User Manual
Contents
1. then be sure to Keep battery well away from flammables 2 meters or more Contain battery in a heavy fireproof container such as a brick box Always monitor the charge HYPERION ACCEPTS NO RESPONSIBILITY FOR DAMAGE OR INJ URY during INDOOR or other HIGH RISK CHARGING ACTIVITY Initial Setup The EOS 0606i requires 4mm Bullet Connectors aka Banana Plugs on 12awg wire leads for output harness between charger and battery main wires Harness wire leads should never exceed 20cm in length Pre assembled output harnesses are available under Hyperion Part HP EOSOUTCORD and one harness is included with each charger Solder your chosen battery side connector to the bare wire ends of the harness taking great care to observe proper polarity If after carefully reading the following pages on usage you have any difficulty using the charger please refer to the final pages for troubleshooting guide and warranty terms It is well to carefully check your charger before making a return as problems in setup cabling or power supply are much more common than defects in the charger Chargers returned by the user and later found not defective will only be returned to the user at the user s expense and may incur a service charge ALWAYS FOLLOW this connection sequence and reverse sequence to disconnect 1 Connect OUTPUT harness 4mm plugs to the sockets located on the right side of the charger Take care that the Output Harness RED wire bullet connect2. dropping on the floor etc inappropriate power supply automotive battery charger etc water moisture and humidity are specifically NOT covered by warranty Damage due to short circuit of live Positive Output lead to Charger Case is NOT covered so be careful with exposed connectors It is well to carefully check your charger before making a return as problems in setup cabling or power supply are much more common than defects in the charger Enjoy the Power The Hyperion Team
3. the Enter button Press BATT TYPE during charging or discharging to view the data display menu Use INC and DEC to scroll through the data screens Pressing BATT TYPE again will return you to the charge discharge screen Data Display Screens Example During a Balancer Connected Lithium Charge ENTER ERROR MESSAGES INPUT VOLTAGE ERROR Input voltage is below 11 0V or exceeds 15 0V NO BATTERY Battery not detected OUTPUT BATT REVERSE POLARITY Battery is connected in reverse polarity to Output leads OUTPUT CIRCUIT PROBLEM Non Specific Circuit error Check battery condition CHECK BATT OPEN CIRCUIT Battery disconnected during charging CHECK BATT OVER VOLTAGE Battery voltage too high to match charger settings CHECK BATT LOW VOLTAGE Battery voltage too low to match charger settings BALANCER VOLTAGE TOO HIGH If voltage per cell is too high during balancing this message may appear BALANCER VOLTAGE TOO LOW If cell s voltage falls too low during balancing this message may appear DON T CHARGE Lixx WITH THIS MODE A Lithium pack is connected by balancer but NiCd NiMH Pb mode is selected for charging Note If the incorrect number of cells is selected for a lithium type battery and charging is begun the charger may give error immediately and stop charging In some cases however the charger will begin charging at the lower voltage it sees as correct and watch all cells to confirm the in
4. ERION type adapter board but will not charge properly Check this list below If your pack is either Hyperion or XH type select the correct adapter from the two supplied with the charger Otherwise you will need to order the correct option adapter EH TP FP or CellPro for your pack IF YOUR PACK MAKER IS NOT LISTED BELOW ASK THE MAKER WHICH BRAND BELOW IT MATCHES HP EOSLBA 26XH B HP EOSLBA 26HP B HP EOSLBA 26TP B HP EOSLBA 26EH B ALIGN HYPERION THUNDER POWER KOKAM DUALSKY POLYQUEST FLIGHTPOWER EVO GRAUPNER E FLIGHT E TEC APEX ROBBE ELECTRIFLY POLY RC VISLERO NEU HEXTRONIC XCITE DANLIONS APOGEE COMMON SENSE V1 MAX AMPS MPX VAMPOWER COMMON SENSE V2 TRUE RC ESKY IMPULSE VENOM AIR THUNDER KONG THUNDER GRAYSON POWER TENERGY DN POWER MEGA POWER ELECTRIC POWER TURBORIX ENERGY EC WOW RC IMAX FULLY MAX FUSION CONNECTOR WIRING FOR HYPERION and COMPATIBLE PACKS BATTERY 5 pin BATTERY 5S 6 pin BATTERY 8 pin 3S 5 pin 7 pin 4S j 5 pin 75 6S WARRANTY HYPERION Chargers are guaranteed to be free from defects in materials and workmanship for a period of one calendar year from date of purchase Your selling dealer is your first point of contact for warranty issues Return postage costs are the responsibility of the user in all cases You MUST Submit a copy of original receipt with the return Damage due physical shock
5. HYPERION AC DC EOSO606iAD C USER S MANUAL Visit http media hyperion hk dn eos for the newest manuals and news EOS 0606i AC DC Special Features rev C Use AC 100V 240V at home OR DC 11V 15V anywhere Powerful yet compact and portable with wide support for battery types ntegrated Hyperion LBA Balancer for LiPo 3 7v and LiFe 3 3v based cells Balance Multi Adapters for 2S 6S packs inc Hyperion and XH Types Charge Discharge and STORAGE Modes and Cycling for NiMh and NiCd Clear Yellow Backlit LCD Screen Warnings for common setup errors Packaged in a rugged case with Long Input leads Option multi connectors for common pack brands are also available see details end of document Specifications 11 0 15 0V DC OR 100 240V AC at 50 60 Hz Input voltage range Only ONE source may be connected at a time 1 14 NiCd Nickel Cadmium cells 1 14 NiMH Nickel Metal Hydride cells 1 6 LiPo Lithium Polymer cells 100 20 000mAh 3 7V cell type only Appropriate battery types and range of series connected cells 1 6 LiFe Lithium Iron 3 3V cell types inc A123 brand cells LiFePO4 cells 1 6 Lead Acid cells 2V per cell nominal 0 1A 6 0A MAX by 50mA steps for Lipo and LiFePO4 100mA steps for NiCdd NiMH and Lead Acid 50W limit Discharge current 0 1A 1 0A MAX by 10mA steps 5W limit Trickle charge current NiCd NiMH 0 200mA Delta V peak detection for NiCd
6. NiMH CV CC for Lithium and Lead Acid Batteries Cycling Modes NiCd NiMH Charge gt Discharge or Discharge gt Charge Charge current Charge termination Display type 2 line 16 character high visibility yellow backlit LCD Safety precautions e KEEP CHARGER and BATTERIES AWAY FROM CHILDREN AND PETS AT ALL TIMES e This charger is ONLY for NiCd NiMH Lithium 3 7V cell A123 3 3V cell and Lead Acid 2 0V cell type cells DO NOT connect others such as 3 6V cell Lithium Ion or non rechargeable batteries e Always place the charger on a firm level and fireproof surface for charging Do not place the battery or charger on or near flammable materials while in use Keep away from carpets cluttered workbenches etc Do not exceed cell manufacturer s suggested max charge rates Do not use automotive type battery chargers to power the charger Do not leave the charger unattended while charging Do not allow water moisture or foreign objects into the charger Do not open the charger nor attempt any repair as it is dangerous and will void your warranty Do not obstruct the air intake or outlet holes on the charger ALWAYS follow correct connection sequence as given below CAREFULLY FOLLOW THE BATTERY PACK MAKER S RECOMMENDATIONS AND SAFETY ADVICE HIGH RISK CHARGING ADVISORY Avoid charging batteries indoors If you must charge indoors or any place injury to persons or damage could result in the event of fire
7. correct setting For example if you connect a 3S pack but set the charger for 4S by mistake the charger may begin by charging at 3S voltage level and watch all cells When the mistake is confirmed the charger will give error and terminate This is normal and correct behavior TROUBLESHOOTING 1 Check again that the battery you are trying to charge and the settings on the EOS 0606i match Battery type such as NiMH or Lithium battery capacity number of cells charge voltage and charge rate must all be correct 2 Check that the input cable and output cables Have proper connectors in good condition Are not frayed worn cut or damaged Are the proper gauge 2 5mm 14ga or higher Are proper length 20cm 8 on output side 3 Attach the charger input connectors to a 12V automotive battery that is in good condition and fully charged Wiggle the Terminal clips into the battery posts to insure that you have a good connection Try the AC input if failing while using DC 4 Try another battery for charging If your RC battery is in poor condition over discharged or in some other way defective the charger may correctly refuse to charge it based on safety algorithms 5 Try another RC battery type For example switch to a NiMH battery if you are failing to charge Lithium types Success with one type but failure with another generally indicates that the charger is working properly The failing battery type is almost certainly in poor co
8. djust and set the correct battery capacity from 100mAh to 20000mAh with INC amp DEC buttons 50mAh per step Press the ENTER button to confirm setting Charge rate is set on the basis of selected capacity at 1C rate Example Li Po cell of 1500mAh capacity 1C 1500mA 1 5A Setting Battery Voltage Number of Cells in Series for LiPo Life battery packs Select the total battery voltage in S to be charged with ENTER INC amp DEC buttons Setting Charge Rate Amps By default this field will be filled out with a 1C charge rate based on the capacity of your pack set previously If you do not know the manufacturers max allowed charge rate do not change this default setting Capacity mAh 1000 Ah so a 2100 mAh pack at 1C 2 1A 2C 2 4 lt A etc Setting discharge parameters Adjust to the desired discharge current from 0 10A to 1 00A 0 01A per step with INC amp DEC button Press the ENTER button to confirm setting Set pack voltage 1S 6S as in charging example above Autocut occurs automatically at 3 5V per cell for Lipo and 2 9V for LiFe We do NOT recommend using the lithium discharge function unless you have a very compelling reason and you are an advanced user Use only STORE MODE if you want to store your pack LiFe MODE LiFePO4 A123 The LiFe LiFePO4 charge discharge modes are intended for cells with 3 3V nominal produced by Hyperion A123 Company or other brand LiFePO4 cells which are recognized to be of good
9. iMH mode is the same as below except Mode shows NiMH Delta V Defaults and minimum values are NiCd 5mV cell NiMH 3mV cell In most cases these should be left alone Advanced users may wish to increase settings to archive a delayed charge termination but if set to high can result in over charge and could therefore be dangerous Trickle charge maintains a NiCd NiMH battery charge until the battery is removed Trickle rate depends on charge current setting and ranges from 50mA to 200mA If charge current is lt 1A there is no trickle You can turn trickle such that it is always OFF as shown above Displays during Charge Discharge and Cycle Note that exact display may depend on type of battery and connection For example Lithium types when connected to a balancer will alternately show CHG BLC at top left while charging and CHG BLC END when finished charging Also note that after charging the EOSO606i may apply maintenance current or discharge as needed to maintain balance until disconnected CHG charge DCH discharge C D cycle D gt C cycle NC NiCd NM NiMH LP LiPo LF LiFe Pb Lead Acid Completion Display Time Delay in minutes between Charging and Discharging or Discharging and Charging Time in minutes sec Capacity in mAh When the Enter button is pressed charge or discharge will be stopped In order to move back to the main display press
10. n to confirm setting E Setting total battery voltage for Lead Acid Battery Select the proper total battery voltage to be charged or discharged with INC amp DEC buttons 2V 4V 6V 8V 10V and 12V 2V per cell types only Setting discharge current Adjust and find the desired discharge current from 0 10A to 1 00A 0 01A per step with INC amp DEC button Press the ENTER button to confirm setting NiCd NiMH OPERATION MODES NiMH mode is the same as below except Mode shows NiMH BATT TYPE NiCd Setting charge current Adjust and find the desired charge current which ranges from 0 1A to 6 0A with INC amp DEC buttons Press the ENTER button to confirm setting Setting discharge current Adjust and find the desired discharge current ranging from 0 1A to 1A with INC amp DEC buttons Press the ENTER button to confirm setting The 5W max may reduce the current you set depending on the voltage of your battery pack Setting discharge cutoff voltage This is the voltage that the charger should stop discharging the battery Adjust and find total discharge cutoff voltages to be discharged from 0 1V to 16 8V with INC amp DEC buttons Press the ENTER button to confirm setting Setting cycle This is to set cycling with two options Charge to Discharge Discharge to Charge Set cycling with INC amp DEC buttons and press the ENTER button to confirm setting Setting Delta V and Trickle Options for NiCd NiMH N
11. ndition then or you have improperly set the charger for it 6 My LCD does not light or lights but no characters are visible In most cases this happens when a charger has been dropped or suffered some heavy vibration The ribbon cable between LCD unit and charger can become loose Have your dealer open the charger and re seat the ribbon cable 7 Contact your dealer with full details and description of the problem including the type of input power source RC battery type and cell count and history of the charger specifically has the charger been working properly before or failing from new condition 8 have an OUTPUT CIRCUIT ERROR Be sure that your pack balance connector type polarity and wiring system matches the multi adapter attached to the charger Carefully inspect pack connector balance wire harness and Multi Adapter for damage wear etc If OK then Spray all connectors including the one in charger with de oxide contact spray then insert remove connectors several times then spray one last time and re connect Use a solid DC PS or fully charged CAR battery for Input power poor power supplies cause MANY problems Test charger using a lithium battery known to be in good condition Try a different brand battery preferably with different balance connector and multi adapter type NOTE Many problem are from using the wrong balance adapter For example XH type packs such as Align will fit in the HYP
12. or goes to the socket and BLACK wire to 2a Connect Charger INPUT alligator clips to an appropriate DC power source a A 12V automobile battery b A quality low noise DC power supply of 12 15V with 5A rating large batteries may require 10A supply OR 2b Connect to AC wall power 100 240V using the supplied AC cable DO NOT CONNECT BOTH AC AND DC INPUT AT THE SAME TI ME The Charger will display INPUT VOLTAGE error message if input voltage is out of range If this happens please recheck the input power supply to make sure correct voltage of 11V to 15V is present The INC and DEC buttons are also used to select MODE such as Charge Discharge Store or Cycle The BATT TYPE and ENTER buttons both have two modes SHORT press or LONG 1 second press e Short press BATT TYPE Scroll battery types NiCd gt NiMH gt LiPo gt LiFe gt Pb e Long press BATT TYPE View input output Data e Short press ENTER Scroll settings for a battery type Values will blink when selected Blinking will stop after a few seconds if you do not make a change Short press Enter to re select a setting to change Short press BATT TYPE to re select Battery Type then INC DEC to change values e Long press ENTER START STOP charging or discharging or cycling etc 3 Set the battery type using the charger configuration buttons The INC and DEC buttons are used to Increase or Decrease values such as Charge Current or Cell Count Let s start b
13. quality from well known makers Choose LIFE for BATT TYPE for charging such cells Due to the nature of A123 LiFePO4 cells wide divergence in cell voltages during charging and due to the high rates at which some of these cells can be charged one MUST ALWAYS properly use the cell balancer function whenever charging in LiFe Mode failure to do so will result in poor pack performance at best and damage to cells at worst Customers who charge in LiFe mode without balancer connected assume all risk of charger and battery failure Number of LiFe Cells Wired in Series Pack Voltage 1S 2S 3S 4s 5S 6S 3 3V 6 6V 9 9V 13 2V 16 5V 19 8V Flow charts for LIFE functions are same as LI PO flow charts above but show LIFE type instead STORE MODE for Lithium Battery Types Store Mode is an important function to insure best performance from your lithium based LiPo and LiFe batteries We suggest using STORE whenever your batteries will be unused for a week or more Connect your battery via both main wires and balance connector as during normal balance charging but select STORE mode as shown in the LiPo flowchart above The 0606i will then charge or discharge as needed such that approximately 60 of battery capacity remains at STORE END Pb MODE lead acid battery CBATT TYPE Setting charge current Adjust and find the desired charge current which ranges from 0 1A to 6 0A with INC amp DEC buttons Press the ENTER butto
14. to scroll through the various modes Once the mode is settled like CYCLE short press ENTER to start values blinking for editing Lithium Care Whenever Lithium battery charging is started with Balancer properly connected the display will show BALANCER CONN CONNECTED If you see instead BALANCER CONN NOT CONNECTED stop and check your connections carefully and repair or replace if needed We strongly recommend balance charging for LiPo and LiFe packs at all times To maximize your investment in Lithium Battery packs do the following e ALWAYS Store your packs at 55 65 of capacity After a day of flying use STORE Mode to achieve this It is especially harmful to store lithium packs fully charged and should be avoided for more than a week at most e AVOID discharging cells beyond 90 of capacity NEVER fully discharge lithium packs e KEEP your packs in a cool dry location whenever in storage Note The EOSO606i does not support charging of legacy 3 6v Lithium lon cell types Never attempt to charge these cells under any circumstances using this charger LITHIUM POLYMER I ON MODE for 3 7V cell types only Number of LiPo Cells Wired in Series Pack Voltage 1S 2S 3S 4s 5S 6S 3 7V 7 4V 11 1V 14 8V 18 5V 22 2V LiPo CHARGE l LiPo DISCHARGE HCL LiPo STORE LiPo BALANCE 6S C 3300mAh 6S D 1 00 A 6S C 3300mAh 6S 0 00 0 0080 00V Setting LiPo Life battery capacity 2100mAh 3S pack example A
15. y using a NiMh battery as an example When the charger is first connected to input power it will display the previously used battery configuration This is especially convenient if you often charge the same type of battery 1 If NiMh is not shown short push the BATT TYPE button to scroll through all battery types Stop when you reach NiMh 2 Short press the ENTER button to select C charge rate in Ampere 3 Press INC or DEC buttons to choose the proper rate for your battery pack Charging NiCd and NiMH is mostly automatic and the setup routines are the same for both You only need to consult the documentation for your battery pack or ask your dealer to determine the proper charge current in Ampere A If the rate is given in mA note that 100mA equals 0 1A so 900mA would be 0 9A for example 4 Attach your NiMH battery to the EOS 0606i Output side harness checking that polarity is correct 5 LONG press the ENTER button hold down for about 1 2 seconds to begin charging NO BATTERY error if battery not connected OPEN CIRCUIT error if the battery becomes disconnected from the charger after START REVERSE POLARITY error if the battery is connected in reverse In our NiMH charging example above we pressed the ENTER button when NiMH was blinking to go directly to charge rate setting However if you want to enter DISCHARGE or CYCLE modes you can press the BATT TYPE button to start NiMH blinking then press INC DEC buttons
Download Pdf Manuals
Related Search