6130 UM A4-05-05.QXD - strong>strong>strong>strong>
Contents
1. PART 1 e English 18 PAGE Plus Minus Scrolling page by page Page for the next 10 items Page for the previous 10 items 19 Color Buttons Within the Videotext mode the color buttons follow the color codes of the broadcaster In the menu follow the color codes for various functions 20 0 9 Numeric Direct entry of numerical functions in the menus or in channels selection STRONG DIGITAL TV www strongsat com 19 STRONG PART 1 e English DIGITAL TV A 1 Trouble Shooting Occasionally receivers can hang up just like with a PC so you are recommended to reset the receiver by disconnecting it from mains power Wait 30 seconds and connect to mains power again and now check if the unit is working as expected If the receiver does not work properly after checking the trouble shooting section please contact the dealer Don t open the receiver cover it may cause an electrical shock due to high current voltage and the warranty of your receiver will be void if the receiver has been opened Symptoms The green red lights on front panel do not light up No picture and sound No picture and sound No picture and sound No sound No sound or picture No picture The receiver displays the message No or Bad signal during bad weather condi tions heavy rain or snow The receiver displays the message No or Bad signal The receiver displays the message No or Bad signal The receiver2. STRONG PART 1 e English DIGITAL TV 2 Press the BACK button until you go back to the Main Menu m Power on Channel This function allows you to set the channel you want when the receiver turns on To set the power on channel apply the following steps lt Please see inside cover Screen 16 gt 1 Select Power on Channel and press OK or the Right button m Last Viewed The receiver will start up with the channel that you viewed before turning the receiver off m Define Channel This function allows you to set the channel you want when the receiver turns on To define the channel apply the following steps 1 Press OK or the Right button and select in the TV or radio list of channels the channel you want to have your receiver start up with m System Upgrade You can download the latest software available including new technologies to your receiver To upgrade your system apply the following steps 1 Select System Upgrade and press OK 2 A system upgrade is available on ASTRA and on HOTBIRD Choose the satellite your dish points to and press OK The receiver will display the message Please wait checking for new software If there is a recent software version available for your receiver it will automatically download it via the satellite signal If you already have the latest version nothing will happen lt Please see inside cover Screen 17 gt 3 Press the BACK button until you go back to main menu Note Be sure that your receiv
3. 2 Using UP DOWN keys select Channel Organizer and press OK 3 Enter PIN CODE 0000 default code and press OK 4 Press the Red Sort button to sort your channels lt Please see inside cover Screen 2 gt m If you press the Red Name button you can sort the list of channels alphabetically lt Please see inside cover Screen 3 gt m f you press the Green Type button you can sort the channels by the type of the channel Cl or scram bled program m f you press the Yellow TP button you can sort the channels by transponder order m f you press the Blue Manual button you can sort the channels manually A check mark will be shown on the selected channel Use the UP DOWN buttons to move to the position that you want the channel to be at and press the Blue manual button once again The channel will then be moved to the position you selected Once you have finished sorting the channels press the Back button until you are back in the Normal TV mode A message that the receiver is saving the changes you made will be displayed Setting Favourite channels from the channel list You can set a list of Favourite channels from the current TV Radio channels list To set your Favourite channels please apply the following steps 1 Press the Menu button 2 Using UP DOWN keys select Channel Organizer and press OK 3 Press the Green Fav button to switch into Favourite organizer mode lt Please see inside cover Screen 2 gt 4 The default
4. a good condition m Make sure that the SCART cable connections are well shielded m Make sure that the outdoor components of the dish are in good condition m Make sure that the dish is aimed at the satellite of your choice m Make sure that the dish is connected with the correct I F coaxial cable 75 Ohm and is in good condition www strongsat com PART 1 e English STRONG DIGITAL TV 2 0 Your Receiver 2 1 Front Panel Please see inside cover Figure 1 1 Power Button Turns the receiver ON OFF 2 Stand BY ON SIGNAL 3 LEDs The red LED is the stand by indicator The green LED is the Power On indicator The orange LED lights up once you correctly receive a satellite signal signal locked 3 UP DOWN Buttons Move the cursor UP DOWN in Menu state Changes the channels UP DOWN in no menu state 2 2 Rear Panel Please see inside cover Figure 2 1 SAT IN LNB IN Connect the 1 F digital signal from your LNB of your satellite dish to this connector 2 SAT OUT Gives you the possibility to connect an extra receiver analogue or digital 3 AUDIO Right Red RCA and Left White RCA These connectors give you the possibility to connect the audio signal to an external amplifier or to the audio input of your TV 4 VIDEO Yellow RCA This connector has a constant video signal for additional VCR connections 5 TV Scart Connector Use this connector to connect your receiver to your TV using a scart cable 6 VIDEO Scart Co
5. change any of these two settings you must set LNB type to zero If DiSEqC switch is Off you will not be able to change settings in both the DiSEqC Input and DiSEqC Repeat menu items Alternatively if you set LNB Dish to Moved the DiSEqC switch menu item is automatically switched to off if your LNB dish is set to fixed you will be able to select the required DiSEqC level in the DiSEqC switch menu item 6 Press the Red Save button or press the Green Save amp Exit button to save the setting and to return to the installation menu 7 Press the Yellow Back button or Back button if you don t want to save the setting 5 1 4 3 Channel Set up Please see inside cover Screen 20 The channel set up is for downloading the channels available on the satellites There are up to 64 satellites available To download channels please apply the following steps In this menu you can edit the satellites name and edit the transponder of the satellite You can also display the LNB menu and the Positioner Set up menu by selecting LNB and Dish Position respectively 1 Press the Menu button 2 Using UP DOWN keys on your remote select Installation and press OK 3 Using UP DOWN keys select Channel Set up and press OK 4 Use the UP DOWN keys on your remote to select an item and use the Left Right button to set up any values m Satellite Select Satellite and press OK or the Right button The satellite list is displayed and then
6. favourite list names are Movie News Sports and Music 5 Using UP DOWN or P P keys select the channel and press the coloured button on your remote corresponding to the classification of the channel For example if you press the Red movie button the channel is designated as Movie Favourite channels A red heart will appear behind the channels name If the Red button is pressed again the selected channel is un selected from Movie Favourite list lt Please see inside cover Screen 4 gt 6 One channel can be saved into more than one Favourite list You can change selected Favourite channels in Favourite Organizer menu 7 Press the Back button until you go back to main menu You can view the Favourite list you set by pressing the Fav button while you are watching TV or listening to a Radio channel www strongsat com 10 PART 1 e English STRONG DIGITAL TV Editing Channels from the channel list You can change the channel name lock a channel and change the skipping functions Change name of channel To change the name of the channel please apply the following steps 1 Press the Menu button Using UP DOWN keys select Channel Organizer and press OK Using UP DOWN or P P keys select the channel Press the Yellow Edit button lt Please see inside cover Screen 2 and 5 gt Press OK on the channel name and the keyboard will appear on screen lt Please see inside cover Screen 6 gt Use UP DOWN or P
7. lt STRONG DIGITAL TV j E FIST NEI SE ME AU PELE NE LIE WL SSL AAA if F A ATT GUS R e y G O EE oe fF M E HE m 8 m 3 FS m 2 SS SO r Pe id lt r Digital Free to Air Satellite Receiver SRT 6130 User Manual www strongsat com STRONG O Dami Damm o 6130 orto CAE L J Ja 3 1 Figure 1 Figure 4 Figure 5 Figure 3 Figure 6 Figure 7 Figure 8 O Ore EO O y EER CS Figure 10 Figure 11 Figure 12 STRONG oom E mas DIGITAL TV Te SO Figure 13 PART 1 e English STRONG DIGITAL TV Thank you for choosing this Strong satellite receiver This receiver is of our latest development and it is designed to be capable of safely install your receiver and to achieve its optimum performance 1 0 Usage This user manual is applicable for Strong SRT 6130 Digital Satellite Receiver and its related accessories It is advised that first time and experienced users read this manual in order to safely install the receiver Strong has supplied this product with the m
8. of the OSD menu to Basic Colour 1 or Colour 2 m Transparency Press OK or the Right button and select how transparent you want your OSD m Brightness Press OK or the Right button and select how you want the OSD to be m OSD Timeout Press OK or the Right button and select how long you want the information banner to be on the screen when starting up your receiver or when changing channels 2 Press BACK until you go back to main menu m Time setting The system uses GMT Greenwich Mean Time as a default To set the time apply the following steps lt Please see inside cover Screen 15 gt 1 Select Time Settings and press OK or the Right button m Select Time Zone Press OK or the Right button and a list of the GMT plus or minus the hours you need for your country is displayed Using UP DOWN keys select the correct one and the receiver will automatically show the current time in your country To set the time manually m Select GMT usage Press OK or the Right button and use the UP DOWN buttons to set the GMT usage to off Press OK to save your setting The time setting menu will now activate the bottom two fields of the menu m Select Set Local Time Press OK or the Right button Use your UP DOWN buttons or Numeric buttons 0 9 to set the local time When set press OK to save the local time m Select Set Date Press OK or the Right button and set the date the way you have set the time www strongsat com 13
9. satellites IT download the channels please refer to Channel Set up Described in section 5 1 4 3 www strongsat com STRONG PART 1 e English DIGITAL TV 5 0 Basic settings Note Every time the receiver asks you to put your PIN code enter 0000 on your remote control using 0 9 numeric keypads Remember To switch between the TV Radio channels list you will have to press the TV RAD buttons on your remote accordingly 5 1 Main Menu Please see inside cover Screen 1 All the important settings and features of your receiver can be operated from the Main Menu The Main Menu consists of several sub menus such as Channel Organizer Favourite Organizer Timer Installation and Games To display and navigate through the main menu of the receiver please apply the following steps 1 Press the Menu button 2 Use UP DOWN keys to navigate through the menu 3 Press OK button every time you select an item from the menu 4 Press the BACK button to terminate an operation 5 Press the BACK button until you go back to main menu Tip Always read the Help bar displayed at the bottom of your screen 5 1 1 Channel Organizer Menu The Channel Organizer menu enables you to sort channels make your own Favourite channels list edit channel names and delete channels from the list Sorting Channels from the channels list To sort your channels please apply the following steps 1 Press the Menu button
10. you can choose a satellite from which you want to download your channels from by pressing OK lt Please see inside cover Screen 20 gt Tip If you want to rename the satellite press the button on the remote control when you are in the list of satellites m LNB Select LNB and press OK or the Right button In the LNB field select one of the available LNB s If you want to set LNB related values press OK and the LNB Set up menu Described in section 5 1 4 2 will be displayed m Dish Position Select Dish position and press OK or the Right button It displays the dish position of the current satellite When you use a DiSEqC 1 2 positioner you can select dish position in this field To set a dish position the status must be On in case the position has already been set or Off in case the position has not been set Note If in the LNB Set up menu described in section 5 1 4 2 the LNB Dish item is set to fixed you will not be able to change the dish position settings in the channel set up menu Only when you have selected the LNB Dish to moved you will be able to change the settings in the channel set up menu m Press OK button to set dish position The Positioner Set up menu will be displayed Detailed description is in Positioner Set up section 5 1 4 3 1 m Frequency Polarization Symbol Rate Shows the transponder TP values of the current satellite To change the value apply the
11. DiSEqc 1 0 switch to the LNB IN connector at the back of your receiver 3 2 3 Connecting a dish on a motorized positioner to your receiver Please see inside cover Figure 13 Another possibility of watching programs from multiple satellites is by mounting a dish to a motorized DiSEqc 1 2 positioner m Have your Strong dealer mount the dish to the positioner with the correct azimuth angle of elevation and let him set the centre point for your positioner m Connect the LNB with a coaxial cable to the LNB IN connector of the positioner m Connect the OUT connector of the positioner to the LNB IN connector at the back of your receiver 4 Starting up Ensure that your satellite receiver is correctly connected to your television and dish and that your satellite signal is of good quality Ifyou are not sure about this then ask your local Strong dealer to check your installation or satellite signal 4 1 Starting up for the First Time To offer you the best service we have already pre programmed the TV and Radio channels from the Astra 19 East and Hot Bird satellites into our receivers However it may be that for some countries the channels are not pre programmed The pre pro grammed channels are for ASTRA first then HOTBIRD m IF dish is on ASTRA The receiver will start up with channel 1 channel from ASTRA m F dish is on HOTBIRD NO SIGNAL message will appear Use the SAT button on your remote control to select HOTBIRD 4 2 Dish aimed at other
12. P keys to select a letter and the OK button to overwrite the current channel name letter by another letter Go up with the cursor into the line of the new name and press OK to confirm the changed name Press BACK to go back to the menu nu R w N Change lock function If you lock a channel you can only watch it from the TV list after entering your PIN Code To change lock function apply the following steps 1 Apply the first four steps detailed in Change name of channel described in section 5 1 1 2 Using UP DOWN or P P keys select Lock field lt Please see inside cover Screen 7 gt 3 Press OK and enter your PIN Code 4 The lock function will be marked 5 Move your cursor to the OK field and press the OK button 6 To unlock the channel repeat the same procedure Change the Skip function If Skip function is activated the channel will be skipped when you are scrolling through the TV list in normal watching mode Please apply the following steps 1 Apply the first four steps detailed in Change name of channel Described in section 5 1 1 2 Using UP DOWN or P P keys select Skip field lt Please see inside cover Screen 8 gt 3 Press OK and enter your PIN Code 4 The skip function will be marked 5 Move your cursor to the OK field and press the OK button 6 To unlock the channel repeat the procedure Change Video Package Identifier V PID Audio A PID Program P PID Values 1 Apply the first four st
13. PDIF function on Main menu gt Installation gt PIN code 0000 gt TV VCR Settings gt SPDIF Output gt On www strongsat com PART 1 e English STRONG DIGITAL TV 3 1 6 Connecting a serial cable for downloading software Please see inside cover Figure 10 m Connect the RS 232 connector on the back of your receiver to the Serial port of your computer using a serial cable m Instructions on how to download software can be found on our website www strongsat com support gt downloads However this receiver can download new system software automatically by satellite 3 2 Connecting to a satellite dish 3 2 1 Connecting a fixed satellite dish to your receiver Please see inside cover Figure 11 m Make your choice of satellite from which you want to receive your TV Radio channels m Have your Strong dealer align your dish at the requested satellite m Connect a coaxial cable to your LNB m Connect the other end directly to the LNB IN connector of your receiver 3 2 2 Connecting multiple fixed dishes to your receiver using a DiSEqC1 0 switch Please see inside cover Figure 12 If you want to watch programs from more than one satellite For instance from Astra and from Hot Bird it is advisable to use fixed dishes and a DiSEqC 1 0 switch m Have your Strong Dealer aim the dishes at the requested satellites m Connect the LNB s with coaxial cables to the IN connectors of the DiSEqC 1 0 switch m Connect the OUT connector of the
14. Receives QPSK Satellite Broadcasting F Signal and Decodes the Digitally Encoded Signal m Digital Tuner with Loop through output m SCPC MCPC Receivable from C KU band Satellite m MPEG 2 Main Profile at Main Level m Teletext 800 pages memory m Channel Memory about 2900 Digital TV Channels about 1400 Radio Channels www strongsat com STRONG PART 1 e English DIGITAL TV m Supports software downloading via satellite O T A m S PDIF output for connection with a digital audio amplifier Accessories m User s Manual m Remote contol unit m 2x Batteries AAA type Note The batteries should not be recharged disassembled electrically short circuited or be mixed or used with other types of batteries 1 3 Safety Precautions To maintain your receiver s optimum performance you are advised to apply the following safety precautions m Read this manual carefully and make sure you fully understand the instructions given m Refer all maintenance or servicing to suitably qualified personnel m f you wish you may clean your receiver with a soft lint free cloth slightly made damp with a mild soap solution only after disconnecting from the mains voltage supply m Do not use alcohol or ammonia based liquids to clean the receiver m Do not open the receiver cover as you will be exposed to a shock hazard m Do not open the receiver cover this will void your warranty m Do not place any objects on top of the receiver because this might preve
15. analyser and adjust your dish correctly Once the weather is better the picture will appear If not check if there is no snow on your dish Press the SAT button on the RCU and select the correct satellite Check settings in LNB and Channel set up menu Ask your dealer to check the outdoor unit and antenna cable to LNB Disconnect the 220V main power and ask your dealer to check the LNB cable Check whether the batteries are inserted correctly in your remote con trol Check the batteries and if they are exhausted replace them 20 www strongsat com PART 1 e English STRONG DIGITAL TV A 2 Glossary of terms C band DiSEqC EPG Fixed Dish Free To Air broadcast Ku band LNB MPEG Network PAL Parental lock 3 7 4 2 GHz Frequency Digital Satellite Equipment Control Electronic program guides that are transmitted by a broadcaster from a particular satellite to display information guide about a program content A dish antenna that is aimed at one particular satellite Unscrambled broadcast which you can view for free 11 18 GHz Frequency Low Noise Block down converter The LNB is an electronic unit mounted on the satellite dish It receives the signals reflected by the dish and converts them to signals that can be used by Satellite receiver The Moving Picture Experts Group is founded by the ISO MPEG is a standard method for digital trans mission of video and audio A networ
16. displays the message No or Bad signal The RED and Green lights on the front panel of your receiv er are blinking The remote control is not working Cause The power cord is not plugged in TV is set to wrong channel Problem in cable connections between receiver and TV Receiver hang up The receiver or TV is in MUTE mode Problem in scart cable connections between receiver and TV Wrong alignment of the dish This is normal the bad weath er is interfering the signal between the satellite and your dish Wrong satellite selected in the menu Wrong parameters set in the menu Wrong alignment of the dish Overload of the maximum available LNB power Short circuit in the LNB cable The batteries of the remote control are not inserted or exhausted Solution Check that the power cord is plugged into the wall outlet Check if the TV is switched on and set your TV to the correct EXT AV or UHF channel Check if the scart and or RF cable is connected correctly to the TV and to the back of the receiver Switch off receiver disconnect the main power cord of the receiver from the 220 V main power After 30 seconds reconnect to the main power and check if it is working properly Press the MUTE button on the remote control unit of your receiver and TV Firmly press the scart connectors on the backside of the TV and receiver Replace the scart cable Check the signal strength with a spectrum
17. el Organizer Menu Favourite Organizer Menu The Timer Menu The Installation Menu System Set up Menu LNB Set up Channel Set up Positioner Set up Parental Lock Changing PIN Code Games Basic functions Remote controle Trouble Shooting Glossary of terms Adu yu NNN O O WO WO CO CO CO 00 vo w 10 10 10 12 12 12 12 14 15 16 17 17 17 20 21 www strongsat com PART 1 e English STRONG DIGITAL TV 1 1 Safety Instructions Warning DO NOT INSTALL YOUR RECEIVER m In a closed or poorly ventilated cabinet m Directly on top of or under any another equipment m On a surface which might obstruct the ventilation slots DO NOT EXPOSE THE RECEIVER OR ITS ACCESSORIES m To direct sunlight or near any other equipment that generates heat m To rain or intense moisture m To any shock which may cause permanent damage to your receiver m To any magnetic objects such as loudspeakers transformers etc m To intense vibration m Never open the cover It is dangerous to touch the inside of the receiver due to high voltage currents and possible electrical hazards Your warranty will be void if the receiver has been opened m When the receiver is not used for a long period of time you should unplug the power cord from the wall socket m Do not use a damaged power cord It may cause a fire or an electrical shock m Do not touch a power cord with wet hands It may cause an electric shock m Place t
18. eps detailed in Change name of channel described previously 2 Using UP DOWN or P P keys select PID field lt Please see inside cover Screen 8 gt 3 Using the numeric keypad 0 9 enter the new value 4 Move your cursor to the OK field and press the OK button Deleting Channels from channel list You can delete channels from the channel list by applying the following steps 1 Press the Menu button Using UP DOWN keys select Channel Organizer and press OK Press the Blue Delete button lt Please see inside cover Screen 2 gt Using UP DOWN or P P keys on your remote select the channel Press the Red button to delete the selected channel Press the Green button to delete all channels from the list Press the Yellow Button to exit the delete menu N DW R WN www strongsat com 11 STRONG PART 1 e English DIGITAL TV 5 1 2 Favourite Organizer Menu This menu enables you to organize your Favourite channels list All the channels that you have marked as your Favourite in the Channel organizer menu can be sorted by applying the following steps 1 Press the Menu button lt Please see inside cover Screen 1 gt 2 Using UP DOWN keys select Favourite Organizer and press OK lt Please see inside cover Screen 9 gt m Sort Red button Same as the Sort function of Channel Organizer menu lt Please see inside cover Screen 3 gt m NxtFav Next Favourite Group Green button Shows the next Favou
19. er is connected to the satellite signal Do not turn off your receiver while you are downloading new software m System Information The system information displays information about your receiver such as model number soft ware and boot version To check system information apply the following steps 1 Select System information and press OK or the Right button lt Please see inside cover Screen 18 gt m Factory Reset Be careful when using this function because it will erase all the data and parameters you may have set earlier to your receiver Once you have made a Factory Reset you will have to re install your preferences and re scan your channels To reset your receiver to factory default apply the following steps 1 Select Factory Reset and press OK 2 Enter your PIN Code The receiver will reset itself to the original factory settings Note Your PIN code will change back to the factory setting 0000 5 1 4 2 LNB Set up Please see inside cover Screen 19 It is recommended that you read the manual and installation instructions of your LNB your DiSEqC switch your Positioner before you start setting up your LNB To set up your LNB please apply the following steps 1 Press the Menu button 2 Using UP DOWN keys select Installation and press OK 3 Using UP DOWN keys select LNB Set up and press OK 4 Check the exact specifications of your LNB through the manufacturers information or your dealer There are up to 16 types
20. ess OK www strongsat com 12 PART 1 e English STRONG DIGITAL TV m Language Settings You can change the language of the menu audio and subtitles by applying the following steps lt Please see inside cover Screen 12 gt 1 Select Language Settings and Press OK or the Right button 2 Select Menu Language and Press OK or the Right button 3 Using UP DOWN keys select the language in which you want your menu to be displayed and press OK The screen of the menu will change to the language of your choice 4 You can also choose your preferred first audio language second audio language and the subtitle language by applying the same steps 5 Press BACK until you return to the main menu m TV VCR Settings lt Please see inside cover Screen13 gt You can set the TV VCR settings to your personal prefer ences Check your TV and VCR user manuals for the correct settings You can change your TV VCR settings by applying the following steps 1 Select TV VCR Settings and press OK or the Right button m TV Mode Press OK or the Right button and set your TV mode to Multi PAL or NTSC m Video Mode Press OK or the Right button and set your VCR mode to CVBS Composite video or RGB preferred option if your TV set is compatible with it m Screen Mode Press OK or the Right button and set your screen mode to 4 3 Full Screen 4 3 Letter or 16 9 m Audio Output Press OK or the Ri
21. f the wall outlet before connecting your receiver to the main power www strongsat com STRONG PART 1 e English DIGITAL TV 3 0 Connections 3 1 Connecting to your TV amp VCR Warning If you are not sure how to connect your receiver do not take the risk of doing it yourself Ask your Strong dealer to do it for you They are specially trained by our technicians and can get the best performance out of your receiver Although there are entechnologies and requires specialised equipment Do not hesitate to ask any questions you have to your Strong dealer about installing your receiver It is possible to connect the receiver through the use of UHF coaxial cables SCART cables and or so called Audio Video cables with RCA connectors 3 1 1 Basic connection with a coaxial cable Please see inside cover Figure 4 m Connect the satellite signal from the LNB to the LNB IN connector m Connect the To TV connector at the back of the receiver to the ANT IN connector on your TV set m Optional connect a UHF coaxial or cable coming from your antenna or cable TV to the ANT input connector at the back of the receiver 3 1 2 Basic connection with a Scart cable Please see inside cover Figure 5 m Connect the satellite signal from the LNB to the LNB IN connector m Connect the TV scart connector at the back of the receiver to the scart in connector on your TV set m Optional connect a UHF coaxial or cable coming from your antenna or cable TV to
22. following steps 1 Select Frequency and press OK The list of TP values of the current satellite is displayed 2 The functions of the coloured buttons are switched to represent other functions lt Please see inside cover Screen 21 gt 3 To edit a TP value press the Red Edit button 4 To change the current TP value press the Blue Add button 5 Press the Yellow Save button to save the settings 6 Press the Blue Delete button to delete the current TP value Save is only available in the Edit mode or the Add mode m Scan Mode Designate channels scanning whether FTA Free to Air only or All channels including scrambled channels m Network Search Set this field to On to perform Network TP Search m AutoScan Red Button This function searches all the transponders of a satellite m Net Scan Green Button Network Search Performs network search for a transponder m TP Scan Yellow Button Search channels from current specific transponder m PID Blue Button You can search a specific channel by entering the PID value of a channel If you press the Blue PID button the PID screen is displayed Enter the PID value and press the Blue button again To cancel the PID value press Back on the remote control or press the Blue PID button to search the channel You should enter V PID A PID and P PID as described in Editing channels from the channel list Described in section 5 1 1 lt Please see in
23. ght button and set your audio output to Stereo Left only or Right only left or Right is for mono TV sets m SPDIF Output Press OK or the Right button and activate your S PDIF output on the back of your receiver so you can connect it to a digital Audio amplifier using a coaxial cable m VCR Scart Press OK or the Right button and set the scart output to Auto or STB Set Top Box If set to STB the VCR scart signal is not automatically looped through m UHF Mode Press OK or the Right button and set the UHF mode to PAL B G PAL or PAL D K If the TV set is connected using a coaxial RF cable you must select RF modulator type here The RF modulator type affects the channel audio Select PAL for UK NI or ROI use m UHF Channel Press OK or the Right button and set the UHF channel number to the same UHF channel number of your TV set This only has to be done if your TV set is connected with a coaxial RF Cable If the UHF Channel numbers of the receiver and the TV set are not set the same no picture will be displayed 2 Press BACK until you go back to main menu m OSD Settings You can set the OSD On Screen Display on your TV to your personal preferences You can change the OSD settings by applying the following steps 1 Select OSD Settings and press OK or the Right button lt Please see inside cover Screen 14 gt m Colour Scheme Press OK or the Right button and set the colours
24. he receiver in a well ventilated environment m When you are connecting the cables be sure that the receiver is disconnected from the mains supply voltage m Do not use your receiver in humid environment Make sure you read this user manual before installing your receiver This manual provides complete instructions for installing and using this receiver The following symbols will be used as follows Bold Characters Represents a button on the remote control or the receiver Italic Characters Represents a menu item within the On Screen Display OSD Menu 1 2 Features 8 Accessories SRT 6130 Digital Satellite Receiver m Easy to use Graphic MENU Interface m Multi lingual support on screen Menu English German French Italian Spanish Dutch Russian Turkish Swedish Slavic Slovak Hungarian Czech Bulgarian Romanian Lithuanian Latvian Polish m RS 232 port for updating control software and additional services m Supports DiSEqC 1 0 1 1 1 2 m 2 SCART Connectors TV VCR m 3RCA Connectors CVBS Audio Left Right m Multi Language function Menu Audio m Front Panel Buttons m Editing Functions TV or Radio Channel Channel Name PID Transponder Name m EPG Electronic Program Guide for on screen channel information m Over 4000 channels memory capacity m Memory for Multi satellite reception up to 64 m Four Favourite lists for both TV and Radio m 3 Operation Modes Digital TV Digital Radio Favourite u LNB 13 18 V 0 22 KHz Tone m
25. k which is also known as a bouquet is a set of channels that is offered by a single broadcaster Reffering to the Phase Alternate Line colour system adopted by European broadcasters This function gives you the possibility to lock other several functions of the receiver to prevent unau thorized users such as children to view channels that are not suitable for them A PIN code is required to use of the parental lock PID The transmitted packages have identifiers PID that tells the receiver what to do with the received information Satellite receivers normally use four types of PID these are V PID video PID A PID audio PID P PID Program PID and data PID EPG information PIN Code Personal Identification Number A four digit code that is used for locking unlocking e g with the parental control feature Polarization Allows several programmes to be fitted into the same frequency band The signals from a satellite are transmitter either with linear vertical or horizontal polarization or circular right or left polarization RS 232 Serial data port www strongsat com 21 STRONG Technical Specifications DIGITAL TV Technical Specifications Demodulator Video Decoder Audio Decoder Tuner RF Modulator System amp Memory General Data Modulation QPSK Input Symbol Rate 2 45 Ms s SCPC amp MCPC signals from C amp KU band satellites MPEG 2 Main profile Main level Input Rate Max 60 Mbi
26. lect the game you want to play and press OK 6 0 Basic functions Remote control All features of the set top box can be controlled with the remote control Inserting batteries to the Remote Control Unit 1 Open the battery cover on the rear of the remote control Unit 2 Insert the two supplied batteries 1 5V observing the polarity and the AAA specification 3 Firmly replace the battery cover While viewing TV or Radio channels various functions can be applied using your remote control Outlined is an explanation of the buttons on your Remote and their corresponding functions that can be performed while watching TV or listening to the Radio See inside cover for the illustration of the remote control 1 STANDBY ON OFF Switches the Receiver ON or OFF 2 SUB Shows the list of subtitle languages the current channel supports You can change the subtitle language you want by using the UP DOWN keys and pressing OK on your remote 3 TEXT Enables Teletext www strongsat com 17 STRONG PART 1 e English DIGITAL TV 4 SAT Displays the list of satellites you have scanned with your receiver You can change the satellite you want to watch by using the Up Down keys and pressing the OK button The channel list is configured with the channels searched in that satellite If you have set up a motorized positioner to change the satellite a message wait moving dish is displayed The SAT button is disabled in the favou
27. nel supports EPG If you press EPG the Weekly mode is displayed as default m Weekly Red Button The current TP channel list is displayed on the left and the event information is displayed on the right by time zone lt Please see inside cover Screen 27 gt m Daily Green Button If you want to display the Daily mode of the current channel press green Daily In the daily mode the receiver shows the designated channel in PIG and displays the channel event in detail lt Please see inside cover Screen 28 gt m Extended Yellow Button If you press the Yellow button the receiver shows the detailed information of the current event lt Please see inside cover Screen 29 gt m Timer Blue Button Move the cursor to an event in the required time zone and press Blue Timer The timer is then set to the designated time See Timer Menu Described in section 5 1 3 for details of the timer m Press BACK to close the EPG menu 16 PAUSE Freezes the picture 17 AUDIO Shows the list of available audio languages for the channel you are watching You can change the audio language you want to hear by using the UP DOWN keys and pressing the OK button In addition it sets the current channel audio to stereo 0 left mono o or right mono o Pressing the sound button changes the sound icon on the top banner The selected sound information is saved by channel and is set to the sound mode when you watch the channel www strongsat com 18
28. nnector Use this connector to connect your receiver to your video recorder using a scart cable Your video signal will now be looped through to your TV 7 RS 232 Serial Port This serial port can be used to connect your PC to your receiver and enables you to download new versions of software into your receiver Detailed information about downloading software into your receiver can be found on our website www strongsat com Note It is recommended to ONLY use the original software provided via our website Loading other versions of software not adapted to your model number can cause severe damage to your receiver and will not be covered by the warranty 8 Input Antenna Female part Ifyou have cable TV or if you have an outdoor antenna then you can connect the RF cable coming from the antenna or wall connector to this ANT input If you use a scart cable to connect the receiver to your TV the additional antenna can be put directly into your TV 9 To TV Male part RF Modulator If you do not use a scart cable to connect your receiver to your TV or ifyou have connected a cable to the ANT input you will have to use this connector to connect the receiver to your TV by using a coaxial cable 10 S PDIF Use this coaxial output to connect your receiver to the input of your digital audio amplifier 11 Power Cord Your receiver requires a mains voltage supply of 90 240V AC Auto selectable 50 60Hz 5 Make sure to check the power specification o
29. nt proper cooling of the components inside m Make sure no foreign objects fall through the ventilation slots because this could cause fire or an electric shock m Wait a few seconds after switching off the receiver before you move the receiver or disconnect any equipment m Please ensure that that the electrical power supply corresponds with the voltage on the electrical identification plate at the back of the receiver m It is a necessity that you only use an approved extension and compatible wiring that is suitable for the electrical power consumption of the installed equipment m f the receiver does not operate normally even after strictly following the instructions in this user manual it is recommended to consult your dealer 1 4 Storage Your receiver and its accessories are stored and delivered in a well protective packaging against electric shocks and moisture When unpacking it make sure that all the parts are included and keep packaging away from children When transporting the receiver from one place to another or if you are returning it under warranty make sure to store the receiver in its original packaging with its acces sories Failing to comply with such packaging procedures could void your warranty 1 5 Equipment Set up We recommend you to consult a professional installer to set up your equipment Otherwise please follow the following instructions m Refer to the user manual of your TV and dish m Make sure that the SCART cable is in
30. of LNB s available The Default is set to Universal mode 9750 10600MHz DiSEqC is not used and the LNB is mounted on a fixed dish 5 Use the UP DOWN keys on your remote to select an item and use the LEFT RIGHT buttons to set up any values m LNB Up to 16 LNBs are available select the correct one according to your LNB specifications m LNB Type Select the LNB type from Universal 1 3 and Single You should type the LNB value in Single In Single the item parameter is O or another number In UNI1 9750 10600 MHz UNI2 9750 10700MHz UNI3 9750 10750 MHz m LNB Power Select 13 18V 13V or 18V for LNB Select Off if you want to switch the power of the LNB off m LNB Dish Using the Left Right buttons select Fixed or Moved Dish If you use a motorised dish read the Positioner Set up Described in section 5 1 4 3 1 m DiSEqC switch The default is Off To use the DiSEqC switch set up the DiSEqC version you have V1 0 or V1 1 m DiSEqC Input Select position 1 4 if DiSEqC switch is DiSEqC V1 0 Select position 1 16 if DiSEqC switch is DiSEqC V1 1 m DiSEqC Repeat Designate the repeat of switching 0 3 m Switch 22 kHz You can set the 0 22kHz switch to ON or OFF www strongsat com 14 PART 1 o English STRONG DIGITAL TV If you set LNB type to Universal UNIT UNI3 you will not be able to change settings in both the LNB Power menu item and the Switch 22 kHz menu item If you want to
31. or will help you set up the best dish position possible Use your UP DOWN buttons to select the Dish Position field in the Channel Set up menu Press the OK button and the Positioner Set up Menu will be displayed Start setting the position of the selected satellite Use your UP DOWN buttons to go to field Centre and use your Left Right buttons to put the centre field to On Press OK and your dish will move to the centre position It takes your dish maximum 30 seconds to move to its central position 9 To know in which direction you will need to move your dish you will need to know the position of the satellite you want it to position to 10 If correctly installed your installer has set the centre position of your dish to the true South if in the Northern hemi sphere and to true North if in the Southern Hemisphere 11 If for instance you want to set the position for Astra 19 2 East you know that you will have to move your dish to the left using the Left button If you want to set the position for instance to Eutelsat 12 5 West you know that you will have to move your dish to the right using the Right button As viewed from the rear of the dish 0 So u A To set the position of your selected satellite 1 Use your UP DOWN buttons to go to the Movement field 2 Use your Left Right buttons to have your dish turn towards the right direction and keep this direction button pushed in continuousl
32. ost recent innovations of software and hardware Strong reserves the right to make changes in production to the software used by your satellite receiver without prior notification In order to maintain and ensure that your receiver is compatible and updated with the most recent software technology we recommend that you visit our website to check the latest software www strongsat com STRONG PART 1 e English 1 1 1 2 1 3 1 4 1 5 2 0 2 1 2 2 3 0 3 1 3 1 1 3 1 2 3 1 3 3 1 4 3 1 5 3 1 6 3 2 3 2 1 3 2 2 3 2 3 4 0 4 1 4 2 5 0 5 1 5 1 1 5 1 2 5 1 3 5 1 4 5 1 4 1 5 1 4 2 5 1 4 3 5 1 4 3 1 5 1 4 4 551 5 6 0 Al A 2 DIGITAL TV Safety Instructions Features amp Accessories Safety Precautions Storage Equipment Set up Your Receiver Front Panel Rear Panel Connections Connecting to your TV amp VCR Basic connection with a coaxial cable Basic connection with a Scart cable Advanced connection Connection with Audio Cable RCA Connectors Connection to a digital audio amplifier using the S PDIF output Connecting a serial cable for downloading software Connecting to a satellite dish Connecting a fixed satellite dish to your receiver Connecting multiple fixed dishes to your receiver using a DiSEqC1 0 switch Connecting a dish on a motorized positioner to your receiver Starting up Starting up for the First Time Dish aimed at other satellites Basic settings Main Menu Chann
33. ote select Installation and press OK 3 The receiver will ask you to put your PIN code This PIN code is currently set to 0000 4 Using UP DOWN keys select Parental lock and press OK 5 Using RIGHT LEFT keys you can select either lock or unlock and press OK By selecting lock the receiver asks you to enter your PIN every time you want to access the menu By selecting unlock it gives you the possibili ty to access the menu all the time without the receiver asking you for a PIN code m To change your PIN code apply the following steps 1 Press the Menu button on your remote Using UP DOWN keys select Installation and press OK Using UP DOWN keys select Parental lock and press OK Using UP DOWN keys select Old PIN and enter 0000 Using UP DOWN keys select New PIN and enter a new PIN Using UP DOWN keys select Verify PIN and enter the same new PIN Press the Green button on your remote to save amp Exit ON DUN A w N Press the Back button until you go back to main menu You are recommended to write down your new PIN code In case you forget it you can reset your receiver to factory default settings but you will lose all information you saved Your Personal PIN Code 5 1 5 Games If you want to play a game apply the following steps 1 Press the Menu button on your remote 2 Using UP DOWN keys on your remote select Games and press OK 3 Using UP DOWN keys on your remote se
34. rite channel mode because there can be a number of different satellites on which you have different favourite channels 5 Mute Enables or disables the sound Mutes 6 TV RAD Switches between TV or Radio mode 7 FAV Displays the list of favourite channels If you press FAV on the remote control in No menu state You can preview the chan nel via PIG Picture in Graphic and move through the list of channels quickly with the CHANNEL UP CHANNEL DOWN buttons 8 CHANNEL Up Down Used for stepping through the channels or navigating within the OSD Menus 9 VOL Left Right Used for adjusting the volume or for navigating within the OSD Menus left right In channel list as well as in satellites and TP lists used to scroll list prev next 10 items duplicate Page Page buttons 10 OK To confirm actions in the menu systems In view mode displays the current channel list For example TV Radio or Favourite 11 MENU The main menu for setting up the receiver 12 BACK Exits the current OSD page In TV mode switches back to previous channels 13 AV Selects TV or Digital TV 14 Information lt Please see inside cover Screen 26 gt Shows program information 15 EPG Display the EPG Electronic Program Guide EPG shows the event information on the current TP channel by time zone EPG is divided into Weekly mode Daily mode and Extend mode It provides timer based recording and automatic power ON Off The event is displayed only if the chan
35. rite group list m Edit Yellow button You can edit the name of the favourite group in the same way as you change a channel name in the Channel Organizer Menu lt Please see inside cover Screen 6 gt m Remove Blue button Removes the selected channel directly from the Favourite list that was selected 5 1 3 The Timer Menu The timer can automatically switch on or off your receicver at any time This enables you for example to record programmes with your VCR while you are not at home It also can be used to wake you up at the time you set it Please apply the following steps 1 Press the Menu button lt Please see inside cover Screen 1 gt 2 Using UP DOWN keys on your remote select Timer Menu and press OK lt Please see inside cover Screen 10 gt m Timer number You can select up to 8 different events m Timer State Set to Enabled to use the timer function or Disable to stop the timer functions of the timer num ber you selected m Timer mode You can select the following functions in the timer mode 1 Power On The receiver powers on at the designated date and time 2 Time interval The receiver switches on at the designated date and time displays the channel and then switches off at the designated date and time The value set at the ending time 3 Power Off The receiver powers off at the designated date and time Press OK now you will see the channel list select a channel and Press OK m Timer Cycle Yo
36. side cover Screen 23 gt www strongsat com 15 STRONG PART 1 e English DIGITAL TV Tip Check the level and quality of the signal bar before searching any channels The signal level of the TP of the current satellite is displayed The green bar is displayed if the settings are correct otherwise the red bar is displayed and you cannot get the channel In the latter case check if your dish is aimed at the selected satellite or if the DiSEqC switch of the LNB overlaps with another satellite Also change the Frequency with the Left Right button until the Green bar is displayed to get the valid transponder If you press the Red Auto Scan Green Net Scan Yellow TP Scan or Blue PID button the channel search ing status is displayed lt Please see inside cover Screen 22 gt 5 1 4 3 1 Positioner Set up if you are using a Motorised positioner with DiSEqC1 2 Please see inside cover Screen 24 If yfunction is available only if in the LNB Set up menu and the LNB Dish field is set to Moved As described in LNB Set up Described in section 5 1 4 2 Before you start 1 Make sure that your installer has set the centre position of your dish 2 Make sure that the mechanical limits of your motor are set so that no damage can be done to your dish by moving it too far to the East West 3 Make sure you set the highest Symbol Rate Ksymbols sec for your chosen transponder TP The Signal level and Quality indicat
37. t s Video Resolution 720 x 576 PAL 720 x 480 NTSC Aspect Ratio 4 3 16 9 Pan amp Scan Letter box MPEG MusiCam Layer I amp II Audio mode Stereo Dual Channel Mono Joint Stereo Mono AC 3 Input Frequency Range 950 2150 MHz RF Input Level 25 65 dBm LNB Power 13 18 V DC Max 600 mA Overload protected DiSEqC Version 1 0 1 2 Channels 21 69 for TV without Scart Output PAL G I K Main Processor STi 5518 Flash Memory 2 Mbytes SDRAM 8 Mbytes EEPROM 64 kBits Input Voltage Range 90 240 V AC SMPS 50 60 Hz Power Consumption Max 25 W Standby Power consumption 13 W Operating Temperature 5 C 45 C Storage Temperature 0 C 50 C Size WxHxD in mm 280 x 40 x 190 Weight 2 kg Technical alterations reserved www strongsat com
38. the ANT input connector at the back of the receiver 3 1 3 Advanced connection Please see inside cover Figure 6 m Connect the satellite signal from the LNB to the LNB IN connector m Connect the TV scart connector at the back of the receiver to the scart in connector on your TV set m Connect the VCR scart connector at the back of the receiver to the scart in connector on your VCR set m Connect a UHF coaxial or cable coming from your antenna or cable TV to the ANT input connector at the back of the receiver m Connect a coaxial cable to the TV VCR connector at the back of the receiver Connect the other end of this coaxial cable to the ANT IN connector of your VCR m Connect the TV OUT connector of your VCR to the ANT IN connector of your TV set with a coaxial cable Note If you have a digital audio amplifier with a digital audio input use the S PDIF output 3 1 4 Connection with Audio Cable RCA Connectors Please see inside cover Figure 7 m On the back of your receiver you will find the RCA connectors Audio Left amp Right Red amp white Video Yellow m Install an audio video cable between the RCA connectors of the receiver and those of your TV set or amplifier 3 1 5 Connection to a digital audio amplifier using the S PDIF output Please see inside cover Figure 8 m Connect the S PDIF out connector on the back of your receiver to the S PDIF input connector of your digital amplifier using a coaxial cable m Do not forget to turn the S
39. u can set the cycle of the action designated in the timer mode one time Every Day or Every Week m Date You can set the starting date of the timer action m Time You can set the starting time of the timer action m Ending Time You can set the ending time of the channel view when the Timer mode is on Time Interval m Channel You can select the channel to be shown when the receiver timer mode Powers ON 3 Press the Red button to save and proceed with another timer event 4 Press the Green button to save and exit the timer menu 5 Press the Yellow button to exit the timer menu WITHOUT saving the settings Tip You have to select the channel starting time and ending time settings if the Timer mode is Time interval An error message will appear if any of the settings are incorrect 5 1 4 The Installation Menu Please see inside cover Screen 1 All settings that are related to TV Dish LNB and Satellites are within this menu The installation menu contains several sub menus such as System Set up LNB Set up Channel Set up and Parental Lock To access the different sub menus apply the following 5 1 4 1 System Set up Menu Please see inside cover Screen 11 To install your receiver to your personal preferences go to System Set up menu Then please apply the following steps 1 Press the Menu button 2 Using UP DOWN keys select Installation and press OK 3 Using UP DOWN keys select System Set up and pr
40. y Once the receiver has found the right position for the selected satellite the word Locked will appear above the signal level and quality indicator To be sure you have the strongest signal possible press the direction you moved your dish in once again and look if the signal quality improves If this is not the case move the dish back one position by pressing the other direction once 3 If you are sure that you have the strongest signal quality for the selected satellite m Use your UP DOWN buttons to go to the Save field m Use your Left Right buttons to set to On and press OK The position for the selected satellite is now saved and your dish will move to this position every time a channel from this satellite is chosen Repeat this procedure for every satellite position and once you have complete the settings Use Red Auto Scan Green Net Scan Yellow TP Scan or Blue PID to search channels www strongsat com 16 PART 1 e English STRONG DIGITAL TV 5 1 4 4 Parental Lock Changing PIN Code Please see inside cover Screen 25 This function changes the Personal Identification Number PIN that is used to control access to the menu and individual channels In this function you can lock unlock channels and you can change your PIN code by applying the following steps m To lock unlock the menu please apply the following steps 1 Press the Menu button on your remote 2 Using UP DOWN keys on your rem
Download Pdf Manuals
Related Search