TPMS1209T07 User Manual - Tire Pressure Monitoring System
Contents
1. as shown below 5 Press the key to access the fifth interface 33 stands for 33 min As shown below Under any interface of system time inquiry press S for 3 seconds to start programming For example change the year to 09 under the year interface press S for 3 seconds the second digit flashes press up or down key arrow key to adjust the value Then press key the third number flashes then press up or down arrow key to adjust the value to 9 At last press S for 3 seconds to save the change with screen flashes twice and beep buzzes twice Then it automatically switches to next interface Month for programming 2 4 Programming of Temperature and Pressure Unit 1 After programming time press P to access interface for programming temperature and pressure unit it first enters the temperature unit interface At this time press up or down arrow key can switch to pressure unit displaying interface as shown below Note Under this interface the PSI unit is flashing which indicates the currently set unit 17 2 Under any above interface press S for 3 seconds to program For example change the temperature unit under the interface displaying temperature unit press S for 3 seconds and the units C and UNIT start flashing as shown below Press up or down arrow key to choose temperature unit which will flash the UNIT will flash all the time indicating that th2. Above figure shows that the first and second tire position icons disappear this indicates that the ID of these two tire transmitters have been programmed and saved by the monitor Under the deletion of transmitter ID interface the user can inquire the details of the two tires 12 The third and fourth tire position icons are shown by black solid icons which indicate that ID of the two tire transmitters have been programmed The sixth tire icon continues to flash in the figure indicating that the tire transmitter is being programmed The rest hollow tire icons indicate that ID of them have not been programmed 2 2 Standard Pressure Programming For example set the standard pressure of first tire position to 105psi1 1 When finish programming ID press P to access the standard pressure programming mode 2 Then press any of the four arrow keys to choose the desired tire position to program 3 Then press S for 3 seconds to set the first digit which flashes Press up or down arrow key to adjust the value 4 Once finished programming the first digit press to program the second digit which flashes and then press up or down arrow key to adjust the value 13 5 Once finished programming the second digit press to program the third digit which flashes and then press up or down arrow key to adjust the value to 5 6 Below example shows that the first second and third tire position icons are shown in bla
3. 28 1 Full time Monitoring 28 2 High Pressure Alarm 2 22222000 0222222200 28 3 Low pressure level 1 alarm 29 4 Low pressure level 2 alarm 29 5 High Temperature Alarm 30 6 Quick Leak Alarm 31 7 Transmitter Trouble Alarm 31 VI Specifications 2 2 2 2222222 e een n nnn n eee e eee n nnn n nen 32 VII Frequently Asked Questions 33 VIII Warranty Term 2 35 IX Important Notes 2 2222222200022 e nee eeeeeeeeee 36 I TPMS1209T07 FULL TIME DIRECT TPMS TPMS1209T07 is direct tire pressure monitoring system for engineering machinery which includes 1 monitor 1 standard booster optional and transmitter can support monitoring of up to 38 tires The transmitter can be screwed onto the tire to replace the original valve cap and then senses the tire pressure all the time and transmits the pressure information data to monitor by RF tec
4. standard pressure and the default standard pressure is set to 100 psi in factory 4 Make sure the monitor is in the normal mode not in the programming menu mode For example ID programming or standard pressure programming otherwise monitor can not receive information from the transmitter When use the system for first time the normal operating mode is as shown below 23 5 During the installation of transmitter the monitor must be in working mode otherwise monitor can not receive information from the transmitter 6 During installation of transmitter monitor can only receive information from one transmitter each time Therefore please check if the monitor has receive information of previously installed transmitter then continue to install another one The operation steps are as follows 1 Remove the current tire valve cap 2 Inflate the tire to the standard pressure recommended by the manufacturer or pressure needed by the user 3 Check whether the rubber seal is smoothly placed inside the transmitter s copper insert 24 4 Screw the locknut onto the screw thread of the tire valve 5 Screw the transmitter onto the tire valve and then fix the transmitter by screwing the locknut inversely 6 Check the connection of transmitter and valve with the soap solution to confirm whether the transmitter is firmly screwed onto the valve or not check whether there is air leakage caused by the installatio
5. Periodic check of the tire can keep the driver aware of the tires conditions and ensure driving safety 2 Pressure alarm frequently occurs The user can check if the standard pressure is suitable or not If the standard pressure is too high or too low re set the standard pressure according to the page 13 of USER MANUAL 3 How long can the transmitter battery work The transmitter battery can last about 5 years under normal conditions 4 How to deal with the transmitter trouble alarm issued by monitor If one transmitter fails to work or the monitor cannot receive the signal for 20 minutes because of the RF interference the system will issue a transmitter trouble alarm Once there is no interference the system shall recover normal performance 5 Why the temperature sensed by the transmitter is quite different from the actual value The temperature sensed by the transmitter is the environment temperature not that inside the tire When vehicle runs the temperature around the transmitter will rise When there is high temperature alarm please check if the tire 1s under abnormal condition which causes the 33 wheel rim becomes very hot 6 The monitor displays nothing or abnormal code Please check the power supply and wire connection 7 When connected with vehicle s continuous power supply will the power of storage battery be used up if the vehicle parks for a long period The current draw of the monitor is about 100 mA under normal
6. TPMS1209T07 USER MANUAL Suzhou Sate Auto Electronic Co Ltd www sate com cn Table of Contents I TPMS1209T07 Full time Direct TPMS 3 II Parts of TPMS12091T07 4 III Installation and Programming of TPMS1209T07 Monitor 5 1 Installation of Monitor 5 2 Programming of Monitor 9 2 1 Programming of Transmitter ID 9 2 2 Standard Pressure Programmin 13 2 3 System Time Programming 15 2 4 Programming of Temperature and Pressure Unit 17 2 5 Deletion of Transmitter ID 19 2 6 Alarm Record Inquiry 19 2 7 Upload pressure log and alarm records 21 2 8 Exit of System Menu 23 IV Installation of TPMS1209T07 Transmitter 23 Installation of Transmitter 23 V System Function of TPMS1209T07
7. ck solid which indicate that ID of the three tire transmitters have been programmed Tire icon in the red aperture continues to flash indicating that the position is being programmed with standard pressure The rest hollow tire icons indicate that ID of them has not been programmed Note 1 Under this interface tire icon with transmitter ID programmed will be in black solid The standard pressure makes sense only when the tire transmitter ID has been programmed Therefore if the icon is solid black it only has relation with whether the ID is programmed or not 2 The default standard pressure is set to 100 psi in factory 3 38 tire positions are always shown in this mode If this is the first time for the user to use the system please inquire IV Installation of Transmitter directly to finish the first installation 2 3 System Time Programming Function The system clock was preset in the factory It 1s the base of the alarm record user can check the current date and time as follows 1 When finished programming the standard pressure press P to access interface for inquiry and programming of time date the first interface displays the year 08 stands for the year 2008 2 Press key to access the second interface 02 stands for February as shown below 3 Press the key to access the third interface 28 stands for 28 day as shown below 4 Press the T key to access the fourth interface stands for 9 O clock
8. e present interface is not the inquiry but the programming interface as shown below Then press S for 3 seconds to save with beep buzzes twice All the icons will stop flashing and only the selected unit is displayed 2 5 Deletion of transmitter ID 1 When finish programming temperature and pressure unit press P to access the transmitter deletion interface Only the programmed and matched transmitter will be shown with solid wheel icon and only the last 3 ID digits will be shown 2 Press any of the four arrow keys to locate the wheel position to be deleted 3 Press S for 3 seconds to delete with the screen flashes twice and beep buzzes twice to confirm the deletion Then it automatically switches to next transmitter location 2 6 Alarm Record Inquiry 1 Under normal mode or pressure inquiry interface press P and S at the same time for 3 seconds to access the alarm record inquiry interface The screen with 0 is the first and most recent alarm record as shown below 2 Press key to check through the record If there 1s no operation within 3 seconds it will automatically display the record data pressure temperature and time in turn Pressure Temperature Time year Time month 20 Time date Time hour Time minute Then it will display the next alarm record in the same way as above 3 Press P and S at the same time to return to pressure inquiry interface 2 7 U
9. hnology The monitor can receive and deal with the data then display the pressure on the screen The monitor can issue different alarms if the tire pressure is at an improper level based on the standard pressure so as to notify the driver to treat the problem Through TPMS1209T07 the driver can keep the tire running under a proper pressure so as to avoid excess gasoline consumption and keep the vehicle in an easily controlled state II Parts of TPMS1209T07 1 Monitor Direction Direction Direction Direction Mounting key f key gt key key lt bracket Screen Display O Pressure Transmitter Pressure unit BAR trouble alarm alarm icon icon 2 Parts of transmitter HI Installation and Programming of TPMS1209T07 Monitor 1 Installation of Monitor 1 1 Take out monitor and bracket from the package 1 2 Insert the bracket to the back of the monitor as shown in below picture to fix the monitor 1 3 Take out a pair of 3M Dual Lock Fastener and separate them 1 4 Fasten the 2 pcs fasteners with those on the monitor bottom 1 5 Choose a suitable location to install the Monitor on the dashboard Make sure to first scrub the installing position with alcohol 1 6 Strip off the liner of the 3M Dual Lock Fastener 1 7 Fix the Monitor onto the cleaned position make sure to fix the bracket firmly 1 8 Connect power wire to the vehicle s power supply The anode of the monitor po
10. inform us in case that the telephone number or address on the Warrant Card is changed 3 The warranty responsibility is subject to the conditions and limitations specified in the User Manual 4 The monitor should be connected with the continuous power supply and installed by the professional We are not responsible for the vehicle circuit damage or accident caused by wrong installation or improper use of the system 5 This TPMS system can perform full time monitoring function but cannot avoid all unexpected accidents 36
11. n or the seal of the transmitters or not 7 Once screwed onto the tire transmitter can sense the pressure inside the tire and transmit the data to the monitor and the information will appear on the screen within about 6 minutes Check the Monitor After install the first transmitter please check the monitor If the pressure and temperature of the installed transmitter are in normal mode the screen will display as shown below If the monitor alarms please refer to V System Function to eliminate tire alarm The first transmitter ID has been Tire pressure and temperature are in normal level If the above figure is displayed it indicates that the transmitter is installed correctly and the user can install the next one When all the transmitters have been installed correctly screen will display as shown below Note Number of transmitters and installing positions may differ in actual applications 6 transmitter ID have been received by the monitor and all the pressure and temperature are in normal mode then press or P screen will display as shown below 26 Then the screen will access the mode which show each tire s pressure and temperature from the 1 tire position Black solid icon indicates the tire information is being displayed Press or to inquire each tire s pressure and temperature manually Under any tire position press S key to inquire tire temperature Pre
12. ow down and adopt measure to cool down the tire The red alarm lamp goes off automatically when the temperature returns to normal level 30 6 Quick Leak Alarm Display mode Function The system will issue a fast leak alarm when the pressure drops more than 0 20BAR within 12 seconds Alarm mode The alarm lamp flashes and the audible alarm turns on the tire position icon flashes Treatment Press any key to stop the audible alarm and the system reverts to normal mode Then slow down and check the correspondent tire 7 Transmitter Trouble Alarm Display mode Function If one transmitter fails to work or the monitor cannot receive the data because of the RF interference for 20 minutes the system will issue a transmitter trouble alarm Alarm mode The audible alarm turns on the red alarm lamp flashes and transmitter trouble alarm icon appears Treatment Press any key to stop the audible alarm Then the system reverts to the normal mode Note The red alarm lamp goes off automatically when the communication between the transmitter and monitor returns back the normal mode VI Specifications Monitor Modulation Type FSK Mid frequency Receiving Sensitivity Input Voltage Operating Temperature Storage Temperature Wee Transmitter Modulation Type FSK Mid frequency input Voltage 32 VII Frequently Asked Questions 1 Why do I need to check the tires periodically with the TPMS system installed
13. pload pressure log and alarm records The product can save tire information and the recent 180 pieces of alarm records automatically when the system is operating In addition the monitor can record the pressure data of the transmitters every 30 21 minutes within the recent half year The user can upload the data in the computer by USB RS232 When insert the USB cable screen will display as shown below Now system is in the mode waiting for information uploading and all the buttons can not be used until the USB cable is pulled out Connect the other end of the USB cable to computer and then open the Monitor Log receiving software in the computer Click the upload button of the software monitor will upload the data as shown below Black solid icon will continue to move to indicate the data is being transmitted If transmission is paused or finished screen will revert to the mode before transfer If pull out USB cable screen will revert to the mode before insert USB cable Please refer to Monitor Log User Manual for more details 2 8 Exit of System Menu Under system programming mode press P key for 3 seconds to return to normal mode IV Installation of TPMS1209T07 Transmitter Installation of Transmitter Before install the transmitter 1 Make sure the monitor is powered and operating normally 2 Make sure the transmitter to be installed has been programmed into the monitor 3 Program each tire s
14. s the programming mode the first interface is for ID programming as shown below 2 Press any of the four arrow keys to choose the transmitter position which needs to be programmed 3 Then press S for 3 seconds to start programming and the first digit flashes then press up or down arrow key to adjust the value 4 Once finish programming of the first digit press to start programming the second digit which flashes Press up or down arrow key to adjust the value 5 Press again to program the third digit which flashes Press up or down arrow key to adjust the value 6 When finish programming these 3 digits press S for 3 seconds to save with the screen flashes twice beep buzzes twice Then it will automatically switch to next tire position 7 Follow the above operations to program ID of other transmitters 11 Note The tire position with ID programmed will be shown in solid black icon and the tire position being programmed will continue to flash There are 38 tire position icons in this interface The method to sequence tire position 1s increasing from the top down from left to right as shown below 4 3 2 gt 5 6 38 If tire position icon shows nothing it indicates that ID of the tire transmitter has been programmed and saved by the monitor If the user wants to inquire the details of the tire position please refer to Deletion of transmitter ID for more details
15. ss S key again to return to ON interface If all the pressure and temperature are in normal level Note 1 After installed one transmitter but the monitor can not receive the information from it please remove the transmitter and install it again according to IV Installation of Transmitter 2 If one of your transmitters is broken or lost the user only needs to replace this one the others will work normally V System Function of TPMS1209T07 1 Full time Monitoring Function TPMS1209T07 can monitor the tire pressure and temperature whether the vehicle is running or parked Therefore to keep the driver informed of the tire state and realize full time monitoring 2 High Pressure Alarm Display mode Function The system will issue the high pressure alarm when the tire pressure 1s 25 higher than the standard pressure Alarm mode The alarm lamp flashes high pressure warning icon tire position icon and the audible alarm turn on together Treatment Press any key to stop the audible alarm The red alarm lamp remains on and the display reverts to the normal mode At this time user should adjust the tire pressure to the normal level with proper method The red alarm lamp goes off only when the tire pressure returns to the normal level 28 3 Low pressure level 1 alarm Display mode Function The system will issue level 1 low pressure alarm when the tire pressure is 10 lower than the standard pre
16. ssure Alarm mode The alarm lamp flashes low pressure level 1 alarm icon tire position icon and the audible alarm turn on together Treatment Press any key to stop the audible alarm The red alarm lamp remains on and the display reverts to the normal mode At this time the user should inflate the tire to proper air level as soon as possible The red alarm lamp goes off only when the tire pressure returns to normal level 4 Low pressure level 2 alarm Display mode Function The system will issue level 2 low pressure alarm when the tire pressure is 15 lower than the standard pressure Alarm mode The alarm lamp flashes low pressure level 2 alarm icon tire position icon and the audible alarm turn on together Treatment Press any key to stop the audible alarm The red alarm lamp remains on and the display reverts to the normal mode The user should slow down the vehicle and drive to service shop to inflate the tire The red alarm lamp goes off only when the tire pressure returns to normal level 5 High Temperature Alarm Display Mode Function When the temperature around the transmitter equals or exceeds 90 C the system will issue the high temperature alarm Alarm Mode The alarm lamp and temperature value flashes tire position icon and the audible alarm turn on together Treatment Press any key to stop the audible alarm The red alarm lamp remains on and the display reverts to the normal mode The driver should sl
17. state and this can be ignored However if the vehicle will not be used for 2 or 3 months the storage battery might be used up and the vehicle cannot be started So we suggest the user remove the storage battery if the vehicle will not be used for a long period 34 VIII Warranty Terms Valid Warranty Card 1 The Warranty Card must be filled completely signed by and sealed by the authorized distributors 2 The Warranty Card is valid in the countries or regions where the purchase occurs 3 The Warranty Service requires user to offer the Warranty Card and the original invoice Warranty Condition Responsibility and Limitation 1 The product warranty period is one year and is subject to the time marked on the invoice 2 Any damages or faults due to improper use are not involved in the warranty commitment 3 Users are not allowed to open repair and refit the products by themselves otherwise the warranty service will be invalid 4 Injecting chemicals such as leak proof glue into the tire will damage the Transmitters and affect the system operation Do not use such articles after the TPMS is installed 5 The warranty does not include replacement of the enclosure and display panel 6 The warranty does not cover the product damage due to abrasion and Corrosion 35 IX Important Notes 1 The Warranty Card must be filled completely and its number shall be quoted whenever the user requires the service 2 Please
18. wer wire should be connected to anode 12 24V power of the vehicle s continuous power supply The cathode should be grounded L The monitor power wire No Color Electric Note The red and blue wire should be together connected to the anode 8 and the black wire to the cathode Make sure wires are well connected The red and blue ori Na FERN Screen Display The monitor starts to work after it is powered At this time the monitor cannot receive any information as the transmitters are not installed The screen shows NSP No Transmitters Programmed which means monitor is waiting for receiving the signal 2 Programming of Monitor 2 1 Programming of Transmitter ID Before install the transmitter the user has to program last 3 digits of the ID into the tire position shown on monitor screen Then after screw on the transmitter it will sense and transmit tire pressure information to the monitor The monitor will save the information automatically after received the ID and display the pressure and temperature data on the screen Then the transmitters are programmed and matched Each transmitter has 4 groups of ID for example when program the transmitter with ID of 001 001 001 158 to front right tire position the user only needs to input the last 3 digits 158 Steps are as follows last 3 digits of ID 1 Under any interface of the normal mode press P key for 3 seconds to acces
Download Pdf Manuals
Related Search