SW300A+SW200D2 manual_封面
Contents
1. permission is authorized2. USER S MANUAL SUPERJACK SWING GATE OPENER 2 50m max 2 50m max 250kg max 250kg max Important Safety Advice 1 Knowledge of the relevant electro technical regulations is required 2 Training in use and maintenance of safety eguipments is necessary 3 Always put mains and control cables separately 4 Test each individual item before initial operation 5 Make familiar with the use of the system before initial operation Content of the Kit Sa A Y 0 e Kuud exl x8 x8 E Ce o O K i TE eae i l x2 x2 x8 x4 x2 MA x1 3 ia x5 Control Box Remote Control Warning Light Wire Conduits Battery Wire Q T b 4 P fd n Le 1 al stopper for closing stopper for opening stopper for opening Normal Range Max Range Please install the openers and stoppers properly according to the operating range of the gate 9 CONCRETE PILLAR Fix the motor support 3 on the pillar Be sure there is at least 15cm between GATE the bottom of the motor support and the ground Minn 15cm Fix the motor
3. V DC output to small PCB PHOTOCELL SENDER PHOTOCELL RECEIVER DC DC GND NC COM NO 12V 24V GND DC DC 12V 24V I I I I I I I I I I I I I I I I I I I I I I I I I I I r I I I I r I I I I I I I I I I I Transformer AC Wiring Inside the control box the wiring should be like the photo on the left kun Auto learning Please proceed with this function before you start to use the kit or otherwise the system might drive the gate improperly E g the gate will not close completely or it can t open to the intended position with some stroke left unused Before this process please be sure that there s not any obstacle within the opening or closing route of the gate To start the auto learning keep pressing Auto button on the PCB until the actuators start to move The learning process is as follow 1 Actuator 2 will close first followed by Actuator 1 Auto Clear 2 After 3 seconds Actuator 1 will open fully and 3 seconds later RF 2 RF 1 Actuator 2 will open fully 3 3 seconds later Actuator 2 will close fully and 3 seconds later Actuator 1 will close fully 4 The system will repeat Point 2 3 once 5 3 seconds later both actuators will open and close together 6 After the auto learning process the system is ready for use Note Ifthe warning light is blinking after the learning process it means the learning process has faile
4. d Please make sure that there s not any obstacle on the way for opening and closing and try to launch the auto learning process again Remote Control Pairing Dual gate and Single gate operation To use the remote control please follow the below steps RF2 Assign a button for dual gate operation 1 Keep pressing RF2 on the PCB until the red LED turns OFF 2 Press a desired button on your remote and you will see the red LED on the PCB starts to blink 3 times and it will stay ON which means the pairing process is done 3 Repeat the above two steps for any other button that you want to have dual gate operation RF1 Assign a button for single gate operation Auto Clear The same steps as the above but press RF1 RF 2 RF 1 Note Each channel RF1 8 RF2 can accommodate up to 8 memory positions Operation with a Remote Control The operation with a remote control is very simple One press on the key will open the gate the next press to stop the next press to close the gate the next press to stop the gate and so on Opening 1 Warning light will blink 2 seconds Then Actuator 1 opens and 3 seconds later Actuator 2 opens 2 If the gate hits an obstacle both actuators will reverse 3 seconds with the warning light blinking slowly until the next command is received Closing 1 Warning light will blink 2 seconds Then Actuator 2 closes and 3 seconds later Actuator 1 closes 2 If the gate hi
5. eset Press and hold Clear key on the PCB and connect the AC power Release Clear key and you ll see the red LED blink 5 times indicating all stored data RF memories 8 auto learning process is removed Quick release 1 Please turn the hexagonal screw on the front side of the motor by the clutch release key in CW direction to release the clutch 2 Turn the output axis for and backward to make sure that the clutch is well released Setting of the Dip Switches The default setting of dip switches The below table shows the approximate current limit values for various dip switch settings The maximum current limit also the worst sensibility could shorten the life span of the actuator Try lower current limits before choosing this one The second highest current limit The minimum current limit If the user selects several switches ON for the safety reason the system will choose automatically the lower limit value switch 4 instead of switch 6 or 8 Specifications Motor Power Input 12V DC Maximum Gate Weight 250KGS 550Lbs x 2 Max Speed Overload Protection Current Detection Protection IP44 Control 110 230V AC 60 50Hz RF Remote 303 175 433 92 MHz w Rolling Codes Approx Weight 2 6Kgs 2012 Moteck Printed in Taiwan The contents of this publication are the copyright of the publisher and may not be copied or even extracted unless prior written
6. s Q O on the motor supports O on the pillars by tightening the 4 pairs of screws and nuts as the figure on the right side 1 Please turn the hexagonal screw on the front side of the motor by the clutch release key in CW direction to release the clutch 2 Turn the output axis for and backward to make sure that the clutch is well released Assemble the links between the gate and the axises of the motors as the figure on the right side Put the plastic covers onto the motors and tighten the screws B on the cover Tighten the gate holder onto the gate Swing the gate for and backwards to check if there s any interference Recover the position of clutch by turning the clutch release key in CCW direction Swing the gate again to check if it s now limited by the gear If the gate can still be swung freely please try to turn the hex screw a little more to the CCW direction A click should be heard Connection Diagram Optional Backup battery To transformer AUTO 12V AC To Backup Batter RF 2 2V DC Dip Switches Cear amp pa RE 1 Color indication for motor wire Black wire for Red wire for saja 12V DC Si itl l jka l Motor2 T 225 Antenna Motor 1 Sac Ground Warning Light P To external dual gate operation To external single gate operation For external LED displa Single gate operation manual button Dual gate operation manual button 12
7. ts an obstacle both actuators will reverse 3 seconds with the warning light blinking slowly until the next command is received Garden Lamp Function The garden lamp if installed will be turned on during the operation and will be turned off two minutes after the operation is finished Remarks Gate operation will be correct only when a successful auto learning process is carried out Photocells Optional During Opening When the photocells beam is cut the system will 1 Ignore and keep opening if Actuator 1 has already started opening or 2 Stop if Actuator 1 hasn t started opening During Closing When the photocells beam is cut the system will stop closing and reverse immediately the both actuators until they reach their fully opened positions Auto close Function When this function is activated with dip switch 1 set to ON position both actuators will start closing 30 or 60 seconds depending on dip switch 2 setting after they reach the fully opened positions Manual Buttons on the PCB 1 O C2 is the manual button for Dual gate operation while O C1 is for Single gate operation 2 Optional handsets or external wall buttons are also available connected to O C1 or 0 C2 8 GND connectors Erase the Registered Remote Controls Press Clear button on the PCB for over 5 seconds and release it You ll see the red LED blink 5 times and all registered remote control memories will be erased R
Download Pdf Manuals
Related Search