STANDALONE WIRELESS MOTION SENSOR ALARM
Contents
1. This warranty becomes void if the product has been tampered with damaged by accident damaged in any other way by improper use or has been purchased second hand All production orders have quality inspections For any customer query or in the unlikely event of a pee failure please contact your local office as set out below DO NOT RETURN THE PRODUCT TO THE RETAILER WARRANTY FOR APPLIANCES USED COMMERCIALLY LIMITED TO 90 DAYS PRODUCT STANDALONE WIRELESS MOTION SENSOR ALARM Model No WGWMSA Purchase Date Product Purchased From Your Name Address Phone Number IMPORTANT Please retain this warranty card along with your purchase receipt Please do not post to the retailer FOR ADDITIONAL REMOTES PLEASE CONTACT YOUR LOCAL DISTRIBUTOR See contact details below for distributor locations Contact details 9 00am 5 00pm Mon Fri RhinoCo Technology Australia Head Office 9 Hannabus Place McGrath s Hill NSW 2756 Australia Phone 61 254774708 Fax 61 24577 4885 UK Sales Office Italy Sales Office South Africa Sales Office Unit 6 Ubique Park March Way 24 Piazza Garibaldi 98034 Francavilla Route 21 Corp Park Unit C3 Prospect Close Battlefield Enterprise Park Shrewsbury Di Sicilia ME Italy 311 Regency Drive Irene Ext 30 South Africa SY1 3JE Phone 39 0942 989241 Phone 27 12 345 6626 Phone 44 0845 644 5421 Email sales rhinoco it Email sales rhinoco co za2. a a Watchguard a Alarms amp Surveillance STANDALONE WIRELESS MOTION SENSOR ALARM INSTRUCTION MANUAL Model No WGWMSA www watchgquardalarms com au RoHS YN517 CE Controls PIR motion sensor Alarm speaker Battery low indicator Battery cover Alarm Unit Front Alarm Unit Back Battery low ON indicator OFF RF Remote keyfob Rotary mounting bracket Battery installation Alarm Unit 1 The battery compartment is accessed from the rear of the alarm unit by removing the battery cover 2 Insert two 2 AA size Alkaline batteries not included following the polarity of diagram 3 When the last battery is inserted the alarm will BEEP indicating that the batteries are installed correctly 4 Close the battery cover Low Battery Warning The Battery Low indicator will turn on when the batteries need to be replaced Remote Key Fob The key fob uses 1 x A27S battery included If the red LED remains ON without pressing the buttons this indicates a low battery simply remove and replace with a new battery Installation 1 Place the alarm in the desired location using swivel wall mount bracket provided 2 _ Fix bracket to the wall using the screws supplied Please note that this alarm can also be used free standing Learning Key Fob s to Main Unit Learning the remote s is done by pressing the Learning Button on the sensor and the on button of the
3. key fob simultaneously until you hear BEEP 2 times which means the remote has been successfully learnt into the sensor Repeat this process to learn additional remotes into the sensor maximum of 3 remotes per sensor To delete a remote Remove all the batteries from the sensor and reinstall them Begin learning the required remotes into the sensor using the steps above For additional remotes please contact your local distributor details overleaf Please note Every time the batteries are removed either from the sensor or key fob the remote s need to be re learnt into the sensor When exiting the protected area Simply press ON button of key fob within the distance of 30 meters Line of Sight to arm the unit A confirmation tone BEEP will indicate that the alarm is armed and you have 30 seconds to vacate the area After that if motion is detected the alarm will sound When entering the protected area Simply press the OFF button of the key fob within the distance of 30meters Line of Sight to disarm the unit Please note that when entering the area there is a short beep to indicate that motion has been detected and a 4 second delay to allow the main unit to be disarmed Detection range The motion detector of the alarm unit has a 7 metre 21ft detection range with angles of 60 vertical and 110 horizontal approximately Care and maintenance To clean the case simply use a soft slightly damp cloth with
4. water and wipe dry immediately CAUTION Never use chemicals to clean the case as they may cause damage to the plastic and cause the alarm not to function Troubleshooting The unit does not sound when the batteries are installed Ensure that the batteries are in proper polarity The alarm does not arm Check key fob red light comes on when the ON or OFF buttons are pressed The red light on the alarm unit is ON This is an indicator of Low Battery which means the batteries need replacing The red light on the key fob does not light up when the buttons are pressed Remove the battery cover of the key fob and replace the battery Battery precautions When using this product follow these precautions at all times e Use only the appropriate size batteries e Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment Incorrect polarity may cause damage to the alarm e Do not mix different types of battery such as Alkaline and Carbon zinc or old batteries with new e If the alarm is not used for long periods of time remove the batteries to prevent damage or injury from possible battery leakage e Do not recharge batteries not intended to be recharged as they can overheat and rupture Always follow the manufacturer s directions WARRANTY CARD This product is guaranteed against faulty materials and workmanship for a period of twelve months from the date of purchase
Download Pdf Manuals
Related Search