club laser 7 manual
Contents
1. ILDA CONTROL This laser can be controlled by any PC equipped with ILDA compatible software hardware As soon as the ILDA input 17 of the laser is connected with an ILDA compatible controller it will automatically switch to ILDA control mode From this moment on the laser will be completely controlled by the ILDA software the possibilities of the ILDA software will determine what you can do or not ILDA soft and hardware are available from several independent suppliers Some possible choices are PHOENIX software www bocatec de PANGOLIN software www pangolin com And many other up to you and your finances to see what is best for your needs MAINTENANCE e Make sure the area below the installation place is free from unwanted persons during servicing e Switch off the unit unplug the mains cable and wait until the unit has been cooled down During inspection the following points should be checked e All screws used for installing the device and any of its parts should be tightly fastened and may not be corroded e Housings fixations and installations spots ceiling truss Suspensions should be totally free from any deformation e When an optical lens is visibly damaged due to cracks or deep scratches it must be replaced e The mains cables must be in impeccable condition and should be replaced immediately when even a small problem is detected e In order to protect the device from overheat the cooling fans and ven2. Electric shock or malfunction may result If a foreign object enters the unit immediately disconnect the mains power e Locate the fixture in a well ventilated spot away from any flammable materials and or liquids The fixture must be fixed at least 50cm from surrounding walls Don t cover any ventilation openings as this may result in overheating Prevent use in dusty environments and clean the unit regularly Keep the unit away from children Inexperienced persons should not operate this device Maximum save ambient temperature is 40 C Don t use this unit at higher ambient temperatures Make sure the area below the installation place is free from unwanted persons during rigging de rigging and servicing Allow the device about 10 minutes to cool down before servicing e Always unplug the unit when it is not used for a longer time or before replacing the bulb or start servicing e The electrical installation should be carried out by qualified personal only according to the regulations for electrical and mechanical safety in your country e Check that the available voltage is not higher than the one stated on the rear panel of the unit e The power cord should always be in perfect condition Switch the unit immediately off when the power cord is squashed or damaged It must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard e Never let the power cord come into contact with oth
3. 3 f Lo D a A a 3 S St be Ge S a g be AE S 5 z EN SST ck GE EK Se EE E EREITEA SNES j K k FF UE Sd lk A 7 Gey weesen S aa Ra fae 3 v Dec DR Ir 14 i i F I SLA ti SLAVE 1 MASTER 3 CLUB LASER 7 BRITEQ 6 8 Value 1 2 64 128 Begin address 01 gt switch 1 ON values 1 Begin address 05 gt switch 1 3 ON values 1 4 5 Begin address 09 gt switch 1 4 ON values 1 8 9 Begin address 13 gt switch 1 3 4 ON values 1 4 8 13 Begin address 62 gt switch 2 3 4 5 6 ON values 2 4 8 16 32 62 e The display helps you to check if the desired starting address is correct e Once the address is set you can switch the unit on with the mains on off switch 1 CLUB LASER 7 ENGLISH USER MANUAL DMX CONFIGURATION Switched off D Auto Running 104 155 Auto Running Dot Line 156 207 Sound Mode 208 255 Sound Mode Dot SI 0 255 125 preprogrammed graphics 0 128 Rotation rotation by Z axis v ze Adjust the speed of the rotation Rolling by Y Axis et Adjust the speed of rolling Rolling by X Axis Adjust the speed of rolling Graphics move along the X axis Speed of moving Graphics move along the Y axis in Speed of moving f re owing pest sowiotast m 2 1 re seaming spect slowo fast l Yellow vn pune 96 127 Cyan 128 159 160 191 120 223 IN 224 255 BRITEQ 7 8 CLUB LASER 7 ENGLISH USER MANUAL 5
4. 3B laser Laser Radiation when open Avoid exposure to beam WARNING LABEL Laser Radiation Avoid exposure to beam Class 3B laser product LASER WARNING SIGN warns against a potentially dangerous laser when not used by skilled operators WARNING LABEL Laser Aperture CLUB LASER 7 ENGLISH USER MANUAL OVERHEAD RIGGING Important The installation must be carried out by qualified service personal only Improper installation can result in serious injuries and or damage to property Overhead rigging requires extensive experience Working load limits should be respected certified installation materials should be used the installed device should be inspected regularly for safety Make sure the area below the installation place is free from unwanted persons during rigging de rigging and servicing Locate the fixture in a well ventilated spot far away from any flammable materials and or liquids The fixture must be fixed at least 50cm from surrounding walls The device should be installed out of reach of people and outside areas where persons may walk by or be seated Before rigging make sure that the installation area can hold a minimum point load of 10times the device s weight Always use a certified safety cable that can hold 12times the weight of the device when installing the unit This secondary safety attachment should be installed in a way that no part of the installation can drop more than 20cm if the main a
5. Club Laser PA G A Operation Manual EN WWW BEGLEC COM Copyright 2008 by BEGLEC cva I KZ LU Reproduction or publication of the content in any manner without express permission of the publisher is prohibited Version 1 0 LIGHT RESEARCH A aes RECYCLE EN DISPOSAL OF THE DEVICE Dispose of the unit and used batteries in an environment friendly manner according to your country regulations FR DECLASSER L APPAREIL Debarrassez vous de l appareil et des piles usag es de mani re cologique Conform ment aux dispositions l gales de votre pays NL VERWIJDEREN VAN HET APPARAAT Verwijder het toestel en de gebruikte batterijen op een milieuvriendelijke manier conform de in uw land geldende voorschriften DU ENTSORGUNG DES GERATS Entsorgen Sie das Gerat und die Batterien auf umweltfreundliche Art und Weise gem den Vorschriften Ihres Landes ES DESHACERSE DEL APARATO Reciclar el aparato y pilas usadas de forma ecologica conforme a las disposiciones legales de su pais PT COMO DESFAZER SE DA UNIDADE Tente reciclar a unidade e as pilhas usadas respeitando o ambiente e em conformidade com as normas vigentes no seu pa s ENGLISH USER MANUAL OPERATION MANUAL Thank you for buying this Briteq product To take ful
6. ace and use any professional laser software to create stunning laser shows create logos etc e Laser projections can be adapted to the size of the venue with X Y image zoom controls e Graphics can be mirrored for projections behind a transparent screen e Blanking technology for nice separate beams e Perfect for use in clubs discotheques publicity exhibitions and many more e Complies to EN IEC 60825 1 for Laser Safety BEFORE USE e Before you start using this unit please check if there s no transportation damage Should there be any do not use the device and consult your dealer first Important This device left our factory in perfect condition and well packaged It is absolutely necessary for the user to strictly follow the safety instructions and warnings in this user manual Any damage caused by mishandling is not subject to warranty The dealer will not accept responsibility for any resulting defects or problems caused by disregarding this user manual Keep this booklet in a safe place for future consultation If you sell the fixture be sure to add this user manual Check the contents Check that the carton contains the following items e CLUB LASER 7 e dB25 dB25 ILDA cable e Flight case e 2 keys for key switch e Mains cable e Operating instructions BRITEQ 1 8 CLUB LASER 7 ENGLISH USER MANUAL SAFETY INSTRUCTIONS CAUTION To reduce the risk of electric shock do not remove the top cover AN Gg A No user
7. er cables e This fixture must be earthed to in order comply with safety regulations e Don t connect the unit to any dimmer pack LI LI Always use an appropriate and certified safety cable when installing the unit In order to prevent electric shock do not open the cover Apart from the lamp and mains fuse there are no user serviceable parts inside e Never repair a fuse or bypass the fuse holder Always replace a damaged fuse with a fuse of the same type and electrical specifications e In the event of serious operating problems stop using the fixture and contact your dealer immediately e The housing and the lenses must be replaced if they are visibly damaged e Please use the original packing when the device is to be transported e Due to safety reasons it is prohibited to make unauthorized modifications to the unit Important Never look directly into the light source Don t use the effect in the presence of persons suffering from epilepsy BRITEQ 2 8 CLUB LASER 7 ENGLISH USER MANUAL LASER SAFETY INSTRUCTIONS e According to the EN 60825 1 1994 A1 2002 A2 2002 regulations this laser falls under the classification 3B Direct eye exposure can be dangerous DANGER LASER RADIATION Avoid direct eye exposure Laser radiation can cause eye damage and or skin damage All protective measures for a safe operation of this laser must be applied e This product is a so called show laser emitting radiation with a wave
8. f MAINS INPUT with IEC socket and integrated fuse holder connect the supplied mains cable here COOLING FAN input used to cool the components inside the enclosure Make sure that the filter inside the fan is always in place before you turn the laser on The filter should be cleaned on a regular base Just tear off the plastic cover and clean the filter with a vacuum cleaner 4 COOLING FAN output used to cool the components inside the enclosure Make sure to never cover this fan outlet 5 HANGING BRACKET with 2 knobs on both sides to fasten the unit and a mounting hole to fix a mounting hook E a BRITEQ 3 8 CLUB LASER 7 10 11 12 13 14 15 16 17 18 BRITEQ 4 8 ENGLISH USER MANUAL SAFETY EYE used to attach a safety cable when the unit is rigged See paragraph overhead rigging ON OFF KEY ACTIVATED SWITCH used to switch the laser beam on off Use the keys to make sure only a skilled operator is able to switch the laser on INTERLOCK input used to connect the optional emergency stop switch see picture When you push this switch the laser beam will disappear immediately IMPORTANT For your own safety we strongly recommend to connect this optional switch DISPLAY shows the selected DMX address when the unit is in DMX mode Apart from DMX mode you can also select 4 other working modes see further to learn more about these modes DIP SWITCHES switches 1 8 are used to set the DMX address bet
9. g a suitable DMX cable e Determine which DMX address the laser needs e Set DIP switch n 10 in ON position ne e Set DIP switch n 9 in OFF position DMX ADDRESS SETUP ON DMX MODE e You will have to set the DMX starting address with the DIP switches 1 to DR Ho ong 2345678910 aN TOON TO AMON 8 Each of these switches has a corresponding DMX value written or under it You can combine the values of these switches to obtain any starting address between 001 and 255 OFF SOUND MODE OFF NO EFFECT Good to know the first 10 seconds after the laser is switched on none of the controls can be used You can operate the unit in 5 ways Dip Ta e Ta a Te we 4 8 16 32 BRITEQ 5 8 DMX ADDRESS DISPLAY 1 MUSIC CONTROLLED MODE The laser runs a preprogrammed sequence to the rhythm of the music Select this mode when only 1 laser is used standalone or when the laser cc emm mmm is placed as the first master unit in a chain with several Club Laser 7 units e Refer to the drawing on the right put DIP switch n 10 in OFF position setting of the other DIP switches is not important ON AUTO MODE DMX ADDRESS SETUP ON DMX MODE OFF SOUND MODE OFF NO EFFECT 2 MASTER SLAVE MODE You can connect several lasers together Please put the first unit of the chain in Music mode and all other units in Slave mode to make them all work in perfect sync a je i s J 3p ir
10. l advantage of all possibilities and for your own safety please read these operating instructions very carefully before you start using this unit FEATURES This unit is radio interference suppressed This product meets the requirements of the current European and national guidelines Conformity has been established and the relevant statements and documents have been deposited by the manufacturer e This device was designed to produce decorative effect lighting and is used in light show systems e A superb seven color clublaser equipped with 3 powerful temperature controlled lasers o 300mW Red laser 650nm o 60mW Green laser 532nm o 50mW Blue laser 473nm e Thanks to 20kHz scanners the club laser 7 projects rock steady sharp images containing up to 7colors e 100 ILDA compatible for full flexibility e Comes with adapted flight case included e The 5 user modes make this laser very easy to use o MUSIC CONTROL 100 plug amp play gt just connect the laser to the mains to start an incredible music controlled laser show based on the 128 internal programs Perfect for hiring companies o MASTER SLAVE mode Several units can be used in completely synchronized music mode amazing and very simple to use o AUTOMATIC mode all internal programs will be shown automatically no music needed o DMX mode just set a DMX address and take full control of all internal programs o ILDA mode connect the laser to any PC with ILDA compatible interf
11. length spectrum between 400 and 700 nm and producing lighting effects for shows e Due to the construction of this laser the beam is moved so fast that it can only hit the eye very short This is why the use of this laser for a Laser Light Show can be regarded as save Never direct the laser beam to people or animals and never leave this device running unattended This laser may only be used for shows The operation of a class 3B show laser is only allowed if the operation is controlled by a skilled and well trained operator Depending on the classification operating a laser product can produce laser radiation that may cause permanent eye damage and or skin damage The legal instructions for using a laser product vary from country to country The user must always inform himself on the legal instructions valid in his country and apply them to his situation Please note that BRITEQ cannot be made liable for damages caused by incorrect installations and unskilled operation DESCRIPTION COOLING FAN INPUT CLEAN THE FILTER REQULARLY AND DON T USE WITHOUT ALTER Itt N AE A A TNN oC MAIN ON OFF SWITCH used to switch the unit on of
12. ortant e On all slave units DIP switch n 10 must be put in ON position while DIP switches 1 to 9 are set to OFF refer to the drawing e Put on some music and adjust the MUSIC SENSITIVITY knob 14 until the laser works nicely to the rhythm of the music 3 FULL AUTOMATIC MODE The laser automatically runs a preprogrammed sequence e Refer to the drawing on the right put DIP switches n 9 and 10 in ON position setting of the other DIP switches is not important 4 DMX512 MODE USER MANUAL DMX ADDRESS DISPLAY ON AUTO MODE DMX ADDRESS SETUP ON DMX MODE Dooppeog 2345678910 ON OFF OFF SOUND MODE OFF NO EFFECT DMX ADDRESS DISPLAY ON AUTO MODE DMX ADDRESS SETUP ON DMX MODE OFF SOUND MODE OFF NO EFFECT the light effects due to interferences you must use a 900 to 1200 terminator at the 90 120 ohm end of the chain Never use Y splitter cables this simply won t work resistar Each effect in the chain needs to have its proper starting address so it knows which commands from the controller it has to decode The DMX protocol is a widely used high speed signal to control intelligent light equipment You need to daisy chain your DMX controller and all the connected light effects with a good quality XLR M F balanced cable To prevent strange behavior of DMX ADDRESS DISPLAY This is how you must setup and use the CLUB LASER 7 e Connect the unit to a DMX controller usin
13. serviceable parts inside Refer servicing to qualified service personnel only The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the use or the presence of un insulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operation and maintenance servicing instructions in the literature accompanying this appliance This symbol means indoor use only This symbol means Read instructions 2 bp gt L This symbol determines the minimum distance from lighted objects The minimum distance between light output and the illuminated surface must be more than 1 meter e To protect the environment please try to recycle the packing material as much as possible e A new light effect sometimes causes some unwanted smoke and or smell This is normal and disappears after some minutes e To prevent fire or shock hazard do not expose this appliance to rain or moisture e To avoid condensation to be formed inside allow the unit to adapt to the surrounding temperatures when bringing it into a warm room after transport Condense sometimes prevents the unit from working at full performance or may even cause damages e This unit is for indoor use only e Don t place metal objects or spill liquid inside the unit
14. tilation openings should be cleaned monthly e The interior of the device should be cleaned annually by experienced service people Attention We strongly recommend internal cleaning to be carried out by qualified personnel only SPECIFICATIONS Mains Input AC 100 240V 50 60Hz Fuse 250V 1 5A slow blow 20mm glass Total Power consumption 80W Sound Control Internal microphone DMX connections 3pin XLR male female DMX channels 10 channels DMX starting address 001 gt 256 Laser Power 60mW Green CW laser A 532nm 300mW Red CW laser A 650nm 50mW Blue CW laser A 473nm Laser scanners high speed 20kHz type Laser radiation class 3B Laser Safety Standard EN60825 1 1994 A1 2002 A2 2002 Size WxHxD 58cm x 16cm 30cm with bracket x 34cm Weight 11 9kg Every information is subject to change without prior notice You can download the latest version of this user manual on our website www briteq lighting com BRITEQ 8 8 CLUB LASER 7
15. ttachment fails The device should be well fixed a free swinging mounting is dangerous and may not be considered Don t cover any ventilation openings as this may result in overheating The operator has to make sure that the safety relating and machine technical installations are approved by an expert before using them for the first time The installations should be inspected every year by a skilled person to be sure that safety is still optimal CAUTION EYEDAMAGE Always position the laser in a way that prevents the audience from looking directly into the laser beams The installation should assure that the beam will not strike the audience HOW TO SET UP AND CONTROL THE UNIT Regular breaks during operation are essential to maximize the life of this device as it is not designed for continual use Do not switch the unit on and off in short time intervals as this reduces the lifetime of the lasers Always unplug the unit when it is not used for a longer time In the event of serious operating problems stop using the fixture and contact your dealer immediately Important Never look directly into the laser beam Don t use the effect in the presence of persons suffering from epilepsy ENGLISH e Link the DMX in outputs of all lasers together with proper DMX cables see drawing e The unit with no cable at the DMX input will be the master put DIP switch n 10 of the master in OFF position setting of the other DIP switches is not imp
16. ween 000 and 255 Switches 9 and 10 are used to select the desired user mode DMX OUTPUT 3pin female XLR connector used to connect the laser with the next unit in the DMX chain DMX INPUT 3pin male XLR connector used to connect universal DMX cables This input receives instructions from a DMX controller INTERNAL MICROPHONE The built in microphone is used to synchronize the laser show to the beat of the music MUSIC INPUT SENSITIVITY This potentiometer is used to adjust the music input sensitivity Turn the potentiometer until the laser works in sync with the music X Y SIZE CONTROL use these controls to adapt the size of the projected graphics to the dimensions of the venue You can change the vertical and horizontal size independently X Y MIRROR CONTROL use these controls to mirror reverse the projections This is for example useful when you project graphics from behind a transparent screen ILDA INPUT used to connect the laser to an ILDA certified interface of a computer see further for more information ILDA THROUGH to link the ILDA signal to the next Club laser 7 unit ER 24 E LASER OUTPUT Here the laser beam leaves the enclosure make sure to NEVER look inside the unit through this opening while the laser effect is switched on POWER LED indicates that the unit is switched on DMX LED indicator is lit when the laser detects a DMX signal WARNING LABEL Caution Class
Download Pdf Manuals
Related Search