User Manual - Slide Kamera
Contents
1. pay special attention to the fact that the arm and counterweight clamping knobs are securly tightened to prevent the telescopic elements of the crane from moving Please remember m It is compulsory that all clamping knobs of the crane are properly placed and secured m Legs of the tripod should be widely spaced to ensure stability of the device v The crane should be tightly attached to the tripod It is not allowed to operate the crane in a way causing danger to the people in the proximity of the device v In case of any impact weight of the crane combined with high inertia of the arm present a hazard to human body and may cause damage of the equipment m Weight of the crane combined with high inertia of the arm in the event of an impact can cause damage to the human body and the equipment itself v Exercise extreme caution while mounting weights on the counterweight arm Falling weight can cause serious injury I Exercise extreme caution during the transport of the crane Any impact can damage the equipment 10 Maintenance The crane does not need any additional service or lubrication of the components Maintainance procedures of Slide Kamera ROAD JIB crane are reduced to keeping the equipment clean Any changes in design and repairs are made only and exclusively by the manufacturer Failure to comply with the recommended guidelines outlined in this manual will result in loss of warranty Slide Kamera ROAD JIB Camera Crane 11 Transp2. plate Once you balance the crane properly tighten the safety nuts Thecounterweight arm is also equipped with a sliding weight used mainly when lens changing that allows to balance the crane without the need of adding additional counterweights Counterweight arm 1 Sliding weight 2 Knob that locks the sliding weight 3 Weights 4 Safety nut 5 Slide Kamera ROAD JIB Camera Crane 6 2 Setting up working arm of the crane In order to set up working arm of the crane properly unlock arm slide clamping knobs three knobs The knobs allow to seta precise length of the working arm Extend the arm of the crane and secure it by locking three clamping knobs There is also a possibility to set the angular position of the crane mounting plate by controlling the extend ofthe crane arms Never unscrew the knobs only loosen PLEASE NOTE Disassemble any photo video equipment from the camera crane mounting plate if you intend to change armlength Failure to do so may result in uncontrolled spreading of the arm and can cause damageto the equipment 7 Mounting equipment on ROAD JIB mounting plate ROAD JIB crane mounting plate is equipped with a mounting groove with 1 4 and 3 8 photographic screws The screws allow to mount photo video equipment in any position on the plate Four M4 holes allow to mount Slide Kamera AKC 3 adapter or Manfrotto MN577 adapter Additionally P there are two rubber plates that protect equipment again
3. User Manual Ultralight 4 5 kg portable and compact camera crane used for cameras and photo cameras of a total weight up to 3 5 kg Its compact size makes it a perfect solution when shooting in most extreme places Slide Kamera ROAD JIB outperforms other camera cranes in terms of stability rigidity and comfort of use Slide Kamera ROAD JIB Camera Crane Pdf version of the manual available for download www slidekamera eu T slidekamera 1 2014 made in ZAF Before you start your work with Slide Kamera ROAD JIB camera crane we strongly recommend to read the manual carefully Please note that using the device in a manner inconsistent with the instructions unauthorized repair attempts or any kind of modification of the device can cause a damage the manufacturer is not responsible for In case of damage during transport you are required to submit m proof of purchase m protective styrofoam inserts fillers included in the set in case of new product delivery If you fail to comply with the abovementioned conditions the manufacturer reserves the right to refuse the complaint Photos of products may slightly differ from the actual product due to constant modifications and improvements introduced by the manufacturer Producent Slide Kamera High Engineering Technology CNC s c Sebastian Pawelec Karol Mikulski Glina 45 82 522 Sadlinki Vat Identification Number 581 188 33 32 Slide Kamera Office 80 175 Gdansk Po
4. a AKC 3 adapter base to HST 2 or HST 3 tripod socket using Manfrotto half ball Mount Slide Kamera AK 101 sliding plate to crane rotational head using Slide Kamera 1 4 and 3 8 photographic screws Unlock AKC 3 adapter clamping levers slide AK 101 sliding plate mounted to ROAD JIB rotational head into AKC 3 adapter base thus connecting Slide Kamera ROAD JIB camera crane with Slide Kamera HST series tripod Remember to lock the clamping levers AK 101 sliding plate 1 AKC 3 adapter base 2 AKC 3 adapter clamping lever 3 Elements of Manfrotto MN577 adapter with MN501PL plate Manfrotto MN577 adapter 1 Manfrotto MN501PL plate 2 Four M4 holes 3 Clamping knob 4 1 4 screw 5 3 8 screw 6 1 4 threaded hole 7 3 8 threaded hole 8 Slide Kamera ROAD JIB Camera Crane 6 Preparing Slide Kamera ROAD JIB crane to work 6 1 Setting up counterweight arm of the crane After mounting ROAD JIB crane on any Slide Kamera HST series tripod set up counterweight arm of the crane In order to do that pull the pin locking the arm and turn it right or left The pin will unlock the arm Set the arm properly and lock the arm again Counterweight arm 1 Pin that locks the counterweight arm 2 After mounting the accessories on the mounting plate of the crane balance the crane by mounting the weights on the arm Please remember that maximum permissible counterweight is 6kg for 4 5kg of payload on the crane mounting
5. efficient and comfortable screw the half ball to the rotational head of the crane place the set on the tripod socket and then attach the handle from the underside of the tripod Slide Kamera tripods come with Slide Kamera HCZ 75mm or 100mm socket Replaceable Slide Kamera HCZ sockets match systems such as Manfrotto Sachtler Miller We are able to provide a socket for any type of video head on client s request 5 2 Mounting ROAD JIB camera crane on Slide Kamera HST series tripod using Slide Kamera AKC 3 adapter or Manfrotto MN577 adapter Slide Kamera AKC 3 adapter or Manfrotto MN577 adapter allows to mount and dismount various accessories used during photo video realisations In this case mounting ROAD JIB crane on Slide Kamera tripod using AKC 3 adapter or Manfrotto MN577 adapter allows to mount and dismount the crane from the tripod in a very fast and easy way Method of mounting both adapters is the same photos below present Slide Kamera AKC 3 adapter in use Elements of Manfrotto MN577 adapter with MN501PL plate are described on the next page In order to mount AKC 3 adapter slide AK 101 sliding plate out of the AKC 3 adapter base Remove all screws except for the 1 4 and 3 8 photographic screws and the grub that locks them Slide Kamera ROAD JIB Camera Crane AKC 3 adapter base 1 AK 101 sliding plate 2 1 4 photographic screw 3 3 8 photographic screw 4 Grub that locks 3 8 and 1 4 screws 5 PO Mount Slide Kamer
6. eight arm length 600mm 1000mm do 1450mm working arm length two 3 8 holes two 1 4 holes 1 4 and 3 8 holes in rotational head Quick Release System four M4 holes in camera crane mounting plate built in camera crane base 3 5kg for 6kg of counterweight aluminium devices equipped with 1 4 hole devices equipped with 3 8 hole four M4x12 screws 4 5kg Sliding weight 0 5kg 2x2kg 1x1kg 1x0 5kg available three knobs on working arm of the crane available available 90 Slide Kamera ROAD JIB Camera Crane 5 Mounting ROAD JIB camera crane on Slide Kamera HST series tripods Slide Kamera ROAD JIB camera crane device is dedicated to Slide Kamera HST series tripods Method of mounting in case of HST 2 and HST 3 tripod is the same ROAD JIB crane can be mounted on the tripod either directly using Manfrotto half ball or indirectly using a proper adapter Slide Kamera AKC 3 or Manfrotto MN5 77 that allow to change the accesories used in photo video productions in a very fast and easy way 5 1 Mounting ROAD JIB camera crane on Slide Kamera HST series tripod using Manfrotto half ball Slide kamera ROAD JIB crane can be mounted directly on HST series tripod with the use of Manfrotto half ball Picture below presents example of mounting ROAD JIB crane on HST 3 tripod Thanks to rotational head built in camera crane base there is no neet to attach addittional rotational head to the crane In order to make mounting more
7. ent Its compact size makes it a perfect solution when shooting in most extreme places Slide Kamera ROAD JIB outperforms other camera cranes in terms of stability rigidity and comfort of use Arm of the crane is made of resistant building profiles that ensure high rigidity and durability of the device Profiles have also anticorrosive protection against weather conditions Additionally the crane is eqipped with various knobs and levers that allow you to lock the arm in any desirable position ROAD JIB crane comes with a rotational head with a locking system build in camera crane base equipped with 1 4 and 3 8 holes Quick Release System 1 4 and 3 8 holes allows to mount and dismount the crane on and from the tripod using Manfrotto 577 or Slide Kamera AKC 3 adapters Mounting of the adapter to the rotational head using both 1 4 and 3 8 screws is the most effective solution and provides high stability of your equipment when you capture a perfect shot All moving parts of the crane are bearinged what ensures extreme smoothness of motion Slide Kamera ROAD JIB Camera Crane Number of mounting holes allowing to attach additional accessories provide great universality of our device Mounting plate of the crane is equipped with 1 4 and 3 8 photographic screws for DLSR photo cameras or light cameras Hole spacing allows to mount Manfrotto 577 adapter or Slide Kamera AKC 3 adapter Steel joint of high durability and resistance to damage allows to
8. land Ul Kartuska 386 tel fax 48 58 710 41 04 e mail biuro slidekamera pl office slidekamera eu www slidekamera com www slidekamera eu Slide Kamera ROAD JIB Camera Crane Table of contents 1 Elemens and construction of Slide Kamera ROAD JIB camera CraNe ccccccseccsessseeeeseteeeessssteescsssssesssssieeesares 3 2 A ddtional ACCE SOO Sacose ea ene a ee Dee ee 5 S POCU EUSE ee E E AA EE 6 aS e CM MOM E AEA O E A N T 8 5 Mounting ROAD JIB camera crane on Slide Kamera HST series tripOdS ccccccscsescsscsesssssseesssetessesesssseseeeees 9 5 1 Mounting ROAD JIB camera crane on Slide Kamera HST series tripod using Manfrotto half ball 9 5 2 Mounting ROAD JIB camera crane on Slide Kamera HST series tripod using Slide Kamera AKC 3 adapter or Manfrotto MNS577 adape cesrsnennnneninanen n a a E 9 6 Preparing Slide Kamera ROAD JIB crane to WOMK ccscsssssscssssssssesssessesssesacscesecsssesesavsesesaracsesavscseesassssesas 11 6 1 Setting up counterweight arm Of the CrANG ccccsssessssssssssssssssssscsessssesssessesssesesecsesesacsesesacseeesaceseesesacersesas 11 62 Se WING UO wokna amm Ol ING Cl Ai setae tera crrran seen ae ceraets state aera oc Panera 12 T Mounting equipment on ROAD JIB mounting plate cccccseccescsesseecssessseeecsecesseeessseessseesseeesssesaeeesssseeass 12 8 Slide Kamera HDN DC drive for ROAD JIB camera CLANE ceccsessssescsesseeeessesecsesecsssessese
9. ollowing product maintenance specifications The warranty excludes v unauthorized attempts to repair or modify vi mechanical damage caused during transport and operation of such features scratches dents pits dirt etc v flooding moisture To obtain warranty service the purchaser should deliver the damaged product together with a proof of purchase and proof of payment invoice cash register receipt The product will be accepted for warranty service on condition that it will be delivered with correctly filled in complaint form and properly protected during transport You can download the complaint form from www slidekamera com www slidekamera eu After the warranty period is exceeded any spare parts can be purchased directly from the manufacturer orin any selected points of sale PLEASE NOTE Any package sent at the expense of HET CNC s c 80 175 Gdansk Ul Kartuska 386 will not be received Slide Kamera ROAD JIB Camera Crane LA LECE made I POLAND
10. ort Always transport Slide Kamera ROAD JIB crane in a cover that allows to carry the crane safely so that all elements of the device are protected against any damage The manufacturer recommends using Slide Kamera PSK 3 1000mm transport cover designed for comfortable and secure transport of your photo and video equipment Weights are the elements that are transported seperately In order to ensure safe transport following conditions must be met m fold working arm of the crane and counterweight arm v tighten all clamping knobs to avoid the accidental spreading of the arms of the crane v secure the counterweight pin I fold the mounting plate of the crane as shown in the picture below remember to lock the clamping lever after m position crane base as shown in the picture below and lock it with clamping knob for tilt adjustment ROAD JIB crane properly prepared and assembled for transport 12 Terms of warranty All Slide Kamera products are covered manufacturer s warranty for a period of 12 months from the date of sale Warranty covers any design faults or of the material of the product which resulted in the product malfunctioning The warranty covers the repair or if the repair proves impossible replacement of the product with a new one Hovewer the cost of repair of the product cannot overrun the catalogue value of the product The warranty does not cover damage and or product defects resulting from the improper usage as well as not f
11. safely mount the camera in horizontal and vertical position Table below presents Slide Kamera ROAD JIB crane steering possibilities Table presenting Slide Kamera ROAD JIB crane steering possibilities Vertical Rotational head builtin Lock the clamping lever rotational ROAD JIB crane base of the rotational head movement Horizontal Unlock clamping knob Lock clamping knob for tilt movement for tilt adjustment adjustment and set the crane in a desired position Arm Slide Unlock three arm slide Lock three arm slide clamping clamping knobs knobs to lock the arm in a desired position Angular position Unlocking three arm Lock three arm slide clamping of the crane slide clamping knobs knobs to lock angular position mounting plate enables to control and of the crane mounting plate set the arms of the crane making it possible to set a desired angular position of the crane mounting plate Slide Kamera ROAD JIB Camera Crane 4 Specification Application Lengths Arm length range Mounting holes Rotational head Safety payload Material Mounting equipment on crane mounting plate Weight without weights Weights Blokada wysuwu ramienia Arm tilt Rotation Mounting plate angular position range For lifting and rotating the camera or photo camera together with the accessories Dedicated for mounting on Slide kamera HST series tripods HST 2 or HST 3 Transport length 1022mm Counterw
12. sessecsssecessessssecasenses 13 To y meU aa E A eee ere enna eee 13 IREE E E EE A AE A O EE PEN EE Gen A A E A N T 13 ii Sealy ahs ole 9 e E E AAA E E EE A A 14 EAE EEE a E E E E N E E eee 14 Slide Kamera ROAD JIB Camera Crane 1 Elemens and construction of Slide Kamera ROAD JIB camera crane Once the shipmentis received please make sure that all the elements of Slide Kamera ROAD JIB crane are inside Set includes M Slide Kamera ROAD JIB crane with built in rotational head v counterweight weights 2x2kg 1x1kg 1x0 5kg Construction of ROAD JIB camera crane Counterweight weights 2x2kg 1x1kg 1x0 5kg 1 Counterweight arm 2 Sliding weight 3 Working arm of the crane 4 Crane mounting plate 5 Camera crane base 6 Built in rotational head with 3 8 and 1 4 holes 7 Sliding weight locking knob 8 Counterweight safety nut 9 Slide Kamera ROAD JIB Camera Crane Elements of ROAD JIB crane base Clamping knob for tilt adjustment 1 Pin that locks counterweight arm 2 Arm slide clamping knobs 3 1 4 hole 4 3 8 hole 5 Clamping knob that locks the rotational head 6 Elements of mounting plate Mounting groove 1 Four M4 holes 2 3 8 photographic screw 3 1 4 photographic screw 4 Grub that locks 1 4 and 3 8 photographic screws 5 Rubber plates 6 Clamping lever that locks the position of the mounting plate 7 Slide Kamera ROAD JIB Camera Crane 2 Addi
13. tional accessories Tripods Slide Kamera HST 2 tripod 700 or 920 1 HST 2 series tripods are also available without HSTA 1 wheels Slide Kamera HST 3 tripod 2 Tripod sockets Slide Kamera HCZ 75 100mm socket Manfrotto system 3 Slide Kamera HCZ 75 100mm socket Miller system 4 Slide a HCZ 75 100mm socket Sachtler system 5 Half ball leveler Articulated arm Manfrotto MN520BALL BALLSH 75mm 6 11 Magic arm for DSLR 8 Manfrotto MN500BALL BALLSH 100mm 7 Slide Kamera AF 17 articulated arm 9 Slide Kamera ROAD JIB Camera Crane Transport Slide Kamera PSK 3 cover 10 Adapters Motion controllers Slide Kamera AKC 3 adapter 11 Slide Kamera HDN DC drive for ROAD JIB crane 12 w 3 Product description t Slide Kamera ROAD JIB is an ultralight 4 5 kg portable and compact camera crane used for cameras and photo cameras of a total weight up to 3 5 kg It is equipment that offers great possibilities of creating images allowing to achieve excellent results during film realisations It allows to take smooth rise up and fall down crane shots and to film from the places previously inaccessible for the operator It also allows to present the scene from multiple perspectives while maintaining perfect smoothness of motion Telescopic aluminium construction allows to extend arms of the crane in no time thus giving you a possibility to spend more time on shooting instead of on setting up the equipm
14. tst slipping as well as protect against any scratches Steel joint of high durability and resistance to damage allows to safely mount the camera in horizontal and vertical position within the angular range of 90 Clamping lever on the plate allows to lock it rigidly in any position Steel joint 1 Clamping lever that locks the position of the mounting plate 2 Mounting groove 3 Four M4 foles 4 3 8 photographic screw 5 1 4 photographic screw 6 Grub that locks 1 4 and 3 8 screws 7 Rubber plates 8 Slide Kamera ROAD JIB Camera Crane 8 Slide Kamera HDN DC drive for ROAD JIB camera crane Slide Kamera HDN DC drive for ROAD JIB crane allows to perform smooth rise up and fall down movements of the crane arm with a speed set by the user The drive works with Slide Kamera ROAD JIB and HKR 2 cranes HDN drive allows to move the arm of the crane steadily with a setpoint speed as well and to make Timelapse photos 9 Safety measures Working with Slide Kamera ROAD JIB crane of 1450mm long working arm and maximum acceptable weight including counterweights and mounted accessories up to 15kg it is extremely important to pay special attention to the safety when using the device Because of the weight and length of the arm any impact caused by either the arm or any device mounted on the crane may result in serious injuries or equipment damage All clamping knobs and pin should be operated as instructed It is important to
Download Pdf Manuals
Related Search