(Milwaukee LDM80_EN.fm)
Contents
1. gt RE a 20 last displays are displayed Milwaukee LDM 80 Delete Memory A T z0 te gt 2 sec 2 sec The value from simultaneously the main line can be used for fur Memory is completely de ther calculations leted Calibration of tilt sensor Tilt Calibration 2 sec simultane N SG x Place device on absolutely flat sur face Turn the device horizontally by 180 and place it again on absolutely flat surface Turn the device and place it again on ab solutely flat surface After 2 sec the device goes back to the nor mal mode Turn the device horizontally by 180 and place it again on absolutely flat surface Milwaukee LDM 80 Technical Data Distance measurement Typical Measuring Tolerance 1 5 mm 0 06 in Maximum Measuring Tolerance 2 5 mm 0 10 in condition Range of target plate 80 m 262 ft Typical Range 80 m 262 ft Range at unfavourable 60 m 197 ft Smallest unit displayed 0 1 mm 1 32 in laser point at distances 6 30 50 mm 10 50 80 m Tilt measurement Measuring tolerance to laser 0 2 beam Measuring tolerance to 0 2 housing Range 360 Laser class 2 Laser type 635 nm lt 1 mW Protection class IP54 dust and splash water protected Autom laser switch off after 90 s Autom power switch off a2. The result is shown in the main line and the measured value above This process can be repeated as required The same process can be used for adding or subtracting areas or volumes The next meas The next meas urementis added urement is sub to the previous tracted from the one previous one Milwaukee LDM 80 Measuring Functions Area 1x si A S Aim laser at first Aim laser at sec target point ond target point amp 19 823m Circumference CTIE ni Area Milwaukee LDM 80 O Rs The result is shown in the main line and the measured value above Measuring Functions Volume Aim laser at first a Aim laser at sec j Aim laser at third target point ond target point target point The result is shown in the main line and the 80 208 m Circumference measured value above wm 209 703 Ga Wall areas pa 24224m Ceiling floor area 16 5694 M Volume Milwaukee LDM 80 Measuring Functions Pythagoras 2 point Aim laser at up per point Aim laser at up per point Notice additional Pythagoras measurement in formation at the bottom of the next page Aim laser rectan gular at lower point Aim laser at rec tangular point Notice additional Pythagoras measurement in formation at the bottom of the next page Milwaukee LDM 80 Measuring Functions Pythagoras partial height Aim laser at rec tangular point Aim laser at 2n
3. Table of Contents Instrument Set up Calibration Introduction Calibration of tilt sensor Tilt Calibration Overview i Display Technical Data Insert batteries Operations Switching ON OFF Safety Instructions Message Codes Areas of responsibility Beep ON OFF Permitted use Illumination ON OFF Prohibited use Adjusting measuring reference tripod Hazards in use Multifunctional endpiece Limits of use Distance unit setting Disposal Tilt unit setting Electromagnetic Compatibility EMC Timer automatic release FCC statement applicable in U S Laser classification Measuring Functions Labelling Measuring single distance Permament Minimum Maximum measuring Add Subtract Pythagoras 2 point Pythagoras 3 point Pythagoras partial height Stake out Smart Horizontal Mode Height tracking Memory 20 last displays Delete Memory Milwaukee LDM 80 Instrument Set up Introduction The safety instructions and the user manual should be read through carefully before the product is used for the first time a The person responsible for the product must ensure that LU all users understand these directions and adhere to them The symbols used have the following meanings ZAWARNING Indicates a potentially hazardous situation or an unintended use which if not avoided will result in death or serious injury CAUTION Indicates a potentially hazardous situation or an unintended use which if not avoided may result in mi
4. allations which are unprotected e Aiming directly in the sun Hazards in use WARNING Watch out for erroneous measurements if the instrument is defective or if it has been dropped or has been misused or modified Carry out periodic test measurements Particularly after the instrument has been subject to abnormal use and before during and after important measurements CAUTION Never attempt to repair the product your self In case of damage contact a local dealer WARNING Changes or modifications not expressly approved could void the user s authority to operate the equipment Limits of use Refer to section Technical data The device is designed for use in areas permanently habitable by humans Do not use the product in explo sion hazardous areas or in aggressive environments Milwaukee LDM 80 Disposal CAUTION Flat batteries must not be disposed of with household waste Care for the environ ment and take them to the collection points provided in accordance with national or local regulations The product must not be disposed with household waste Dispose of the product appropri ately in accordance with the national regulations in force in your K country n Adhere to the national and country specific regulations Product specific treatment and waste management can be downloaded from our homepage Electromagnetic Compatibility EMC WARNING The device conforms to the most string
5. d point Aim laser at up per point Pythagoras Pressing the measuring key for 2 sec in the function activates automatically measurements Minimum or Maximum measurement Milwaukee LDM 80 Measuring Functions Stake out Two different distances a and b can be entered to mark off de fined meas ured lengths lt A aA i Approve value b and start Adjust value value pa measurement Move device When approaching a stake slowly along the out point to less than 0 1 m ar the instrument starts to beep ir eae b The function can be stopped saved 0 240 m is missing by pressing the CLEAR OFF up to next 1 012 m paton distance Milwaukee LDM 80 Measuring Functions Smart Horizontal Mode NA Press key again to switch off horizontal measure ment Aim laser at target up to 360 and a transverse tilt of 10 Height tracking This function displays continous ly the tracking height if the device is turned on a tripod No 2nd dis tance measuring is needed as only the angle is automatically measured Aim laser at upper points and Aim ee at lower angle height tracking starts au point tomatically The tracked height y is in 90 to the ist 6 eS aimed point 6 932m 2 x 30 g B Tracking g 827 L y engle i Stops Height tracking and i m y height displays last measurement Milwaukee LDM 80 Measuring Functions Memory 20 last displays z0
6. ent requirements of the relevant standards and regulations Yet the possibility of causing interference in other devices cannot be totally excluded Safety Instructions FCC statement applicable in U S This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential instal lation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful inter ference to radio communications However there is no guarantee that inter ference will not occur in a particular instal lation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interfer ence by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Laser classification The device produces visible laser beams which are emitted from the instrument It is a Class 2 laser product in accordance w
7. fter 180 s Battery durability 2 x AAA up to 5000 measure ments Dimension H x D x W 117 x 57 x 32 mm 4 6 x 2 4 x 1 3 in Weight with batteries 0 14 kg 4 938 oz Temperature range Storage Operation 25 to 70 C 13 to 158 F 10 to 50 C 14 to 122 F applies for 100 target reflectivity white painted wall low background illumination 25 C applies for 10 to 500 target reflectivity high back ground illumination 10 C to 50 C Tolerances apply from 0 05 m to 10 m with a confi dence level of 95 The maximum tolerance may deteriorate to 0 1 mm m between 10 m to 30 m and to 0 2 mm m for distances above 30 m applies for 100 target reflectivity background illumination of approximately 30 000 lux after user calibration Additional angle related deviation of 0 01 per degree up to 45 in each quadrant Applies at room temperature For the whole operating temperature range the maximum deviation increases by 0 1 For accurate indirect results the use 1 ofa tripod is recommended For accurate tilt measurements a trans verse tilt should be avoided Milwaukee LDM 80 Distance measuring yes Min Max measuring yes Permanent measuring yes Stake out yes Addition Subtraction yes Area yes Volume yes Pythagoras 2 point 3 point partial height Smart Horizontal Mode yes Indi
8. he front of the device Distance is measured from the rear of the device standard setting Milwaukee LDM 80 Distance is measured from the tripod thread permanently The orientation of the endpiece is automatically detected and the zero pointis accordingly ad justed Operations Distance unit setting Tilt unit setting Switch between the Switch between the following units Ce following units 0 00 ft 2 sec 0 0 0 00 1 32 simultaneously 0 0 0 00 in Once the key is released with the laser activated the remaining sec onds until the measurement are displayed in a countdown The de layed release is recommended for Adjust delay of au precise aiming e g at long distanc tomatic release es It avoids shaking of the device max 60 sec when pressing the measurement standard setting key 5 sec Milwaukee LDM 80 Measuring Functions Measuring single distance Target surfaces Measuring errors can occur when meas uring to colourless liquids glass styrofoam or semi per meable surfaces or when aiming at high gloss surfac es Against dark surfaces the measuring time increases The minimum and maximum dis tance measured is displayed min max The last value meas ured is displayed in the main line 3 0 3 Stops permanent mini mum maximum measuring Used to measure room diagonals maximum val ues or horizontal distance minimum values
9. ith IEC60825 1 2007 Radiation safety of laser products Laser Class 2 products Do not stare into the laser beam or direct it towards other people unnecessarily Eye protection is normally afforded by aversion responses including the blink reflex WARNING Looking directly into the beam with optical aids e g binoculars telescopes can be hazardous CAUTION Looking into the laser beam may be hazardous to the eyes Milwaukee LDM 80 Labelling Code 4000 4461 26 max Power lt 1mW Wave length 620 690nm Techtronic Industries GmbH Max Eyth Stra e 10 71364 Winnenden Germany ry E Cover the English text on the rating plate with the in cluded sticker in your national lan guage prior to first operation 4 A LDM 80 4000 4461 26 Ser No XXXXX M JJJJ Art No XXXXXX P N 23456789 Subject to change drawings descriptions and technical data without prior notice
10. nd adhere to them Areas of responsibility Responsibilities of the manufacturer of the original equipment Techtronic Industries GmbH Max Eyth Strasse 10 71364 Winnenden Germany The company above is responsible for supplying the product including the User Manual in a completely safe condition The company above is not responsible for third party accessories Responsibilities of the person in charge of the instrument e To understand the safety instructions on the product and the instructions in the User Manual e To be familiar with local safety regula tions relating to accident prevention Always prevent access to the product by unauthorised personnel Safety Instructions Permitted use e Measuring distances Tilt measurement Prohibited use e Using the product without instruction Using outside the stated limits e Deactivation of safety systems and removal of explanatory and hazard labels Opening of the equipment by using tools screwdrivers etc e Carrying out modification or conversion of the product e Use of accessories from other manufac turers without express approval Deliberate dazzling of third parties also in the dark Inadequate safeguards at the surveying site e g when measuring on roads construction sites etc Deliberate or irresponsible behaviour on scaffolding when using ladders when measuring near machines which are running or near parts of machines or inst
11. nor injury and or appreci able material financial and environmental damage Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner Overview Display NN On Measure Pythagoras ee Stake out g Measuring 4 reference WS Clear Off Milwaukee LDM 80 Instrument Set up Display Horizontal measurement Stake out Measuring reference Circumfer Wall area Addition Subtraction 2nd result tit OBE 700 ftim Insert batteries Area Volume Timer mK Pythagoras Battery Min Max Measuring Units Main line Milwaukee LDM 80 To ensure a reli able use do not use zinc carbon batteries Change batter ies when battery symbol is flash ing tO E Operations Switching ON OFF Clear Message Codes Press ON but 1x w gt 2x Ifthe info icon appears with a ton 2 sec to number observe the instruc _startcontinuous c c tions in section Message 1 laser mode If e OFF i OFF Codes no key is Example 2 sec pressed for 180 A Leave actual Device is F eae A Undo last action function go to de turned OFF 5 tomatically a EE e 255 Illumination ON OFF 2 sec simultaneously c gt X simultaneously s wr Milwaukee LDM 80 Operations Adjusting measuring reference tripod A gt Distance is measured from t
12. rect height Height tracking yes Memory 20 displays Beep yes Illuminated display yes Multifunctional endpiece yes Message Codes If the message Error does not disappear after switching on the device repeatedly contact the dealer If the message InFo appears with a number press the Clear button and observe the following instructions No Cause Correction 156 Transverse tilt Hold the instrument greater than 10 without any transverse tilt 162 Calibration mistake Make sure the device is placed on a abso lutely horizontal and flat surface Repeat the calibration procedure If the mistake still occurs contact your dealer 204 Calculation error Perform measurement again 252 Temperature too Let device cool down high 253 Temperature too Warm device up low 255 Received signaltoo Change target surface weak measuring e g white paper time too long 256 Received signaltoo Change target surface high e g white paper 257 Too much back Shadow target area ground light 258 Measurement Correct range outside of meas uring range 260 Laser beam inter Repeat measurement rupted Care e Clean the device with a damp soft cloth Never immerse the device in water e Never use aggressive cleaning agents or solvents Milwaukee LDM 80 Safety Instructions The person responsible for the instrument must ensure that all users understand these directions a
Download Pdf Manuals
Related Search