User Manual
Contents
1. from battery 4 Insert charger lead into socket on battery casing 6 There are two indicator lights on the charger as follows POWER Glows red when mains power connected amp turned on CHARGE Glows red when charging amp green when charge is complete 7 When battery is charged firstly turn off the mains supply unplug then remove the charging plug from the battery 8 Insert bicycle power lead into battery amp push retaining clip over plug If your BATRIBIKE Buzz is not in use for an extended period charge the battery once a month to prevent deterioration Quick release fittings for seat amp handle bar height adjustment With the locking lever in the loose position tighten the nut until finger tight The final tightening is done by moving the lever to the locked position To undo move lever to loose position to enable height adjustment Handlebar folding mechanism To fold down move locking lever to the loose position amp pivot the lever amp bolt forward the handlebars will now fold Handlebars MUST be locked back into position correctly 7 before riding Riding To turn the power on insert the key in the slot on the back of the headlight amp turn 1 click clockwise The red power indicator should now illuminate When you pedal the motor will automatically cut in to assist To use the throttle turn the activate deactivate switch on I position Now when you turn the throttle the bicycle will mo2. BATRIBIKE ELECTRIC BICYCLES User Manual Thank you for purchasing a BATRIBIKE Electric Bicycle from Fallowgate Limited With care and correct usage your bicycle will give many years of service Please read the manual fully before use al Thank you for purchasing a BATRIBIKE Electric Bicycle from Fallowgate Limited put With care and correct usage your bicycle will give many years of service PURCHASE DATE Please read the manual fully before use Service amp Spares Remember to check all nuts and screws before and after the first ride This will need to be repeated after a week or so of riding and periodically to maintain safe use of your BATRIBIKE bicycle Cables may also stretch a little during the first few uses Brakes and gears may need to be adjusted after the first few days to ensure correct operation Refer to your local cycle shop if you are not familiar with this operation Your BATRIBIKE bicycle uses standard cycle parts wherever possible Items such as tyres tubes lights brake pads blocks and cables may be obtained from your local cycle shop or retailer Specialist parts such as the motor battery torque sensor or frame components are only available from Fallowgate Limited or their authorised distributors BOX CONTENTS 1 PART ASSEMBLED BICYCLE 1 FRONT WHEEL 1 SADDLE amp POST 1 BATTERY CHARGER 1 PAIR PEDALS 1 SMALL BOX CONTAINING 1 BATTERY CHARGER 2 SPANNERS CA
3. UTION 3 Your new BATRIBIKE Buzz needs assembling by a competent person If you are in any doubt about assembly you should contact a local cycle shop for assistance Your BATRIBIKE Buzz is heavy and should not be lifted by one person Assembly Instructions 1 Remove straps from the box open top amp cut down the front sides as indicated Fold the front of the box down amp use this to protect the bottom of the front forks until the wheel is inserted Unlock amp remove battery if fitted battery may come in a separate parcel The keys are located on the front fork tube Put battery on charge see user instructions on page 6 for charging procedure Remove the bicycle from the main body of the box amp stand on the folded down front of the box put the side stand down to prevent the bicycle falling over Cut the tie holding the front wheel amp front mudguard stand the wheel to one side Remove the tie straps holding the handle bar assembly to the frame amp remove packing from the bottom Insert handlebars into tube as shown Slightly tighten bars into the tube using the 6mm hex key supplied The head of the stud is under the folding mechanism as shown Final tightening amp alignment should be carried out after front wheel is inserted 5 Remove packaging from front mudguard amp fit loosely to the holding bracket across the front forks DO NOT TIGHTEN UNTIL WHEEL IS IN PLACE 6 Remove packaging
4. from front brake assembly Remove the nut washer amp 2 spacers from the end of the axle furthest from the brake lever Insert the end of the axle into the wheel centre so that the brake shoes go into the brake drum push the axle through to come out of the other side Place the 2 spacers onto the axle then the washer with the tag facing inwards followed by the nut with the serrated edge inwards Leave the nuts at the outer ends of the axle to make it easier to locate the wheel in the front forks You will need assistance with lifting for this ste 7 Lift up the front forks amp place the axle into the slots on the forks with the brake assembly on the left hand side of the bike making sure the U shaped slot on the brake assembly goes over the locating peg on the left hand fork leg The two spacers should be on the inside of the forks there should be a washer on the outside of the forks on each side with the tag facing inwards Put the tag of each washer into the hole on each fork leg tighten the two nuts to leave equal amounts of thread showing on the axle on both sides Qo 8 Fasten the front mudguard stays to the bottom of the fork legs just behind the axle with the screws provided Lift the mudguard to its highest point in the slot on the top of the fixing bracket amp tighten all three fasteners 9 Align the handlebars at 90 degrees to the front wheel amp tighten stud left loose in instruc
5. re exclusive to Fallowgate Limited Kellaway House er Marton Road Sturton by Stow Fa l OW g A te Lincoln p NR C LIMITED LN1 2AH Phone 01427 787774 E mail support batribike com USER MANUAL BATRIBIKE Buzz ISSUE 2 2009 Fallowgate Limited
6. tion 4 Remove pedals from packaging amp screw into the correct side crank The left hand crank has a left hand thread amp the pedal is marked with an L stamped in the end The left pedal screws anti clockwise amp the right pedal chain side screws in clockwise Tighten both pedals 10 SPEED RESTRICTOR WIRE in certain countries it is illegal to ride on throttle alone at more than 20kmh To de restrict the speed to be able to travel up to 15mph on throttle disconnect the plug amp socket in the white wire located under the battery lock Fasten both ends to the wiring loom to prevent them catching in moving parts J Remove the rest of the packaging 12 Inflate tyres to correct pressure located on tyre wall 13 When charging is complete replace battery amp connect battery cable lock in position 14 Insert seat to desired height amp lock in position NOTE maximum height is marked on seat tube 15 Congratulations you have built your BATRIBIKE Buzz Please read the user instructions for correct use of controls before you ride User Instructions Battery Charging The battery can be either charged on or off the bicycle but must be charged inside in dry conditions to avoid the risk of electrical shock Only use the charger supplied with the bicycle 1 Ensure the power is turned off at the key switch 2 Pull back the cable retaining clip to allow cable to be removed 3 Pull out power plug
7. ve forward under electrical power the further you twist the throttle the more power will be applied amp the faster you will travel Using on full throttle will reduce the range achieved Horn To operate the horn press the red button on the left handlebar Front Light To turn the light on turn the key to the second click the light amp indicator light will illuminate Always turn the power off when not in use Braking To stop release the throttle amp pull the brake levers Side Stand To put the bicycle on its stand 1 While holding the bicycle upright push the stand to its full extent 2 Push spring loaded locking lever into place 3 Lean bicycle over onto stand Make sure bicycle is on solid ground www batribike com BATRIBIKE ELECTRIC BICYCLES Warranty Please retain your receipt as this is your proof of purchase and entitlement to Warranty Your new BATRIBIKE Buzz is guaranteed for 1 year from date of purchase The battery is covered for 6 months as battery life is determined by User care In the event of warranty repairs becoming necessary you should return your bicycle to Batribike at the address below delivery amp collection charges are not redeemable under warranty Brake blocks pads tyres lights and cables etc are considered as consumables and replacements are available from BATRIBIKE or may be obtained from your local cycle shop BATRIBIKE Electric Bicycles a
Download Pdf Manuals
Related Search