Home

8000 GPRS Cradle Reference Manual_v1.05

1. Disable CHAP gt Parameter 1 Enable CHAP See Also ATDT AT APN AT DHCP AT DLMT AT PSW AT USER GPRS Back to the Supported AT Commands 35 8000 GPRS Cradle Reference Manual Read Command Response AT CLCK SC 2 lt CR gt lt CR gt lt LF gt CLCK Parameter lt CR gt lt LF gt Example AT CLCK SC 2 gt PIN authentication is disabled CLCK 0 Write Command Response AT CLCK SC Parameter PIN lt CR gt lt CR gt lt LF gt OK lt CR gt lt LF gt lt CR gt lt LF gt CME ERROR lt CR gt lt LF gt Example AT CLCK SC 1 0000 Enable PIN authentication using PIN code oK 0000 AT CLCK SC 2 gt Command syntax is incorrect CME ERROR Remarks The Read command is to get the information about whether PIN authentication is applied to the facility lock of SIM card The Write command is to set PIN authentication enable or disable Parameter is a character that determines whether PIN authentication is enabled gt Parameter 0 Disable PIN authentication gt Parameter 1 Enable PIN authentication PIN is a string for the PIN code gt PIN Personal Identity Number is a 4 8 digit access code which can be used to secure your SIM card from use If the wrong PIN is entered in more than three times the SIM card will be locked See Also AT CPIN AT CPWD SC Back to the Supported AT Commands 36 Chapter 4 Programming Your Mobile Computer Read Command Respo
2. is a character in hexadecimal with the prefix Ox For example Ox0d for Carriage Return CR See Also ATDT Back to the Supported AT Commands 40 Chapter 4 Programming Your Mobile Computer Execution Command Response AT DOWNLOAD lt CR gt lt CR gt lt LF gt OK lt CR gt lt LF gt Example AT DOWNLOAD OK Remarks This command is to upgrade firmware either downloading a user program or kernel program to the cradle After replying with the message OK the cradle will enter the Download Mode The two LEDs to the right of the front panel Tx Rx and Link will flash by turns to indicate the cradle is ready and will flash simultaneously while downloading See Also AT KVER AT VER Back to the Supported AT Commands 41 8000 GPRS Cradle Reference Manual Read Command Response AT ERR lt CR gt lt CR gt lt LF gt dddd lt CR gt lt LF gt Example AT ERR 0b00 Remarks This Read command is to get the error code for the initialization procedure dddd is the last 4 digits of the error code which is a hexadecimal number starting with Ox Refer to the Error Code table for detailed information See Also AT KVER AT VER Back to the Supported AT Commands 42 Chapter 4 Programming Your Mobile Computer Read Command Response AT IP lt CR gt lt CR gt lt LF gt IP lt CR gt lt LF gt Example AT IP The fixed IP assigned to the
3. lt gt OK message Remote hangs up NO CARRIER message 8000 GPRS Cradle Reference Manual 1 2 DIAL MODES When the mobile computer is seated in the cradle it can send the collected data back to a remote server as well as download lookup files via GSM or GPRS When dialing out ATDT the LED of Link will flash at the time interval of 0 3 seconds for about 20 seconds When connected the LED of Link will be green after successfully establishing a connection The LED of Tx Rx will flash as long as data transmission occurs Note It is suggested to issue the command AT every five seconds for best practice in order to check whether the mobile computer is seated in the cradle The escape sequence consisting of three characters is used to terminate the data connection 1 2 1 GSM CONNECTION When initialization is done issue ATDT phone number to establish data connection via GSM 1 2 2 GPRS CONNECTION When initialization is done issue ATDTxxx xxx xxx xxx kkkk or ATDT HostName Port to establish data connection via GPRS The buffer size of the cradle is 1460 bytes and data packet will be sent out as long as it satisfies any of the following requirements gt buffer is full maximum packet size is 1460 bytes gt delimiter character is encountered gt end of transmission timeout no transmission for 5 milliseconds Due to the limited memory size the cradle cannot send three pac
4. ESC to cancel ESC to exit Ver version number The current firmware version of the cradle Refer to 4 2 20 AT VER CPIN status The current PIN code status Refer to 4 2 9 AT CPIN APN access point name of ISP The current access point you are connecting to Refer to 4 2 6 AT APN CHAP status USER amp PSW The current status of Challenge Handshake Authentication Protocol CHAP Refer to 4 2 7 AT CHAP When CHAP is enabled user name and password are required DHCP amp IP The current status of DHCP server Refer to 4 2 11 AT DHCP IP address assigned to the cradle is displayed in the second line gt dynamic IP address when DHCP server is enabled gt static IP address when DHCP server is disabled 16 Chapter 2 Configuring the 8000 GPRS Cradle 2 2 CONFIGURE SETTINGS Set or modify the security setting of your SIM card When enabled PIN code is required GPRS Cradle settings configure Cradle Authentication Information 1 Authentication Current Test 2 Configure e 1 Enable 3 F w Upgrade 5 3 GPRS Settings New Default Set 1 Enable Cradle Setting Enter select Enter Confirm ESC Cancel Set or change the PIN code used for authentication PR radle Settings Configure Cradle PIN Code Information h cation S urrent Conf1igure Test 3 F w Upgrade Down load New Default Set Cradle Setting Enter Confirm ESC Cancel Ent Erase Note You mu
5. For Canada sd didas 3 Safety Preca UNS aiii ected re veweed ara ra aeea Sa Uarra tse 4 Care as Maintenance iio 4 RELEASE NOTES 0 de lacio cies 5 INTRODUC MON cuca crd sei 1 OV ENVIGW Cana e di eee eee eee 2 Installation coca a ida 3 ASSRINE SIMCald siena iria iio dsd 3 Removing SIM Card reese tect aia 3 EAU dt rod ee ee 4 inside the Packa ersin n aa aaa A a aT A iaa 4 USING THE S000 GPRS CRADLE cicis ieii lanas 5 Le Me OAA BOTA CE EE A a da 6 1 2 Dial Modas ene o a a aa ete 8 1 2 1 GSM Connection visi 8 1 22 GPRS COnnectOn A ele 8 1 3 Configuration Mode crasas a 9 13 L Gener l SOtUNES sida ali 9 1 32 Connection Settings e csser asador flan andan llana UE alli EAER A AANEREN RAN KANNEN NEARE 9 1 4 DOWNIOAd M V 00 SPE 11 CONFIGURING THE 8000 GPRS CRADLE scsdccisvecsiiesecvbecssecsnadstdecestiedelessadecascveicvsdecbeetettvstieiaaseedbernace 13 21 VIEW TNE SHINE iuris 15 2 1 1 Preview the NeW Settings ica id ria 15 2 1 2 View the Current Cradle Settings cia a a ot 16 2 2 CONTIBULE SENE ii AA 17 2 2 1 Authentication 0 id 17 2 2 2 PIN CO id 17 2 23 GPRS SOU ica ra a oo Epoca 17 2 3 DOWNIOAG SETHINES ii eb pos std 18 2 31 Download Settings nico ai oops iaa oca coa 18 2 3 2 Reset to Defaults viii acid pita 19 PE A ee eee AE 20 DA ViGPRS Testi ia 20 ZA ZIOSM TOS ci sis 21 UPGRADING FIRMWARE ca idisaconiasinaria iaa 23 PROGRAMMING YOUR MOBILE COMPUTER sitas dali 25 4 1 Programming in C LanguaBeB occcnccco
6. Reference Manual Storage Humidity Operating Storage Regulations EMC Regulations 20 C to 70 C 10 to 90 non condensing 5 to 95 non condensing CE SRMC MII 52
7. s LED will be red see LED 1 The LEDs of Tx Rx and Link will flash by turns at the time interval of 0 25 seconds for about 30 seconds indicating the cradle is in initialization process Then two conditions are encountered 1 If the LED of Tx Rx flashes it means initialization fails due to incorrect PIN 2 If the LED of Link flashes it means initialization is done successfully correct PIN or PIN not required 14 Perform echo tests if necessary 14 Chapter 2 Configuring the 8000 GPRS Cradle 2 1 VIEW THE SETTINGS 2 1 1 PREVIEW THE NEW SETTINGS In order to double check the GSM GPRS configuration you are working on information of the new settings can be previewed here Press the Up or Down key to turn pages p adle Settings PIN Enable PL information Current contigure New 3 Download APN eraut set Test 3 F w Upgrade Cradle Setting CHAP Disable CHAP Username CHAP Password UP DOWN Next Esc Exit DHCP Enable IP static 0 0 0 0 UP c PIN for authentication When enabled it means you need to provide PIN code for authentication while connecting the cradle to a GSM or GPRS network If the current and new PIN codes listed below this entry are blank you will have to input them via the Configure menu When disabled it means authentication is disabled however you still have to input the correct PIN code as the current one in use APN Name of access point that connects
8. the mobile network to the Internet For establishing a GPRS connection you will have to provide the access point name CHAP Challenge Handshake Authentication Protocol When enabled user name and password are required DHCP When enabled DHCP server is in use When disabled you will have to specify a static IP address for the cradle Note You must input the PIN code even though authentication is disabled The default PIN APN CHAP as well as IP settings should be obtained from your Internet service provider ISP or network operator 15 8000 GPRS Cradle Reference Manual You may like to find out the current cradle settings before or after configuring the cradle Such information is especially helpful when you fail to configure the cradle p adle A Settings Seat in Cradle Ver 1 03 2 3 4 Information CPIN READY Test Configure APN internet 3 F w Upgrade Download Default Set CHAP DISABLE 5 Cradle Setting USER ESC to cancel DOWN to Next PSW DHCP ENABLE IP 61 247 173 249 ESC to exit When it fails to collect information on the current settings of the cradle the LED of Tx Rx will flash to indicate the cradle is not ready A warning message is displayed along with the error code as shown below Refer to 4 3 Error Code GPRS Cradle Settings Seat in Cradle Cradle Not Ready Information Test Configure Error Code 0405 3 F w Upgrade Download Default Set Cradle Setting
9. 56 for CHAP password OK Remarks The Read command is to get the password for Challenge Handshake Authentication Protocol CHAP The Write command is to set the password for Challenge Handshake Authentication Protocol CHAP Password is a string for the CHAP password maximum 64 characters See Also AT CHAP AT USER GPRS Back to the Supported AT Commands 45 8000 GPRS Cradle Reference Manual Read Command Response AT SN lt CR gt lt CR gt lt LF gt Serial_Number lt CR gt lt LF gt Example AT SN EK8001024 Remarks This Read command is to get the serial number of the cradle Serial_ Number is a read only string that identifies the hardware See Also AT KVER AT VER Back to the Supported AT Commands 46 Chapter 4 Programming Your Mobile Computer Read Command Response AT USER lt CR gt lt CR gt lt LF gt UserName lt CR gt lt LF gt Example AT USER gt The current CHAP user name is Vodafone Vodafone Write Command Response AT USER UserName lt CR gt lt CR gt lt LF gt OK lt CR gt lt LF gt Example AT USER Vodafone gt Set Vodafone for CHAP user name OK Remarks The Read command is to get the user name for Challenge Handshake Authentication Protocol CHAP The Write command is to set the user name for Challenge Handshake Authentication Protocol CHAP UserName is a string for the CHAP user name maximum 64 characters S
10. 8000 GPRS Cradle via the Cradle IR interface 4 1 PROGRAMMING IN C LANGUAGE An example is provided below Refer to CipherLab C Programming Guide for details char a SetCommType 1 COMM_IR Set COM1 for IR open_com 1 BAUD_57600 DATA_BIT8 PARITY_NONE HANDSHAKE_NONE clear_com 1 write_com 1 AT r Send string or char to COM1 while com_eot 1 while 1 if read_com 1 void amp c read COM1 buffer data and save it in the C Note If you are programming in BASIC language make sure the default delimiter 0x0d CR is in use otherwise call COM_DELIMITER 25 8000 GPRS Cradle Reference Manual 4 2 AT COMMANDS SUPPORTED The table below lists the AT commands supported for establishing a connection via GSM or GPRS separately You may click the desired command to view details program AT Commands Description GSM Mode GPRS Mode AT Get echo from the cradle vV vV ATDT Dial out to establish a data connection via GSM V v or GPRS ATF Load factory defaults v v ATW Write the current settings to flash v v AT APN Get the Access Point Name APN currently in v use AT APN Set the Access Point Name APN you want to v connect to AT CHAP Get the Challenge Handshake Authentication v Protocol CHAP setting AT CHAP Set the Challenge Handshake Authentication v Protocol CHAP setting e
11. CipherLab Reference Manual GPRS Cradle For 8000 Series Mobile Computers Version 1 05 cier Copyright O 2008 CIPHERLAB CO LTD All rights reserved The software contains proprietary information of CIPHERLAB CO LTD it is provided under a license agreement containing restrictions on use and disclosure and is also protected by copyright law Reverse engineering of the software is prohibited Due to continued product development this information may change without notice The information and intellectual property contained herein is confidential between CIPHERLAB and the client and remains the exclusive property of CIPHERLAB CO LTD If you find any problems in the documentation please report them to us in writing CIPHERLAB does not warrant that this document is error free No part of this publication may be reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of CIPHERLAB CO LTD For product consultancy and technical support please contact your local sales representative Also you may visit our web site for more information The CipherLab logo is a registered trademark of CIPHERLAB CO LTD CIPHERLAB CO LTD Website http www cipherlab com IMPORTANT NOTICES FOR USA This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Pa
12. Cradle Reference Manual Read Command Response AT APN lt CR gt lt CR gt lt LF gt AP_Name lt CR gt lt LF gt Example AT APN gt GPRS Access Point internet is in use internet Write Command Response AT APN AP_Name lt CR gt lt CR gt lt LF gt OK lt CR gt lt LF gt Example AT APN emome Change to Access Point emome OK Remarks The Read command is to get the Access Point Name APN currently in use The Write command is to set the Access Point Name APN you want to connect to AP_Name is a string for the name of a GPRS access point maximum 128 characters See Also ATDT AT CHAP AT DHCP AT DLMT GPRS Back to the Supported AT Commands 34 Chapter 4 Programming Your Mobile Computer Read Command Response AT CHAP lt CR gt lt CR gt lt LF gt DISABLE lt CR gt lt LF gt lt CR gt lt LF gt ENABLE lt CR gt lt LF gt Example AT CHAP gt CHAP is currently disabled DISABLE Write Command Response AT CHAP Parameter lt CR gt lt CR gt lt LF gt OK lt CR gt lt LF gt lt CR gt lt LF gt ERROR lt CR gt lt LF gt Example AT CHAP 1 gt Enable CHAP successfully OK Remarks The Read command is to get the Challenge Handshake Authentication Protocol CHAP setting The Write command is to set the Challenge Handshake Authentication Protocol CHAP setting enable or disable Parameter is a character that determines whether CHAP is enabled gt Parameter 0
13. F gt CONNECT INFO lt CR gt lt LF gt ATDT HostName Port lt CR gt lt CR gt lt LF gt NO CARRIER lt CR gt lt LF gt ERR_STR lt CR gt lt LF gt ERR_CODE lt CR gt lt LF gt Example arotozeea7iies lt SUM aK a GSM data call but the remote party NO CARRIER hangs up 0x0b01 ATDT0286471166 gt Matera a call and the remote party CONNECT 9600 RE Connect to a remote host successfully via CONNECT the GPRS access point ATDT192 168 6 176 21 Cannot connect to a remote host via GPRS NO CARRIER e access point 0x8005 O E gt Connect to a remote host by host name CONNECT successfully via the GPRS access point ATDTdynamicIP xyznet org tw 20000 Cannot connect to a remote host by host NO CARRIER name via GPRS access point 0x9011 Remarks This command is to dial out for a data connection via GSM or GPRS see examples above gt If successful the response may include a string after the message CONNECT providing more information on the connection such as baud rate and so on If a connection fails the response may include a string after the message NO CARRIER 30 Chapter 4 Programming Your Mobile Computer providing further information on the connection error and it will always include a 6 digit error code Refer to the Error Code table for detailed information See Also AT DLMT GSM AT APN AT CHAP AT DHCP AT DLMT GPRS Escape Se
14. and for quick reference or maintenance purposes To avoid any improper disposal or operation please read the manual thoroughly before use Thank you for choosing CipherLab products 8000 GPRS Cradle Reference Manual OVERVIEW The cradle provides three LED indicators on the front panel to indicate connection status Refer to the flow chart for information on the initialization stages after powering on the cradle Antenna Power LED 1 TYR x Rx Link LED 2 LED 3 Power Jack SIM Card Slot Front Panel LEDs Tasks Indication of Connection Status LED 1 Power status Solid red Power ON Off Power OFF LED 2 Tx Rx status Flashing green Transmitting or receiving data Off No activity LED 3 Link status Flashing green Dialing out Solid green Connected Off Disconnected Introduction INSTALLATION 1 2 3 4 5 Screw the antenna to the cradle For initial configuration skip steps 2 and 3 Remove the rubber cover at the back of the cradle Insert your SIM card and replace the rubber cover Seat the mobile computer in the cradle Connect the power supply cord to a suitable power outlet and the cradle s LED will become red see LED 1 The cradle is ready for charging the mobile computer The SIM card orientation is as shown in the illustration above with contacts facing down Do not insert your SIM card while resetting the cradle Refer to Chapter 2 Configuring the 8000 GPRS Cradle You wi
15. ard error or no SIM card inserted Get the number of remaining PIN attempts timeout Get the number of remaining PIN attempts error Initialization procedure broken due to invalid remaining PIN attempts Set PIN for authentication timeout Set PIN for authentication failed Disable new message indication timeout Disable new message indication failure Automatically register to the home operator timeout Automatically register to the home operator failure Specify Packet Data Protocol Context timeout Specify Packet Data Protocol Context failure Attach GPRS timeout Attach GPRS failure Dialing out timeout Dialing out failure Read International Mobile Equipment Identity timeout Invalid International Mobile Equipment Identity Fatal error as disconnecting the existing call connection Query the SIM security lock state timeout Query the SIM security lock state error Negotiation with the GPRS network timeout No buffer space for link control packets Unable to transmit link control packets 49 8000 GPRS Cradle Reference Manual Ox Ox Ox Ox Ox Ox Ox Ox Ox Ox Ox Ox Ox Ox Ox Ox Ox 50 No buffer space for password authentication packets Unable to transmit password authentication packets No buffer space for IP control packets Unable to transmit IP control packets Connection terminated during link control negotiation Connection terminated during IP control negotiation CHAP authentication failure Connect to the remote IP time
16. browse the file system to locate the utility 8000DeployGPRS shx 2 Press 8 Power on the mobile computer to turn it on and access the Program Manager menu You may download the program directly to the active memory sector AC or to an empty sector and activate the program later Choose the correct interface and baud rate that match the settings on your desktop computer 3 Upon completion of the download process you will have to activate the program if it is downloaded to an empty sector 4 The utility 8000DeployGPRS shx will start itself in a few seconds 5 Go to 1 Settings gt 2 Configure to configure GPRS settings such as PIN code name of access point etc GPRS Cradle settings configure Cradle asetin 1 Information PIN Code Test J 3 F W Upgrade Down loa 3 GPRS Settings 4 Default Set 5 Cradle Setting Note You must input the correct PIN code even though authentication is disabled You can check all these settings via 1 Settings gt 1 Information GPRS Cradle Settings g Az OE 3 F w Upgrade Download 3 4 Default Set 5 Cradle Setting Go through the following steps on each cradle 6 Screw the antenna to the cradle 7 Connect the power supply cord to a suitable power outlet Note The cradle s LED will be red see LED 1 The LEDs of Tx Rx and Link will flash by turns at the time interval of 0 25 seconds for about 30 seconds indicating the cradle is in initialization
17. connects the mobile network to the Internet gt IP address DHCP or static gt User name and password may be optional depending on Challenge Handshake Authentication Protocol For quick deployment we provide a utility SHX that can be downloaded to your mobile computer and used to configure test and upgrade firmware of as many cradles as you have Refer to Chapter 2 Configuring the 8000 GPRS Cradle and Chapter 3 Upgrading Firmware Warning It is recommended that the charging devices be operated at room temperature 18 C to 25 C for optimal performance The charging devices will not charge the battery when the temperature exceeds 40 C 8000 GPRS Cradle Reference Manual 1 1 HOW IT WORKS Referring to the flow chart on the next page LED 2 and LED 3 are used to indicate a specific stage of initialization data connection as well as firmware download They are explained below by number 2 3 4 5 6 7 8 Initializing After powering on the LEDs of Tx Rx and Link will flash by turns at the time interval of 0 25 seconds for about 30 seconds indicating the cradle is in initialization process Initialization OK If initialization is done successfully the LED of Link will flash at the time interval of 1 second waiting for AT commands Initialization NG If initialization fails the LED of Tx Rx will flash at the time interval of 0 5 seconds indicating an error occurs For example it mig
18. cradle is 192 168 1 2 192 168 1 2 Write Command Response AT IP IP lt CR gt lt CR gt lt LF gt OK lt CR gt lt LF gt lt CR gt lt LF gt ERROR lt CR gt lt LF gt Example AT IP 192 168 2 100 gt Assign 192 168 2 100 to the cradle OK successfully AT IP 192 168 8 ee gt The dotted decimal notation is incorrect ERROR Remarks The Read command is to get the fixed IP address of the cradle The Write command is to set the fixed IP address of the cradle IP is a string in dot decimal for IP address xXX XXX XXX XXX See Also AT DHCP GPRS Back to the Supported AT Commands 43 8000 GPRS Cradle Reference Manual Read Command Response AT KVER lt CR gt lt CR gt lt LF gt Kernel_Version lt CR gt lt LF gt Example AT KVER Kv 1 00 Remarks This Read command is to get the firmware version of the cradle kernel program Kernel_ Version is a string that identifies the kernel it will be updated after having downloaded a different kernel program to the cradle See Also AT DOWNLOAD AT VER Back to the Supported AT Commands 44 Chapter 4 Programming Your Mobile Computer Read Command Response AT PSW lt CR gt lt CR gt lt LF gt Password lt CR gt lt LF gt Example AT PSW gt The current CHAP password is 123456 123456 Write Command Response AT PSW Password lt CR gt lt CR gt lt LF gt OK lt CR gt lt LF gt Example AT PSW 123456 gt Set 1234
19. ee Also AT CHAP AT PSW GPRS Back to the Supported AT Commands 47 8000 GPRS Cradle Reference Manual Read Command Response AT VER lt CR gt lt CR gt lt LF gt UserProgram_Version lt CR gt lt LF gt Example AT VER Ver 1 00 Remarks This Read command is to get the firmware version of user program UserProgram_Version is a string that identifies the firmware it will be updated after having downloaded a different user program to the cradle See Also AT DOWNLOAD AT KVER Back to the Supported AT Commands 48 4 3 ERROR CODE Chapter 4 Programming Your Mobile Computer The provision of error code is to assist engineers debugging the firmware Please contact your sales representative to submit your request for interpretation of an error code An error code is a 6 digit hexadecimal number always starting with Ox Refer to the Error Code table for detailed information Error Code Ox 0101 Ox 0201 Ox 0301 Ox 0401 Ox 0402 Ox 0404 Ox 0405 Ox 0501 Ox 0502 Ox 050a Ox 0601 Ox 0602 Ox 0701 Ox 0702 Ox 0801 Ox 0802 Ox 0901 Ox 0902 Ox 0a01 Ox 0202 Ox 0b01 Ox 0b02 Ox Oc01 Ox 0c02 Ox 0e0b Ox OfO1 Ox Of02 Ox 8003 Ox 8011 Ox 8012 Description GSM GPRS module failure Hardware error Disable network registration information error Get PIN PUK authentication state timeout Get PIN PUK authentication State error PUK code required to unblock the SIM card SIM c
20. gt GSM Echo Test GPRS Cradle i Echo Test Set Length 1 settings PR ho Te GS Data Length F W Upgrade Current 32 New E Dial Out setting Phone Number E Dial Out Connecting 21 8000 GPRS Cradle Reference Manual 22 Chapter 3 UPGRADING FIRMWARE The 8000 GPRS Cradle allows for firmware upgrade via the mobile computer When firmware upgrade is available download the utility 8000DeployGPRS shx to your mobile computer Warning DO NOT upgrade firmware unless the version of new firmware is greater than that of your cradle For information of the current firmware version check AT commands 1 Download the utility 8000DeployGPRS shx to your mobile computer The mobile computer will display a selection menu 2 On your mobile computer select F W Upgrade 3 Seat the mobile computer in the cradle GPRS Cradle Seat in Cradle Seat in Cradle Seat in Cradle 1 Settings 2 Test F W Version 3 F W Upgrade Current New il Firmware upgrade Press any key to OK continue Esc Exit ESC Exit Seat in Cradle Timeout Cradle not ready ESC Exit Warning Before the download process is completed do not disconnect the power to the cradle or remove the mobile computer from the cradle 23 8000 GPRS Cradle Reference Manual 24 Chapter 4 PROGRAMMING YOUR MOBILE COMPUTER You may write your own code for the mobile computer to communication with the
21. hether PIN or PUK v v code is required AT CPIN Set PIN code for authentication v v AT CPWD SC Change PIN code of SIM card v v AT DLMT Get the delimiter check status as well as the V v delimiter character if in use AT DLMT Set the delimiter check enable or disable v v AT APN Get the Access Point Name APN currently in v use 8000 GPRS Cradle Reference Manual AT APN Set the Access Point Name APN you want to v connect to AT CHAP Get the Challenge Handshake Authentication v Protocol CHAP setting AT CHAP Set the Challenge Handshake Authentication v Protocol CHAP setting enable or disable AT DHCP Get the Dynamic Host Configuration Protocol v DHCP setting AT DHCP Set the Dynamic Host Configuration Protocol v DHCP setting enable or disable AT IP Get the fixed IP address of the cradle v AT IP Set the fixed IP address of the cradle v AT PSW Get the password for Challenge Handshake v Authentication Protocol CHAP AT PSW Set the password for Challenge Handshake v Authentication Protocol CHAP AT USER Get the user name for Challenge Handshake v Authentication Protocol CHAP AT USER Set the user name for Challenge Handshake v Authentication Protocol CHAP 10 Chapter 1 Using the 8000 GPRS Cradle 1 4 DOWNLOAD MODE Regardless of the result of initialization you can issue AT DOWNLOAD to upgrade to a new fi
22. his error message is displayed due to the incorrect PIN You are required to provide the correct one while re configuring settings p radle settings Seat in Cradle Seat in Cradle fh settings 1 Information Test 2 Configure Downloading 3 F u upgrade 4 Default Set x 5 Cradle Setting ESC to cancel ESC to cancel Seat in Cradle Incorrect PIN Please check your PIN code Esc to exit 18 Chapter 2 Configuring the 8000 GPRS Cradle This error message is displayed due to PUK issue You are required to use your cellular phone to unlock the SIM card with the PUK code provided by the network operator adle Settings Seat in Cradle Seat in Cradle Information conf Downloading Test 3 F w Upgrade 3 Download Cradle setting x ESC to cancel Esc to cancel Seat in Cradle PUK required Use your cell phone to unlock SIM card ESC to exit For initial downloading or in case the cradle is malfunctioning you are advised to load the default settings to the cradle first 1 On your mobile computer go to Settings gt Default Set 2 Seat your mobile computer in the cradle PRS Cradle Settings Seat in Cradle Information T Configure Test 3 F w Upgrade Download Default Set E Reset to defaults OK Seat in Cradle Cradle Setting ESC to exit Esc to cancel 19 8000 GPRS Cradle Reference Manual 2 4 TEST You may find it necessary to test the basic fu
23. ht fail to pass PIN authentication the signal strength is weak for the GSM network the Access Point name is incorrect etc For details on the specific initialization error use AT ERR to get the error code Although initialization fails the cradle can still accept AT commands In case of the ATDT command it will re initialize before dialing out Dialing out When in Dial mode ATDT the LED of Link will flash at the time interval of 0 3 seconds for about 20 seconds Connected When in Dial mode ATDT the LED of Link will be green after successfully establishing a connection Data Transmission When in Dial mode ATDT the LED of Tx Rx will flash as long as data transmission occurs Download Ready When in Download mode AT DOWNLOAD the LEDs of Tx Rx and Link will flash by turns to indicate the cradle is ready Downloading When in Download mode AT DOWNLOAD the LEDs of Tx Rx and Link will flash simultaneously to indicate downloading is in progress Chapter 1 Using the 8000 GPRS Cradle Initialization done Initializing Powering on the cradle Dial mode Download mode ATDT Configuration mode AT DOWNLOAD Other AT commands Initialization done Re initializing GPRS Connection ATDTXxXxX XXX XXX XXX kkkk ATDT HostName Port Data transmission GSM Connection ATDT phone number Escape sequence
24. kets at the same time and therefore the third packet will be discarded We suggest you enable the Challenge Handshake Authentication Protocol CHAP setting for best practice Chapter 1 Using the 8000 GPRS Cradle 1 3 CONFIGURATION MODE Regardless of the result of initialization you can issue AT commands to configure the cradle such as gt Perform the echo test between the mobile computer and the cradle gt Write the current settings to flash or load factory defaults gt Get the hardware version Serial Number or firmware version of the cradle Set PIN authentication enable or disable Change PIN code of SIM card Send delimiter during data transmission For GPRS connection Change Access Point name apply Challenge Handshake Authentication Protocol CHAP and so on 1 3 1 GENERAL SETTINGS AT Commands Description GSM GPRS AT Get echo from the cradle v v ATF Load factory defaults v v ATW Write the current settings to flash v v AT KVER Get the firmware version of the cradle kernel v v program AT SN Get the serial number of the cradle v v AT VER Get the firmware version of the cradle user V v program 1 3 2 CONNECTION SETTINGS AT Commands Description GSM GPRS authentication is applied to the facility lock of SIM card AT CLCK SC Set PIN authentication enable or disable v v lt Parameter gt lt PIN gt AT CPIN Get the information about w
25. ll need pliers to take out your SIM card when it is not desired in use Always disconnect the power supply cord before removing the SIM card 8000 GPRS Cradle Reference Manual FEATURES Dual band EGSM900 and GSM1800 GPRS multi slot Class 10 Full PBCCH support Comply with GSM phase 2 2 Output power Class 4 2W for EGSM900 and Class 1 1W for GSM1800 Power consumption GSM connection Typical 900 mA while charging battery GPRS connection Typical 1200 mA while charging battery INSIDE THE PACKAGE The following items are included in the package Save the box and packaging material for future use in case you need to store or ship the cradle gt 8000 GPRS Cradle complete set including power adaptor and supply cord Antenna Quick Installation Guide Note This manual is included on Software amp Manual CD shipped with CipherLab 8000 Series Mobile Computers Chapter 1 USING THE 8000 GPRS CRADLE The 8000 GPRS Cradle is a charging communication cradle that is specifically designed for connecting CipherLab 8000 Series Mobile Computers to WWAN via GPRS or GSM data services Refer to Chapter 4 Programming Your Mobile Computer This chapter explains how it works and the three working modes supported by the 8000 GPRS Cradle Please contact your Internet service provider ISP or network operator for information on GPRS related settings such as gt APN name of access point that
26. nable or disable AT CLCK SC 2 Get the information about whether PIN v authentication is applied to the facility lock of SIM card AT CLCK SC Set PIN authentication enable or disable v v lt Parameter gt lt PIN gt AT CPIN Get the information about whether PIN or PUK V v code is required AT CPIN Set PIN code for authentication v v AT CPWD SC Change PIN code of SIM card v v AT DHCP Get the Dynamic Host Configuration Protocol v DHCP setting AT DHCP Set the Dynamic Host Configuration Protocol v DHCP setting enable or disable AT DLMT Get the delimiter check status as well as the y v delimiter character if in use AT DLMT Set the delimiter check enable or disable v v AT DOWNLOAD Download firmware to the cradle v v AT ERR Get the last 4 digits of error code for the V v initialization procedure AT IP Get the fixed IP address of the cradle v AT IP Set the fixed IP address of the cradle v AT KVER Get the firmware version of the cradle kernel y v 26 Chapter 4 Programming Your Mobile Computer AT PSW Get the password for Challenge Handshake v Authentication Protocol CHAP AT PSW Set the password for Challenge Handshake v Authentication Protocol CHAP AT SN Get the serial number of the cradle v AT USER Get the user name for Challenge Handshake v Authentication Protocol CHAP AT USER Set the user name for Challenge Handshake v Authentication P
27. nctionalities of the cradle Seat your mobile computer in the cradle and run the Echo Test utility on your desktop computer Note 1 Echo Test Dial Test and Dial GPRS are for internal testing 2 CMU200 Test is for manufacturing use 2 4 1 GPRS TEST On your desktop computer select TCP IP Server and change settings if necessary Then click Start x Connection Local IP Port Remote IP Action i connection 7 Connection 192168629 1024 50 E M conection Disconnected Passive Connection 1 I HEX mode Pias response time Star Clear ea senos On your mobile computer go to Test gt Echo Test gt GPRS Echo Test GPRS Cradle Testing Echo Test Set Length 1 settings 1 GPRS Echo Test 2 CMU200 Test GSM E a Data Length F W Upgrade Current 32 New E Echo Test Echo Test Server IP 235 226 0 1 Server Port 0 New 20 Chapter 2 Configuring the 8000 GPRS Cradle On your desktop computer select Modem TAPI and change settings if necessary For an external modem device select Modem COM and change settings if necessary Then click Start Ti Echo Test ver 2 03 xj Port Baud rate Action Modem COM y fi connection y COMI 115200bps Passive RS232 or IDA TAPI Modem COM l TCP IP Server TCP IP Client m sof Connection1 I HEX mode nae response time On your mobile computer go to Test gt Echo Test
28. noncnononcnnnncnnonennnnnn nn 25 4 2 Al Commands Supported nata 26 4 21 AT Command SyntAiiiiir na i aia a aaae 28 AEA I E OE E EE E e 29 ARS TD todas aan la ad oa 30 EDA n a E a 32 MD ATW A a E T A 33 A e a a a a a E 34 AD TINTA e o das ey teeta tc tase 35 ADB AVECECK HRSG vince ieee ss cased cs RR a 36 42 O a O 37 AD AO ATACPWDHSC were eee ls ee 38 e A a nye eee eee eT pe eee eigen ee 39 ADAL TADEO E IS 40 4 213 ATFDOWNLOAD iaa 41 4 2 14 AT FERR siccsscccescccssseccsscsenscceesseceedsteesccechboossauedeesceuescceedaty esseccadcceadsttecsecesscceadsebesssossssceestiene 42 4 2 15 T e 43 4 216 ATHKAVER cscccescceesseccescecescceuessceesseesaccecssoeccdues eascccesccesdsttesscedhscccedabbessscesscceedstbeasverrssccextieen 44 4 2 17 AT PSW cccccssccssscecssseecseeessnsecssneeceasessnsessneeceaseeceaesssnsessaneeseaesssneesseneessaeeesseesseneesseeessaess 45 AD AS ATES aitor alien 46 4 2 19 ATFUSER e E cnsccecestiesscesesdeecustiessceseadceceatieessecseccecsscbecsserseaceesteen 47 AD DOA TEVE ito oli idos rata 48 AS EGON Odenia cai 49 SPECIFICATIONS iia aia 51 INTRODUCTION Capable of charging the 3 7 V 700 mAh Li ion battery inside 8001 8061 8071 the 8000 GPRS Cradle is specifically designed for 8000 Series Mobile Computers to connect to WWAN via GPRS or GSM data services This manual serves to guide you through how to install configure and operate the 8000 GPRS Cradle We recommend you to keep one copy of the manual at h
29. nse AT CPIN lt CR gt lt CR gt lt LF gt CPIN READY lt CR gt lt LF gt lt CR gt lt LF gt CPIN SIM PIN lt CR gt lt LF gt lt CR gt lt LF gt CPIN SIM PUK lt CR gt lt LF gt Write Command Response AT CPIN PIN lt CR gt lt CR gt lt LF gt OK lt CR gt lt LF gt AT CPIN PUK New_PIN lt CR gt lt CR gt lt LF gt ERROR lt CR gt lt LF gt Example AT CPIN gt PIN code has already been entered lr READY successfully or the PIN authentication is disabled AT CPIN 0000 ERROR AT CPIN gt PIN code is required CPIN SIM PIN AT CPIN 0000 Enter PIN code 0000 OK AT CPIN gt PUK code is required CPIN SIM PUK AT CPIN 12345678 1111 OK Remarks The Read command is to get the information about whether PIN or PUK code is required The Write command is to set the PIN code for authentication PIN is a string for the PIN code New_PIN is a string for the new PIN code and PUK is a string for the PUK code gt PIN Personal Identity Number is a 4 8 digit access code which can be used to secure your SIM card from use If the wrong PIN is entered in more than three times the SIM card will be locked gt PUK Personal Unblocking Key is an 8 digit code used to unlock the PIN code if your SIM card is blocked Contact your service provider for PUK If the wrong PUK is entered ten times in a row the device will become permanently blocked and unrecoverable requiring a new SIM ca
30. oor use only It may do damage to the cradle when being exposed to extreme temperatures or soaked wet When the body of the cradle gets dirty use a clean and wet cloth to wipe off the dust DO NOT use mix any bleach or cleaner Always keep the cradle dry If you shall find the cradle malfunctioning write down the specific scenario and consult your local sales representative RELEASE NOTES Version Date Notes 1 05 Aug 07 2008 Modified Overview illustration updated Modified Installation illustration updated Modified 1 4 Download Mode illustration updated Modified 2 Configuring the 8000 GPRS Cradle update screenshots by adding a submenu 5 Cradle Settings to collect information on the current settings of the cradle 1 04 July 15 2008 New 2 1 2 View the Current Cradle Settings Modified Specifications Power Consumption New 4 2 3 ATDT ATDT HostName Port lt CR gt Modified 4 2 AT Commands Supported Extend the max characters allowed for AT APN AT PSW and AT USER Maximum characters allowed Before Now AT APN 20 char 128 char AT PSW 32 char 64 char AT USER 32 char 64 char 1 01 May 23 2008 gt Modified Inside the Package gt Modified section 4 2 9 Examples 1 00 Apr 25 2008 Initial release 1 03 June 24 2008 1 02 June 04 2008 yr v v v CONTENTS IMPORTANT NOTICES siiinriianaaiiniin inn Sacadecbsaancausanaddeeatdaabiacssacasessaabaaacaientcscaaaanaaee 3 For USAS ic a ai 3
31. ost Configuration Protocol DHCP setting enable or disable Parameter is a character that determines whether DHCP is enabled gt Parameter 0 Disable DHCP gt Parameter 1 Enable DHCP See Also ATDT AT APN AT CHAP AT DLMT AT IP GPRS Back to the Supported AT Commands 39 8000 GPRS Cradle Reference Manual Read Command AT DLMT lt CR gt Example AT DLMT Response lt CR gt lt LF gt ENABLE HEX lt CR gt lt LF gt lt CR gt lt LF gt DISABLE lt CR gt lt LF gt gt Delimiter check is applied and the ENABLE 0x0d AT DLMT DISABLE Write Command AT DLMT Parameter HEX lt CR gt Example AT DLMT 1 0x0a character 0x0d is currently in use gt No delimiter check Response lt CR gt lt LF gt OK lt CR gt lt LF gt lt CR gt lt LF gt ERROR lt CR gt lt LF gt Enable delimiter check successfully and OK AT DLMT 1 ERROR AT DLMT 0 OK Remarks the character Ox0a is in use gt Command syntax is incorrect gt Disable delimiter check successfully The Read command is to get the delimiter check status HEX is a character in hexadecimal with the prefix Ox The Write command is to set the delimiter check enable or disable Parameter is a character that determines whether a delimiter character is applied gt Parameter 0 Disable delimiter gt Parameter 1 Enable delimiter When Parameter 1 HEX
32. out Connection terminated while connecting to the remote IP Host name is too long DNS server is no response There is no IP information in the response message of DNS The resource type is not correct The resource class is not correct Connection terminated by the GPRS network TCP IP Connection error Disconnected by DCD line pulled high SPECIFICATIONS Processor amp Memory CPU Memory Power Adapter Input Output Power Consumption Standby Operating dial out amp transmission Peak Enclosures Materials Dimensions Weight Notifications Status Indicators Communications 16 bit CMOS low power consumption Firmware upgradeable AC 100 240 V 50 60 Hz 5V DC 225 mW 45 mA for cradle only 400 mW 80 mA when battery is charged to full 2950 mW 590 mA while charging 3400 mW 680 mA while charging with backlight on 1650 mW 330 mA when battery is charged to full 3350 mW 670 mA while charging 3850 mW 770 mA while charging with backlight on 10000 mW 2000 mA 577us ABS plastic 110 mm L x 100 mm W x 60 mm H Approx 220g 3 LEDs for connection status Data Call via GSM IP Packet via GPRS Temperature Operating Frequency bands Dual band EGSM900 and GSM1800 Compliant to GSM Phase 2 2 GPRS multi slot Class 10 GPRS mobile station Class B Transmit power Class 4 2W at EGSM 900 Class 1 1W at GSM 1800 T Y Ve y 10 C to 60 C 51 8000 GPRS Cradle
33. process Then the LED of Tx Rx will flash indicating initialization failed due to lack of SIM card Ignore it 8 Seat the mobile computer in the cradle 13 8000 GPRS Cradle Reference Manual Go to 1 Settings gt 4 Default Set to reset the cradle GPRS Cradle settings Seat in Cradle Seat in Cradle g 1 Information Test 2 Configure 3 F w Upgrade 3 Download 4 Default Set Reset to defaults 5 Cradle Setting OK ESC to cancel ESC to exit 9 Disconnect the power supply cord and insert your SIM card Refer to Inserting SIM Card 10 Re connect the power supply cord Note The cradle s LED will be red see LED 1 The LEDs of Tx Rx and Link will flash by turns at the time interval of 0 25 seconds for about 30 seconds indicating the cradle is in initialization process Then two conditions are encountered 1 If the LED of Tx Rx flashes it means initialization fails due to incorrect PIN 2 If the LED of Link flashes it means initialization is done successfully correct PIN or PIN not required 11 Go to 1 Settings gt 3 Download to download your settings to the cradles GPRS Cradle Settings Seat in Cradle Seat in Cradle Information ate Test 2 Configure Downloading 3 F W Upgrade D 4 Default Set Cradle Setting Esc to cancel ESC to cancel Seat in Cradle Download OK Esc to exit 12 Disconnect the power supply cord 13 Re connect the power supply cord Note The cradle
34. quence lt gt Back to the Supported AT Commands 31 8000 GPRS Cradle Reference Manual Execution Command Response ATF lt CR gt lt CR gt lt LF gt OK lt CR gt lt LF gt Example ATF OK Remarks This command is to load factory defaults as shown below Parameters Defaults Description unsigned char PINCode 9 0000 PIN Personal Identity Number of SIM card an access code of 4 8 digits unsigned char internet AP name for GPRS GPRSAccessPoint 21 GPRS_FLAG Flag See GPRS_FLAG structure below unsigned int Reserved 14 unsigned int DelimEnable 1 0 Enable checking the delimiter character 0 Disable 1 Enable unsigned int CHAPEnable 1 0 Challenge Handshake Authentication Protocol 0 Disable 1 Enable char CHAPPassword 33 Null Password for Challenge Handshake Authentication Protocol CHAP char CHAPUserName 33 Null User name for Challenge Handshake Authentication Protocol CHAP char DelimiterChar Ox0d Delimiter Character int DhcpEnable 1 0 Disable DHCP 1 Enable DHCP unsigned char pAddr 4 0 0 0 0 Static IP address for the cradle See Also ATW Back to the Supported AT Commands 32 Chapter 4 Programming Your Mobile Computer Execution Command Response ATW lt CR gt lt CR gt lt LF gt OK lt CR gt lt LF gt Example ATW OK Remarks This command is to write the current settings to flash See Also ATF Back to the Supported AT Commands 33 8000 GPRS
35. rd See Also AT CLCK SC AT CPWD SC Back to the Supported AT Commands 37 8000 GPRS Cradle Reference Manual Write Command Response AT CPWD SC Old_PIN New_PIN lt CR gt lt CR gt lt LF gt OK lt CR gt lt LF gt lt CR gt lt LF gt ERROR lt CR gt lt LF gt Example AT CPWD SC 0000 2008 Change PIN code 0000 to 2008 OK AT CPWD SC 2008 gt Command syntax is incorrect ERROR Remarks The Write command is to change PIN code of SIM card Old_ PIN is a string for the current PIN code and New_PIN is a string for the new PIN code gt PIN Personal Identity Number is a 4 8 digit access code which can be used to secure your SIM card from use If the wrong PIN is entered in more than three times the SIM card will be locked See Also AT CLCK SC AT CPIN Back to the Supported AT Commands 38 Chapter 4 Programming Your Mobile Computer Read Command Response AT DHCP lt CR gt lt CR gt lt LF gt ENABLE lt CR gt lt LF gt lt CR gt lt LF gt DISABLE lt CR gt lt LF gt Example AT DHCP gt DHCP is currently enabled ENABLE Write Command Response AT DHCP Parameter lt CR gt lt CR gt lt LF gt OK lt CR gt lt LF gt lt CR gt lt LF gt ERROR lt CR gt lt LF gt Example AT DHCP 0 gt Disable DHCP successfully OK Remarks The Read command is to get the Dynamic Host Configuration Protocol DHCP setting The Write command is to set t the Dynamic H
36. rmware version when available Refer to Upgrading Firmware for downloading updates via the mobile computer 1 2 3 4 5 Connect a spare 8000 cradle to your computer and make sure its baud rate is 57 600 bps If not adjust the DIP switch Connect the power supply cord of the spare cradle and the 8000 GPRS Cradle to a suitable power outlet separately Hold the spare cradle upside down so that its IR port is facing to the IR port of the 8000 GPRS Cradle as shown in the illustration Run HyperTerminal on your computer Type AT DOWNLOAD and press the ENTER key When the cradle is ready to download a new program the LEDs of Tx Rx and Link will flash by turns 11 8000 GPRS Cradle Reference Manual 6 Exit HyperTerminal 7 Run CipherLab download utility such as ProgLoad exe on your computer 8 While downloading the LEDs of Tx Rx and Link will flash simultaneously 9 The 8000 GPRS Cradle will restart itself automatically upon completion of program download 12 Chapter 2 CONFIGURING THE 8000 GPRS CRADLE For deployment engineers you can download the utility 8000DeployGPRS shx to your mobile computer and then use it to deploy a set of standard settings to the cradles as well as perform light functionality testing 1 Run one of the CipherLab download utilities on your desktop computer for example ProgLoad exe Choose the correct interface COM port baud rate file type and
37. rotocol CHAP AT VER Get the firmware version of the cradle user v program The escape sequence consisting of three v characters is used to terminate the data connection The time interval between each character should be less than one second and the guard time periods before leading and after trailing should be longer than one second separately 27 8000 GPRS Cradle Reference Manual 4 2 1 AT COMMAND SYNTAX The AT or at prefix must be set at the beginning of each command line To terminate a command line enter lt CR gt Commands are usually followed by a response that includes lt CR gt lt LF gt lt response gt lt CR gt lt LF gt gt Parameter Specify user definable parameter values which may be lt text gt or lt number gt gt ERR_STR If a connection fails the response may include a string after the message NO CARRIER providing further information on the connection error gt ERR_CODE If a connection fails the response will always include a 6 digit hexadecimal number always starting with Ox Refer to the Error Code table for detailed information Note If you are programming in BASIC language the delimiter Ox0d CR is in use by default Refer to COM_DELIMITER The escape sequence consists of three characters Once a connection has been established type the escape sequence to return to command state When entering the nex
38. rt 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures gt Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FOR CANADA This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference causing equipment standard entitled Digital Apparatus CES 003 of Indu
39. st input the correct PIN code even though authentication is disabled The access point name CHAP and IP settings should be the same as obtained from your Internet service provider ISP or network operator GPRS Cradle settings configure Cradle GPRS Settings Information 1 Authentication 1 Access Point Test Conf1igure 2 PIN Code CHAP Setting 3 F w Upgrade 5 3 GPRS Setting 3 DHCP Setting Default Set Cradle Setting 17 8000 GPRS Cradle Reference Manual 2 3 DOWNLOAD SETTINGS 2 3 1 DOWNLOAD SETTINGS After configuring settings download new connection settings to the cradle or the cradles one by one 1 On your mobile computer go to Settings gt Default Set 2 Seat your mobile computer in the cradle GPRS Cradle settings Seat in Cradle Seat in Cradle 1 Information Test 2 Configure 3 F w Upgrade 3 Download Reset to defaults 5 Cradle Setting OK ESC to cancel ESC to exit Note For initial downloading you are advised to load the default settings to the cradle first 3 On your mobile computer go to Settings gt Download 4 Seat your mobile computer in the cradle PR radle settings Seat in Cradle settings 1 Information Test 2 Configure 3 F M Upgrade 4 Default Set Seat in Cradle Downloading 3 Esc to cancel 5 Cradle Setting Esc to cancel Seat in Cradle Download OK ESC to exit Below are two common errors when it fails to download T
40. stry Canada This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Cet appareil numerique respecte les limites de bruits radioelectriques applicables aux appareils numeriques de Classe B prescrites dans la norme sur le material brouilleur Appareils Numeriques NMB 003 edictee par I l ndustrie SAFETY PRECAUTIONS RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS The use of any batteries or charging devices which are not originally sold or manufactured by CipherLab will void your warranty and may cause damage to human body or the product itself DO NOT disassemble incinerate or short circuit the battery DO NOT expose the scanner or the battery to any flammable sources For green environment issue it s important that batteries should be recycled in a proper way Under no circumstances internal components are self serviceable The charging and communication cradle uses an AC power adaptor A socket outlet shall be installed near the equipment and shall be easily accessible Make sure there is stable power supply for the mobile computer or its peripherals to operate properly CARE amp MAINTENANCE This cradle is intended for ind
41. t command after an escape sequence always wait to receive r nOK r n An escape attempt in the interval may fail because the modem is not in on line data state There are equal guard time periods before leading and after trailing The timing for this escape sequence is as illustrated below If the escape sequence is not followed by another command within 1 second trailing guard time the cradle will hang up immediately Normally the mobile computer will receive the message OK unless the line is abnormally busy Note The escape sequence will break the connection The Guard Time is 1 second and cannot be changed 28 Chapter 4 Programming Your Mobile Computer Execution Command Response AT lt CR gt lt CR gt lt LF gt OK lt CR gt lt LF gt Example AT OK Remarks This command is to do the echo test between the mobile computer and the cradle It is suggested to issue the command AT every five seconds for best practice in order to check whether the mobile computer is seated in the cradle See Also Back to the Supported AT Commands 29 8000 GPRS Cradle Reference Manual Execution Command GSM Response ATDT Phone_Number lt CR gt lt CR gt lt LF gt CONNECT INFO lt CR gt lt LF gt lt CR gt lt LF gt NO CARRIER lt CR gt lt LF gt ERR_STR lt CR gt lt LF gt ERR_CODE lt CR gt lt LF gt Execution Command GPRS Response ATDT IP Port lt CR gt lt CR gt lt L

8000 GPRS Cradle Reference Manual_v1.05

Contents

Download Pdf Manuals

Related Search

Related Contents