User manual Double ON/OFF connector FGS 221 v1.1 - Pepper
Contents
1. IBA ROU User manual Double ON OFF connector FGS 221 v1 1 F R G P Remotely controlled double ON OFF connector manufactured by FIBARO system is intended for work in electric box or anywhere where two loads up to 1 5kW are needed to be controlled It is possible to send a signal to any system which we wont to integrate with FIBARO system Technical features 110 230 V 10 Supply voltage 50HZ 60Hz Maximal load current for single AC input Maximal load 8A 230V 50 60Hz current for single 8A 30V DC input Input power up to 2x1 5kW Conformity with EN 55015 interferences the EU norms EN 60669 2 1 exploitation safety System 105 C temperature limitation Work 0 40 C temperature i assembly in gt 50mm oxes Radio protocol Z Wave Radio frequency 868 MHz up to approx 50m on the open area up to approx 30m on the building premises depending on building materials Range Dimensions constitute a signal duplicator In the case height x width x 15 x 42 x 38 mm in which a direct way of connection depth between the transmitter and the receiver cannot be established the connection may be realized via the application of other devices mediating in the transmission Technical information Control via devices of FIBARO system or of any Z wave controller e Microprocessor control FIBARO is a two way wireless system It means that not only the signal is sent to the e Executiv2. Parameter number 42 Smoke CO CO2 alarm set on relay 2 default value 3 ALARM FLASHING Parameter number 33 Temperature alarm set on relay 1 default value 1 ALARM RELAY DISABLE Parameter number 43 Temperature alarm set on relay 2 default value 1 ALARM RELAY DISABLE Parameter number 39 Time of active alarm Default value 600 VI Advanced function Alarm frames handling Fibaro systems allows to set reaction of devices on alarm situations reaction on ALRM_REPORT and SENSOR_ALARM _REPORT frames FIBARO double ON OFF connector handles following types of alarms e 0x00 hex GENERAL _ ALARM e 0x03 hex ALARM CO2 0x02 hex ALARM CO 0x01 hex ALARM SMOKE e 0x05 hex ALARM WATER 0x04 hex ALARM HEAT Alarm frames are sent by sensor devices of the system e g flood detectors smoke detectors motion detectors etc Device can react on received frames in following ways configuration can be done in configuration parameters see V Configuration 0 DEACTIVATION device don t react on alarm frames e 1 ALARM ON device turns on after alarm detection e 2 ALARM OFF device turns off after alarm detection e 3 ALARM FLASHING device periodically changes state on opposite after alarm detection turns on turns off alternately Double ON OFF connector has two independent alarm groups every relay can individual react on alarm frames Fibaro syste
3. danger caused by the current 1 Before the commencement of double connector assembly procedure ensure that the power is turned off 2 Connect the double ON OFF connector according to the diagram below 3 Place the whole device in the electric box Place the antenna the hints are located below figure 1 single connector Be lejalalajaja T SF L A option with alternative load power supply Fig 1 Electrical diagram of double ON OFF connector s connection LEGEND L phase clamp N neutral clamp input clamp of load power supply S1 a clamp for the button number 1 possesses an option to set the device to the learning mode S2 a clamp for the button number 2 O1 output clamp for the load number 1 O2 output clamp for the load number 2 CAUTION there is possibility of supply with voltage different then supply voltage of ON OFF connector it can be different phase different voltage or even DC power supply See Technical features for more option with alternative load power details supply Double connector Endurance on device depends on power load For resistance power load light bulb etc 8A is 200 000 connection cycles If it is inductive load e g glow tube with cos 0 6 it is needed to restrict current to 6A in order to keep same device life time HINTS FOR ANTENNA SETTLEMENT Conduct the antenna ata possibly long distance from
4. for the improper work of the Device which stems from the physical defects material oor production defects found in the Device within the period of 12 months from the day of its sale The Guarantee is in force and is applied only on the territory of the Republic of Poland During the period of Guarantee validity the Guarantor shall be obliged to remove the revealed 6 7 defects free of charge by means of repair or replacement at the Guarantor s sole discretion of all of the defective Device s elements for new or regenerated and undamaged elements In the case of the lack of possibility to perform repair works the Guarantor reserves the right to replace the Device for a new or generated and undamaged one whose physical state shall not be worse that the state of the Device owned by the Client 9 Should in special cases e g the lack of Device within the commercial offer the replacement of the Device for the one of the same type be impossible the Guarantor may replace the Device for another one with possibly most similar technical parameters 40 Such an action shall be considered as the execution of the Guarantor s duties The Guarantor shall not refund money spent on the purchased Device 11 The owner of the valid Guarantee document reports the claims with regard to the Guarantee via guarantee service One should remember that before the report of guarantee claim it is useful to cont
5. the Fibaro system controller by means of the following icon Fig 2 Double ON OFF connector s icon power and until 5 seconds click within Home Center controller Turn on turn off devices connected to double ON OFF connector can be done by clicking appropriate icon ON OFF Multichannel devices have in one physical ee device two or more independent circuits IV Association The application of association allows double ON OFF connector to directly control the other device within z wave network e g other dimmer transmitting connector roller shutter V Configuration In Fibaro interface following settings are available in simple options which we CAUTION Association allows choose by checking appropriate fields for sending of direct control commands between the In order to move to the double ON OFF devices and the main connector s configuration with the controller but it does not application of Fibaro controller move to the device option clicking on the following icon participate into the process of communication Choose device option The double ON OFF connector allows for association of two groups 1 The group is ascribed to the key number 1 Parameter number 1 l Activation deactivation of ALL ON ALL 2 The group is ascribed to the key number OFF functions default value 255 Possible configuration parameters 255 Default ALL ON active ALL OFF active ALLON non active ALL OFF non activ
6. act our company via telephone or via the internet technical assistance In more than a half cases the Client s problems are solved remotely the12 fact which allows to avoid the loss of time and costs with regard to the unnecessarily activated Guarantee procedure Should the remote solution of the problem be impossible the Client will be asked to fill in the application form in order to obtain authorization via website Www fibargroup com In the case of reporting of a correct claim You will receive the confirmation of its reception as well as a unique report number RMA There is also a possibility to report the claim via telephone call In such a case the call will be recorded the fact about which the Client will be informed by the consultant before the acceptance of claim report Immediately after the report reception consultant will inform the Client about internet the report number RMA the so called In the case of reporting of a correct claim the representative of the Authorized Guarantee Service hereinafter referred to as AGS will contact the Client and determine the day and the place of the visit of technicians who will check the correctness of Device s functioning in presence of Client The defects revealed during the period of Guarantee validity shall be removed within 30 days at latest counting from the date of delivery of the Device to AGS The period of Guarantee validity shall
7. be extended with time in which the Device is kept by AGS The claimed Device shall be rendered accessible by the Client with the complete standard equipment and documents confirming its purchase The elements replaced with regard to the Guarantee constitute the ownership of the Manufacturer All of the elements enumerated within claim process are encompassed with the Guarantee valid until the period of validity of the Device s basic Guarantee The period of Guarantee validity for a replaced element is not subject to extension The cost of travel to the claimed Device or of its delivery to the service shall be borne by the Guarantor In the case of an unjustified summoning of the service the Service has a right to impose on the Client the costs of travel and manipulative costs connected to the explanation of the matter AGS rejects to accept the claim only in the following cases in the case in which the Device is exploited against its intended use and the user s manual in the case in which the Client renders accessible the Device which is incomplete has no fittings or data plate in the case in which the defect is different than material or productive one found in the Device 14 15 in the case of the invalid Guarantee document and the lack of purchase receipt The Guarantor shall not be responsible for the defects in property caused by the defective Device The Guarantor shall not be responsib
8. e ALLON non active ALL OFF active ALLON active ALL OFF non active The double ON OFF connector enables the control of 16 ordinary devices and 7 MultiChannel ones 1 field out of which is reserved for the network controller It is recommended not to use more than 10 devices because the time required by the device to issue a command to each of the 1 associated device may be very long In order to add an association with the application of Home Center controller one has to move to the device options clicking on the following icon Parameter number 13 Allows change of 4 state turn on turn off for bistable switches see parameter 14 default value 0 Choose device options Then determine the group and the type of device to be associated The process of sending by the controller of the proper information to the 0 ON OFF sets on change of key state devices included in the associated groups may take even several minutes The possibility of parameter change 0 1 1 ON is active when contacts are closed OFF is active when contacts are open CAUTION If during the time in which the device sends Parameter number 14 The type of control commands the key is Switch may be chosen from mono stable pushed anew the process of or bistable switches default value 1 sending of present commands will be interrupted and the process of sending of new commands will 0 mono stable switch occur The po
9. e elements relays receivers but that they additionally send a e The device co operates with confirmation of its reception Thus they mono stable bistable confirm their state so that we may verify whether the device has actually been PSOE E TE E E turned on The safety of FIBRO system _ transmission is comparable with wire All of the works connected with i systems the execution of device s y a cae E FIBARO works within a free band for data a ony ue kee ane authorized transmission upon the frequency of electrician The national law regulations have 868MHz Each FIBRO network possesses to be observed its own unique home ID number Therefore there is a possibility to co exist for two or the more independent systems within one building without any conflict Danger Life danger caused by current Even when the device is turned off there may be voltage on its Despite the fact that Z Wave technology is output All of the works which aim at change new just as Wi Fi it officially became an of setting configuration or of load charge obligatory standard Many manufacturers should always be executed with the voltage from different fields offer solutions based turned off by previously turned on safety upon the Z Wave technology and they are device mutually compatible Such a situation Hints results in the fact that the system is future The double ON OFF connector prospective and will allow for further must not be connected to the l
10. e extremely unfavourable conditions that is in the presence of high humidity dustiness too low 18 frost or too high temperature The detailed terms and conditions in which the Device may be exploited suspends the Purchaser s rights stemming from the _ product s incompatibility with the agreement are determined within the user s manual The device may be used with all of the devices which possess Z Wave certificate It should also co operate with the devices manufactured by different manufacturers Every device which is compatible with Z Wave may be included in Fibaro system the defects caused as a result of exploitation of accessories not recommended by the Manufacturer caused by the defective electrical installation conducted by the user including the application of incorrect safety devices the defects caused by the Client s negligence of conduction of maintenance and service procedures FIBARGROUP enumerated within the user s manual FIBARO the defects caused by the In the case of technical questions please MEENA Zx contact the client service centre in Your exploitation of non original spare company parts and equipment parts i www fibargroup com inappropriate for a given model execution of repair works or changes conducted by unauthorized persons the defects caused by continuity of work with defective Device or fittings The scope of the Guarantee repair w
11. le for indirect collateral special consequential or moral losses nor for damages including lost benefits savings data advantages third party s claims as well as any other property or personal defects resulting from or connected to the exploitation of the Device The quality Guarantee does not encompass the following issues mechanical defects cracks breaks cuts wears physical misshapes caused by a blow fall or dropping on the Device of another object or caused by the exploitation against the Device s intended use determined within the user s manual the defects caused by the external reasons such as flood thunderstorm fire lightning stroke calamities earthquakes wars social unrests force majeure unforeseen accidents robbery liquid flooding bacteria leakage weather conditions the influence of sunbeams sand humidity high or low temperature air contamination the defects caused by the improperly working software as a result of virus attack or caused by the lack of conduction of software updating procedure according to the Manufacturer s recommendations the defects caused by overvoltage within the power supply and or telecommunication network or by the execution of the Device s connection via a method incompatible with the users manual or by connection of other products whose connection is not recommended by the Manufacturer caused by the work or storage of the Device in th
12. m allows to handle only Alarm Version 1 Reports VII Double ON OFF connector s operation The double ON OFF connector may be operated via the following operational elements any controller compatible with the system e g Home Center controller mobile phone e g IPhone as well as mobile phones of other manufacturers equipped with appropriate control application devices of tablet type e g IPod via PC with the use of internet browser via the key connected to the double ON OFF connector VIII Procedures conducted in the case of interruptions The device does not react to the programmed transmitter e Ensure that the maximal range was not exceeded and that on the signal way there are no obstacles such as metal surfaces e g metal wardrobes reinforced ceilings and bearing walls etc e Ensure if the device is not set to program mode e Repeat the process of programming one more time IX TERMS AND CONDITIONS OF THE GUARANTEE 1 2 3 The Guarantor of the Device quality is FIBAR GROUP Sp z o o hereinafter referred to as __ Manufacturer domiciled at Pozna 6A Cztopska Street 60 453 Poznan entered into the National Court Registry by the Regional Court in Poznan 8 Economical Department of the National Court Registry under the KRS number of 370151 NIP 7811858097 REGON 301595664 with company equity of 5000 PLN The Manufacturer shall bear the responsibility
13. metal elements connectors ring brackets etc in order to prevent interruption of the radio signal Metal surfaces located within the nearest surroundings e g metal boxes mounted under plaster metal frame slats may influence the reception capacity thus worsening the range of the device work Do not cut or shorten the antenna Its length is perfectly see the instruction of Home Center controller STEP 5 The double ON OFF connector enters the mode of adding and removing after a quick triple clicking of the key number 1 If it is bistable switch change its state three times adjusted to the band within within which the system works Caution I The double ON OFF connector cancels the learning mode after a single pushing of the key number 1 Thus the quadruple pushing of the key number 1 will not add the device to the network Caution It has to be emphasized that the key connected to the S1 activates the device s learning mode Include Exclude Caution II The double ON OFF connector is adjusted to work with bistable switches that is bipolar switch by default Dictionary Inclusion the device sends Node Info frame which enables During installation time it is recommended to use bistable keys to add it to Z Wave network Exclusion the removal of the device from Z Wave network Association control of other Z Wave network devices MultichannelAss
14. oad development More information may be heaver then recommended details found on the following website in technical data www fibaro com Connect in accordance with diagram placed in user manual Incorrect connection can beFIBARO creates a dynamic network dangerous structure From the moment of turning off the placement of particular devices of GENERAL INFORMATION ABOUT FIBARO system is automatically updated in the actual time via confirmation of states in the working mesh network FIBARO constitutes a system of house automatics based upon Z Wave A single universal box double ON OFF technology which does not require any connector will be hereinafter referred to as additional wiring In comparison with other double ON OFF connector With its systems FIBARO provides a range ofapplication one may turn on and turn off benefits In general radio systems create adevice connected to its clamps see direct connection between a receiver and Technical data via radio waves controllers a transmitter The radio signal isand a key directly connected to the double dampened by all of the obstacles found ON OFF connector along its way walls furniture etc in the apartment In the worst case the radio Il double ON OFF connector s assembly system will cease to perform its functions The advantage of FIBARO system is constituted by the fact that apart from both transmitting and receiving the devices also FIBARO SYSTEM Life
15. ociation control of other multichannel devices within Z Wave network 2 Double ON OFF connector s reset procedure STEP 6 The correct process of adding of the device to the network will be signalled on the controller see Home Center controller s instruction Ili Double ON OFF connector s activation The double ON OFF connector has got two procedures which enable to reset the 1 Double ON OFF connector s device installation procedure STEP 1 Connect the device according to the electric diagram shown on figure 1 Turn off the power supply 230V Addition or removal of the double ON OFF connector to or from z wave network Inclusion Exclusion STEP 2 The double ON OFF connector must be located within the range of Z Wave controller Fibaro Home Center because the mode of adding to Z Wave system requires the direct communication with the controller distance up to 40m STEP 3 Identify key number 1 If the device is connected as at figure 1 it will be key which closes circuit number 1 STEP 4 Set Z Wave controller Fibaro Home Center on the mode of adding or removing of the device to from the network Method Via the procedure of removing exclusion of the double ON OFF connector from the existing Z Wave network It is conducted with the application of a controller which possesses the function of adding and removing inclusion exclusion of devices from Z Wave network see Home Center con
16. ork does not encompass periodical maintenance or inspection of the Device especially cleaning regulations verification of functioning correction of service errors or software parameters or other activities which should be conducted by the user the Purchaser The Guarantee does not encompass the natural wear of the Device s elements as well as of other parts which possess determined period of functioning and are enumerated within the user s manual and technical documentation Should the type of produc s defect be not encompassed within the Guarantee the Manufacturer reserves the right to remove such a defect at his own discretion conducting the repair of the defective or damaged part or rendering the sub assemblies accessible for the conduction of the necessary repair works or replacement The Guarantee for the purchased goods does not exclude limit nor
17. ssibility of parameter change 0 1 1 bistable switch Double ON OFF connector FGS221 supports multichannel devices Parameter number 16 Saving of the device state after the power supply black out The double ON OFF connector will return to the last state before the power supply black out default value 1 The possibility of parameter change 0 1 0 the double ON OFF connector does not save the state after the power supply black out it returns to the turn off state 1 the double ON OFF connector saves the state before the power supply black out Possible configuration parameters for following parameters 30 33 40 43 0 DACTIVATION device don t react to alarm frames 1 ALARM RELAY DISABLE device turns off after alarm detection 2 ALARM RELAY ENABLE device turns on after alarm detection 3 ALARM FLASHING device periodically changes state on opposite after alarm detection during 10 minutes Parameter number 30 General alarm set on relay 1 default value 3 ALARM FLASHING Parameter number 40 General alarm set on relay 1 default value 3 ALARM FLASHING Parameter number 31 Flood alarm set on relay 1 default value 2 ALARM RELAY ENABLE Parameter number 41 Flood alarm set on relay 2 default value 2 ALARM RELAY ENABLE Parameter number 32 Smoke CO CO2 alarm set on relay 1 default value 3 ALARM FLASHING
18. troller s instruction Such a controller does not have to be a part of the network which hosts the removed device Method II To reset double ON OFF connector settings connect button S1 and hold button S2 3 Control of the double ON OFF connector via switches Mono stable switch after the key release the spring automatically bounces causing disconnection Turning the circuit 1 or 2 on off shortly push key corresponding to circut 1 or 2 refer to fiig 1 Bistable switch acts as a switch does not going back after the key release Turning the circuit on off the change of position of the key on opposed 4 Control of the double ON OFF connector via ALL ON ALL OFF command The double ON OFF connector executes ALL ON ALL OFF commands which may be sent via Home Center or other controller which belongs to the system Usually ALL ON ALL OFF commands are implemented within remote controls which use z wave protocol and are applied for issuing of commands directed to the whole system Both ALL ON and ALL OFF commands are accepted by the double ON OFF connector by default The implementation of changes may be executed by means of saving the correct value into the configuration register number 1 5 Double ON OFF connector s controller via main controller of Fibaro system Home Center After the conduction of procedure of adding of double ON OFF connector into the network it will be represented within
Download Pdf Manuals
Related Search