User Manual
Contents
1. P 6 www rackmountmart com lt Part 3 gt Keyboard Hotkey Command You can switch the Receiver from Local Host port to RJ 45 port and vice versa through simple key se quences made by the remote console side To send commands to the Receiver you must press the hotkey default is Scroll Lock twice within 2 seconds You will hear a beep sound confirming you are in the hotkey mode If you do not press any key during hotkey mode over 2 seconds the hotkey mode will be terminated and back to normal state The default hotkey is Scroll Lock but you can change hotkey as your application convenience If you prefer to use other hotkey please go to OSD menu and change the default hotkey to the other Example Switch between PC port and ig R J 45 port of the Receiver The table blow lists all the supported hotkey commands Command Function Cc To switch between Local and Remote ports To turn the beep sound on or off Q To activate the Auto Scan function Auto scan Remote S and Local port every 8 seconds repeatedly A For auto adjust video signal of remote port to optimum The company reserves the right to modify product specifications without prior notice and assumes no responsibility for any error which may appear in this publication All brand names logo and registered trademarks are properties of their respective owners Copyright 2013 Synergy Global Technology Inc All rights reserved P 7 www2. rackmountmart com
3. with the equipment ensure that it is rated for the voltage and current labeled on the equipment s electrical ratings label The voltage rating on the cord should be higher than the one listed on the equipment s ratings label Observe all precautions and warnings attached to the equipment m If you don t intend on using the equipment for a long time disconnect it from the power outlet to prevent being damaged by transient over voltage Keep all liquids away from the equipment to minimize the risk of accidental spillage Liquid spilled on to the power supply or on other hardware may cause damage fire or electrical shock Only qualified service personnel should open the chassis Opening it yourself could damage the equipment and invalidate its warranty E If any part of the equipment becomes damaged or stops functioning have it checked by qualified service personnel What the warranty does not cover Any product on which the serial number has been defaced modified or removed E Damage deterioration or malfunction resulting from O Accident misuse neglect fire water lightning or other acts of nature unauthorized product modification or failure to follow instructions supplied with the product Repair or attempted repair by anyone not authorized by us Any damage of the product due to shipment Removal or installation of the product Causes external to the product such as electric power fluctuation or failur
4. ackage Contents 1 2 Transmitter 1 3 Receiver lt Part 2 gt Application 2 1 Extending the KVM console port to 150 meters 2 2 Extending the computer to KVM port to 150 meters 2 3 Extending the computer up to 150 meters lt Part 3 gt Keyboard Hotkey Command P 1 P 2 P 3 P 4 P 5 P 6 P 7 www rackmountmart com Before Installation E It is very important to mount the equipment in a suitable cabinet or on a stable surface Make sure the place has a good ventilation is out of direct sunlight away from sources of excessive dust dirt heat water moisture and vibration Unpacking The equipment comes with the standard parts shown in package content Check and make sure they are included and in good condition If anything is missing or damaged contact the supplier immediately lt Part 1 gt lt 1 1 gt Package Contents Receiver LCDK1041 Receiver and Transmitter X 1 LCDK1041 6ft Combo KVM cable X 1 Power adapter w power cord for receiver X 1 Transmitter P 1 www rackmountmart com lt 1 2 gt Transmitter Local Computer VGA Remote I O Power Rear E E gt KB Mouse Power Status USB LED LED LED Status Description Power Solid Red Power is on from the local computer or power adapter No Light There is no Power Status Solid Blue The connection to Receiver is active Flashing Blue Transmitter is sending or receiving data No Light No connection established Transmitter Specif
5. e Use of supplies or parts not meeting our specifications Normal wear and tear Any other causes which does not relate to a product defect m Removal installation and set up service charges OOOOO00O Regulatory Notices Federal Communications Commission FCC This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation Any changes or modifications made to this equipment may void the user s authority to operate this equipment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Re position or relocate the receiving antenna m Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected www rackmountmart com Contents lt Part 1 gt LCDK1041 1 1 P
6. erature 20 60 C Humidity 0 80 Non Condensing Dimension 157 8 x 70 x 30 6 mm Weight 370g P 3 www rackmountmart com lt Part 2 gt Application lt 2 1 gt Extending the KVM console port to 150 meters B USB Conso KVM switch TTTTTTT T LCD A3001 combo A KVM cable j fj Transmitter Transmitter ESER gt Rear Cat6 cable up to 150 meters Monitor LCD A3001 6ft combo KVM cable P 4 www rackmountmart com lt 2 2 gt Extending the computer to KVM port to 150 meters Cat6 KVM port Cat5 6 dongle USB seeeeaa esesssee 1p ye Ezdi Ezi Receiver Front Cat6 cable up to 150 meters Monitor a LCD A3001 6ft combo KVM cable Transmitter Rear A P 5 www rackmountmart com lt 2 3 gt Extending the computer up to 150 meters Monitor fi f LCD A3001 6ft combo KVM cable YA i E1 Transmitter zz e Cat6 cable up to 150m E Receiver E3 EZ LCD A3001 6ft combo KVM cable
7. ication 1 x DB 15 VGA up to 1600 x 1200 Console Pon 2 x USB connector for KB amp mouse Remote I O 1 x RJ 45 connect the receiver up to 150 meters via Cat5 6 cable Local computer 1 x DB 15 combo KVM port LED Power red amp Status blue Power From attached local computer or optional 12V power adapter Operation Temperature 0 50 C Storage Temperature 20 60 C Humidity 0 80 Non Condensing Dimension 157 8 x 70 x 30 6 mm Weight 370g P 2 www rackmountmart com lt 1 3 gt Receiver Local Computer VGA Remote I O Power Rear Ed Ej am KB Mouse Local Remote USB Button Button Button Status Description Local Solid Blue Local port is pressed amp connected to the local PC Blinking Blue Local port is pressed amp no PC signal is detected No Light The local port is not selected or the power is off Remote Solid Blue Remote port is pressed amp connected to the Transmitter Rapid Flashing Blue Remote port is pressed amp auto adjusting the signal Moderate Flashing Blue Remote port is pressed amp no connection established No Light Remote port is not selected or the power is off Receiver Specification 1 x DB 15 VGA up to 1600 x 1200 console Rott 2 x USB connector for KB amp mouse Remote I O 1 x RJ 45 connect the receiver up to 150 meters via Cat5 6 cable Local computer 1 x DB 15 combo KVM port Button Local amp Remote blue Power 12V power adapter Operation Temperature 0 50 C Storage Temp
8. nera Global Technology Inc ee www RackmountMart com Toll Free 1 888 865 6888 Tel 510 226 8368 Fax 510 226 8968 Email sales RackmountMart com User Manual LCDK1041 Combo KVM Extender Legal Information First English printing October 2002 Information in this document has been carefully checked for accuracy however no guarantee is given to the correctness of the contents The information in this document is subject to change without notice We are not liable for any injury or loss that results from the use of this equipment Safety Instructions Please read all of these instructions carefully before you use the device Save this manual for future reference m Unplug equipment before cleaning Don t use liquid or spray detergent use a moist cloth Keep equipment away from excessive humidity and heat Preferably keep it in an air conditioned environment with temperatures not exceeding 40 Celsius 104 Fahrenheit m When installing place the equipment on a sturdy level surface to prevent it from accidentally falling and causing damage to other equipment or injury to persons nearby E When the equipment is in an open position do not cover block or in any way obstruct the gap between it and the power supply Proper air convection is necessary to keep it from overheating E Arrange the equipment s power cord in such a way that others won t trip or fall over it m If you are using a power cord that didn t ship
Download Pdf Manuals
Related Search