Model FMC3
Contents
1. Step 2 Mounting the Wall Plate to the Wall Model FMC3 Brick Solid Concrete Mounting Ik Use the wall plate a as a template to mark 6 hole locations on the wall Three in the top row of slots 3 in the bottom row Make q O gre Assembly Instructions sure these holes are level and there is at least 6 150mm distance between any two holes Pre drill these holes with a 3 8 10mm masonry bit to at least 3 75mm in depth Insert a concrete anchor x into each of these holes Make sure the anchor is seated completely flush with the concrete surface even if there is a layer of drywall or other material in front Attach the wall plate to the wall using 6 lag bolts v and 6 lag bolt washers w shown in Diagram 2A Wood Stud Mounting The wall plate a must be mounted to two wood studs atleast 16 406mm apart Use a stud finder to locate two adjacent studs It is a good idea to verify where the studs are located with an awl or thin nail shown in Diagram 2B Pre drill a 3 75mm deep hole at the desired height in each stud using a 3 16 5mm drill bit Make sure these holes are in the center region of the studs and level with each other Use the wall plate as a template to mark the location of the second hole in each stud Drill 3 75mm deep holes using a 3 16 5mm drill bit in the marked locations Attach the wall plate to the wall using the 4 lag bolts v and 4 lag bolt washers w A OCOOCCGCCOCCCOCC2. OCE f Diagram 2A Diagram 2B CAUTION The maximum loading weight is 80 Ibs 36 kg This wall mount is intended for use only with the maximum weights indicated Use with products heavier than the maximum weights indicated may result in instability causing possible injury TV Size 32 inch to 50 inch See apparatus instructions Thank you for choosing Kanto AV Systems flat panel wall mount The FMC3 is designed to mount flat panel televisions weighing 80 lbs 36 kg or less see Caution above This mount will tilt your TV 15 and swivel pan left and right without the use of tools You can also fine Attaching the Monitor to the Wall Plate tune the horizontal by rotating the mount 2 after the mount it is fixed to the wall Warning Some TVs may require two people to lift We are not responsible for personal injury or product damage Read these instructions fully before installation of this mount If you do not understand these directions or Hook the monitor brackets b c over the top of the wall plate a then lower the monitor brackets to clasp the bottom of the wall have any doubts about the safety of the installation please consult a qualified installation contractor to install plate as shown in Diagram 3A Use a screw driver to tighten the safety bolts The monitor bracket will sit behind the bottom tab hi on the wall plate as shown in Diagram 3B this mount l a i a Make sure there are no defective or missing parts Do not us
3. asher will be needed between the monitor bracket and the spacer Please make sure the monitor brackets b c are vertically centered and level with each other M4 Diameter Bolt M6 Diameter Bolt
4. e defective parts If you are uncertain if the part is defective call Kanto AV Systems directly at 1 888 848 2643 Kanto AV Systems can not be liable for property Diagram 3A Diagram 3B damage or injury caused by incorrect mounting incorrect assembly lifting or incorrect use of this product This product should NOT be mounted on steel stud walls or cinder block walls Consult a qualified installation contractor if you are unsure about the type of wall you may have We make every effort to assure all necessary hardware is included If there is hardware missing please call Kanto AV Systems directly at 1 888 848 2643 Required Tools 3 16 wood drill bit 3 8 masonry bit for brick or concrete installations wrench socket set or Phillips screwdriver CAUTION The wall you plan to use to affix the Kanto mount to must be able to support more than 5 times the weight of the television and the wall mount combined Do not use this product for any purpose other than to mount a flat panel TV on a vertical surface as outlined in this manual Improper installation may cause damage to your TV or serious injury This product should NOT be mounted on steel stud walls or old or cinder block walls Consult a qualified installation contractor if you are unsure about the type of wall you may have TM 4 KAA system Supporting your digital lifestyle Richmond British Columbia Toll Free 1 888 848 2643 www kantoav com sales kantoav com Note The mo
5. unting components and hardware supplied in this package are not designed for walls with steel studs or to cinder block walls If the hardware you need for installation is not included please consult your local hardware store for proper mounting hardware for the application 1 Wall Plate a 1 Left Monitor Bracket b 1 Right Monitor Bracket c 4 M4x12 Bolt e 4 M5x12 Bolt f Cece K KVE VE 4 M4x30 Bolt i 4 M5x30 Bolt j 4 M6x35 Bolt k 4 M8x40 Bolt l 4 M4 Lock Washer m 4 M5 Lock Washer n 4 M6 Lock Washer o 4 M8 Lock Washer p 4 M4 M5 Space q 4 M6 M8 Space r 8 M4 M5 Washer s 4 M6 M8 Washer t 6 M8x90 Lag Bolt v 6 Lag Bolt Washer w 6 M10x80 Concrete Anchor x Step 1A Mounting the Monitor Bracket to a TV with Flat Back To start make sure the bolt diameter e f g h fits your TV Once you have determined the correct diameter see relative diagram below Thread the bolt into the TV using the correct lock washer m n o p and washer s t Please make sure the monitor brackets b c are vertically centered and level with each other M4 Diameter Bolt M6 Diameter Bolt Step 1B Mounting the Monitor Bracket to a TV with Curved Back To start make sure the bolt diameter i j k fits your TV Once you have determined the correct diameter see relative diagram below Thread the bolt into the TV using the correct lock washer m n o p and washer s t For the M4 and M5 diameter bolts another M4 M5 w
Download Pdf Manuals
Related Search