 Home Theater Systems Locking Compatible Shelf or Wall Mounting e QV DC UL Listed Power Supply for 1 x 4 Splitter Unit e 1 x 4 Splitter Dimensions 19 5 W 1 125 H x 6 25 D Allows 1 HDMI Source to be Connected to 4 HDMI Displays Devices over Dual Cat5e Cat6 Cables Transmission Range Extends 1080p resolutions up to 100 ft over Cat5e Cables Extends 1080 resolutions up to 110 ft over Cat6 Cables High Speed Chip Set that Supports 3D and 4K x eK Full HD1080P 60HZ HDCP Compliant Super IR IR transport channel can be forward or backward an IR adapter and transmit and Receiver Dimensions 4 Total 1 75 W receive pigtails are needed 75 3 25 D e
5. cable into it then plug the output cable into the splitters and finally turn on the display and plug the cable splitters onto it This activates all of the devices in order and results into a signal being plugged in to a device that is on and will try to connect to the signal Most of the major player and display manufacturers employ a proprietary control channel to communicate between devices from the same manufacturer Sometimes this could interfere with the HDMI control circuit or the authentication of the signal Call the manufacturer if you experience this problem Sometimes a player an audio video receiver or a cable satellite box may not have the latest software update and needs to have this downloaded from the manufacturer s web site If the above actions do not result in a satisfactory result focus attention on the Cat 5e or Cat 6 cables used The HDMI signals run at digital data rates which are at least ten times faster than for conventional Ethernet If 8 position modular plugs are attached in the field the connection may not be able to support the HDMI signal This is why factory terminated assemblies are strongly recommended To determine if the field assembled cables are at fault move the source close to the display and connect with a 3 ft or 6 ft computer cable assembly If you have problems with the IR control circuit make sure that the IR RX pigtail is plugged into the IR Adapter and the toggle is set to IR S00 626 6445
6. Supports Digital Audio Format DTS HD Dolby True HD LPCM7 1 ACS DTS DSD HDMI VO PSION tent HDMI v1 4 with 3D FHIJCP Versltfi HDCP1 2 1080P 1080i 720P 576i 480P 480i deep color 24bit 36bit LPCM Dolby AC3 DTS7 1 DSD 5 0Volts P P ft 24AWG Cable ft 24AWG Cable 66 66 6 75Gbps 5 to 9096RH No Condensation 15 to 55 DegreesC 5 to 131 Degrees F Input AC 50Hz 60Hz 100 240V Support HDMI resolution Support video color bit Support Audio Format Input Video signal Output cable Input cable distance Data transfer speed Operating Humidity range Operating Temperature Power adapter format Power Supply NOTE 100 ft distance with 2 x Cat 5e and 110 ft distance with 2 x Cat UTP cables www vanco 1 PACKAGE CONTENTS Before attempting to use this unit please check the packaging and make sure the following items are contained in the shipping carton One HDMI Splitter Power Supply 4 Receivers included with 1x4 and 8 Receivers included with 1x8 Product Manual Two Mounting Ears for Part 280718 CONNECT AND OPERATE Connect the signal source such as Blu Ray Player Play Station 3 audio video receiver cable or satellite receivers and computers equipped with HDMI output interfaces with a sho
7. d audio setting on all connected units must be adjusted to correspond with that of the display having the lowest video and audio capability www vanco Pele aa Super IR Control These units have the capability of being controlled via IR signals The splitter can be controlled from the display This is accomplished by using an optional IR Receiver pigtail Part 280721 pointing away from the display s which can be connected to the receiver boxes at each display The IR Transmitter pigtail Part 280720 is then connected to the splitter and pointed at the source s A remote control is used at the display to select the splitter inputs and outputs Over Current Over Voltage Protection The circuit boards are equipped with both over current and over voltage protection and automatically power down if these are encountered The power circuit will restore itself automatically once the excessive current or voltage conditions are rectified 1 x 8 Splitter over 2 UTP with IR Part 280718 Allows 1 HDMI Source to be Connected to 8 HDMI Displays Devices over Dual Cat5e Cat6 Cables e Transmission Range Extends 1080p resolutions up to 100 ft over Cat5e Cables Extends 1080p resolutions up to 110 ft over Unique Circuit Design Allows for Protection against High Voltage and Peak Currents Tested for Compatibility with all leading HD Video brands Tested with Dolby 7 1 Home Theater Systems Locking HDMI Compatible
8. f the individual IR Transmitters can illuminate any of the IR receivers built into the sources This will allow the remote that is supplied to switch the sources sending an HDMI signal to a display When using cable television or satellite receivers and audio video receivers as sources of HDMI signals please check with the manufacturer to make sure that the output of their device provides the 5 VDC power required for the proper operation of both the HDMI signal as well as the Super IR system Too low of a voltage will adversely affect the operation of both While playing HD audio and video content turn on each HD TV set in order starting with that connected to output port 1 on the splitter and use the Information button on the remote to check for a 1080p 60 Hz 120 Hz or 24 Hz resolution If you have difficulty getting a picture go to the TV s set up menu and adjust the resolution A 24 Hz vertical refresh rate may work better than a Hz or higher vertical refresh rate and is currently used for 3 D programming S00 626 6445 CONNECTION DIAGRAM 5 Receiver 6 Wis 2 t IR Receiver Dual UTP Cable ee ERASER pa Splitter num Over UTP 1 080 IR Transmitter 1 Per Source Single Input Source Super IR Control System Over UTP Cable Blu Ray HDTV Player Sender Receiver IRTX Pigtail IR Remote EA
9. rt high speed HDMI cable to the HDMI splitter input Connect the splitter output RJ 45 ports using dual runs of Cat 5e or Cat 6 UTP cables to included receivers which do not require a power supply It is strongly recommended that factory terminated cable assemblies be used and their length shall not exceed 100 ft of Cat 5e and 110 ft of Cat 6 Connect the HDMI output from the receivers to high definition display devices such as HD LCD HD DLP and HD projectors with HDMI input interfaces Use high speed HDMI cables that are recommended for the distances that are required for each connection These splitters are powered by an external power supply which is included Connect power first to the source then to the splitters and then to each HD TV or projector The splitter can be controlled from the display This is accomplished by using an optional IR Receiver pigtail Part 280721 pointing away from the display s which can be connected to the receiver boxes at each display The IR Transmitter pigtail Part 280720 is then connected to the splitter and pointed at the source s A remote control is used at the display to select the splitter inputs and outputs In switches and splitters with multiple inputs the Super IR system can also be used to control the operation of the switch or splitter For controlling the switch or splitter operating with multiple sources it is important that these sources be stacked together in one rack so that any o
10. ted and tested to insure highest product quality and trouble free installation and operation The testing process utilizes the types of high definition sources and displays typically installed for entertainment and home theater applications For additional information such as helpful installation videos glossary of terms etc please visit www vanco com S00 626 6445 co International ia Illinois 60510 800 626 6445 fax 630 879 9189 visit www vanco1 com
11. uthorized alterations improper repair modifications inadequate maintenance and care or use in any manner for which the product was not originally intended Items integrated into Vanco products that are made by other manufacturers notably computer hard drives and liquid crystal display panels are limited to the term of the warranty offered by the respective manufacturers Such specific warranties are available upon request to Vanco A surge protector power conditioner unit or a uninterruptible power supply must be installed in the electrical circuit to protect against power surges If repairs are needed during the warranty period the purchaser will be required to provide a sales receipt or other acceptable proof of purchase to the seller of this equipment The seller will then contact Vanco regarding warranty repair or replacement www vanco TECHNICAL SUPPORT In case of problems please contact Vanco Technical Support by e mail at support Vanco1 com or call 1 800 626 6445 between the hours of 8am and 5pm central US time zone on Monday through Friday When calling please have the Model Number Serial Number affixed to the bottom of the unit and Invoice available for reference during the call Please read this Instruction Manual prior to calling or installing this unit since it will familiarize you with the capabilities of this product and its proper installation All active electronic products are 100 inspec
Download Pdf Manuals
Related Search