3XMag Manual - Edgar Brothers
Contents
1. 1 PRESENTATION The Aimpoint 3XMag Magnifying Module can be used in conjunction with most Aimpoint sights for long range aiming alternatively whenever the situation needs closer or more detailed aiming capability The 3XMag can also be used as a hand held 3X observation device The 3XMag has no reticle itself but uses the red dot in the Aimpoint sight as the aiming reticle thus eliminating the need for re zeroing when shifting from non magnified to magnified aiming and vice versa The 3XMag is rubber covered for increased protection from shock as well as an ergonomic grip when used as a mon ocular For quick attachment and release we recommend the use of the Aimpoint TwistMount 2 SPECIFICATIONS Optical System Magnification Objective diameter Field of view FOV Exit pupil diameter Eye relief at 5 FOV at full FOV Dioptric adjustment Photopic integral transmission Spectral transmission Resolution lp mrad Parallax at 200 meters Physical Specifications Dimensions LxWxH Weight Material housing 3X 20 mm 7 mm 40 90 mm 60 65 mm Fixed 1 0 D gt 80 gt 60 700 1000 nm gt 12 lt 0 2 mrad 110 mm x 44 mm x 41 mm 4 3 x 1 7 x 1 6 200 grams 7 1 ounces including rubber cover Anodized aluminum dark grey rubber covered black Environmental Specifications Temperature range 45 C to 70 C in operation and storage Humidity 0 100 condensing or non condensing Immersi2. DER EXTREME CONDITIONS Use in extreme heat or cold salt air sea spray water mud and snow dust and sand storms or high altitudes doesn t require any special procedures CAUTION The lenses shall never be cleaned with fin gers but with a lens paper cloth If no lens paper cloth is available simply blow away the dirt or fog up the lenses and dry them with a clean and soft piece of cloth 5 MAINTENANCE The 3XMag does not require any particular maintenance while used under normal conditions Aimpoint User s Manual for Aimpoint 3XMag Aimpoint AB Aimpoint Inc J gershillgatan 15 14103 Mariah Court SE 213 75 Malm Sweden Chantilly VA 20151 2113 USA Phone 46 0 40 671 50 20 Phone 1 703 263 9795 Fax 46 0 40 21 92 38 Fax 1 703 263 9463 e mail info aimpoint se e mail info aimpoint com www aimpoint com www aimpoint com THE FUTURE IN SIGHT 2007 Contents property of Aimpoint All rights reserved 11358 2
3. esn t need to be removed 3 2 Installing the 3XMag on the weapon For quick attachment and release of the 3XMag we recommend the use of the Aimpoint TwistMount see pict below The height of the 3XMag mount should be such that the optical center axes of the 3XMag and of the Aimpoint sight coincide see pict below Select a suitable position of the 3XMag on the weapon base so that the eye relief will be correct and comfortable Aimpoint sight a gt Same optical axe as sight Er eo ees m TwistMount Assemble the 3XMag to the mount chosen and install it on the weapon The 3XMag should be mounted with the flat metal surface facing downwards Aimpoint logo on top Carefully tighten the mount to the weapon base and re tighten after a few rounds 3 3 Operation procedures The 3XMag does not need to be zeroed However the Aimpoint sight used together with the 3XMag must be zeroed so that the red dot of the sight creates the correct point of impact Additionally the 3XMag has two Allen screws which allow the user to center the red dot of the Aimpoint sight when viewed through the 3XMag Centering the dot inside the 3XMag is not necessary but creates a more natural feel NOTE Any adjustment of the 3XMag does not affect the point of impact Do not continue to adjust the screws if you encounter resistance The Aimpoint 3XMag Magnifying Module is now ready to be used 4 OPERATION UN
4. on 20 meters 67 ft Mechanical interface The 3XMag is provided with a 30 mm diameter tube for mounting and with 4 screw holes in the bottom surface for other mounting alternatives 3 OPERATION UNDER NORMAL USE WARNING Ensure that the weapon is unloaded the safety selector is in the safe position and the weapon is pointed in a safe direction before attempting to install remove or per form maintenance on the 3XMag other than attaching and detaching it under normal use 3 1 PREPARATION FOR USE The 3XMag can be mounted on the rail of the weapon in three different ways PRIMARY by means of a ring attached to the front 30 mm diameter tube for example the Aimpoint TwistMount see picture under chapter 3 2 OPTION 1 use the rear 30 mm diameter tube in conjunc tion with the front tube OPTION 2 use the four M3 screw holes on the bottom surface for custom mounting hardware In order to use the 30 mm diameter tube s the rubber covering that surface must first be removed Remove rubber from the front tube as shown in fig 2 below when Twist Mount or one ring is used most common Remove rubber from both tubes as shown in fig 3 when both tubes are used Use a sharp knife and carefully cut through the rubber along the circumferential groove making sure not to cut into the metal body Fig 1 Aimpoint 3XMag Fig 2 Fig 3 with rubber If the lower four screw holes are used for mounting the rub ber do
Download Pdf Manuals
Related Search