1018 Lumenator
Contents
1. Auto Speed setting 00 is fastest lat O Auto Mode 0 fade mode Auto Mode at 1 Auto Mode 1 3 color change mode lat 2 Auto Mode 2 7 color change mode Ad 0 Audio Mode 0 Fade mode Audi audio mode Ad 1 Audio Mode 1 3 color change mode Ad2 Audio Mode 2 7 color change mode Ad 3 Audio mode 3 strobe with 7 color CoLr show color mode R for Red G for Green B for Blue Hr Power on time Xxxx Time in hour for Power on r Red Calibrate Mode CCAL color Calibrate g Green Calibrate Mode b Blue Calibrate Mode xxxC Temperature in C xxx Temperature Calibrate tEp temperature tEp temperature Chan CH 4 4 Channel Mode ChaniCH 6 6 Channel Mode Chan CH 9 9 Channel Mode StAt HoLd Hold DMX status when no DMX signal OFF Light OFF when no DMX signal MAIN FUNCTIONS Axxx Current DMX Address A Setting DMX Address using Buttons 1 Press Enter Button when the display shows Axxx Menu then adjust the DMX address by pressing UP or DOWN to get to desired Base address channel number PRESS ENTER to confirm or ESC return to Menu B Setting DMX address by Controller 1 Set the DMX Value of Channel 5 to 10 15 Channel 6 to 20 26 Channel 7 to 30 36 Channel 8 to 40 46 Then the fixtures connected to the controller will enter the address setting mode 2 Set the DMX value of Channel 1 from 0 59 then you will see the firs2. USED OUTSIDE and are usually hardwired into APPROVED OUTSIDE WEATHER PROOF JUNCTION BOXES Do not plug into standard unprotected outlet except for test purposes DMX 512 Control Connection Product has a DMX Input fitted with 3 pin XLR outdoor connectors Screened cables in compliance with EIA 485 specifications and the following characteristics MUST be used for connections 2 Conductors plus screen 120 Ohm impedance Low capacitance Max transmission rate 250 kBaud DMX 512 Connection with DMX Terminator For installations where the DMX cable has to run a long distance or is in an electrically noisy environment such as a Dance Venue it is recommended to use a DMX Terminator This helps in preventing ghosting signal corruption of the original signal by electrical noise The DMX Terminator is simply an XLR plug with a 120 ohm resister between pins 2 and 3 which is plugged into the output XLR socket of the last fixture in the chain DISPLAY Menu Continued CnFg parameter config Chan CH 7 7 Channel Mode diCS Inst Instant Mode Light on off instant DELA Delay Mode Light on light off delay for 5 Seconds LoCc Loc Active self lock keyboard no operation on the button for 30 seconds Unloc Deactivate self lock keyboard if NO operation on the button for 30 seconds Menu 1 Menu 2 conf Menu 1 Axxx address DMX Address Setting SPed Auto Speed
3. when show Hr Menu appears then you will see the run time is on When the time is over 9999 hours then the first number will be a hexi decimal for example A999 means 10999 hours B999 means 11999 hours C999 means 1299 hours Once the first number is over 1599 the first number will be null B Clear the Time Press ENTER Button when show Hr Menu appears and then press up and down button AT the same time for 3 seconds Then the time will clear to 0000 simultaneously CCAL Color Calibrate Press ENTER button when menu reads CCAL Then choose the r g b calibrate by pressing UP or DOWN button Press ENTER to enter individual colors Adjust brightness of the color you choose pressing UP or DOWN button Press ENTER to confirm or ESC to return to main menu tEp Temperature Information Press ENTER button when menu reads tEp You will see the temperature of the LED in unit If there is no temperature sensor it will read err CAUTION The brightness WILL decrease gradually when the LED temperature is over 120F and if it is over 150F unit will BLACK OUT protection SAVE the DMX address set by the controller 5 CnFg PARAMETER CONFIG Press ENTER button when menu reads CnFg Then choose the parameters by pressing UP or DOWN button then press ENTER CHAn CHOOSE THE CHANNEL MODE Choose the Channel mode by pressing UP or DOWN button then press ENTER to confirm Ch3 is 3 channel mode Ch5 is 5 channel mod
4. 1018 IP65 INSTRUCTION MANUAL INTRODUCTION The entire staff of Meteor would like to thank you for selecting the 1018 IP 65 LUMENATOR as your fixture of choice We have expended that extra effort to make sure you are more then pleased and satisfied with your purchase Please check and make notice of any external cosmetic box damage caused by transportation Notify your dealer he in turn will notify us If there is any damage either inside the box or outside the box DO NOT INSTALL THE DEVICE There is a possibility that something may have come undone or unplugged Unpack the Lumenator Inside the box you should find Protective packing The Lumenator One power cable One XLR cable Instruction manual DESCRIPTION FEATURES 16 BIT DIMMING OVER TEMPERATURE Protection Can set DMX Address via Controller 4 6 or 9 DMX channels selectable for numerous applications Automatic Identify Master Signal and change to Slave mode Step less RGBW COLOR mixing Color CALIBRATE function Equipped with 18 10w LEDS 4 in 1 Switch mode power supply 90v 240v AC SAFETY INSTRUCTIONS This lighting fixture has left our factory in perfect condition In order to maintain this condition and to ensure safe operation it is absolutely necessary for the user to follow the instructions and caution notes written in this user manual This fixture falls under protection class 1 Therefore it is essential t
5. ENUINE REPLACEMENT PARTS INSTALLATION SAFETY This fixture must be installed at a vibration free Oscillation free and Fire resistant free location Although the unit is rated as IP65 that DOES NOT MEAN IT CAN BE SUBMERGED or USED UNDERWATER
6. e CH9 is 9 channel mode DiCS CHOOSE INSTANT or DELAY Mode TECHNICAL SPECIFICATIONS WATER PROOF IP65 RATED POWER CONSUMPTION 120 W IP65V POWER IN IP65 PASS CONNECTOR IP65 3 PIN DMX IN CABLE IP65 DMX 3PIN OUT POWER SUPPLY 100V 240V AC 50Hz 60 Hz NET WEIGHT 9lbs SHIPPING WEIGHT 11lbs METEOR LUMENATOR DMX PROFILE 4CH 6CH 9CH Values Functions 1 1 0 255 Master Dimmer 0 100 1 2 2 0 255 Red 0 100 2 3 3 0 255 Green 0 100 3 4 4 0 255 Blue 0 100 4 5 5 0 255 White 6 6 8 255 strobe slow to fast 7 0 9 Null 7 10 19 Red 20 29 Green 30 39 Blue 40 49 White 50 59 Yellow 60 69 Magenta 70 79 Cyan 80 89 RGB 90 95 ALL ON 96 127 Macro 1 128 159 Macro 2 160 191 Macro 3 192 255 Macro 4 8 0 255 Speed of Macros slow to fast 9 00 255 Speed of Dimmer fast to slow CLEANING and MAINTENANCE We recommend frequent cleaning of this fixture Please use a soft lint free and moistened cloth NEVER USE ALCOHOL or any KIND OF SOLVENTS CAUTION ALWAYS DISCONNECT POWER FROM THE FIXTURE BEFORE ANY TYPE OF CLEANING OR MAINTENANCE IS PERFORMED There are no serviceable parts inside this unit Maintenance and service operations should be carried out by only authorized dealers or qualified service technicians If you need any spare parts PLEASE use only AUTHORIZED factory specified G
7. hat the device should be grounded A qualified person must carry out the Electrical connection to power If the external flexible cable or power cord of this fixture is damaged it HAS to be and will be replaced by the manufacturer or service agent or a similarly qualified person in order to avoid hazard or electrical shock Make sure that the available voltage is NOT higher than stated at the end of this instruction guide manual Make sure the power cord is NEVER crimped or damaged by sharp edges If it is replacing a cable must be done by an authorized dealer trained in electrical repair Always disconnect from electrical MAINS when the 1018 Lumenator is NOT in use or before cleaning it Definitely before cleaning it You could wind up getting a severe electrical shock Only handle power cord by the PLUG Never PULL out the plug by tugging on the power cord Very strong possibility of getting serious electrical shock NEVER LOOK DIRECTLY INTO THE LIGHT FIXTURE WHILE IT IS POWERED UP SENSITIVE PEOPLE MAY SUFFER FROM EPILECTIC SHOCK far fetched BUT IT COULD HAPPEN IMPORTANT Damage caused by the disregard of this user manual IS NOT SUBJECT TO WARRANTY The DEALER is not and will not ACCEPT LIABILITY for any resulting defects or problems caused by not following instructions IGNORANCE is NOT A VALID WARRANTY ISSUE PLEASE MAKE NOTE The power cord has been deliberately left OFF as most IP65 FIXTURES ARE
8. t number of the address change Channel 1 value 10 For example when you set the value of channel 1 to 20 the first DMX address number will be 2 20 10 2 3 Set the DMX value of Channel 2 from 0 99 then you will see the first number of the address change Channel 2 value 10 For example when you set the value of channel 2 to 30 the first DMX address number will be 2 30 10 3 4 Set the DMX value of channel 3 from 0 99 then you will see the first number value 10 For example when you set the value of channel 1 to 40 the first DMX address number will be 3 40 10 4 5 Set the DMX value of Channel 4 from 255 then you will address change Channel 3 4 5 Set the DMX value of Channel 4 from 255 then you will see SAVE the DMX address set by the controller CAUTION It won t save the address if the ADDRESS number is OVER 512 6 Setting the value of Channel 5 8 out of the value range shown on the step 1 will cause the device will exit the setting address mode SPEd Auto Run Mode Setting Auto Run Mode 1 Press ENTER button when Auto Menu appears then adjust the mode by pressing UP or DOWN button Setting Audio Run Mode 1 Press ENTER button when Audi Menu appears then adjust the mode by pressing UP or DOWN button CoLr Show Color Mode 1 Press ENTER button when CoLr Menu appears then adjust the mode by pressing UP or DOWN button HR Show the time Power ON A Show Time Press ENTER Button
Download Pdf Manuals
Related Search