Jb101 V2.2 User manual.pmd
Contents
1. lt user 123456 00000 gt lt user gt is command lt 123456 gt is GPRS user name lt O0000 gt is GPRS password After send SMS tracker will reply lt Set GPRS User and Password oko 8 5 GPRS time sending interval Auto track This command is sent to call the data from the tracker after Interval time Send SMS lt at30sum0 gt to the unit it will reply lt Auto track set ok And after every 30 seconds the data will report to the software platform The min intervals can be sent is for 10 seconds Maping World 9 Troubleshooting After installing itin the first time if device can not get connected with platform server Please check the installation of device 1 Check whether 3 LEDs are functioning accordingly as follow else refers to the user manual contents Red Blinking Green Stable Blue Stable 2 Check whether SIM card is installed correctly and have enough balance for the SMS GPRS 3 Check whether GPS is located if not please drive to the open areas for positioning Hit is offline status in platform Please check the SIM card status 1 Call the SIM card number of the device to check whether you can get through the Sim card or the Sim card is powered off 2 Check whether the vehicle is inno GSM area such as basement 3 Check whether the Device ID entered in the Platform and the Sim Card number should be same To add a Device ID to the Tracker kindly SMS number Sim card mobile number For Ex SMS2. the car moves more than 80 km hr speed The customer will get an SMS Alert Cancel Send SMS nospeed password to deactivate the over speed alert 7 8 Geo fence Set up a geo fence for the unit to restrict its movements within a district The unit will send the message to the authorized numbers when it breaches the restricted area Set up The user can Send SMS lt stockade password space MinLatitude MinLongitude MaxLatitude MaxLongitude gt to unit to set the restricted district Incase of breach it will send SMS lt stockade geo info gt to the authorized numbers For example send SMS lt stockade123456 22 548 123 114 081234 22 549123 114 082234 gt to the unit Remark The first latitude amp longitude is coordinate of min of the Geo fence while the second latitude amp longitude is the coordinate of the max It will alarm one time in each setting Cancel Send SMS lt nostockade password gt to deactivate this function This function will be out of effect after the unit moves outside the district 79 Restart the tracker Send SMS lt reboot password gt to the tracker For example lt reboot123456 gt The tracker will be restarted It will reply lt system will reboot gt This command is given if some majorly new changes have done 7 10 Enquiry Positioning Send SMS lt position password gt to the unit then the unit will send SMS with real time longitude and latitude encrypted in the Google map link and the current speed of
3. the car to the cell phone For example SMS lt postion123456 gt and it will reply the Google Co ordinate 7 11 Set country time zone For different countries there is different time zone The user can set their country time zone by sending the SMS command The format is lt zone password space time zone value gt For example lt zone123456 5 5 gt is set 5 5 time zone Time zone value ranges from 12 to 12 After send SMS tracker will reply lt Set Time Zone OK gt 7 12 SOS alarm In emergency case press SOS for 3 sec to activate SOS alarm Then the device will send SOS SMS to specified Admin as lt Help Me gt Note For using this facility make sure the Specified number is added in the Admin list of the tracker If no Admin number is added the Tracker will not send SOS alarm SMS to any mobile number 7 13 Accident Shock alarm When ever the Driver is driving the car rashly and the car is suffering witha lot of shocks or a accident happens The Tracker will immediately send a SMS alert to the Admin Number as lt Car Rash Driving gt GY Maping World 8 Programming the GPS Tracker to connect with the Web Software The SMS command format should be allin small letters and sent one by one after receiving the confirmation SMS back from the GPS tracker SIM Card Ifthe SMS not come back please check your command else send the command again 8 1 Set GPRS APN Settings in the tracker For example When the device goes to Ind
4. 23456 15889384493 noadmin 123456 15889384493 password 123456 138138 resume Password opendoor123456 closedoor123456 supplyelec123456 stopelec123456 allmonitor123456 restricmonitor 123456 closemonitor123456 move123456 nomove123456 speed123456 080 nospeed 123456 stockade123456 coordinate coordinate nostockade123456 reboot123456 position123456 at10sum0 apn123456 XXXXXX user name pass ip182 18 161 55port5001 number15889384493 zone123456 5 5 1mei123456 Admin OK No Admin OK Ch Passvvord OK Resume Pass Ok Opened OK Closed ok Supply Elec OK Stop Elec OK Set All Mon OK Set Rest Mon OK Set Close Mon OK Move OK No Move Ok Speed OK No Speed OK Set GeoFence Ok NoGeo Fence OK System will rebot Postion Info Set Auto Track Ok Set APN Ok Set GPRS User OK Set Ip Port OK Set Number Ok Set Time zone OK imei number World Manual Version 20120227 c CopyRights by Maping Suryansh tracking Pvt Ltd www mapingworld com
5. Cut Relay 12V Direct Electricity Control Door Control 8 x Electricity Circuit Wire Cups i 12V Direct k White Yellow Air Conditioner Orange SOS Blue Shock Sensor Gray GND Black Company Use GND Black GND Black Power Red Temperature Sensor Green Black Lights Purple Fuel Sensor Yellow Black Ignition Green GND Black Door Status Brown Instructions to connect the wiring Power The standard voltage is 9V 24V DC Please use the power cable which is provided with the GPS tracker only Connect the Red cable No 16 with the direct 12 V of the car The black wire No 8 is the negative The negative should be connected to earth alone of the car or link any iron during installing Do not connect it to any other ground wire which is also being used for any another function of car World ACC Ignition The green wire No 14 should be connected to the ACC switch of the vehicle Please make sure to connect the ACC of the car as many reports in the software are based on ACC Ignition Light On Off Detection The Purple vvire No 15 should be connected vvith the Head Lamp Povver On Off wire to detect the current when the light is On Off When the current flows in the wire it will state as Light is ON Fuel Sensor The Yellow Black wire No 11 of the tracker should be connected with the Digital Output of the Fuel Gauge in the car Every car has a gauge in the f
6. G m Maping Worl Live Satelite Tracking GPS Vehicle Tracker User Manual Version 2 0 Contents 1 Accessories Included inthe BOK KRN nstdcdeuddeaeseedotedsoedeeuets 3 1 uu ba aaa aa asi 4 3 SMC ALO INS AR RA RAR a EAN 2 EI acs as nan weenie 6 5 Preparalionbelore installull ni a aaa 6 Plana al b daaa ao 6 7 Basic Programming of GPS Tracker 8 8 Programming the GPS Tracker to connect with the Web Software 1 a E YARAR asan 12 Qe Maping World 1 Accessories Included in the Box GPS Tracker Power Cable 16 Pins Relay Microphone SOS Button Sim Tray Shock Sensor GPS Antenna GSM Antenna This Component is optional and available with selective models only Please read this manual carefully before attempting installation and onlineactivation Pictures are for indication and illustration purposes only Any miss happening with the Car or car passengers our company will not be liable for any loss caused due to any reason G MapingWorld 2 Features 9 s m rece et Live Tracking of the vehicle via Internet Software and Mobile Control power supply of the car Lock Unlock the Doors Over Speed reporting Geo fencing reporting Movement alert Accident Shock alert SOS Hi jack button for em
7. e car s hould cut and connect both ends of the wire with the relay No 87 and 30 The No 85 should be connected to vehicle positive power 12V The No 86 should be connected to the device yellow wire No 5 Please refer to wiring diagram This function is Available in selected vehicles only depending upon Car Manufacturers SOS Button Connect the SOS button blue wire with the blue wire No 6 and black wire with the tracker black wire No 7 Temperature Sensor The wire No 9 No 10 will be having a temperature sensor pre installed Just place and fix it nicely at the place you need to detect the Temperature 7 0 Basic Programming of GPS Tracker 7 1 Add authorized number as a Admin This command is generally used to bind the tracker witha particular Mobile number After this command the tracker will only revert to that particular Mobile number Also 1 Admin mobile can make another 4 Sub Admin by sending the SMS from Admin mobile only Send SMS lt admin123456 1588938832 gt lt Admin gt as instruction lt 123456 gt as password lt 15889388832 gt as authorized number It will reply lt admin ok gt Maping World 7 2 Delete authorized admin number Send SMS noadmin123456 15889388832 gt lt noadmin gt as instruction lt 123456 gt as password lt 15889388832 gt as deleted number It will reply lt noadmin ok gt 7 3Change the Password Send SMS lt password old password space new password gt to cha
8. ergency Voice monitor of the car Power Cut Alarm when the power supply is disconnected Voided Built in Battery back up Air Condition On off status detection Engine On Off status detection Lights On Off status detection Door Open Close Detection Temperature sensor Fuel sensor Refers to optional functions in selective models Refers to function available in selective vehicles Car models only according to car specification Q Maping World 3 Specifications 7 Weight with Box 04650 g 17LX 11WX7 5H cm Operational Temp 20 to 70 Degree 5 95 Condensing 6 MapingWorld 4 Light Indication GREEN GSM GPRSOK 1 Sec 1 Blink Initilization GSM Error 3 Sec 1 Blink GPRS Pro Be Ges GPS Not Found Initilization GPS Error 5 Preparation before installation 5 1 Open the packing box to check whether the type of device is correct and whether the accessories are included or else please contact your nearest dealer 5 2 Choose SIM card Each device needs to insert a GSM GPRS enabled SIM card only Please refer to the distributors suggestions to choose the SIMcard Do remember GSM sim card you buy should be GPRS Enabled It should not have any kind of pin code security password If there may be any Password of GSM Sim card the Sim card will not perform with the GPS tracker modem on near the Sim tray slot by a needle or a narrow Object place SIM card in the Sim tray accordingly Then insert t
9. he SIM tray again into the slot do not insert the SIM card without tray or in wrong position When the SIM card is placed in rite direction you can see the Red LED glowing 6 Installation Please refer installation to an auto electrical or professional car engineer for any kind of installation The company will not be liable for any Loss Damage to the car due to GPS tracker installation 6 1 Where to fit the tracker To prevent theft of the device itshould be installed in covertly hidden place if possible Avoid placing the device close to higher power electrical devices such as reversing radar anti theft device or other vehicle communication equipment The device should be fixed into position withcable ties or wide double side tape The device has GSM antenna and GPS antenna During installation please make sure that the GPS Antenna is placed at such a place which has no metal object above the device to interfere with GPS reception 6 Maping World The following places are suggested for installation Shelter in the decorated board below the front windshield Shelter around the front instrument panel non metallic material face In the decorated board below back windshields Notice ifthe windshield is pasted with metal thermal protective coating It may affect the receiving signal In this case please change the installation place 6 2 Vehicle Tracker Wiring Diagram ST 101 WIRING DIAGRAM 30 I
10. n to this mode In this mode any number can monitor this unit For Ex If you call the tracker the call will be picked up and you can hear the Microphone voice in the car 2 Restrict Monitor Mode Send SMS lt RestrictMonitor gt to the unit the unit will return to this mode In this mode authorized number can monitor this unit 3 Close Monitor Mode Send SMS lt CloseMonitor gt to the unit the unit will return to this mode In this mode all numbers can not monitor this unit by SMS but if they call the tracker the call will cut and the Position SMS will come back lt 123456 gt as password When ever the car moves more than 80 km hr speed The customer will get an SMS Alert Cancel Send SMS lt nospeed password gt to deactivate the over speed alert GY Maping World 7 6 Movement alert Set up The user can send SMS lt Move password gt to the unit then the unit will reply lt move ok gt In case of there is a movement of car it will send SMS lt Move gt along with a Geo info to the number For example send SMS lt Movel23456 gt to the unit lt Move gt as instructions lt 123456 gt password Cancel Send SMS lt nomove password gt to deactivate the movement alert 7 7 Over speed alert Set up Send SMS lt speed password space 080 gt to the unit Suppose we set the speed is 80km h For example send SMS lt speed123456 080 gt lt Speed gt as instruction lt 80 gt as limit speed and lt 123456 gt as password When ever
11. nge the password For example Send SMS lt password123456 138138 gt lt Password gt as instruction lt 123456 gt as old password lt 138138 gt as new password Password must be six digits Tracker default password is 123456 If you forget your password you can resume the default password 123456 Send lt resumepassword gt to the tracker the tracker will resume the default password If there is no authorized numbers all numbers can resume initial password If there is already authorized numbers only the authorized numbers can resume default password 7 4 Open Close Door Send SMS lt closedoor 23456 gt to lock the doors For example send SMS lt closedoor123456 gt lt closedoor gt as instruction lt 123456 gt as password To open the door again send SMS lt opendoor123456 gt to the unit For example send SMS lt opendoor123456 gt to the tracker lt opendoor gt as instruction lt 123456 gt as the password 7 5 Control Circuit Electricity Send SMS lt stopelec123456 gt to control circuit For example send SMS lt stopelec123456 gt lt stopoil gt as instructions lt 123456 gt as the password To supply the circuit again send SMS lt supplyelec 123456 gt to the unit For example send SMS lt Supplyelec123456 gt to the tracker lt lt Supplyelec gt as instruction lt 123456 gt as password 7 6 Monitor mode There are three modes for monitor 1 All Monitor Modes Send SMS lt AllMonitor gt to the unit the unit will retur
12. number15889388843 If the device GSM function is normal but can not locate fora long time please check whether the installation setup of device is correct 1 Please make sure the GPS antenna is facing up 2 Please make sure there is no electromagnetic wave absorbent object metal above the device especially the thermal protective coating on the windshield it may affect the GPS reception of the device 3 If GPS can not receive the signals normally there is high building around to interfear with GPS reception please drive to the open areas for positioning Generally it needs 60 80 Sec to receive the first coordinates If the Tracker was working fine earlier but suddenly all LED lights are powered off 1 Kindly check the fuse of the tracker which is in the red wire of the power cable 2 Kindly check the wiring In most of the cases while installing the tracker the engineer may leave some wire loose due to which the trackers come into Power off mode after the battery of the tracker is also low 3 Please contact customer care or nearest companys authorized service center Add number as Admin Delete Admin number Change Password Resume Password Door Control Control Circuit Set Monitor Mode Movement Alert OverSpeed Alert Geo Fence Alert Reboot tracker Enquire Position Auto Track Interval Set GPRS APN Set GPRS User Name Pass Set IP and Port Address Set Device ID Set Time Zone IMEI admin1
13. onesia and the customer put the Sim card of Indonesian Telecommunication So the tracker has to be programmed withthe GPRS setting which is of that particular telecommunication company Every Company has different APN Access Point Name For searching your telecommunication APN setting please call to the Helpline of that particular Telecom Company SMS lt apn 123456 cmnet gt Reply Back set APN OK 8 2 Modify IP address and port To send the data to a specific IP of the software you need to SMS the following command to the tracker and the tracker will start sending all data to the specified IP Send SMS lt ip ip address PORT Port Address gt to the unit If the platforms IP address and port is 182 18 188 143 and 5001 send SMS lt ip182 18 188 143por5001 gt to the tracker It will reply lt set IP address and PORT ok gt After this device will send GPS data to this particular IP and Port only 8 3 Set Device ID number In order to identify device on the software platform itis must to set a unique device ID every device Send SMS lt number tracker ID number gt to the tracker For example lt number13612345678 gt We recommend to make the Sim Card number as the device ID 8 4 Set GPRS username and password Optional Some country has GPRS user name and password forGPRS communication To activate the GPRS in the tracker please send the following command lt user space GPRS user name space GPRS password gt For example
14. uel tank This fuel gauge has 3 wires as Positive Negative Digital Output wire Kindly connect No 11 wire with the digital Output wire only Air conditioner On Off Detection The Orange wire No 3 should be connected with the Air Conditioner Power On Off wire to detect the Status when the Air Conditioner is On Off When the current flows in the wire it will state as Air Conditioner is ON Shock Sensor Shock sensor have 3 wires Black wire should be connected with the Black wire No 12 of the tracker Red wire should be connected with the 12 V of the car Gray wire should be connect with Gray wire No 2 of the tracker Also the Shock sensor range should be adjusted manually to the maximum This sensor should be screwed nicely with the body of the car so that you get the accurate results It can be fixed near the Accelerator Pedals of the car hidden and screwed on the metal body of the car Door Status Detection The Brown wire No 13 should be connected with the Door Open Close Istatus main wire which has the voltage when the doors are opened When the doors are closed the Voltage will be O Electricity cut off The Ignition wire of the car should cut and connect both ends of the wire with the relay No 87 and 30 The No 85 should be connected to vehicle positive power 12V The No 86 should be connected to the device white wire No 4 Please refer to wiring diagram Door Lock Door Lock Unlock Circuit wire of th
Download Pdf Manuals
Related Search