EST-1000 Handheld Intelligent Toxic Gas Detector User Manual
Contents
1. III Performance Parameters Optional electrochemical Product name Gas detection alarm Sensor name sensor Type of product EST 2000 Type of sensor External power SVDC S500mA Detecting target Toxic gas optional supply pe ofbaten monay Betton panoi stochenie Banery volage 37V huge mision42 Detston metoa Dimsion Fay cpaciy 00 Docetonronge Op Smaown conen zama nony SRS C sampone 210 O Resowon opo Operating Alarm current lt 50mA 10 C 40 C temperature Protection Protection class IP65 dustproof and waterproof Humidity 0 95 RH Way of display LCD liquid crystal display Pressure range 860 1060hpa Wy ofalrm Tooke oft wundandightalam Pechatiine aseos passione WA SSS d CCS ie 2 ean swam a n sich Dimensions of 120 60 35mm Span drift lt 5 FS 6h appearance Weight of lt 250g including batteries Repeatability lt t2 FS machine Note Please refer to the corresponding sensor technical manual for the sensor parameters ENVIRONMENTAL SENSOR TECHNOLOGY CO INC 4 11 IV Notes The use maintenance and calibration of the instrument shall be taken by special people 1 Both of the zero point and full scale shall be calibrated once every three months 2 The detection probe shall be cleaned on a regular basis Otherwise the dust and impurities will plug into the gas hole which will make the sensitivity of the sensor decreased 3 Since the date of th2. Timepiece 4 Paramiter 5 Setting 2 Alarm 3 Calibration 2 Timepiece Setting Select the first option 1 Timepiece in the Main Menu and then press the Confirm to enter the setting of timepiece There are three options in the sub menu of Timepiece 1 Time 2 Date and 3 Y W the first option is to set the hour and the minute the second option to set the month and the date and the third option to set the year and the week Press the Up Down to scroll through the options and press the Back to return to the Main Menu and pressing the Confirm again could enter the parameter altering status Press the Shift to select the parameter to be altered and press the Plus and Minus to make the alteration and then press the Confirm to save it and return to the Main Menu Pressing the Back will not save the alteration but return directly The highlighted option is the current selected option as bellow cuca 00 Timepiece Timepiece 1 Time 12 00 1 Time 12 00 2 Date 2 Date 3 Alarm Setting Select the second option 2 Alarm in the Main Menu and then press the Confirm to enter the setting of alarm There are three options in the sub menu of Alarm 1 Low 2 High and 3 Mode the first option is to set the low value the second option to set the high value and the third option to set the mode of the alarm Press the Up Down to scroll through the options and press the Ba
3. 0 seconds the LCD shows Turn on for about 1 second the alarm light is on the buzzer sounds and it waits for the completion which is shown as the following right picture Warm up Turn on m 30s 2 Detection Status After the successful booting the instrument enters the detection status automatically and the LCD shows all kinds of information at real time which is shown as follows capacity and other signs at real time such as the alarm status buzzer status and link status of the 2 00 x 7 ph The top of the LCD shows the time battery communication The left side of the LCD shows the types of PPM gases The right side of the LCD shows the i measurement unit 3 The large figure in the middle of the LCD is the AVE 10 M AX 20 real time gas concentration 3 i The lowest line of the LCD shows the average and maximum value measured since this booting 3 Time Check and Graphics Status In the detection state press the Confirm shortly press Power Confirm to enter the state of checking the time and date The LCD shows as the following left picture shows Then press the Back and exit and return to the detection state In the detection state press the shift shortly press Menu Shift to enter the state of checking the graphics The LCD shows the gas concentration at real time in the curve The types of the gases and concentration value are shown beneath the curve Then
4. EST 1000 Handheld Intelligent Toxic Gas Detector User Manual Please read this manual carefully before using ENVIRONMENTAL SENSOR TECHNOLOGY CO INC Contents I PROGUCE QV Cr VIC W onio a iat eat ead esees l EET OCE CSC ON ee En E E l I Periorimance Parameters ysscvascesccsessrasecstesaastevossaavaseetcammasasorancenenisevioees 3 IV NO eree AEE ERE OI E EE 4 Ve Operational PLOCES SES sisiane neinna ia e 4 Wie Menu Dese PHO esnin E be meseaaeane 6 MI CS ala DRAM VICE OG earai e o E eet sens 9 VT Troubleshoot INO snr EE ntseenminceeienvcenpedcnees 10 TX Instrument Supporting ccccccecccseccsecceecceeceeeceeeceaeceeeceaeeeaeeeaes I Appendix Type amp Specification of the Sensor ccccecccesesceeeeeeeeaeeeeeaees 1 1 11 I Product Overview EST 1000 series handheld intelligent toxic gas detector is an intelligent hand held alarm that detects the concentration of toxic gas in the target gas with high precision and low power consumption by an advanced electrochemical technology EST 1000 series adopt a natural gas diffusion testing method external handheld pump for option The sensor is the advanced electrochemical toxic gas ones which are of high sensitivity and excellent repeatability It is equipped with a LCD liquid crystal display which can observe the concentration of the target gas online check the time date and week It has two levels of alarm output When it exceeds the pre set alarm point the sound an
5. ck to return to the Main Menu and pressing the Confirm again could enter the parameter altering status Press the Shift to select the value to be altered and press the Plus and Minus to make the alteration and then press the Confirm to save it and return to the Main Menu Pressing the Back will not save the alteration but return directly The highlighted option is the current selected option as bellow ENVIRONMENTAL SENSOR TECHNOLOGY CO INC 8 11 eu te el Alarm ifi Alarm 1 Low 0020 PPM 1 Low 0020 PPM 2 High 2 High 3 Mode 8 Mode 4 Software Calibration Select the third option 3 Calibration in the Main Menu and then press the Confirm to enter software calibration There are three options in the sub menu of Calibration 1 Zero 2 Span and 3 Clear the first option is to set zero calibration the second option to set gain calibration and the third option to clear the parameter of the calibration Press the Up Down to scroll through the options and press the Back to return to the Main Menu and pressing the Confirm again could enter the altering status Press the Shift to select the value to be altered and press the Plus and Minus to make the alteration and then press the Confirm to confirm the calibration or the clearing and return to the Main Menu Pressing the Back will not calibrate or clear the value but return directly The highlighted option is the current selected option as bellow
6. d light alarm signal will be started immediately It has two kinds of calibration methods 1 e the software and hardware The calibration can be finished without opening the cover This instrument has the following features 1 Advanced electrochemical sensor makes the performance stable and reliable 2 External power supply of DCSV a rechargeable 3 7V lithium battery built inside and chargeableness upon connected to the external power supply are all provided 3 Large screen LCD can display various parameters with two methods of viewing 1 e with data and curves 4 The time date and week can be set and displayed All the time information can be checked by a 5 It is of the intelligent design full functions zero setting alarm settings and convenient calibration 6 The shell is compact and lightweight which can be put in the pocket or bag and also can be hung on the body and is easy to carry 7 Two levels of the sound and light alarm are available The four bright LEDs alert the user when alarming II Product Description There are five functions an LCD display and 4 LED lights in the front of the product which 1s shown as follows ENVIRONMENTAL SENSOR TECHNOLOGY CO INC 2 11 Among them the LCD screen is used to display the gas concentration time and various information parameters The two LED lights on the top are alarm lamps which flash alternately when the gas alarms The LED at the left side of the botto
7. e delivery to the user if the instrument fails to operate normally within a year due to the quality problems our company will repair or replace it for the user for free If it is over a year the labor cost will be charged 4 Since there is the acid solution in the electrochemical sensor the users shall not disassemble it by themselves Be careful not to damage the film If the acid solution contacts the skin the users shall wash immediately with water in 10 minutes and then go to a doctor V Operational Processes 1 Instrument Booting Connect to the battery if it is connected long press the Power Confirm for about 3 seconds and the alarm light is on as well as the buzzer sounds which means the instrument boots successfully The LCD shows POWER ON for about 0 5 seconds which is shown as follows The display is for reference only Please be subject to the actual object The same below POWER ON Then the LCD shows the company LOGO CGTsensors for about 0 5 seconds which is shown as follows And then it shows the type of the instrument and the program version for about 0 5 seconds which is shown as follows EST 1000 Ver 00 EGF r ENVIRONMENTAL SENSOR TECHNOLOGY CO INC 5 11 Next enter the sensor and wait for the warm up for about 60 seconds Accompanied by the sound of the buzzer the LCD shows the countdown time which is shown as the following left picture After the completion it shows 0
8. ete software zero calibration 4 Software Gain Calibration The calibration condition is same with that of hardware gain calibration Press the relevant button to adjust the instrument to gain calibration condition please refer to the 4 point of the 6 section for the detailed method After the display is stable in about 3 5 minutes after importing the gas if the value displayed on the LCD is not in conformity with the standard gas adjust the value till it is in conformity with the concentration of the standard gas Press the OK to save the data After the data 1s saved the gas could be stopped And then see whether the value of the instrument could be returned to zero quickly in clean air Repeat the above action once and contrast the result with the last one If the results are pretty much the same within the basic error range the adjustment could be stopped and the standard gas could be turned off and the calibration is ended If not the above calibration should be repeated again till the result is satisfied and then software zero calibration is completed Remark the calibration is of great importance and non professional technicians should not operate at random ENVIRONMENTAL SENSOR TECHNOLOGY CO INC 11 11 VIII Troubleshooting Insufficient battery level Recharge or change the battery Can not Start a l Circuit faults Send it back to the factory to repair Zero point or high low gain i High Low Re calibrate ca
9. g the voltage to 1 1 times of the normal atmospheric pressure and controlling the flow rate within the range of 300ml min to 500ml min and then direct the gas to the sensor through gas pipe and standard gas covering After the display of the instrument is stable in about 3 5 minutes check whether the displayed value is in conformity with the concentration of the standard gas passed If not open the upper covering and adjust the span potentiometer of the outer covering of the instrument to make the displayed value in the panel to be in conformity with the concentration of the standard gas After the adjustment the gas could be stopped Then see whether the value of the instrument could be returned to zero quickly in clean air Repeat the above action and contrast the result with the last one If the results are pretty much the same within the basic error range the adjustment could be stopped and the standard gas could be turned off and the calibration is ended If not the above calibration should be repeated again till the result is satisfied 3 Software Zero Calibration The calibration condition is same with that of hardware zero calibration Press the relevant button to adjust the instrument to zero calibration condition please refer to the 4 point of the 6 section for detailed method After the display is stable if the value displayed on the LCD is not 0 adjust the instrument till it is 0 Press the Confirm to save the data and then compl
10. ions in the sub menu of Setting 1 BLT 2 AOT 3 AOV 4 MAD 5 LRV and 6 Reset the first option is backlight time the second option auto power off time the third option the voltage of auto power off the fourth option the communication address of the module the fifth option the reference voltage of LCD LCD grey scale and the sixth option resetting restoring to the default values Press the Up Down to scroll through the list of the options and press the Back to return to the Main Menu and pressing the Confirm again could enter the parameter altering status Press the Shift to select the value to be altered and press the Plus and Minus to make the alteration and then press the Confirm to confirm the alteration or the clearing and return to the Main Menu Pressing the Back will not save the alteration or the clearing but return directly The highlighted option is the current selected option as bellow Setting i Setting BLT 10 Sec 4 MAD 001 5 LRV 2 AOT Note if the BLT is 0 it indicates the backlight 1s not turned off if the AOT is 0 it indicates non auto power off VII Calibration Method To ensure the measurement accuracy of the instrument calibration should be conducted on a regular basis it is recommended to calibrate once every three months and recorded strictly During calibration calibration cap should be added to the sensor except for
11. libration Readings Change the sensor Disabled sensor TEENE Keep polarizing Not enough polarization time Change the sensor Disabled sensor l l Send it back to the factory to repair Unstable Readings Circuit faults PO Adjust Span potentiometer to reduce the gain Self excitation generated in the circuit Turn off high frequency devices around such as frequency AC interference converter and interphone Probe clogged with dust Clean up the dust on the protective covering Slow Response Disabled sensor Change the sensor Time Circuit faults Send it back to the factory to repair IX Instrument Supporting 1 One set of EST 1000 Hand held Intelligent Toxic Gas Detector 2 One General 5V Power Adaptor 3 One Standard 3 7V Rechargeable Lithium Battery 4 One copy of EST 1000 Instructions for Use 5 One copy of Verification Certificate 6 One package of the product Statement The parameters described in the Instruction may change in subsequent versions Please take the actual object as the standard Appendix Type amp Specification of the Sensor ENVIRONMENTAL SENSOR TECHNOLOGY CO INC
12. m of the LCD is the power light which is green and lights when the battery voltage is not enough While the LED at the right side is the communication light that becomes red and flashes once when communicating one set of the data applicable for EST 2000 series only The five buttons on the panel respectively are Power Confirm Menu Shift Back Plus Up and Minus Up 1 Power Confirm long press for about 3 seconds facilitates the power and the instrument switches the on and off machine Short press facilitates the Confirm 2 Menu Shift after booting long press for about 3 seconds facilitates the menu to enter the menu mode Short press facilitates the shift 3 Back long short press will both facilitate the Back and it will return to the last menu or exit the menu mode 4 Plus Up add a displayed unit to the value or turn upward for an option Long press facilitates the continuous operation 5 Minus Up reduce a displayed unit to turn downward for an option Long press facilitates the continuous operation In addition there is a power connector on the left side of the product and the battery is installed in the back cover of the product The parts and names of the products are shown in the following figure ENVIRONMENTAL SENSOR TECHNOLOGY CO INC 3 11 casing light Rubber leet back caver ype tag deslicking tag slot E Screen treatment light batter cover function key Gax Analyzer front caver
13. press the Back to exit and return to the detection state which is shown as the following right picture ENVIRONMENTAL SENSOR TECHNOLOGY CO INC 6 11 aak ime Time 12 00 3 Week WED 3 Data 2009 12 09 4 Instrument Shutdown There are three ways of shutting down the instrument which are the automatic shutdown when the battery capacity is too low the automatic shutdown when the set time is up and the manual shutdown when pressing the power long press the Power Confirm for about 3 seconds The buzzer sounds when shutting down the LCD shows the POWER OFF for about 0 5 seconds shown as the following left picture and then all are off The instrument is shut successfully and enters the low power consumption standby mode If it automatically shuts down because the power capacity is too low it will show Battery Low first before showing POWER OFF which is shown as the following right picture POWER OFF Battery Low VI Menu Description 1 Main Menu In the detection state press the Menu long press Menu Shift for about 3 seconds to enter the Main Menu LCD shows the Main Menu and six options divided by two screens Use the Up Down to scroll through the options and the two screens will be switched automatically The highlighted option is the current selected option as bellow ENVIRONMENTAL SENSOR TECHNOLOGY CO INC 7 11 eu Main Menu CUA Main Menu 1
14. the 4 digit data with the unit is the value after calibration and the 4 digit data without the unit 1s current concentration value __ ea Calibration I Zero 0000 PPM 2 Span 0005 3 Clear eUl Calibration 1 Zero 0000 PPM 2 Span 0005 3 Clear 5 Parameter Setting Select the fourth option 4 Parameter in the Main Menu and there are only two options in the sub menu of Parameter 1 Type and 2 Rage the first option is to set the type of the gas and the second option to set the sensor the last line indicates the ADC value of the gas and the amount of the battery level and is for reference only Press the Up Down to scroll through the list of the options the last line could not be selected and press the Back to return to the Main Menu and pressing the Confirm again could enter the altering status Press the Shift to select the value to be altered and press the Plus and Minus to make the alteration and then press the Confirm to confirm the alteration or the clearing and return to the Main Menu Pressing the Back will not alter or clear the value but return directly The highlighted option is the current selected option as bellow ENVIRONMENTAL SENSOR TECHNOLOGY CO INC pC Paramiter cud x se Paramiter I Type 02 CO 1 Type 02 CO 2 Rage 6 Instrument Setting Select the fifth option 5 Setting in the Main Menu and there are six opt
15. zero calibration After installing the calibration cap import the standard gas through the end of standard gas cap of the gas pipe and the other end of the gas pipe is connected with a safe place The instrument could be calibrated in 2 methods the soft and hard If hardware calibration required the opening of battery cap of the instrument use a small slotted screwdriver to rotate the knob of calibration potentiometer to avoid shock resulting in the knob loosening which will bring errors to the measurement the knob should be fixed by soft ENVIRONMENTAL SENSOR TECHNOLOGY CO INC 10 11 silicone gel when using it you should only take the soft silicone and please apply silicone gel on it after the calibration If you don t want hardware calibration you could press the relevant button to enter the menu calibration mode in the detection state to realize the calibration of the concentration of the gas with software 1 Hardware Zero Calibration Power on the instrument for 30 minutes in clean air or pure nitrogen the power on time of polarization during the first use of the instrument should be over 2 hours After the display 1s stable open the battery cap and adjust the zero calibration potentiometer in the instrument with the screwdriver to make the value displayed on the LCD to be 0 which means that the calibration is succeeded 2 Hardware Gain Calibration Import the standard gas of known concentration through the flow meter reducin
Download Pdf Manuals
Related Search