Hawk CTP User Manual(1)
Contents
1. grire TRAIN BETTER Y Industries REPEAT k Combatives Training Partner CTP User Manual Haw WARNING This product is used in HIGH RISK activities Read all of the enclosed information in this User Manual before using or allowing the use of this product If you do not agree with the Terms and Conditions contained in this User Manual you may return the unused product within 14 days from the date of original purchase TERMS AND CONDITIONS PLEASE REVIEW THE FOLLOWING TERMS AND CONDITIONS CAREFULLY THESE TERMS AND CONDITIONS INCLUDE LIMITED WARRANTIES DISCLAIMERS OF LIABILITY AND ARBITRATION PROVISIONS KEEPING USING OR ALLOWING USE OF YOUR HAWK CTP PRODUCT INDICATES YOUR AGREEMENT TO THESE TERMS IF YOU DO NOT WISH TO AGREE TO THESE TERMS YOU MUST RETURN YOUR UNUSED PRODUCT WITHIN 14 DAYS FROM THE DATE OF PURCHASE Definitions Virtic as used herein means Virtic Industries LLC and any and all of its affiliates and or subsidiaries and or business agents and or employees Hawk CTP as used herein means the Hawk Combatives Training Partner CTP product manufactured by or on behalf of Virtic Industries LLC USE WARNING Use of your Hawk CTP is intended only for training under expert supervision for demonstration of technique or for display Use or misuse of your Hawk CTP involves serious risks including injury disability and death Purchasers users and participants assume all risk of injury Virtic cannot and will no2. Cam Strap 3 Footman s Loop 4 2X 1 4 20 x 1 LG Socket Head Fy a Footman s Loop Cap Screws A 5 Belly Cam Str ap iiia Hawk CTP Torso 6 Upper back anchor Assembly 7 Top Cam Strap ll Waterbase Heavy 8 Carabiner Bag 9 Cam Strap Guide Cap Instructions 1 Insert the upper back standoff assembly into the center receiving socket on the rear of the Hawk CTP Torso between the shoulder blades Tighten the captive fastener with 7 32 hex key 2 Install the footmans loop into the 2 lower central mounting points located on the CTP Spine make Figure using the 1 4 20 1 Lg fasteners and the 3 16 hex key 3 Thread the top cam strap through the ring of the upper back anchor then through the slats of the cam strap guide cap and then back through the cam buckle to make a loop of the desired length typically 3 4ft flat loop 4 Snap the carabiner to the far end of the top strap loop 5 Thread the belly cam strap through the footmans loop on the bottom of the CTP Spine 6 Loop the remainder of the strap around the heavy bag and secure with the cam buckle 7 Pull the top cam strap over the top of the standing bag and center the guide cap on top of the central column of the bag Then snap the carabiner onto the belly strap connecting the top and belly straps 8 Tighten the top strap to adjust the height of the CTP Tighten the Belly strap to keep the CTP from shifting side to side on the bag 2014 2015 Virtic Indust
3. Loop 12 Attach the Carabiner of this lower mount cord to the bottom floor anchor point 13 Tighten loosen each Cam Strap to adjust the height of the Hawk and set the system tension 14 Securely wrap any excess strap length to keep it out of the way during training Do not cut the excess strap as you may want to adjust the Hawk CTP height placement in the future 2014 2015 Virtic Industries LLC Page 16 of 16
4. are minors read understand and agree to these Terms and Conditions of Use b you believe they or their guardian understand that they are participating in a high risk activity and assume the risk of death or other personal injury and c you agree to indemnify defend and hold Virtic harmless from any claims made by them arising from their use of Virtic products Limitation of Liability As set forth above under the limited warranty provisions Virtic s liability is limited to repair or replacement of its products which are returned to it prepaid in the specified period of time In no event shall Virtic s lability exceed the value of the products sold Virtic shall not be liable for any special or consequential damages that result from the use of any product sold through this website or otherwise Applicable law may not allow the limitation or exclusion of liability of special or consequential damages so the above limitation or exclusion may not apply to your purchase but it is intended to be the maximum limitation as permitted by law Applicable Law and Arbitration of Disputes Your order from this website shall be governed in all respects by the laws of the State of Pennsylvania U S A without its choice of law provisions and not by the 1980 U N Convention on contracts for the international sale of goods You agree that jurisdiction and venue in any proceeding directly or indirectly arising out of or relating to the purchase of goods from Virtic
5. for purchasing this Hawk Combatives Training Partner We at Virtic Industries take the utmost care in the design manufacture and support of all of our products If you have any questions or need assistance please contact us at www VirticIndustries com For the best training experience please adhere to the following care and usage guidelines Exposure to Weather The Hawk CTP may be used outdoors but it is NOT to be exposed to sunlight for prolonged periods It should NOT be exposed to rain or otherwise soaked in water Cleaning The Hawk CTP skin may be cleaned with common household cleaners applied with a sponge or soft cloth DO NOT use abrasive scrubbing pads General Repair Various spare parts are available for the repair and maintenance of your Hawk CTP unit Please visit www VirticIndustries com product category replacementrepair items for a complete list of spare parts If you cannot find the item that you are looking for or require further assistance please email us at Customer Service VirticIndustries com Skin Repair A Patch Kit is available for the repair of rips or tears in the Hawk CTP skin surface The kit includes a specially formulated two part mixture in segregated containers to be mixed in equal parts and applied to the damaged area The Hawk CTP may be used just a few hours after application and the mixture reaches full strength after several days Usage Guidelines e NEVER STRIKE THE UNDERSIDE OF THE HAWK CTP
6. 5 Virtic Industries LLC Page 8 of 16 USAGE INSTRUCTIONS PITCH AXIS RESISTANCE ADJUSTMENT Tools Needed 3 16 hex key Phillips Head Screwdriver Step 1 Use screwdriver to remove shoulder cover and binding posts Step 2 Use hex key to loosen the locking screw Step 3 Use hex key to tighten tension screws to desired resistance Removing Shoulder Cover Step 4 Use hex key to tighten locking screw Step 5 Use screwdriver to reinstall shoulder cover and binding posts Tension Screw Locking Screw Tension Screw Internal Shoulder Features Close Up 2014 2015 Virtic Industries LLC Page 9 of 16 USAGE INSTRUCTIONS LEG ATTACHMENT Connecting Legs to Torso Attaching Legs to Torso Tools Needed 3 16 hex key Parts List 1 Hawk CTP Torso 2 Hawk CTP Legs 3 6X 1 4 20 x 1 5 LG Socket Head Cap Screws Step 1 Install cap screws through hip attachment plate in the legs into the holes in the torso spine plate as shown 2014 2015 Virtic Industries LLC Page 10 of 16 USAGE INSTRUCTIONS HIP JOINT Adjusting Tension Screw Setting Hip Position Adjusting the Tension and Position of the Hip Joints Step 1 Insert 5 16 hex key into joint as shown and adjust the tension screw as desired Turning the screw clockwise will increase the joint s resistance to motion Turning the screw counter clockwise will decrease the joint s resistance to motion Step 2 Once the desired resistance is achie
7. HOR POINTS IS CRITICAL TO THE SAFE OPERATION OF THE MOUNTING SYSTEM AN IMPROPERLY SECURED ANCHOR POINT COULD RESULT IN SERIOUS INJURY OR DEATH BE CERTAIN THAT THE ANCHORS ARE SECURELY FASTENED TO A STRUCTURE THAT CAN SUPPORT THE STRESSES GENERATED DURING TRAINING VIRTIC INDUSTRIES IS NOT RESPONSIBLE FOR IMPROPER OR UNSAFE INSTALLATION OF THE SYSTEM 5 Use a 3 16 hex key to attach the Bungee Mount Plate to the lower spine plate on the Hawk CTP Torso with four 1 4 20 x 1 fasteners 6 Use a 7 32 hex key to attach Strap Handles to the outer receptacles on the Hawk CTP Torso s rear shoulder blades 7 Attach one 1 Caribiner to each Bungee Loop To increase the strength and speed of Hawk CTP oscillation during training Virtic Industries recommends that the bungee loops be doubled over to form two 2 rings of bungee 8 Thread one 1 Cam Strap through the left Strap Handle on shoulder and through one 1 Bungee Loop both rings if the bungee is doubled over 9 Thread one 1 Cam Strap through the right Strap Handle on shoulder and through one 1 Bungee Loop both rings if the bungee is doubled over 10 Attach the Carabiner at the end of each Bungee Loop to the appropriate overhead anchor point Tighten loosen the Cam Straps to raise lower the Hawk CTP to the approximate desired height 11 Thread the remaining Cam Strap through the Breakable Shackle attached to the bungee mount plate and through the third remaining Bungee
8. MALL CLAIMS COURT OF DELAWARE COUNTY PENNSYLVANIA Your rights will be determined by a NEUTRAL ARBITRATOR and NOT a judge or jury You are entitled to a FAIR HEARING BUT the arbitration procedures are SIMPLER AND MORE LIMITED THAN RULES APPLICABLE IN COURT Arbitrator decisions are as enforceable as any court order and are subject to VERY LIMITED REVIEW BY A COURT FOR MORE DETAILS SEE APPLICABLE LAW AND ARBITRATION ABOVE One Year Limited Warranty Virtic warrants this Hawk CTP to be free from defects in materials and workmanship for a period of one 1 year from the date of original purchase provided it has not been subjected to obvious abuse neglect or misuse The limited warranty is not transferable and is available only for the original purchaser of this Hawk CTP Virtic s sole liability is limited to repairing or replacing this Hawk CTP returned prepaid to Virtic within this one year period All warranty coverage extends only to the original purchaser from the date of purchase Virtic s obligation under this Warranty is limited to replacing or repairing at Virtic s option the product at an authorized service center Any product for which a warranty claim is made must be received by Virtic at an authorized service center and accompanied by sufficient proof of purchase e g sales invoice indicating date of purchase All freight and handling fees are the responsibility of the consumer to pay both to and from Virtic All warranty claims must
9. TO THE JOINT MECHANISM ALWAYS SET THE ARMS IN FRICTION SLIDE MODE WHEN DOING GROUND WORK WITH THE UNIT Selecting a new arm position in locked position mode Step 1 Insert 5 16 hex key into shoulder socket such that the key seats into the internal screw Step 2 Turn the screw counter clockwise until the pitch axis enters friction slide mode Step 3 Adjust the pitch axis to the new desired position Step 4 Turning the screw clockwise all the way will lock the arm in its current position It may be necessary to move the arm slightly to allow internal features to align It should not require effort to turn screw Resistance indicates that the internal features are not correctly aligned Selecting a new arm position in friction slide mode Step 1 Pull the arm firmly to the new desired position The arm will resist up to a point then slide smoothly to the new desired position 2014 2015 Virtic Industries LLC Page 5 of 16 USAGE INSTRUCTIONS ARM POSITION ADJUSTMENT CONT Shoulder Joint Roll Axis An ka a Lr T k an i a I s 9 2 Adjusting Locking Screw Adjusting Roll Axis Position The shoulder roll axis allows you to rotate the arm about its longitudinal axis as shown in the above drawing The roll axis is controlled by an internal clutch that can operate in 2 modes Friction Slide or Locked Position Steps select the operating mode of the roll axis Step 1 Insert 5 16 hex key into should
10. TORSO OR ITS REAR MOUNTING PLATE SERIOUS INJURY MAY RESULT Do not strike the Hawk CTP with pointed or sharp objects as they may damage the product e Hawk is designed for use in various mounting configurations as well as a standalone training partner If using Hawk while it is not attached to a mounting system be sure to remove any and all hardware components used for such mounting in order to avoid injury or damage to floor surfaces or training mats e Always use protective gear e g gloves when striking the Hawk CTP to avoid injuries e The skin surface may feel grippy under humid conditions The friction may be reduced by applying baby powder over all of the Hawk CTP skin surface 2014 2015 Virtic Industries LLC Page 3 of 16 USAGE INSTRUCTIONS ARM POSITION ADJUSTMENT The Hawk CTP enables striking and grappling drills with more realism than ever before as the combatant must account for their opponents guards during training Hawk s arms may be posed in a number of positions to simulate various combative scenarios In one operating mode once a ready position is set the arms will recover that position regardless of how they are disturbed during a training exercise In a second operating mode the arms will assume a new position when dislocated from the original setting Both right and left arms have the same control features as described below Shoulder Joint Pitch Axis Adjusting Locking Screw Adjusting Pitch Ax
11. be pre authorized by Virtic Pre authorization can be obtained by e mailing customer service virticindustries com This warranty does not extend to any product or damage to a product caused by or attributable to freight damage abuse misuse improper or abnormal usage or repairs not provided by a Virtic authorized service center or for products used for rental purposes This warranty does not cover ordinary wear and tear weathering failure to follow directions improper installation improper maintenance or acts of Nature Weather damage damage caused by unauthorized repair work or damage caused by improper used of the products are not covered by the product warranty WARRANTY DISCLAIMER THE ABOVE STATED WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND OF ALL OTHER OBLIGATIONS AND LIABILITIES OF VIRTIC VIRTIC NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF ITS PRODUCTS THE ABOVE LIMITED WARRANTIES SHALL NOT APPLY TO ANY PRODUCT WHICH HAS BEEN SUBJECT TO ACCIDENT NEGLIGENCE ALTERATION ABUSE OR MISUSE THE TERM ORIGINAL PURCHASER AS USED IN THIS WARRANTY MEANS THE PERSON TO WHOM THE PRODUCT IS ORIGINALLY SOLD AS SHOWN ON THE SALES INVOICE THESE WARRANTIES SHALL APPLY ONLY WITHIN THE BOUNDARIES OF THE UNITED STATES AND CANADA GENERAL CARE AND USE INSTRUCTIONS Thank you
12. er socket such that the key seats into the internal screw Step 2 Turn the hex key to adjust internal screw it s position determines the operating mode of the roll axis as described below Turning the screw clockwise all the way will lock the arm in its current position It may be necessary to move the arm slightly to allow internal features to align The screw should turn without much effort resistance indicates that the internal features are not correctly aligned Turning the screw counter clockwise from the locked position will engage friction slide 2014 2015 Virtic Industries LLC Page 6 of 16 mode It will take several turns of the screw to maximally engage this mode Turning too far will unlock both stages of the clutch and the arm will turn freely If this happens simply turn the screw clockwise until the clutch reengages e For most uses the friction slide mode will be preferred When wrestling grappling or drilling in other ground work always set the arms in friction slide mode WARNING WRESTLING OR GRAPPLING WITH THE UNIT WHEN AN ARM IS LOCKED IN POSITION CAN RESULT IN INTERNAL DAMAGE TO THE JOINT MECHANISM ALWAYS SET THE ARMS IN FRICTION SLIDE MODE WHEN DOING GROUND WORK WITH THE UNIT Selecting a new arm position in locked position mode Step 1 Insert 5 16 hex key into shoulder socket such that the key seats into the internal screw Step 2 Turn the screw counter clockwise until the roll axis enters frict
13. ion slide mode Step 3 Adjust the roll axis to the new desired position Step 4 Turning the screw clockwise all the way will lock the arm in its current position It may be necessary to move the arm slightly to allow internal features to align It should not require effort to turn the screw Resistance indicates that the internal features are not correctly aligned Selecting a new arm position in friction slide mode Step 1 Pull the arm firmly to the new desired position The arm will resist up to a point then move incrementally to the new desired position 2014 2015 Virtic Industries LLC Page 7 of 16 USAGE INSTRUCTIONS ARM POSITION ADJUSTMENT CONT Elbow Joint The elbow joint of the Hawk CTP can be locked into position by use of the bungee loop that extends from the lower tricep to the upper forearm Reducing Elbow Angle Locking Elbow Increasing Elbow Angle Unlocking Elbow Reducing the Elbow Angle Step 1 Move the forearm to the desired angle Pull the bungee cord exiting from the tricep area until taught Step 2 Apply tension to the cord from the tricep area down toward the elbow then sharply pull the wrist to straighten the arm The bungee will catch in the internal grip feature Releasing the Elbow Bungee Tension Step 1 Apply tension to the bungee exiting the tricep area and pull the bungee toward the shoulder This should pull it free of the internal grip feature and allow the elbow to move freely 2014 201
14. is Position The shoulder pitch axis allows you to raise and lower the arm as shown in the above drawing The pitch axis is controlled by an internal clutch that can operate in 2 modes Friction Slide or Locked Position Steps select the operating mode of the pitch axis Step 1 Insert 5 16 hex key into shoulder socket such that the key seats into the internal screw Step 2 Turn the hex key to adjust internal screw it s position determines the operating mode of the pitch axis as described below Turning the screw clockwise all the way will lock the arm in its current position It may be necessary to move the arm slightly to allow internal features to align The screw should turn without much effort resistance indicates that the internal features are not correctly aligned 2014 2015 Virtic Industries LLC Page 4 of 16 Turning the screw counter clockwise from the locked position will engage friction slide mode It will take several turns of the screw to maximally engage this mode Turning too far will unlock both stages of the clutch and the arm will hang at the sides of the unit If this happens simply turn the screw clockwise until the clutch reengages For most uses the friction slide mode will be preferred When wrestling grappling or drilling in other ground work always set the arms in friction slide mode WARNING WRESTLING OR GRAPPLING WITH THE UNIT WHEN AN ARM IS LOCKED IN POSITION CAN RESULT IN INTERNAL DAMAGE
15. not exceeding 12 000 00 will be in the Magisterial District Court of Delaware County Pennsylvania You agree that any dispute or controversy arising out of or relating to the purchase of goods from Virtic exceeding 12 000 00 shall be resolved exclusively and finally by arbitration subject to the provisions of the Uniform Arbitration Act as enacted in Pennsylvania as found in the Pennsylvania statutes at Title 15 Such arbitration shall occur in Delaware County Pennsylvania before a sole arbitrator Any award rendered in any such arbitration proceeding shall be final and binding on each of the parties and judgment may be entered thereon in a court of competent jurisdiction Any cause of action or claim you may have with respect to a Virtic Product or any other claim related to the use of this website must be commenced within one 1 year after the claim or cause of action arises Virtic s failure to enforce strict performance of any provision of these terms and conditions shall not be construed as a waiver of any provision or right Neither the course of conduct nor trade practice shall act to modify any of these terms and conditions NOTICE OF DISPUTE RESOLUTION AND ARBITRATION AGREEMENT The terms and conditions of all sales by VIRTIC provide that all disputes between you and VIRTIC will be resolved by BINDING ARBITRATION You GIVE UP YOUR RIGHT TO GO TO COURT to assert or defend your rights under this contract except for matters that may be taken to THE S
16. p p pr y TA re asteners 9 Upper back anchor Assembly Ri Nw sis ies Hee te A Adil Belly Cam Strap Lop Cam Strap So hi 11 Carabiner iB fl Hawk CTP Torso Instructions l S o Se E Insert the upper back standoff assembly into the center receiving socket on the rear of the Hawk CTP Torso between the shoulder blades Tighten the captive fastener with 7 32 hex key Install the footmans loop into the 2 lower central mounting points located on the CTP Spine make Figure using the 1 4 20 1 Lg fasteners and the 3 16 hex key Thread the top cam strap through the ring of the upper back anchor and then back through the buckle of the cam strap to make a loop of the desired length typically 1 5 2ft flat loop Snap the carabiner to one of the support straps chains on the heavy bag Thread the belly cam strap through the footmans loop on the bottom of the CTP Spine Loop the remainder of the strap around the heavy bag and secure with the cam buckle Adjust the top strap to achieve the desired height of the CTP Tighten the belly strap to keep the CTP from shifting on the heavy bag 2014 2015 Virtic Industries LLC Page 13 of 16 Tools Needed 7 32 hex key 3 16 hex key STANDING BAG MOUNT INSTALLATION INSTRUCTIONS Top Cam Strap Cam Strap Guide Cap Strap Anchor i Assembly Parts List T t i Ti e i e Carabiner 1 Hawk CTP Torso ewe bf i i 2 Standing Heavy bag IA az i Belly
17. ries LLC Page 14 of 16 BUNGEE MOUNT INSTALLATION INSTRUCTIONS Tie Down Anchor M Tools Needed Carabiner g S 7 32 hex key Bungee Loop ss Carabiner Carabiner 1 y M Loop eae Cam Straa Tie Down Anchor 3 16 hex key U Cam Strap Webbing Handle Ia Parts List Moy y Webbing Handle 1 Hawk CTP Torso Bme E P ai 2 3X Tie Down Anchor han wil a Hawk CTP Torso 3 6X Carabiner Ly a Fasteners 4 3X Bungee Loop ry lt 8 Bungee Mount 5 3X Cam Strap i Bice 6 2X Webbing Handle with ds Breakable Shackle captive fasteners Cam Strap 7 Bungee Mount Plate w i Breakable Shackle A _ _ __ Bungee Loop 8 4X 1 4 20 x 1 LG fasteners KO Carabiner ST Tie Down Anchor Instructions 1 Select installation location considering the following minimum spatial requirements o At least two 2 feet clearance behind Hawk CTP from nearest wall to rear o At least one 1 foot clearance on either side of Hawk CTP from nearest wall to each shoulder Additional clearance may be needed to comfortably move all around the Hawk CTP while training o Six 6 feet clearance in front of Hawk CTP is recommended to maintain proper distance and footwork during training Less space may be suitable at user discretion o The mount is designed to attach to overhead support points ranging from six 6 feet to ten 10 feet high Higher overhead support points may require strap extension
18. s 2 Choose two 2 overhead support points spaced at least sixteen 16 inches apart note that floor joists are typically spaced 16 apart on center The width of the overhead support spacing will affect how the Hawk CTP responds during training At the 16 minimum spacing the Hawk CTP will exhibit considerable rotation about its centerline With a wider overhead spacing 48 or more the Hawk CTP will tend to oscillate back and forth and rotation will be significantly curtailed In other words with narrower overhead spacing the Hawk CTP will tend to swing his arms as if it were throwing hooks and with wider overhead spacing the Hawk CTP will tend to throw hammer fists and jabs 2014 2015 Virtic Industries LLC Page 15 of 16 BUNGEE MOUNT INSTALLATION INSTRUCTIONS CONT 3 Choose one 1 floor support point laterally located mid way between the two overhead support points Moving the lower support point forward or backward relative to the ceiling support points affects the forward lean of the Hawk CTP To increase the forward lean place the floor mounting point further back relative to the overhead mounting points 4 Attach one 1 tie down anchor if required at each of the 3 support points Use 1 4 diameter screws or bolts not included to securely fasten the anchors to the selected support locations The type of fastener used will be dictated by the installation location WARNING THE PROPER INSTALLATION OF THE ANC
19. t be responsible for the misuse or unauthorized and improper use of your Hawk CTP High Risk Activity The Hawk CTP is used in high risk activities such as military law enforcement security self defense contact combat sports and general fitness training Your participation in any of these activities and or use of the Hawk CTP is at your own risk You agree to consult with a licensed physician before participating in any of these high risk activities You also agree to read and follow specific warnings and instructions provided with your Hawk CTP or associated product literature Assumption of the Risk By buying using providing or allowing the use of your Hawk CTP you understand and agree that training and physical fitness activities are High Risk Activities and to the extent permitted by law YOU EXPRESSLY AND VOLUNTARILY ASSUME THE RISK OF DEATH OR OTHER PERSONAL INJURY SUSTAINED WHILE PARTICIPATING IN SUCH ACTIVITIES WHETHER OR NOT CAUSED BY THE NEGLIGENCE OR OTHER FAULT of Virtic including but not limited to equipment malfunction from whatever cause or any other fault of Virtic Additionally you agree to indemnify defend and hold Virtic harmless from any third party claims arising from such High Risk Activities or use of any Virtic Product Duty of Coaches Trainers Gyms to inform others of these Terms and Conditions Before you allow others to use your Hawk CTP you agree that a you will require that they or their legal guardian if they
20. ved simply push or pull on the legs to move the joint to the desired position Since the joints have built in resilient behavior it will be necessary to move the joint slightly past the desired position and allow it to spring back to the desired position 2014 2015 Virtic Industries LLC Page 11 of 16 USAGE INSTRUCTIONS KNEE JOINTS Adjusting Upper Knee Joint Tension Screw Setting Knee Position 2014 2015 Virtic Industries LLC Step 1 Step 2 Adjusting Lower Knee Joint Tension Screw Insert 5 16 hex key into joints as shown and adjust the tension screws as desired Turning the screw clockwise will increase the joints resistance to motion Turning the screws counter clockwise will decrease the joints resistance to motion Once the desired resistance is achieved simply push or pull on the legs to move the joints to the desired position Since the joints have built in resilient behavior it will be necessary to move the joints slightly past the desired position and allow them to spring back to the desired positon Page 12 of 16 Tools Needed 7 32 hex key 3 16 hex key HANGING BAG MOUNT INSTALLATION INSTRUCTIONS Heavy Bag Hanging Straps by pi o Carabiner Parts List Top Cam Strap 4 Hawk CTP Torso e 5 Heavy bag w aa Heavy Bag 6 Footmans Loop ie i Upper Back Anchor 7 2X 1 4 20 x 1 LG Socket ZOT EN Assembly io o EAS Head Cap Screws Syme Footman s Loop and 8 Belly Cam Stra
Download Pdf Manuals
Related Search