Touchmonitor User Guide
Contents
1. shown with optional Magnetic Stripe Reader Touchmonitor User Guide 1515L 15 LCD Desktop Touchmonitor Optional Magnetic Stripe Reader Available bb Ti 1 a E TOUCH _ gt SOLUTIONS TOUCHSYSTEMS connectivity Elo TouchSystems 15 LCD Desktop User Guide Revision G P N 008612E Elo TouchSystems 1 800 ELOTOUCH www elotouch com Copyright O 2011 Tyco Electronics Corporation a TE Connectivity Ltd Company All Rights Reserved No part of this publication may be reproduced transmitted transcribed stored in a retrieval system or translated into any language or computer language in any form or by any means including but not limited to electronic magnetic optical chemical manual or otherwise without prior written permission of Tyco Electronics Disclaimer The information in this document is subject to change without notice Tyco Electronics Corporation and its Afffiliates in the TE Touch Solutions business unit in the TE Connectivity Ltd family of companies collectively TE makes no representations or warranties with respect to the contents herein and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose TE reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of TE to notify any person of such revisions or changes Trademark Acknowledgments AccuTouch Elo logo Elo Touch2. MOUSE COM installed for your mouse if you wish to continue using your mouse along with your touchmonitor in DOS To install Windows 3 x and MS DOS touch driver from Windows 98 95 follow the directions below 1 Insert the CD ROM in your computer s CD ROM drive 2 From DOS type d and press the Enter key to select the CD ROM your CD ROM drive may be mapped to a different drive letter 3 Type cd elodos_w31 to change to the correct directory 4 Type Install and press Enter to start the installation 5 Calculate the touchscreen 2 15 Installing the USB Touch Driver Installing the USB Touch Driver for Windows 7 Windows Vista Windows XP Windows 2000 ME and Windows 98 hb Insert the Elo CD ROM in your computer s CD ROM drive If Windows 2000 or Windows 98 starts the Add New Hardware Wizard do the following 2 Choose Next Select Search for the best driver for your device Recommended and choose Next 3 When a list of search locations is displayed place a checkmark on Specify a location and use Browse to select the EloUSB directory on the Elo CD ROM Choose Next Once the Elo USB touchscreen driver has been detected choose Next again na a You will see several files being copied Insert your Windows 98 cd if prompted Choose Finish If Windows 2000 or Windows 98 does not start the Add New Hardware Wizard do the following NOTE For Windows 2000 you must have administrator access rights to i
3. or backward up to 90 degrees CAUTION In order to protect the LCD be sure to hold the base when adjusting the LCD and do nat touch the screen 3 23 IntelliTouch Plus Touch Technology 3 24 User Guide When connected to Windows 7 computers the touchmonitor can report 2 simultaneous touches The IntelliTouch Plus touchscreen can be re calibrated to your displayed video image if needed through the Calibration function in the Elo driver control panel The IntelliTouch Plus driver will only support multiple monitor if they are all using the IntelliTouch Plus touch technology To use multiple IntelliTouch Plus monitors double click on the EloConfig desktop shortcut to open up the Elo Touchscreen Configuration screen elo EloConfig Select Match Touch to Display to calibrate multiple monitors Copyrights Component versions Build info Restart Elo touch device service Restart Tablet Input Service Match touch input to a display for English OS with 7 multiple monitors Match Touch to Display Align all touchmonitors Align Elo Touchmonitors Device info Edge acceleration Disable touch Restore default calibration Touchmonitor Properties Apply to all monitors Hide cursor during calibration Increase size of Windows title bars Common Settings Elo support info Download driver packages for different platforms Online Support Project
4. Magnetic Stripe Reader MSR Interface Connection optional Note If the MSR is installed on the monitor plug the USB cable from the MSR directly to the PC No drivers are required to be loaded To change the MSR function mode from keyboard emulation to HID load the MSR CHANGE MODE EXE utility from the enclosed TouchTools CD or go online to www elotouch com to download this utility MSR function mode can be changed to HID mode from keyboard emulation mode and back using the MSR CHANGE MODE EXE utility 2 11 Product Overview Main Unit Rear View Kensington Lock The Kensington lock is a security device that prevents theft To find out more about this security device go to http www kensington com 2 12 User Guide Installing the Driver Software Elo TouchSystems provides driver software that allows your touchmonitor to work with your computer Drivers are located on the enclosed CD ROM for the following operating systems e Windows 7 e Windows Vista e Windows XP e Windows 2000 e Windows Me e Windows 98 e Windows 95 e Windows NT 4 0 e Windows 3 1 e MS DOS Additional drivers and driver information for other operating systems are available on the Elo TouchSystems web site at www elotouch com The Elo touchmonitor is plug and play compliant Information on the video capabilities of your touchmonitor is sent to your video display adapter when Windows starts If Windows detects your tou
5. OF THE PRODUCT IN NO EVENT SHALL SELLER BE LIABLE FOR THE COST OF PROCUREMENT OR INSTALLATION OF SUBSTITUTE GOODS BY BUYER OR FOR ANY SPECIAL CONSEQUENTIAL INDIRECT OR INCIDENTAL DAMAGES Buyer assumes the risk and agrees to indemnify Seller against and hold Seller harmless from all liability relating to 1 assessing the suitability for Buyer s intended use of the Products and of any system design or drawing and ii determining the compliance of Buyer s use of the Products with applicable laws regulations codes and standards Buyer retains and accepts full responsibility for all warranty and other claims relating to or arising from Buyer s products which include or incorporate Products or components manufactured or supplied by Seller Buyer is solely responsible for any and all representations and warranties regarding the Products made or authorized by Buyer Buyer will indemnify Seller and hold Seller harmless from any liability claims loss cost or expenses including reasonable attorney s fees attributable to Buyer s products or representations or warranties concerning same Check out Our Website www elotouch com Get the latest e Product information e Specifications e News on upcoming events e Press release e Software drivers e Touchmonitor Newsletter Getting in Touch with us To find out more about TE s extensive range of Elo touch solutions visit our website at www elotouch com or simply ca
6. SD control menu will move to the right side of the screen Likewise when the W button is pressed the OSD control menu will move to the left side Moves the OSD position vertically on the screen When the A button is pressed the OSD control menu will move to the top side of the screen Likewise when the Y button is pressed the OSD control menu will move to the lower side Adjusts the amount of the OSD menu is displayed Press Aor W to select 9300 6500 5500 7500 and USER Only when selecting USER can you make adjustments to the R G B content Press Enter to restore to factory default setting Press Auto to enable this function The Auto Adjust will automatically adjust V Position H Position Clock and Clock Phase Returns the monitor to its default settings Select from English French German Spanish and Japanese Indicates the current resolution H Frequency and V Frequency 3 21 3 22 User Guide Preset Modes To reduce the need for adjustment for different modes the monitor has default setting modes that are most commonly used as given in the table below If any of these display modes are detected the monitor automatically adjusts the picture size and centering When none of the mode is matched the user can store their preferred modes in the user modes The monitor is capable of storing up to 7 user modes The only condition to store as a user mode is the new display information must have 1 KHz difference for horizontal fre
7. Systems IntelliTouch TE Connectivity TE connectivity logo and TE logo are trademarks of the TE Connectivity Ltd family of companies Windows is a trademark of the Microsoft group of companies Other product names mentioned herein may be trademarks or registered trademarks of their respective companies Tyco Electronics claims no interest in trademarks other than its own Table of Contents Chapter 1 Introduction 7 Product iDescripllOlis assalire 7 Preca tioN Sorosina a as 7 About the proQUCt iii 8 Chapter 2 Installation and Setup 9 Unpacking Your Touchmonitor n 9 Touch Interface Connection i 11 MSR Interface connection Optional 11 Product Overview ii 12 Main UMi t isss innisis enasna 12 Rear VIEW icon e coi 12 KensigntOn LOCK 13 Installing the Touch Driver Software 14 Installing the Serial Touch Driver not applicable to Acoustic Pulse Recognition and Projected Capacitive MONTON iii 14 Installing the Serial Touch Driver for Windows 7 Windows Vista Windows XP Windows 2000 ME Windows 98 95 and NT 4 0 0 0 eee 14 Installing the Serial Touch Driver for Windows 3 1 and MS DOS 15 Installing the USB Touch Driver 16 Installing the USB Touch Driver for Windows 7 Windows Vista Windows XP Windows 2000 ME and WindoWs Misco ia 16 Installing APR USB Touch Driver for Win
8. an or the manufacturer if there are questions about the installation prior to connecting the equipment to mains power II Emissions and Immunity Information A Notice to Users in the United States This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications B Notice to Users in Canada This equipment complies with the Class B limits for radio noise emissions from digital apparatus as established by the Radio Interference Regulations of Industrie Canada C Notice to Users in the European Union Use only the provided power cords and interconnecting cabling provided with the equipment Substitution of provided cords and cabling may compromise electrical safety or CE Mark Certification for emissions or immunity as required by the following standards This Information Technology Equipment ITE is required to have a CE Mark on the manufacturer s label which means that the equipment has been tested to the following Directives and Standards This equipment has been tested to the requirements for the CE Mark as required by EMC Directive 2004 108 EC indicated
9. anel in Windows to choose 1024 x 768 resolution Operating in other resolutions will degrade video performance For further information please refer to Appendix A All adjustments made to the controls are automatically memorized This feature saves you from having to reset the choices every time the touchmonitor is unplugged or powered off and on If there is a power failure the touchmonitor settings will not default to the factory specifications Side Panel Controls Control 1 Menu Exit 2A 4 Select 5 Power Switch e 0000 Function Display Exits the OSD menus 1 Enter contrast of the OSD 2 Increase value of the adjustment item 3 Move OSD selection clockwise 1 Enter brightness adjustment 2 Decrease value of the adjustment item 3 Move OSD selection counter clockwise 1 Auto adjust function 2 Selects the adjustment item from the OSD menus Switches the power of the monitor 3 19 Controls and Adjustment NOTE 3 20 User Guide OSD Menu Functions To Display and Select the OSD Functions 1 Press the Menu key to activate the OSD menu 2 Use A or W to move clockwise or counterclockwise through the menu Press the Select key the parameter will be highlighted when selected 3 To quit the OSD screen at any time during the operation press the Menu key If no keys are pressed for a short time period the OSD automatically disappears The OSD screen will disappe
10. ar if no input activities are detected for at a minimum of 45 seconds or depending on how long the timer is set via the OSD menu The time ranges from 45 seconds to 255 seconds OSD Lock Unlock The OSD feature can be locked and unlocked The monitor is shipped in the unlocked position To lock the OSD 1 Press the Menu button and A button simultaneously until a window appears displaying OSD Unlock Continue to hold the buttons down and the window toggles to OSD Lock 2 To unlock the OSD repeat the procedure until the OSD Unlock is displayed To lock the power 1 Press the menu and y button simultaneously until a window displaying power unlock appears Continue to hold the buttons until the Power Lock 2 To unlock the power repeat the procedure until the Power Unlock is displayed OSD Control Options Control Brightness Contrast H Position V Position Phase Clock Sharpness OSD H Position OSD V Position OSD Time Color Balance Auto Adjust Recall Defaults OSD Language Information Description Description Increases or decreases brightness Increases or decreases contrast Moves the screen left or right Moves the screen up or down Increases or decreases the snow noise of the image after auto adjustment is made The dot clock is fine adjusted after auto adjust Adjusts sharpness of video Moves the OSD position horizontally on the screen When the A button is pressed the O
11. chmonitor follow the instructions on the screen to install a generic plug and play monitor Refer to the following appropriate section for driver installation instructions Depending upon whether you connected the serial communication cable or the USB communication cable only the serial driver or the USB driver should be installed 2 13 Installing the Serial Touch Driver not applicable to Acoustic Pulse Recognition and Projected Capacitive monitor Installing the Serial Touch Driver for Windows 7 Windows Vista Windows XP Windows 2000 98 95 ME and NT4 0 NOTE For Windows 2000 and NT4 0 you must have administrator access rights to install the driver Make sure the serial connector RS232 is plugged into the monitor and an open com port on the PC 2 14 User Guide N Re uy o DO Ur A Insert the Elo CD ROM in your computer s CD ROM drive If the AutoStart feature for your CD ROM drive is active the system automatically detects the CD and starts the setup program Follow the directions on the screen to complete the driver setup for your version of Windows If the AutoStart feature is not active Click Start gt Run Click the Browse button to locate the EloCd exe program on the CD ROM Click Open then OK to run EloCd exe Follow the directions on the screen to complete the driver setup for your version of Windows Installing the Serial Touch Driver for Windows 3 1 and MS DOS You must have a DOS mouse driver
12. digital device into a different AC outlet so the digital device and the receiver are on different branch circuits v Disconnect and remove any I O cables that the digital device does not use Unterminated I O cables are a potential source of high RF emission levels vi Plug the digital device into only a grounded outlet receptacle Do not use AC adapter plugs Removing or cutting the line cord ground may increase RF emission levels and may also present a lethal shock hazard to the user If you need additional help consult your dealer manufacturer or an experienced radio or television technician 35 III Agency Certifications The following certifications have been issued for this monitor Australia C Tick Canada cUL Canada IC China CCC Asia models only China RoHS Asia models only Europe CE Japan VCCI e United States FCC United States UL Argentina S mark Taiwan BSMI Asia models only Korea MIC Asia models only This class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations Cet appareil num rique de la classe B respecte toutes les exigences du R glement sur le mat riel brouilleur du Canada This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference reveived including interference that
13. dows 7 Windows VISTA and WiINdOwWS O 17 Chapter 3 Operation 18 About Touchmonitor Adjustments eee 18 Side Panel CONtrols inn 19 Controls and Adjustment 0 0 eee ee ee eee eects 20 OSD Menu Functions in 20 OSD LockUnlOck ion 20 OSD Control Options 21 Preset MOdGS ivi iii iii 22 Power Management System 23 Display Adler int 23 IntelliTouch Plus Touch Technology 24 Projected Capacitive Touch Technology 25 Gesture Supporti 25 Chapter 4 Troubleshooting 26 Solutions to Common ProblemSs 26 Appendix A Native Resolution 27 Appendix B Touchmonitor Safetyi ii cri 29 Care and Handling of Your Touchmonitor 30 Waning corria dirt 30 Appendix C Technical Specifications 31 Touchmonitor SpecificationSs 32 15 LCD Touchmonitor 1515L Dimensions 33 Regulatory Information 34 Warranty 37 INTRODUCTION Product Description Your new touchmonitor combines the reliable performance of touch technology with the latest advances in LCD display design This combination of features creates a natural flow of information between a user and your touchmonitor This LCD monitor incorporates a 15 color active matrix thin film transistor TFT to provide superior display performance A maximu
14. e Unpacking Your Touchmonitor Check that the following items are present and in good condition LCD monitor VGA cable USB cable Ela Our Serial Cable CD and Quick Install Guide 2 9 Power cable for European models Japanese PSE power cable Adapter Terminal Power cable for Asia models China CCC power cable Taiwan BSMI power cable Korea KC power cable Power cable for Worldwide models USA UL Power cable Europe VDE power cable 2 10 User Guide Touch Interface Connection Note Before connecting the cables to your touchmonitor and PC be sure that the computer and touchmonitor are turned off Power Cord USB Cable Serial Cable Video Cable For APR Projected Capacitive DC Jack y and IntelliTouch Plus model only Power Cord USB Cable Video Cable 1 Connect one end of the power cord to the monitor and the other end to the AC outlet 2 Connect one end of either the touchscreen serial RS232 cable or the touch screen USB cable but not both to the rear side of the computer and the other end to the LCD monitor Tighten by turning the two thumb screws clockwise to ensure proper grounding optional module USB cable does not have thumb screws 3 Connect one end of the video cable to the rear side of computer and the other to the LCD monitor Tighten by turning the two thumb screws clockwise to ensure proper grounding 4 Press the power button on the front panel to turn the monitor power on
15. ed Capacitive Touch Technology When connected to Windows 7 computers the touchmonitor can report 2 simultaneous touches When connected to Windows XP computers the touchmonitor reports single touches No additional drivers are required for this technology to work it uses Windows HID drivers No calibration is required for this technology Gesture Support The IntelliTouch Plus and Projected Capacitive touch technologies enable several gestures that support single and multiple contacts Refer to the Microsoft Website http msdn microsoft com en us library dd940543 on the various gestures that are supported in Windows 7 3 25 TROUBLESHOOTING If you are experiencing trouble with your touchmonitor refer to the following table If the problem persists please contact your local dealer or the Elo service center Solutions to Common Problems Problem The monitor does not respond when turning on the system Characters on the screen are dim The video is blank Screen flashes when initialized Qut of Range display Touch doesn t work 4 26 User Guide Suggestion s 1 Check that the monitor s Power Switch is on 2 Turn off the power and check the monitor s DC power cord and signal cable for proper connection Refer to the About Touchmonitor Adjustments section to adjust the brightness 1 During operation the monitor screen may automatically turn off as a result of the Power Saving feature Pre
16. in European Standard EN 55022 Class B and the Low Voltage Directive 2006 95 EC as indicated in European Standard EN 60950 D General Information to all Users This equipment generates uses and can radiate radio frequency energy If not installed and used according to this manual the equipment may cause interference with radio and television communications There is however no guarantee that interference will not occur in any particular installation due to site specific factors 1 In order to meet emission and immunity requirements the user must observe the following a Use only the provided I O cables to connect this digital device with any computer b To ensure compliance use only the provided manufacturer s approved line cord c The user is cautioned that changes or modifications to the equipment not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment 2 If this equipment appears to cause interference with radio or television reception or any other device a Verify as an emission source by turning the equipment off and on b If you determine that this equipment is causing the interference try to correct the interference by using one or more of the following measures i Move the digital device away from the affected receiver ii Reposition turn the digital device with respect to the affected receiver iii Reorient the affected receiver s antenna iv Plug the
17. l 70 or 140 total R G B Analog 0 7Vp p 75 ohm TTL Positive or Negative Mini D Sub 15 pin Menu A W Select Power Contrast Brightness H Position V Position Color Temperature Phase Clock OSD Time Recall Language English French German Spanish Japanese DDC 2B AccuTouch IntelliTouch Acustic Pulse Recognition Projected Capacitive IntelliTouch Plus Input AC 100 240V 50 60Hz 0 C 40 C 32 F 104 F 20 80 No Condensation To 12 000 Feet 20 C 60 C 4 F 140 F 10 90 No Condensation 372 8 x 310 x 175mm 5Kg UL C UL FCC B CE VCCI C Tick MPRII S Semko Note Use a UL and IEC certified external AC adapter with a limited power source marked LPS rated 12 Vdc 2 5A C 32 User Guide 15 LCD Touchmonitor 1515L Dimensions REGULATORY INFORMATION I Electrical Safety Information 34 User Guide A Compliance is required with respect to the voltage frequency and current requirements indicated on the manufacturer s label Connection to a different power source than those specified herein will likely result in improper operation damage to the equipment or pose a fire hazard if the limitations are not followed B There are no operator serviceable parts inside this equipment There are hazardous voltages generated by this equipment which constitute a safety hazard Service should be provided only by a qualified service technician C Contact a qualified electrici
18. lamps in the monitor display contain mercury Waste Electrical and Electronic Equipment WEEE Directive In the European Union this label indicates that this product should not be disposed of with household waste It should be deposited at an appropriate facility to enable recovery and recycling TECHNICAL SPECIFICATIONS Touchmonitor Specifications Model LCD Display Display Size Pixel Pitch Display Mode Max Resolution Contrast Ratio Brightness Response Time Display Color Viewing Angle Input Signal Video Sync Signal Connector Side Controls OSD Plug Play Touch Panel optional Power Adapter Operating Conditions Temperature Humidity Altitude Storage Conditions Temperature Humidity Dimensions HxWxD Weight Net Certifications 1515L 15 TFT Active Matrix Panel 304 H x 228 V mm 0 297 H x 0 297 V mm VGA 640 x 350 70Hz VGA 720 x 400 70Hz VGA 640 x 480 60 72 75Hz SVGA 800 x 600 56 60 72 75Hz XGA 1024 x 768 60 70 75Hz XGA 1024 x 768 at 75Hz maximum 500 1 typical Non Touch typical 250 Cd m Min 200 Cd m AccuTouch typical 200 Cd m2 Min 150 Cd m IntelliTouch typical 225 Cd m Min 170 Cd m Acoustic Pulse Recognition typical 225 Cd m Min 170 Cd m Projected Capacitive typical 225 Cd m Min 176 Cd m IntelliTouch Plus typical 225 Cd m Min 170 Cd m Tr 5 7 ms Tf 6ms Typ 16 2M Vertical 60 65 or 125 total Horizonta
19. ll the of fice nearest you North America Germany Belgium Asian Pacific TE Touch Solutions Tyco Electronics Raychem GmbH Tyco Electronics Raychem GmbH Sun Homada Bldg 2F 301 Constitution Drive TE Touch Solutions TE Touch Solutions 1 19 20 Shin Yokohama Menlo Park CA 94025 Finsinger Feld 1 Diestsesteenweg 692 Kanagawa 222 0033 USA D 85521 Ottobrunn B 3010 Kessel Lo Japan Germany Belgium 800 ELO TOUCH 800 557 1458 Tel 49 0 89 60822 0 Tel 32 0 16 35 2100 Tel 81 45 478 2161 Tel 650 361 4800 Fax 49 0 89 60822 180 Fax 32 0 16 35 2101 Fax 81 45 478 2180 Fax 650 361 4722 elosales elotouch com elosales elotouch com www tps co jp customerservice elotouch com 2011 Tyco Electronics Corporation a TE Connectivity Ltd Company All Rights Reserved
20. m resolution of XGA 1024 x 768 is ideal for displaying graphics and images Other outstanding features that enhance this LCD monitor s performance are Plug amp Play compatibility and On Screen Display OSD controls Precautions Follow all warnings precautions and maintenance as recommended in this user s manual to maximize the life of your unit See Appendix B for more information on touchmonitor safety 1 7 About the Product 1 8 User Guide The 1515L LCD Desktop Touchmonitor is a 15 XGA TFT color display with the following features The internal microprocessor digitally controls auto scanning For horizontal scan frequencies between 31 5 KHz and 60 2 KHz and vertical scan frequencies between 56 3Hz and 75 0 Hz In each frequency mode the microprocessor based circuitry allows the monitor to function at the precision of a fixed frequency High contrast color TFT LCD display support resolution up to XGA 1024 x 768 Compatible with VGA SVGA XGA non interlaced and most Macintosh compatible color video cards Power management system conforms to VESA DPMS standard Supports DDC 2B for Plug amp Play compatibility Advanced OSD control for picture quality adjustment Detachable stand for wall mounting application Optional touch screen function For full Product Specifications refer to Appendix C INSTALLATION AND SETUP This chapter discusses how to install the 1515L LCD touchmonitor and the driver softwar
21. may cause undesired operation 36 User Guide WARRANTY Except as otherwise stated herein or in an order acknowledgment delivered to Buyer Seller warrants to Buyer that the Product shall be free of defects in materials and workmanship The warranty for the touchmonitors and components of the product is 3 three years Seller makes no warranty regarding the model life of components Seller s suppliers may at any time and from time to time make changes in the components delivered as Products or components Buyer shall notify Seller in writing promptly and in no case later than thirty 30 days after discovery of the failure of any Product to conform to the warranty set forth above shall describe in commercially reasonable detail in such notice the symptoms associated with such failure and shall provide to Seller the opportunity to inspect such Products as installed if possible The notice must be received by Seller during the Warranty Period for such product unless otherwise directed in writing by the Seller Within thirty 30 days after submitting such notice Buyer shall package the allegedly defective Product in its original shipping carton s or a functional equivalent and shall ship to Seller at Buyer s expense and risk Within a reasonable time after receipt of the allegedly defective Product and verification by Seller that the Product fails to meet the warranty set forth above Seller shall correct such failure by at Seller s option
22. nstall the driver 2 16 User Guide 1 Insert the Elo CD ROM in your computer s CD ROM drive If the AutoStart feature for your CD ROM drive is active the system automatically detects the CD and starts the setup program 2 Follow the directions on the screen to complete the driver setup for your version of Windows If the AutoStart feature is not active 1 Click Start gt Run 2 Click the Browse button to locate the EloCd exe program on the CD ROM 3 Click Open then OK to run EloCd exe 4 Follow the directions on the screen to complete the driver setup for your version of Windows Installing APR USB Touch Driver for Windows 7 Windows VISTA and Windows XP Insert the Elo CD ROM in your computer s CD ROM driver Follow the directions on the screen to complete the APR 3 1 driver setup for your version of Windows Do not plug USB cable until software is fully loaded When finished plug USB cable and alignment data is transferred NOTE For the latest driver go to elotouch com and download it from the driver download section 2 17 OPERATION About Touchmonitor Adjustments 3 18 User Guide Your touchmonitor will not likely require adjustment However variations in video output and application may require adjustments to the touchmonitor to optimize the quality of the display For best performance your touchmonitor should be operating in native resolution that is 1024 x 768 at 80k 75 Hz Use the Display control p
23. quency or 1 Hz for vertical frequency or the sync signal polarities are different from the default modes H Freq Band Width Mode Resolution KHz MHz H vV 1 VGA 640 x 350 70 Hz 31 47 25 175 2 VGA 720 x 400 70 Hz 31 47 28 322 3 VGA 640 x 480 60 Hz 31 47 25 175 4 MAC 640 x 480 66 Hz 35 00 30 34 5 VESA 640 x 480 72 Hz 37 86 31 5 6 VESA 640 x 480 75 Hz 37 50 31 5 7 VESA 800 x 600 56 Hz 35 16 36 8 VESA 800 x 600 60 Hz 37 88 40 9 VESA 800 x 600 75 Hz 46 88 49 5 10 VESA 800 x 600 72 Hz 48 08 50 11 MAC 832 x 624 75 Hz 49 72 57 283 12 VESA 1024 x 768 60 Hz 48 36 65 13 SUN 1024 x 768 65 Hz 52 45 70 49 14 VESA 1024 x 768 70 Hz 56 48 75 15 VESA 1024 x 768 75 Hz 60 02 78 75 Power Management System The monitor is equipped with the power management function which automatically reduces the power consumption when not in use Power Mode Consumption On lt 30W Sleep lt 3W Off lt 1W It is recommend to switch the monitor off when it is not in use for a long time NOTE The monitor automatically goes through the Power Management System PMS steps when it is idle To release the monitor from PMS condition press any key on the keyboard Move the mouse or touch the touchscreen In order for the touchscreen to bring the monitor from the power management system the touchscreen function must be fully operational Display Angle For viewing clarity the LCD can tilt forward up to 5 degrees
24. s either i modifying or repairing the Product or ii replacing the Product Such modification repair or replacement and the return shipment of the Product with minimum insurance to Buyer shall be at Seller s expense Buyer shall bear the risk of loss or damage in transit and may insure the Product Buyer shall reimburse Seller for transportation cost incurred for Product returned but not found by Seller to be defective Modification or repair of Products may at Seller s option take place either at Seller s facilities or at Buyer s premises If Seller is unable to modify repair or replace a Product to conform to the warranty set forth above then Seller shall at Seller s option either refund to Buyer or credit to Buyer s account the purchase price of the Product less depreciation calculated on a straight line basis over Seller s stated Warranty Period 37 38 User Guide THESE REMEDIES SHALL BE THE BUYER S EXCLUSIVE REMEDIES FOR BREACH OF WARRANTY EXCEPT FOR THE EXPRESS WARRANTY SET FORTH ABOVE SELLER GRANTS NO OTHER WARRANTIES EXPRESS OR IMPLIED BY STATUTE OR OTHERWISE REGARDING THE PRODUCTS THEIR FITNESS FOR ANY PURPOSE THEIR QUALITY THEIR MERCHANTABILITY THEIR NONINFRINGEMENT OR OTHERWISE NO EMPLOYEE OF SELLER OR ANY OTHER PARTY IS AUTHORIZED TO MAKE ANY WARRANTY FOR THE GOODS OTHER THAN THE WARRANTY SET FORTH HEREIN SELLER S LIABILITY UNDER THE WARRANTY SHALL BE LIMITED TO A REFUND OF THE PURCHASE PRICE
25. ss any key to see if the screen reappears 2 Refer to the About Touchmonitor Adjustments section to adjust the brightness Turn the monitor off then turn it on again Reconfigure the resolution of your computer to make one of the monitor s supported video mode see Appendix C See Appendix A for more information on resolution Make sure the touch cable is securely attached at both ends NATIVE RESOLUTION The native resolution of a monitor is the resolution level at which the LCD panel is designed to perform best For the LCD touchmonitor the native resolution is 1024 x 768 for the 15 inch size In almost all cases screen images look best when viewed at their native resolution The resolution setting of a monitor can be lowered but not increased Input Video 15 LCD 640 x 480 VGA Transforms input format to 1024 x 768 800 x 600 SVGA Transforms input format to 1024 x 768 1024 x 768 XGA Displays in Native Resolution The native resolution of an LCD is the actual number of pixels horizontally in the LCD by the number of pixels vertically in the LCD LCD resolution is usually represented by the following symbols ELA SVGA 800 x 600 SXGA 1280 x 1024 GA 1024x768 1600x 1200 A 27 A 28 User Guide As an example a SVGA resolution LCD panel has 800 pixels horizontally by 600 pixels vertically Input video is also represented by the same terms XGA input video has a format of 1024 pixels horizontally by 768 pixels
26. to your touchmonitor If your touchmonitor becomes wet do not attempt to repair it yourself Ensure that your installation setup is designed equipped to maintain operating temperature within the specified operating conditions refer to the section TouchMonitor Specifications B 29 Care and Handling of Your Touchmonitor B 30 User Guide The following tips will help keep your touchmonitor functioning at the optimal level To avoid risk of electric shock do not disassemble the brick power supply or display unit cabinet The unit is not user serviceable Remember to unplug the display unit from the power outlet before cleaning Do not use alcohol methyl ethyl or isopropyl or any strong dissolvent Do not use thinner or benzene abrasive cleaners or compressed air To clean the display unit cabinet use a cloth lightly dampened with a mild detergent Avoid getting liquids inside your touchmonitor If liquid does get inside have a qualified service technician check it before you power it on again Do not wipe the screen with a cloth or sponge that could scratch the surface To clean the touchscreen use window or glass cleaner Put the cleaner on a clean cloth and wipe the touchscreen Never apply the cleaner directly to the touchscreen Warning This product consists of devices that may contain mercury which must be recycled or disposed of in accordance with local state or federal laws Within this system the backlight
27. vertically When the input pixels contained in the video input format match the native resolution of the panel there is a one to one correspondence of mapping of input video pixels to LCD pixels As an example the pixel in column 45 and row 26 of the input video is in column 45 and row 26 of the LCD For the case when the input video is at a lower resolution than the native resolution of the LCD the direct correspondence between the video pixels and the LCD pixels is lost The LCD controller can compute the correspondence between video pixels and LCD pixels using algorithms contained on its controller The accuracy of the algorithms determines the fidelity of conversion of video pixels to LCD pixels Poor fidelity conversion can result in artifacts in the LCD displayed image such as varying width characters TOUCHMONITOR SAFETY This manual contains information that is important for the proper setup and maintenance of your touchmonitor Before setting up and powering on your new touchmonitor read through this manual especially Chapter 2 Installation and Chapter 3 Operation 1 To reduce the risk of electric shock follow all safety notices and never open the touchmonitor case 2 Turn off the product before cleaning 3 The slots located on the sides and top of the touchmonitor case are for ventilation Do not block or insert anything inside the ventilation slots 4 Itis important that your touchmonitor remains dry Do not pour liquid into or on
Download Pdf Manuals
Related Search