mountune mTune Quick Start Guide
Contents
1. d mTune Quick Start Guide v1 0 Ei mountune mTune Quick Start Guide STOP To maintain any warranty provision otherwise entitled to you and to ensure correct operation and reliability calibrations loaded via an mTune handset must be installed together with the correct mountune hardware Installation must be carried out at a Ford Dealer or mountune USA to ensure vehicle warranty coverage See warranty document for details Product Introduction Congratulations on the purchase of the mTune hand held device The mTune is an OEM ECU flashing and engine monitoring device that will flash the ECU with an engine calibration map mountune maps were developed to specifically to work in concert with the mountune hardware from the Ford Focus ST MP275 and the mountune Ford Fiesta ST MP215 Upgrade Packages By flashing the ECU with the mountune map this will ensure the engine performs as intended and maintain its 50 state legal emissions status The mTune can e Reprogram the factory engine control unit ECU with a mountune map through the on board diagnostic OBD II port e Monitor and log vehicle sensor data using on screen digital gauges e Read and clear engine diagnostic trouble codes DTCs e Measure 0 60mph 1 4 mile times and generate a dyno plot e Estimate instantaneous fuel economy Supported Vehicle List o 2013 2014 Ford Focus ST o 2014 Ford Fiesta ST o 2015 Ford Fiesta ST In Box Contents OBD II Cable USB Cable U2. 4 Connect the small end of the OBD II cable to the port on the bottom of the mTune SDa 5 Make sure the clasp on the OBD II cable firmly engages with the port Er t 6 Next press the ENGINE START STOP button once to turn on the ignition The engine should not be running during this installation process 7 Select Install on the mTune to proceed with installation mTune Quick Start Guide v1 0 WARNING Do not disturb the mTune OBD II cable or open vehicle doors while installation is taking place Failure to do so may result in incomplete ECU reprogramming which may render the vehicle inoperable mTune Buttons Cancel oe iene UP on Scroll Down Vehicle Identification The mTune will attempt to automatically determine the target vehicle for installation If the mTune successfully identifies the vehicle Verify that the identified vehicle is correct and press OK to confirm If an error occurs Please reference the Troubleshooting section of the mTune User Manual for additional information Please visit the mountune website to download the User Manual ECU Map Selection After the mTune identifies the vehicle it will present a map for that vehicle This map will become the base map for the vehicle Ensure that all of the mountune components have been properly installed on the vehicle before flashing the map into the ECU After confirming that the mountune components have been properly installed on
3. SB 2 0 A to Micro B mTune Quick Start Guide v1 0 WARNING To maintain any warranty provision otherwise entitled to you and to ensure correct operation and reliability calibrations loaded via an mTune handset must be installed together with the correct mountune hardware Installation must be carried out at a Ford Dealer or mountune USA IMPORTANT For installation purposes it is important to ensure that the vehicle s battery has adequate power for both the mTune and the ECU Because of this it is recommended that all in car electronics and vehicle lights are turned off during the installation process to reduce drain on the vehicle s battery For improved safety during installation a car battery charger can be connected to the vehicle during the installation and ECU flashing process Getting Started 1 You will need the mTune and OBD II cable to perform the installation Make sure the key fob is present inside the cabin 2 Locate the vehicle s OBD II port Location of the OBD II port may vary depending on the vehicle model Some models are equipped with a covered OBD II port Image 1 While other models have the OBD II port located just under the plastic trim behind the hood release lever Image 2 Image 2 a l mTune Quick Start Guide v1 0 aii 3 Plug the OBD II cable into the OBD II port under the dash of vehicle Then connect the small end of the OBD II cable to the port on the bottom of the mTune
4. the vehicle press OK again to proceed Install mTune ECU Programming The mTune will proceed with installation to the vehicle At this point the mTune reprograms the vehicle s ECU with the new mountune program data and calibration parameters from the map file This process will take several minutes to complete Note that during installation the in dash display will go blank and the HVAC controls will reset After installation if the vehicle is equipped with a MFT SYNC system a message will appear that it is performing maintenance This is normal behavior Installation Complete The last installation process the mTune goes through is clearing trouble codes When this step is complete turn off the ignition and wait for approximately ten seconds After this last process is done your screen should now display Installation Complete You may now unplug the mTune from the vehicle The mTune does not need to be plugged in to the vehicle again unless it is to be used for performance testing live data monitoring or data logging features Please note that the mTune is designed to work with only one vehicle Once the mTune is installed it cannot be used with another vehicle Please contact mountune if you require technical support Mountune LLC Phone 714 424 9400 11215 Young River Avenue Office Hours 9AM 5PM Monday Friday Fountain Valley CA 92708 Email usa mountune com
Download Pdf Manuals
Related Search