U-STYLE STAND DIVING SYSTEM Assembly & Installation - Inter-Fab
Contents
1. 7 Installation Instructions Residential 8 Article 5 Extracted from ANSI NSPI 5 003 9 14 COMMERCIAL U Stand Base Placement Commercial 19 U Stand Specifications Commercial 19 Public Board Mounting Diagrarmn 16 Installation Instructions Commercial 16 Article 5 Extracted from ANSI NSPI 1 2003 17 25 Inter Fab Limited Warranty 26 U STAND IM Rev 3 09 BK USTAND BOOK 1 INSTALLATION MANUAL U STAND SAFETY FIRST This Inter Fab diving board and or stand shall be installed only by a professional swimming pool contractor or with the direct supervision of a licensed professional engineer or architect Diving boards may be installed only on residential or public inground swimming pools properly designed for their use Diving boards that are improperly installed can be very dangerous to the user resulting in possible serious head and or spinal column injury including the paralysis or death of the user It is very important that this diving board and or stand be installed only on residential inground pools which meet or exceed the minimum water envelope dimensions of the American Na2. DECK END WATER END A 2 FIG U STAND COMMERCIAL PLACEMENT SPECIFICATIONS rs DIVING BOARD FULCRUM PAD 1 1 2 B 4 INTO FULCRUM mec DIVING BOARD U FRAME oS SEE TABLE E DEE HOW FINISH GRADE 3 REBAR DECK LENGTH 8 MIN MODEL DECK THICKNESS 6 MIN DECK WIDTH 4 MIN DBU24065 A S 3 REBAR Y i gt CONCRETE 5 Li TABLE 7 U STAND MATERIAL T a suc oo wan MATERIALS 1 90 OD 065 WALL 304 STAINLESS STEEL INTER FAB CANNOT GUARANTEE CUSTOMER S NOTE ONLY 065 U STANDS CAN BE CONCRETE OR THICKNESS INSTALLED ON A PUBLIC POOL NOTE WHEN COPING IS USED DO NOT SET FRONT U STAND IMPORTANT NOTICE WHEN PROPERLY INSTALLED INTER FAB S 18 U STAND WILL HAVE 4 OF THE RAIL EMBEDDED WITHIN THE DECK AND WILL MEASURE 18 FROM CLOSER THAN 3 FROM THE BACK EDGE OF THE COPING THE TOP OF THE RAIL TO THE SURFACE OF THE DECK THE 24 U STAND IS DIFFERENT WHEN PROPERLY INSTALLED 4 OF THE RAIL WILL BE EMBEDDED WITHIN THE DECK TABLE 8 INTER FAB PUBLIC POOL SPECIFICATIONS AND IT WILL MEASURE 20 FROM THE TOP OF THE RAIL TO THE SURFACE OF THE DECK RELATED DIVING EQUIPMENT Placement of boards shall observe the following minimum dimensions MAX DIVING MAX BOARD a BOARD HEIGHT increased accordingly PENGIN OVE
3. 7 2 4 Public pools with diving equipment of 1 meter 39 inches or greater in height or pools de signed for springboard or platform diving shall com ply with the dimensional design requirements of Fed eration Internationale de Natation FINA U S Diving National Federation of State High Schools Association NFSHSA or the appropriate sanction ing body 7 2 5 Diving equipment Diving equipment shall be installed in accordance with the manufac turer s specifications 7 2 5 1 The diving equipment manu facturer shall affix a label to the diving equipment 7 2 5 2 label shall be permanently af fixed to the diving equipment or jump board and shall include but not be limited to the following The minimum water envelope re quired for each diving board and diving stand combination Manufacturer s name and address Manufacturer s identification and date of manufacture and The maximum weight of the user visibly located on the diving board 7 2 5 3 The diving equipment manu facturer shall provide diving equipment use instruc tions U STAND IM Rev 3 09 BK USTAND BOOK 24 7 2 5 4 Diving equipment shall have slip resisting tread surfaces 7 2 5 5 Supports for diving equip ment Supports platforms stairs and ladders for diving equipment shall be designed to carry the an ticipated loads Stairs and ladders shall be of corro sion resisting material and shall be easily cleanable and wit
4. DECK THICKNESS 6 MIN DECK WIDTH 4 MIN INTER FAB CANNOT GUARANTEE CUSTOMER S CONCRETE OR THICKNESS NOTE WHEN COPING IS USED DO NOT SET FRONT U STAND CLOSER THAN 3 FROM THE BACK EDGE OF THE COPING TABLE 5 RESIDENTIAL PLACEMENT CHART TABLE 3 U STAND SPECS TABLE 4 U STAND MATERIAL sur wan 30 oem NE MODEL IMPORTANT NOTICE WHEN PROPERLY INSTALLED INTER FAB S 12 AND 18 U STANDS WILL HAVE 4 OF THE RAIL EMBEDDED WITHIN THE DECK AND WILL MEASURE RESPECTIVELY 12 OR 18 FROM THE TOP OF THE RAIL TO THE SURFACE OF THE DECK THE 24 U STAND IS DIFFERENT WHEN PROPERLY INSTALLED 4 OF THE RAIL WILL BE EMBEDDED WITHIN THE DECK AND IT WILL MEASURE 20 FROM THE TOP OF THE RAIL TO THE SURFACE OF THE DECK ADDITIONALLY REFER ANSI NSPI 5 2003 American National Standard for Residential Inground Swimming Pools and to page 5 for Inter Fab Residential Inground Pool Minimum Specifications U STANDARDS IMPORTANT PART NOMINAL _ BOARD Note there are several sizes LENGTH THESE DIMENSIONS available for each pool type ARE ACCURATE ONLY DBU12049 DISTANCE FROM DISTANCE MIN MAX HEIGHT WATER S EDGE FROM END OVERHANG OF BOARD TO FORWARD OF BOARD PLUS OR ABOVE U STAND TO FORWARD MINUS 3 WATER S U STAND WA HOW 18 25 36 25 18 20 FOR VERTICAL POOL DBU12049 18 25 36 25 18 20 WALLS TYPICALLY 49 or DBU18 18 25 36 25 24 2
5. N 11 MAX REFERENCE DIAGRAM TO SCALE Figure 2 Maximum allowable wall slope Table 2 Minimum water envelopes Pool Minimum dimensions Minimum width of pool at type D R L L L L4 Ls Pt A Pt B Pt C T 0 8 6 5 6 2 6 8 0 10 6 7 0 28 0 16 0 8 0 18 0 VI 213cm 259 168 76 244 cm 320 213 cm 853 488 549 cm 549 cm T 6 9 0 6 0 3 0 9 0 12 0 4 0 28 0 18 0 20 0 20 0 229 274 cm 183 cm 91 em 274 em 366 cm 122 cm 853 cm 549 610 cm 610 cm 8 6 10 0 7 0 4 0 10 0 15 0 2 0 31 0 20 0 22 0 22 0 259 cm 305 213 cm 122 305 em 457 61 cm 945 610 em 671 cm 671 cm 11 0 12 0 8 6 6 0 10 6 21 0 0 37 6 22 0 24 0 24 0 IX 335 cm 366 cm 259 cm 183 cm 320 640 cm 11 4 671 cm 732 em 732 NOTE For definition of pool types see Glossar U STAND IM Rev 3 09 BK USTAND BOOK 21 INSTALLATION MANUAL U STAND SUPPORT INFORMATION 1 7 Extracted from ANSI NSPI 1 2003 American National Standard for Public Swimming Pools Table 3 Maximum user load Pool Deck area Shallow instruc Deep area Diving area tional not including the per each diving or wading areas diving area board Pools with minimum deck area 1
6. 5 0 2 9 15 0 118 0 115 0 9 0 3 0 9 0 I2 O Varies 16 0 36 9 Minimum lengths between points CD DE Minimum length between points CD may vary based upon water depth at point D and the slope between points C amp D Figure 3 drawings are not to scale For pool types see Glossary 5 5 Offset ledges 5 6 1 The slope of the floor from the shallow end wall towards the deep area shall not exceed 1 5 5 1 Offset ledges shall be a maximum of 8 inches 20 3 cm wide 5 5 1 1 Offset ledges located less than 42 inches 1067 mm below waterline shall be pro portionately less than 8 inches 20 3 cm wide and fall within 11 from plumb measured from the top of the waterline See figure 4 5 6 Floor slopes Floor slopes shall be reasonably uniform and comply with 5 6 1 through 5 6 3 TOP OF WALL WATERLINE TYPICAL PLUMB 42 A WALL SECTION 8 MAX OFFSET 1f MAX 1 5 SLOPE WALL sss VARIABLE es Qu SLOPE n 8 LEDGE 42 TO FLOOR BELOW WATER LEVEL REFERENCE DIAGRAM NOT TO SCALE Figure 4 Offset ledges U STAND IM Rev 3 09 BK USTAND BOOK foot in 7 feet 30 cm 213 cm to the point of the first slope change as shown in figure 5 5 6 2 Changes in slope between shallow and deep areas shall be at a minimum water depth of 2 feet 9 inches 83 8 cm and be at least six feet 182 9 cm
7. INSTALLATION FIG B U STAND BASE EXPLODED VIEW LE dz A 4 m s ka 7 b 3 8 9 10 r lt NO Rebar 1 L Not Included oni DRAWING REPRESENTS THE FOLLOWING PART NUMBERS DBU12049 shown DBU18049 DBU18065 08024049 08024065 TABLE 6 PARTS LIST TIGHTENING SCHEDULE Secure Board to Stand with Mounting Hex Nuts at 20 25 COMPONENT DESCRIPTION ET LBS DBU12049 12 U Style Diving Standards DB6WW 8 Duro Beam White w White Top Tread amp Hdw Kit FC Fulcrum Cover For U Standard Base H WHT WAS CAP L F White Washer Cap H SS 5 C BOLT 1 8 13 x 5 Carriage Bolt 5 5 H 1 2 BLK WASH 1 2 x Black Rubber Washer H 1 2 RED WASH 1 8 x 2 Red Rubber Washer H SS 1 2 F WAS 1 2 USS Flat Washer 5 5 H SS 1 2 LOC WA 1 2 Lock Washer 5 5 H SS 1 2 H NUT 1 2 13 Hex Finish Nut 5 5 H 1 1 2 WHT CAP 750 x 1 1 2 White UV Nut Cap HARDWARE NOTE Use a small dab of anti seize lubricant included on all bolt threads 2 3 4 5 6 7 8 9 o rO rO NDTES DB6WW diving board shown in exploded view for illustration purposes Must be purchased separately Other diving board options available U STAND IM Rev 3 09 BK USTAND BOOK 7 INSTALLATION MANUAL U STAND RESIDENTIAL INGROUND POOL INSTALLATION U Stand Diving Base
8. RESIDENTIAL POOL INSTALLATION INSTRUCTIONS Be sure the concrete deck surrounding the U Stands complies with the minimum dimensions as shown in Figure A on page 6 Read and understand the ANSI NSPI 5 2003 American National Standard for Residential Inground swimming Pools and Table 1 and Table 2 on page 5 before you install the U Stand Diving System The U Stands should be set in accordance with Figure A and Table 3 on page 6 The diving board must be placed on the deep end of the pool on centerline Make sure the U Stands are set 4 into the concrete with ample concrete depth below the stand in accordance with Figure A on page 6 Do not install the U Stand Diving System if the deck does not meet the minimum requirements When finishing the deck surface maintain a level deck where the U Stands project out of the deck surface Both U Stands must be leveled left to right and to each other when installing This will allow the diving board to sit level left to right and have a slight upward pitch at the toe end once the rubber fulcrum pad is in place Allow the cement to fully cure before bolting the diving board to the U Stands When mounting diving board to a newly installed stand with a permanently fixed fulcrum the correct measurement between the mounting holes and the fulcrum must be maintained so as not to void the warranty See Figure A and Table 3 on page 6 The rubber fulcrum pad MUST be used so as not to void the Inter Fab warranty
9. and Hands Up DIVING TIPS Even the safest equipment must be used properly Inter Fab promotes safe diving by offering these tips on the proper use of your diving board always dive into water that meets depth requirements with arms extended be aware of the bottom and the walls of the pool avoid collisions with pool toys and floats and instruct your pool users to always steer up When you begin your dive you must get ready to steer up As you enter the water your arms must be extended over your head hands flat aiming up Hold your head and arch your back Hold Diving Form Steer up for a safe dive U STAND IM Rev 3 09 BK USTAND BOOK 2 SAFETY FIRST A pool is the safest place to swim and a diving board installed in compliance with manufacturers instructions and the ANSI NSPI 5 2003 standards for residential inground swimming pools and the ANSI NSPI 1 2003 standards for public inground swimming pools is the safest place to dive from To ensure that you are able to safely enjoy your diving board for many years it is critical that you follow the following instructions 1 10 TT 18 13 14 DO Know the shape and depth of the pool before you dive Make sure that all family members and guests are familiar with these instructions before they use your pool and diving board Make sure that the diving board has been installed in compliance with the Assembly and Installation Instructions an
10. are not covered within the scope of this standard Class D pools are operated for special purposes including but not limited to wave action pools activity pools leisure rivers vor tex pools and sand bottom pools Class E pools Class E pools are pools used for physical therapy and are above 86 F 30 C and are not covered within the scope of this standard Class F pools Class F pools are wading pools and are covered within the scope of this standard as set forth in 6 9 and 8 4 2 and as noted in other sections of the standard 4 Code compliance 4 1 Codes Pools covered by this standard shall be constructed and operated to comply with all local state and federal codes governing safety and envi ronmental regulations 5 General design 5 1 Plans and permits Prior to construction re habilitation or alteration of a permanently installed public swimming pool plans and specifications shall be submitted to the authority state or local for re view approval and issuance of a permit to construct or rehabilitate as required by the authority having jurisdiction 5 2 Materials Swimming pools and all appurte nances thereto shall be constructed of materials that are nontoxic to humans and the environment that are generally or commonly regarded to be impervious and enduring that will withstand the design stresses and that will provide a watertight structure with a smooth and easily cleaned surface without cracks or jo
11. does not include ordinary maintenance Only those items that are renovated shall adhere to this standard 2 Normative references The following standards contain provisions that through reference in this text constitute provisions of this American National Standard At the time of pub lication the editions indicated were valid All stan dards are subject to revision and parties to agree ments based on this American National Standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below U STAND IM Rev 3 09 BK USTAND BOOK 17 ANSI ASME 112 19 8 1987 1996 Suction fittings for swimming and wading pools spas hot tubs and whirlpool bathtub appliances ANSI ICC A117 1 2003 Standard on accessible and useable buildings and facilities 2 ANSI NEMA MG1I 1998 Motors and generators 2 ANSI NSF 14 2003 Plastics piping system compo nents and related materials ANSI NSF 50 2001 Circulation system compo nents and related materials for swimming pools spas hot tubs ANSI Z21 56 2001 CSA 4 7 2001 Gas fired pool 6 heaters ACI 302 1R 96 1996 Guide for concrete floor and slab construction Americans with Disabilities Act ADA Accessibility guidelines for buildings and facilities recreation facilities ASME A112 1 2 2002 Air gaps in plumbing sys tems i ASTM 1346 91 2003 Standard performance specification for safety covers and
12. labeling require American National Standards Institute ANSI 25 West 43 Street New York NY 10036 NY 212 642 4900 www ansi org gt ANSI previously listed National Electrical Manufacturers Association NEMA 1300 N 17 Street Suite 1847 Rosslyn VA 22209 703 841 3200 www nema org NSF International 789 N Dixboro Rd Ann Arbor MI 48113 734 769 8010 www nsf org 5 NSF previously listed 5 ANSI previously listed 7 American Concrete Institute 38800 Country Club Drive Farmington Hills MI 48331 248 848 3800 www aci int org U S Architectural and Transportation Barriers Compliance Board 1331 F Street NW Suite 1000 Washington DC 20004 202 272 0080 www access board gov American Society of Mechanical Engineers ASME 3 Park Avenue 20 Floor New York NY 10016 212 591 8562 www asme org INSTALLATION MANUAL U STAND SUPPORT INFORMATION 1 7 Extracted from ANSI NSPI 1 2003 American National Standard for Public Swimming Pools ments for all covers for swimming pools spas and hot tubs ASTM F2208 02 Standard specification for pool alarms ANSI NFPA 54 2002 National fuel gas code 70 2002 National electric code UL 1995 1999 Standard for heating and cooling equipment UL 1261 2001 Standard for electric water heaters for pools and tubs 3 Definitions Public swimming pools are classified as follows for purposes of re
13. of pools except that consideration shall be given to shape from the standpoint of circulation of the swimming pool water and safety to the user 5 3 Walls requirements 5 3 1 Walls in the shallow area and deep area of the pool shall not slope greater than 11 1 5 slope POINT B WATER LEVEL TYPICAL MINIMUM CROSS SECTION ratio to a transition point The transition point shall not be less than 2 feet and 9 inches 83 8 cm below the waterline See figure 1 5 3 2 As shown in figure 2 at the depths of a and b the walls are permitted to Join the floor TOP OF WALL WATER LINE PLUMB WALL SECTION 2 9 Minimum 41 MAX REFERENCE DIAGRAM NOT TO SCALE Figure 1 Maximum allowable wall slope TYPICAL GUNITE CONCRETE CONSTRUCTION POOLS WITH 11 WALLS eceesceseee TYPICAL VINYL LINER POOL CONSTRUCTION REFERENCE DIAGRAM NOT TO SCALE Figure 2 Typical pool design configurations U STAND IM Rev 3 09 BK USTAND BOOK INSTALLATION MANUAL U STAND SUPPORT INFORMATION ARTICLE 5 POOL DIMENSIONS AND TOLERANCES Extracted from ANSI NSPI 2003 American National Standard for Residential Inground Swimming Pools 5 3 3 The walls of Type I pool when defining the 5 4 Maximum allowable wall slope minimum diving water envelope shall be plumb or outside of Type 1 water geometry See figure 3 ta 5 4 1 Maximum allowable wall slope shall not ble 1 slope greater than 11
14. 5 sq ft per user 20 sq ft per user 300 sq ft See 7 1 6 through 7 1 6 1 1 35 m per user 1 8 m per user 27 m Pools with deck area at least equal to 12 sq ft per user 15 sq ft per user 300 sq ft water surface area 1 08 m per user 1 35 m per user 27 m Pools with deck area at least twice the 8 sq ft per user 10 sq ft per user 300 sq ft water surface area 0 72 m per user 0 9 m per user 27 6 7 Rest ledges Rest ledges along the pool walls 7 1 1 1 In the absence of specific local are permitted They must be not less than 4 feet 122 cm below the water surface If a ledge is provided it shall be at least 4 inches 10 cm wide and no more than 8 inches 20 cm wide 6 8 Maximum user load The maximum user load of Class B or Class C pools shall be in accordance with table 3 6 9 Wading pools A wading pool shall be a sepa rate pool with an independent circulation system and physically separated from the main pool as described in 6 9 1 through 6 9 4 6 9 1 Areas where the water depth at the edge of the pool exceeds 9 inches 23 cm shall be consid ered non entry areas and must be protected by natural or artificial barriers 6 9 2 Floors of wading pools shall be uniform and sloped to drain with a maximum slope of 1 foot in 12 feet 30 cm in 360 cm 6 9 3 The maximum water depth shall be 18 inches 46 cm 6 9 4 The maximum distance from the top of the deck to the water line shall not e
15. 6 6 25 36 25 30 GUNITE CONSTRUC 049 or DBU18 TION WITH LESS 049 or DBU18 Not recommended Call customer service for more information NOT ALLOWED THAN A 3 RADIUS TO DBU12049 32 50 18 20 THE POOL FLOOR 049 or DBU18 26 50 24 26 DUE TO THE VARYING 09 09 09 92 92 92 20 50 30 30 049 or DBU18 049 or DBU18 14 50 36 40 SIZES OF OTHER NOT ALLOWED POOLS TYPICALLY NOT ALLOWED VINYL LINER CON DBU24 61 5 24 STRUCTION PLEASE DBU24 61 5 30 CONTACT CUSTOMER DBU24 61 5 36 SERVICE FOR PROPER NOT ALLOWED NOT ALLOWED PLACEMENT NOT ALLOWED 1 800 737 5386 NOT ALLOWED IMPORTANT The distance for setting the front jig bolt S from the water s edge is valid only if the minimum water depth is maintained at the tip of the board noted as point A in ANSI NSPI 5 2003 American National Standard for Residential Inground Swimming Pools If minimum water depth is not maintained the distance S must be adjusted accordingly WA dimension is valid only in conjunction with the minimum depth at point A for type pool in accordance with ANSI NSPI 5 2003 American National Standard for Residential Inground Swimming Pools U STANDIM Rev 3 09 BK USTAND BOOK 6 INSTALLATION MANUAL U STAND RESIDENTIAL INGROUND POOL
16. A minimum 4 feet 122 cm deck width shall be provided on the sides and rear of any diving equipment A deck clearance of 3 feet 91 cm shall be provided around all other deck equip ment 7 1 6 The minimum slope of the deck s shall be 1 8 inch per 1 foot 3 2 mm per 304 8 mm for textured hand finished concrete decks 1 4 inch per 1 foot 6 4 mm per 304 8 mm for exposed aggregate INSTALLATION MANUAL U STAND SUPPORT INFORMATION antictes 1 7 Extracted from ANSI NSPI 1 2003 American National Standard for Public Swimming Pools concrete decks 1 2 inch per 1 foot 12 7 mm per 304 8 mm for indoor outdoor carpeting decks and 3 8 inch per foot 9 5 mm per 304 8 mm for brick and heavy textures finishes unless an alternate drain age method is provided that prevents the accumula tion of pooling of water See table 4 7 1 6 1 Decks shall be sloped so that standing water shall be no deeper than 1 8 inch 3 2 mm 20 minutes after the cessation of the addition of water to the deck NOTE Two stacked U S quarters can be used to measure the depth Water should not cover the quarters 7 1 7 The maximum slope of all decks other than wood decks shall be 1 2 inch per foot 12 7 mm per 304 8 mm except for ramps 7 1 7 1 The maximum slope for wood decks shall be 1 8 inch per 1 foot 3 2 mm per 304 8 mm 7 1 7 2 Gaps shall be required between deck boards in wood decks and shall be consistent with approved engineering met
17. ALE Figure 3 Minimum diving water envelope To obtain complete copies of the ANSI NSPI 1 2003 Standard for Public Swimming Pools contact The Association of Pool amp Spa Professionals APSP 2111 Eisenhower Ave Alexandria VA 22314 703 838 0083 or visit www apsp org U STAND IM Rev 3 09 BK USTAND BOOK 25 INSTALLATION MANUAL U STAND LIMITED WARRANTY Inter Fab Inc will repair or replace at its option any product manufactured by Inter Fab Inc that fails during the applicable warranty period because of a manufacturing or material defect provided that the defect is not the result of improper installation improper use or care negligence alterations or modifications to the product or natural accidents acts of God The applicable warranty period for products manufactured by Inter Fab Inc is three 3 years from the date of retail purchase except as specified below Echoes of Nature products are individually handcrafted and painted by skilled artisans and as a result dimensional differences and color variations are normal and are not a basis for warranty coverage The warranty period for pumps sold with the Echoes of Nature products is three 3 years from the date of retail purchase Water Sports sports equipment warranty periods are as follows Volleyball Poles Basketball Poles Basketball Rim and Basketball Backboard are one 1 year from date of retail purchase Volleyball Volleyb
18. MAX DIVING MAX HEIGHT CROSS SECTIONAL MIN HEAD L LENGTH OATPONTA D BONA CROSS SECTIONAL DIMENSIONS AT POINT B ROOM m DIVING pgL F G H J K L M N SURFACES 0 DIVING EQUIPMENT PROHIBITED 608 6 JB 20 eg 50 40 725 78 6 0 3 9 215 12 8DE EJB eg 3140 4 7 25 76 68 3 9 215 12 10 DB 8 JB _ 26 2 9 14475 445 755 8 0 87 3 115 1 25 13 40 DE 8 JB 30 2 9 5 105 3 10 78 8 6 8 3 57 27 13 v 1208 88 40 eg 6 2 3115 7 95 9 0 Bes 5 9 27 14 Min length between points CD may vary based upon water depth at point D and the slope between points C amp D ABBREVIATIONS DBL Diving Board Length DB Diving Board JB Jump Board HOW Height Over Water U STAND IM Rev 3 09 BK USTAND BOOK 5 INSTALLATION MANUAL U STAND RESIDENTIAL INGROUND POOL INSTALLATION NOTE READ THESE INSTRUCTIONS IN THEIR ENTIRETY BEFORE ATTEMPTING THE INSTALLATION DECK END WATER END a BOLT HOLES FIG U STAND RESIDENTIAL PLACEMENT SPECIFICATIONS DIVING BOARD B 4 INTO FULCRUM PAD idi Usu SEE TABLE 3 REBAR DIVING BOARD ia FULCRUM PAD U FRAME HOW FINISH GRADE EN i 3 REBAR cat N CONCRETE SLAB C DECK LENGTH 8 MIN
19. OL INSTALLATION MINIMUM DIVING WATER ENVELOPE m NOTE DRAWINGS ARE NOT TO SCALE F SECTION c em CROSS SECTION AT POINTA x 2 0 R WATERLINE DIVING EQUIPMENT REFERENCE DIAGRAM NOT TO SCALE MINIMUM WATER SURFACE SHAPE TIP OF BOARD ABOVE POINT A MINIMUM WIDTH LENGTH AND DEPTH DIMENSIONS FOR WATER ENVELOPE NC START FROM POINT A DIVING EQUIPMENT D E WATERLINE CROSS SECTION AT POINT B Mm ALLOWA PC _ E pode END WALL en WA EC 2 8 R MAX TABLE 1 MINIMUM WATER ENVELOPE ANSI NSPI 5 2003 CROSS SECTION AT POINT C MINIMUM DEPTHS MINIMUM WIDTHS MINIMUM LENGTHS AT POINT AT POINT BETWEEN POINTS TYPE A D A C D wa 3 AB BC co DE WE MOm 0 DIVING EGUIPMENT PROHIBITED 6 0 7 6 5 0 2 9 10 0 12 0 10 0 8 0 te 170 7 5 6 0 28 9 6 0 7 6 5 0 2 9 12 0 15 0 12 0 8 0 T amp 7 0 7 6 varies 6 0 28 9 an 610 8 0 5 0 2 9 1 15 0 12 0 8 0 2 0 z amp 8 0 6 0 31 3 MeL UE _ 7 8 8 6 5 0 2 9 15 0 18 0 15 0 9 0 2 6 8 0 10 6 6 0 38 9 v 9 0 5 0 2 9 15 0 18 0 15 0 9 0 3 0 9 0 12 0 VAREES 6 0 36 9 TABLE 2 INTER FAB RESIDENTIAL POOL MINIMUM SPECIFICATIONS
20. R WATER e Deck Level Board to Pool Side 2 3 Meter e 1 Meter Board to Pool Side 26 e 3 Meter Board to Pool Side With multiple board installations minimum pool widths must be g 14 3 4 Meter e 1 Meter or Deck Level Board to 3 Meter Board 30 e 1 Meter or Deck Level Board to Another 1 Meter 1 Meter or Deck Level Board e 3 Meter to Another 3 Meter Board 3 Meter TABLE 9 COMMERCIAL PLACEMENT CHART ADDITIONALLY REFER ANSI NSPI 1 2003 American National Standard for Public Swimming Pools NOMINAL DISTANCE FROM DISTANCE MAX HEIGHT U STANDARDS BOARD WATER S EDGE FROM END MIN OF BOARD PART LENGTH TO FORWARD OF BOARD OVERHANG ABOVE U STAND TO FORWARD L WATER S U STAND HOW 08018065 or DBU24065 10 VI SA eTa 30 26 9 10 HEIGHT OF U STAND 1e 1210 52 sI 0 018065 er DBU24065 10 Cu 36 30 ish A0 IMPORTANT THESE DIMENSIONS ARE ACCURATE ONLY FOR VERTICAL POOL WALLS TYPICALLY GUNITE CONSTRUCTION PLEASE CONTACT CUSTOMER SERVICE FOR PROPER PLACEMENT 1 800 737 5386 IMPORTANT The distance for setting the front jig bolt 5 from the water s edge is valid only if the minimum water depth is maintained at the tip of the board noted as point A in ANSI NSPI 1 2003 American National Standard for Public Inground Swimming Pools If minimum water depth is not maintained the distance 5 must be adjusted accordingly L4 dimension is valid only in conjunction with the m
21. The Diving Board must be installed according the below board leveling instructions LEVEL The top surface of the diving board from the deck end to the tip end shall be level or have an upward slope of 5 8 bs pe per foot maximum Elevation difference shall not exceed from the deck end to the tip of the board There shall w mna E be no downward slope towards the water The slope shall DECK END eS 6 oe using a level as shown in the graphic to the ONLY ONE PERSON ON THE DIVING BOARD AT A TIME WITH A MAXIMUM WEIGHT OF 250 LBS U STAND IM Rev 3 09 BK USTAND BOOK 8 INSTALLATION MANUAL U STAND SUPPORT INFORMATION ARTICLE 5 POOL DIMENSIONS AND TOLERANCES Extracted from ANSI NSPI 2003 American National Standard for Residential Inground Swimming Pools 5 Pool dimensions and tolerances 5 1 General requirements Design dimensions shall comply with specifications in this standard The pool shall be constructed to these design dimensions within the tolerances listed in 5 1 1 5 1 1 Construction tolerances There shall be construction tolerances allowed on dimensional de signs The overall length width and depth shall be limited to a tolerance of plus or minus 3 inches 7 6 cm All other dimensions shall be limited to a toler ance of plus or minus 2 inches 5 1 cm unless otherwise specified 5 2 Perimeter shape No limits are specified for shape
22. U STYLE STAND DIVING SYSTEM Assembly amp Installation Instructions EL ALVERNON WAY TUCSON A 7040 800 737 5386 FAX 520 inter Fab com U STAND IM Rev 3 09 BK USTAND BOOK U STYLE STAND DIVING SYSTEM OWNER S MANUAL e TUCSON A 5386 FAX 520 U STAND IM Rev 3 09 BK USTAND BOOK For Technical Support or Assistance Contact Customer Service at INTER FAB INC 3050 S ALVERNON WAY TUCSON AZ 85713 800 737 5386 or visit www inter fab com To obtain complete copies of the most current ANSI NSPI 2003 Standards for Inground Pools or to obtain copies of the Plan Your Dive Steer Up or The Sensible Way to Enjoy Your Inground owimming Pool contact The Association of Pool amp Spa Professionals APSP 2111 Eisenhower Ave Alexandria VA 22314 703 838 0083 or visit www theapsp org U STAND IM Rev 3 09 BK USTAND BOOK INSTALLATION MANUAL U STAND TABLE OF CONTENTS IPSE ear e 3 Important Notices to the Installer 4 Board to Base Compatibility Chart 4 RESIDENTIAL Minimum Diving Water Envelope Information 5 U Stand Base Placement Residential 6 U Stand Specifications Residential 6 Exploded View
23. all Net Basketball Basketball Net and pumps are warranted for ninety 90 days from date of retail purchase Splash Rock Edgewater T7 Edgewater and Lighted Edgewater features warranty period is one 1 year from date of retail purchase Zoomerang slide products warranty period is one 1 year from the date of retail purchase Build Your Own Slide BYOS warranty period is one 1 year from the date of retail purchase City 2 Slide and City Base products warranty period are one 1 year from the date of retail purchase Unless expressly stated otherwise all products manufactured by Inter Fab are for residential installation single family residence inground pool use only Inter Fab Inc expressly disclaims any and all warranties and liability arising from the installation or use of its residential products for any non residential use such as semipublic public or commercial applications Products expressly manufactured for commercial installation and use will be subject to this limited warranty This limited warranty is in lieu of all other warranties whether express or implied Inter Fab Inc disclaims any warranty of merchantability or fitness for a particular use and noninfringement in relation to any of its products and Inter Fab Inc is not liable for consequential incidental or specific damages This warranty is limited to the repair or replacement of the manufacturing or material defect or refund of the orig
24. atures prohibited in the water envelope U STAND IM Rev 3 09 BK USTAND BOOK 13 INSTALLATION MANUAL U STAND SUPPORT INFORMATION ARTICLE 5 POOL DIMENSIONS AND TOLERANCES Extracted from ANSI NSPI 2003 American National Standard for Residential Inground Swimming Pools 5 10 1 The maximum height of the stationary diving platform or diving rock above the waterline shall be as follows Pool Type I 42 inches 106 7 cm Pool Type II 42 inches 106 7 cm Pool Type III 50 inches 127 0 cm Pool Type IV 60 inches 152 4 cm or Pool Type V 69 inches 175 3 cm 5 10 2 Stationary diving platform s and div ing rock s shall not be permitted on Pool Type O 5 10 3 The diving equipment manufacturer shall specify minimum headroom above water 5 11 Swimming pool slides 5 11 1 Slides where installed shall be in stalled in accordance with manufacturer s specifica tions NOTE For consumer safety information warn ings and education programs see appendices D E and F To obtain complete copies of the ANSI NSPI 5 2003 Standard for Residential Inground Pools contact The Association of Pool amp Spa Professionals APSP 2111 Eisenhower Ave Alexandria VA 22314 703 838 0083 or visit www theapsp org U STAND IM Rev 3 09 BK USTAND BOOK 14 INSTALLATION MANUAL U STAND PUBLIC POOL INSTALLATION NOTE READ THESE INSTRUCTIONS IN THEIR ENTIRETY BEFORE ATTEMPTING THE INSTALLATION
25. cessibility guidelines for buildings and facilities recreation facilities ADAAG 6 Dimensional design 6 1 Perimeter shape This standard is not in tended to regulate the perimeter shape of swimming pools It is the designer s responsibility to take into account the effect a given shape will have on the safety of the occupants and required circulation to ensure sanitation All other dimensions unless oth erwise specified should allow a 2 inches 51 mm tolerance 6 1 1 There shall be no protrusions exten sions means of entanglement or other obstructions in the swimming pool areas that may cause the en trapment or injury of the user 6 2 Allowable construction tolerances These construction tolerances are not applicable to Class A pools 6 2 1 Finished pool dimensions shall be held within the following construction tolerances as shown in table 1 6 3 Floor slope Floor slopes shall be in compli ance with 6 3 1 through 6 3 5 except the require ments by the ADA Accessibility guidelines ADAAG 6 3 1 All pool floors shall be sloped to the drain 6 3 2 The slope of the floor in the shallow area shall not exceed 1 foot in 10 feet in Class C pools or 1 foot in 12 feet in Class B pools in any direction to the point of the first slope change if a slope change exists 6 3 3 The point of the first slope change shall be defined as the point at which the floor slope ex ceeds 1 foot in 10 feet in Class C pools or 1 f
26. d with the 2003 ANSI NSPI Standards for In ground Pools This includes the shape and depth of the pool as well as the height of the diving board Enter feet first the first time Plan your path to be sure you avoid any other swimmers or objects in or under the water such as floats tires toys etc Keep your head up arms up and fully extended and steer up with your hands Practice carefully before you dive headfirst Become familiar with the diving board and its spring before diving headfirst Dive straight ahead not to the side of the board or pool Dive from the diving board only Make sure that children and non swimmers are supervised at all times Always remember that when you dive you must steer up Inspect your diving board base and stand on a regular basis at least twice a year and keep them in proper repair Contact your dealer installer or Inter Fab 800 737 5386 with any questions or concerns about the safe use of your diving board DON T 1 2 41 18 Don t drink and dive Dont install this or any diving board on an above ground pool or dive into an above ground pool from any surface Don t dive into a pool from anyplace not specif ically designated for diving Never dive into the shallow portion of any pool Don t dive across the width of the pool or to the sides of the pool Don t Run and dive Don t engage in horseplay in or around the diving board or pool Dont use you
27. ded for rinsing down the entire deck and shall be in accor dance with the authority having jurisdiction 7 1 17 Water powered devices such as water powered lifts shall have a dedicated hose bib water source 7 2 Deck equipment Deck equipment including diving facilities and starting blocks shall comply with 7 2 1 through 7 4 as applicable Table 4 Typical minimum drainage slope Surface Typical minimum drainage slope inch per foot Textured hand finished concrete 1 8 in 3 2 mm Exposed aggregate 1 4 in 6 4 mm Carpet 1 2 in 12 7 mm Brick and heavy textures finished 3 8 1n 9 5 mm U STAND IM Rev 3 09 BK USTAND BOOK e3 INSTALLATION MANUAL U STAND SUPPORT INFORMATION antictes 1 7 Extracted from ANSI NSPI 1 2003 American National Standard for Public Swimming Pools 7 2 1 A minimum 4 feet 122 cm deck width shall be provided on the sides and rear of any diving equipment 7 2 2 Starting blocks Starting blocks are in tended for competitive swimming and shall conform to Federation Internationale de Natation FINA U S A Swimming National Collegiate Athletic As sociation NCAA or National Federation of State High Schools Associations NFSHSA 7 2 3 There shall be a completely unobstructed distance of 14 feet 427 cm above the tip of the div ing board or as specified by the diving equipment manufacturer or the authority having jurisdiction
28. e appendix H Glossary Walls may intersect with the floor at an an 6 5 1 When diving equipment is installed it gle or a transition profile shall conform to the specifications set forth in 7 2 1 through 7 2 5 6 Equipment shall be located in the At water depths between 3 feet to 5 feet 91 diving area of the pool on the appropriate cm to 152 cm the maximum radius shall be 2 ANSI NSPI pool type or other water envelopes feet 3 inches 69 cm specified by the diving equipment manufacturer in accordance with the manufacturer s installation in At water depths of 3 feet 91 cm or less a structions and the minimum dimensions as shown in transitional radius shall not exceed 6 inches figure 1 Competitive diving equipment shall not be 15 cm and shall be tangent to the wall and installed on Class B and Class C pools may be tangent to or intersecting the floor 6 6 manufacturer of the diving equipment At water depths greater than 3 feet 91 cm shall specify minimum water envelopes for its prod transitional radius shall be tangent to the wall ucts They may refer to the water envelope type of at a point no less than 2 feet and 6 inches 76 their choice by dimensionally relating their products cm below the water surface and may progres to Point A on that water envelope Point A as sively increase from 6 inches 5 cm to a value shown in figure 1 is designated as the point of origin capable of being tan
29. ference and application of this stan dard Class A pools Class A pools are pools intended for use for accredited competitive aquatic events such as Federation Internationale de Natation FINA U S A Swimming U S Diving National Collegiate Athletic Association NCAA National Federation of State High Schools Associations NFSHSA etc The pool may also be used for recreation Class A pools are covered unless otherwise noted in the body of the standard Class B pools Class B pools are pools intended for public recreational swimming not otherwise classi fied Class B pools are covered within the scope of this standard Class C pools Class C pools are pools intended for use for apartments condominiums property owners associations multi family owned pools etc and are 9 ASTM International 100 Barr Harbor Drive W Conshohocken PA 19428 610 832 9585 www astm org ASTM previously listed 12 National Fire Protection Association NFPA 1 Batterymarch Park Quincy MA 02269 617 770 3000 www nfpa org NFPA previously listed Underwriters Laboratories UL 333 Pfingsten Road Northbrook IL 60062 847 272 8800 www ul com 5 UL previously listed U STAND IM Rev 3 09 BK USTAND BOOK 18 covered within the scope of this standard Pools oper ated solely for and in conjunction with lodgings such as hotels and motels are also covered within the scope of this standard Class D pools Class D pools
30. from plumb SECTION S et SYMMETRY B xL 2 0 R REFERENCE DIAGRAM NOT TO SCALE MINIMUN WATER SURFACE SHAPE LR MINIMUM WIDTH LENGTH AND DEPTH DIMENSIONS FOR WATER ENVELOPE START FROM POINT A D E WATERLINE TM gr SEE FIGURE 3 FOR 29 q 2 9 sHALLOW END DETAIL ALLOWABLE W DEEP END WALL BC E SHALLOW END WALL WA PR WATERLINE WATERLINE i i 1 SYM 1 i i CROSS SECTION AT POINT A CROSS SECTION AT POINT B WATERLINE WATERLINE SYM i 6 R 2 3 R MAX SYM CROSS SECTION AT POINT C CROSS SECTION AT POINT D REFERENCE DIAGRAM NOT TO SCALE Figure 3 Minimum water envelope U STAND IM Rev 3 09 BK USTAND BOOK 10 INSTALLATION MANUAL U STAND SUPPORT INFORMATION ARTICLE 5 POOL DIMENSIONS AND TOLERANCES Extracted from ANSI NSPI 2003 American National Standard for Residential Inground Swimming Pools Table 1 Minimum water envelope Minimum depths Pool at point Minimum widths at point type A C D A B C D WA AB O _ Manufactured diving equipment is prohibited I 6 0 7 6 5 0 127 9 10 0 12 0 0 0 18 0 1 6 7 O 7 6 Varies 60 28 9 II 6 0 7 6 5 0 2 9 112 0 15 0 12 0 8 0 1 6 7 0 e Varies 6 0 28 9 6 10 8 0 5 0 2 9 12 0 115 0 12 0 8 0 2 0 7 6 9 0 Varies 6 0 31 3 7 8 8 6 5 0 2 9 115 0 118 0 15 0 9 0 pe 8 0 10 6 Varies 6 0 33 9 V 8 6 9 0
31. from the shallow end except as specified in 6 3 5 6 3 The slope of the floor from the point of the first slope change toward the deep end shall not exceed 1 foot in 3 feet 30 cm 91 cm SHALLOW END WATERLINE E STEEPEST ALLOWABLE MAX SLOPE SLOPE ZR 4 11 MAX MORTO SCALE AM TYPE PLUMB FC 6 0 MIN Figure 5 Shallow end depths INSTALLATION MANUAL U STAND SUPPORT INFORMATION ARTICLE 5 POOL DIMENSIONS AND TOLERANCES Extracted from ANSI NSPI 2003 American National Standard for Residential Inground Swimming Pools 5 7 Shallow end water depths Water depth in the shallow area shall be a minimum of 2 feet 9 inches 83 8 cm except for those locations specified in 6 3 Shallow End Detail for Beach and Sloping Entries The water depth at the shallowest point shall not exceed four feet 121 9 cm as shown in figure 5 5 8 Manufactured diving equipment for in ground swimming pools diving board stand com bination or manufactured platform NOTE For consumer safety information warnings and education programs See appendices D E and F 5 8 1 When manufactured diving equipment is installed it shall conform to the specifications set forth in 5 8 through 5 9 and shall be located in the deep area of the pool so as to provide the minimum dimensions as shown in 5 9 5 8 1 1 Manufactured diving equipment shall not be installed on Type 0 pools 5 8 2 Diving equipment Diving equi
32. gent to or intersecting the on the water surface for the water envelope dimen floor sion 6 4 Water depths Water depths for swimming 6 6 1 Point A is a point located on the water areas shall be a minimum depth of 3 feet 91 cm surface of pool water envelopes unless the authority having jurisdiction specifies oth erwise 6 6 2 Point A is a construction location nearest the deep end wall where the minimum water depth D 6 4 1 Class A pools shall be designed and con is satisfied structed to provide the dimensions specified by Fed eration Internationale de Natation FINA U S A 6 6 3 Point as shown in figure 1 and table 2 Swimming U S Diving or other appropriate sanc shall be the referenced point of origin for all dimen sions defining a minimum water envelope Pt A Water Line Pt C Pt D E cm 11 Max slope 11 Max slope 1 in 12 Max slope Class B 1 in 10 Max slope Class C 3 Max slope Figure 1 Construction dimensions for water envelopes for Class B and Class C pools U STAND IM Rev 3 09 BK USTAND BOOK 20 INSTALLATION MANUAL U STAND SUPPORT INFORMATION 1 7 Extracted from ANSI NSPI 1 2003 American National Standard for Public Swimming Pools TOP OF WALL WATER LINE Use for all pools except Class A pool walls where racing lanes terminate PLUMB WALL SECTION E gt
33. h slip resisting tread All diving stands higher than 21 inches 53 cm measured from the deck to the top butt end of the board shall be provided with stairs and or a ladder Step treads shall be self draining 7 2 5 6 Diving equipment meter high 39 inches or greater shall be provided with a top guard rail which shall be at least 30 inches 76 cm above the diving board and extend to the edge of the pool wall and to the deck surface 7 3 Swimming pool slides Swimming pool slides when installed shall comply with the require ments of the U S Consumer Product Safety Commis sion CPSC as published in the Code of Federal Regulations 16 CFR Part 1207 The manufacturer shall provide installation and use instructions with each slide Each slide shall be installed in accordance with the manufacturer s instructions 7 4 Play water activity equipment When in stalled play water activity equipment shall be in stalled in accordance with manufacturer s instruc tions INSTALLATION MANUAL U STAND SUPPORT INFORMATION aanticte 23 1 5 Extracted from ANSI NSPI 1 2003 American National Standard for Public Swimming Pools 23 1 5 If the pool is designed for use with diving equipment the entries and exits pool stairs ladders underwater benches special features and other accessories shall be located outside the mini mum diving water envelope as shown in figure 3 UNDERWATER SEAT OR BENCH REFERENCE DIAGRAM MOT TO SC
34. he pool on centerline Make sure the U Stands are set 4 into the concrete with ample concrete depth below the stand in accordance with Figure on page 15 Do not install the U Stand Diving System if the deck does not meet the minimum requirements When finishing the deck surface maintain a level deck where the U Stands project out of the deck surface Both U Stands must be leveled left to right and to each other when installing This will allow the diving board to sit level left to right and have a slight upward pitch at the toe end once th rubber fulcrum pad is in place Allow the cement to fully cure before bolting the diving board to the U Stands When mounting diving board to a newly installed stand with a permanently fixed fulcrum the correct measurement between the mounting holes and the fulcrum must be maintained so as not to void the warranty See Figure C and Table 8 and 9 on page 15 The rubber fulcrum pad MUST be used so as not to void the Inter Fab warranty A rubber mounting pad MUST be installed between the bottom of the diving board and the heel end U Stand as not to void the Inter Fab warranty The Diving Board must be installed according the below board leveling instructions LEVEL The top surface of the diving board from the deck end to um the tip end shall be level or have an upward slope of 5 8 TOER ss per foot maximum Elevation difference shall not exceed 6 from the deck end to
35. hods with respect to the type of wood used and shall not cause a tripping hazard 7 1 8 The maximum open gap between pool decks and adjoining decks or walkways including joint material shall be 3 4 inch 19 1 mm The dif ference in vertical elevation between the pool deck and the adjoining sidewalk shall be 1 4 inch 6 4 mm unless it conforms to 7 1 4 7 1 9 Construction joints where the pool cop ing meets the concrete deck s shall be watertight 7 1 10 Construction joints where the pool coping meets the concrete deck s shall be installed to protect the coping and its mortar bed from damage as a result of the anticipated movement of adjoining deck s 7 1 11 Control joints in deck s shall be pro vided to minimize visible cracks outside the control joints due to imposed stresses and or movement of the slab 7 1 12 Areas where decks join existing con crete work shall be protected by an expansion joint to protect the pool from the pressures of relative move ments 7 1 13 The edges of all decks shall be radi used tapered or otherwise designed to eliminate sharp corners 7 1 14 Pressure tests A pressure test shall be maintained throughout the deck pour and in accor dance with 8 4 7 1 15 Valves installed in or under any deck s shall have access provided for operation service and maintenance Access covers shall be provided 7 1 16 Hose bib s with a cross connection control to prevent backflow shall be provi
36. inal purchase price whichever is less at the sole option of Inter Fab Inc and expressly does not cover any labor or reinstallation expenses related to the replacement of any and all Inter Fab products This limited warranty shall be the sole and exclusive remedy of irrespective of whether the claims are made in contract tort warranty law equity or by statue This warranty is to the original purchaser of the product only Inter Fab s limited warranty is neither transferable nor portable from consumer to consumer The effective coverage date begins at the date of retail purchase Product owner or representative must notify Inter Fab Inc or its wholesale agent in writing giving a full description of the nature of the product defect or failure along with proof of purchase serial number s of the product and photos within thirty 3O days of the expiration of the applicable warranty period Inter Fab Inc reserves the right to physically inspect damaged or defective products or components to determine the cause of the damage or defect prior to authorizing repair or replacement of its products nben fan 3050 S Aluernon Way Tucson AZ 85713 520 790 7040 e 800 737 5386 e Fax 520 790 7127 inter fab com U STAND IM Rev 3 09 BK USTAND BOOK 26
37. inimum depth at point A for type pool in accordance with ANSI NSPI 1 2003 American National Standard for Public Inground Swimming Pools U STAND IM Rev 3 09 BK USTAND BOOK 15 INSTALLATION MANUAL U STAND PUBLIC POOL INSTALLATION FIG D PUBLIC POOL BOARD MOUNTING DIAGRAM I Diving Board HARDWARE NOTE Use a small dab of anti seize lubricant included on all bolt threads Ree a eter eect TETTE Mt EE EE 5 i 2425252525 qe rd dpt qutt tat tat tata tata ta tata ta itat aaa t aa a 5 COMMERCIAL MOUNTING KIT KEY 1 1 2 X B Carriage Bolt Stainless Steel 2 ea 2 Stainless Steel Top Mounting Plate 1 ea 3 Rubber Mounting Pad 2 ea 4 Bottom Mounting Plate 1 ea NOTE Tighten Hex Nuts 5 Between 20 25 FT LBS 6 DO NOT OVER TIGHTEN 7 1 2 Lock Washer C S Stainless Steel 2 ea 1 2 Hex Nut C S Stainless Steel 2 ea 1 2 White Rubber Bolt Cap 2 ea di U STAND DIVING BASE PUBLIC POOL INSTALLATION INSTRUCTIONS Be sure the concrete deck surrounding the U Stands complies with the minimum dimensions as shown in Figure C on page 15 Head and understand the ANSI NSPI1 2003 American National Standard for Public Swimming Pools and Table 8 and Table 9 on page 15 before you install the U Stand Diving System The U Stands should be set in accordance with Figure C and Table 8 and 9 on page 15 The diving board must be placed on the deep end of t
38. ints excluding structural joints or to which a smooth easily cleaned surface finish is applied or attached 5 2 1 Selection of materials Clean sand or similar material if used in a beach pool environment shall be used only over an impervious surface The INSTALLATION MANUAL U STAND SUPPORT INFORMATION antictes 1 7 Extracted from ANSI NSPI 1 2003 American National Standard for Public Swimming Pools sand area shall be designed and controlled so that the circulation system maintenance safety sanitation and operation of the overall pool are not adversely affected 53 Structural design The structural design shall be in accordance with accepted engineering practices 5 4 Freeze protection In climates subject to freezing temperatures the pool shell and appurte nances piping filter system pump and motor and other components shall be designed and constructed to facilitate protection from damage due to freezing 5 5 Surface condition The surfaces within the pool intended to provide footing for users shall have a slip resisting surface and shall not cause injury to the feet during normal use 5 6 Colors and finishes The colors patterns or finishes of the pool interior shall not obscure objects or surfaces within the pool 5 7 Accessibility for persons with disabilities For Americans with Disabilities Act ADA require ments for accessibility for persons with disabilities into public swimming pools see ADA Ac
39. oot in 12 feet in Class B pools Table 1 Construction tolerances Design requirements Construction tolerance allowed Length overall 3 in 76 mm Width overall 3 in 76 mm Depth deep area including diving area 3 in 76 mm Depth shallow area 2 in 51 mm Step treads amp risers 1 2 in 13 mm Waterline pools with adjustable weir skimmers 1 4 in 6 mm Waterline pools with nonadjustable skimming systems gutters Wall slopes 1 8 in 3 mm 3 degrees All dimensions not otherwise specified in this standard 2 in 51 mm Competitive pools Class A pools All dimensional requirements As governed by sanctioning authority U STAND IM Rev 3 09 BK USTAND BOOK INSTALLATION MANUAL U STAND SUPPORT INFORMATION antictes 1 7 Extracted from ANSI NSPI 1 2003 American National Standard for Public Swimming Pools 6 3 4 The slope of the floor from the point of tioning body See appendix H Glossary for the defi the first slope change to the deep area shall not ex nition of pools Commercial Public Pool Class A ceed foot in 3 feet 65 Diving This standard does not cover diving 6 3 5 Walls Where walls join the floor the requirements for Class A pools This standard covers transitional point or profile shall comply with the diving requirements for Class B and Class C pools following Se
40. pment shall be designed for swimming pool use and shall be installed in accordance with the manufacturer s speci fications 5 8 2 1 Diving equipment installation and use instructions shall be provided by the diving equipment manufacturer and shall specify the mini mum water dimensions required for each diving board and diving stand combination They may refer to the water envelopes type of their choice by dimen sionally relating their products to Point A on the wa ter envelopes as shown in figure 3 and table 1 5 9 1 through 5 9 3 5 8 2 2 Diving equipment shall be per manently labeled and affixed to the diving equipment or jump boards and shall include but not be limited to manufacturer s name and address date of manufacture minimum water envelope required for each diving board and diving stand combination and maximum weight limitations of the user as specified by the board manu facturer U STAND IM Rev 3 09 BK USTAND BOOK 18 5 8 2 3 Diving equipment shall have slip resisting tread surfaces 5 9 Figure 3 contains suggested drawings and dia grams for minimum water envelope for swimming pools designated type I V Individual pool types are shown in figure 3 and table 1 5 9 1 Location of point A Point A shall be defined as a point located on the minimum water en velopes 5 9 1 1 Point A Point A is a construc tion location nearest the deep end wall where the minimum water depth is sa
41. r diving board as a trampoline Dont do a back dive Backyard pools are not built for that type of activity Don t try fancy dives Keep the dives simple Don t dive into or through objects or toys such as inner tubes Don t swim or dive alone Dont use a diving board or stand or base that is rusted or worn out or in poor repair THE U STAND DIVING SYSTEM IS A DIVING BOARD U STAND IM Rev 3 09 BK USTAND BOOK INSTALLATION MANUAL U STAND IMPORTANT NOTICES TO THE INSTALLER The specifications found in this manual represent the minimum water envelope required by Inter fab and by the ANSI NSPI 2003 Standards for Inground Swimming Pools Each of these dimensions must be met or exceeded Installation of a diving board of any type on a pool that does not meet or exceed each of the minimum specifications as provided in this manual including but not limited to the slope requirement is in direct violation of this manufacturer s instructions and the 2003 Standards and can result in serious injury or death A 6 diving board can only be installed on a 12 or 18 U Stand base an 8 diving board can only be installed on a 12 or 18 U Stand base diving board can only be installed on an 18 or 24 U Stand base and a 12 diving board can only be installed on a 24 U Stand base Comply with local government regulations for Inground Swimming Pools if they exceed the ANSI NSPI 2003 Standards Head caref
42. the tip of the board There shall be downward slope towards the water The slope shall DECK END ee sq using a level as shown in the graphic to the U STAND IM Rev 3 09 BK USTAND BOOK 16 INSTALLATION MANUAL U STAND SUPPORT INFORMATION 1 7 Extracted from ANSI NSPI 1 2003 American National Standard for Public Swimming Pools ANSI NSPI 1 2003 Standard for Public Swimming Pools 1 Scope 11 Public swimming pools This standard covers public swimming pools to be used for bathing and operated by an owner licensee or concessionaire regardless of whether a fee is charged for use 1 1 1 Public swimming pools covered by this standard Public swimming pools covered by this standard include Class A pools pools used for com petitive aquatic sports Class B and Class C pools pools intended for public or semi public recreational swimming and Class F pools for wading See article 3 for definitions 12 Variation in design This standard provides specifications for the design equipment operation warning signs installation sanitation new construc tion and renovation of public swimming pools This standard permits variations in equipment materials and design to accommodate special needs and con siderations and advances in technology and to pro vide the required quality strength durability and safety for the intended use 13 Renovation See appendix H Glossary Renovation
43. tional Standard for Residential Inground Swimming Pools ANSI NSPI 5 2003 or on public inground pools that meet or exceed the minimum water envelop dimensions of the ANSI NSPI 1 2003 standard for public pools and in accordance with the included INTER FAB POOL SPECIFICATIONS Installation should conform to local building regulations if they exceed the ANSI NSPI standards In addition to the above standards and referenced specifications these installation instructions provided by Inter Fab Inc must be followed diligently It is also important that any and all warnings provided with the diving board be strictly adhered to and posted in a conspicuous location If not provided or they are misplaced please purchase warning signs from your pool contractor or professional pool supply store and post them in a location that the users of the diving board can clearly see A pool is the safest place to swim and a diving board installed in compliance with manufacturers instructions and the ANSI NSPI 5 2003 standards for residential inground swimming pools and the ANSI NSPI 1 2003 standards for public inground swimming pools is the safest place to dive from To ensure that you are able to safely enjoy your diving board for many years it is critical that you follow the following instructions ONLY ONE PERSON ON THE DIVING BOARD AT ONE TIME MAXIMUM WEIGHT 250 LBS Plan Your Dive PLAN YOUR DIVE STEER UP Back Arched Arms Extended Head
44. tisfied 5 9 1 2 Point A as shown in figure 3 and table 1 shall be the reference point of origin for all dimensions defining the minimum water envelope 5 9 2 Type 0 pool where diving is prohibited shall not be limited in width length or water depth except as specifically provided for in this standard 5 9 3 Location of equipment and pool fea tures in the minimum water envelope If the pool is designed for use with diving equipment steps pool stairs ladders underwater benches special features and other accessory items shall be located outside the minimum water envelope See figure 6 5 9 4 Typical pool design configurations Vinyl liner shotcrete fiberglass and concrete con structions shall conform to but are not limited to the typical pool configurations shown in figure 2 5 10 Stationary diving platform s and diving rock s Stationary diving platform s and diving rock s built on site shall be allowed to be flush with the wall and located in the diving area of the pool Point A shall be in front of the wall at the platform or diving rock centerline NOTE For consumer safety information warning and education programs See appendices D E and F INSTALLATION MANUAL U STAND SUPPORT INFORMATION ARTICLE 5 POOL DIMENSIONS AND TOLERANCES Extracted from ANSI NSPI 2003 American National Standard for Residential Inground Swimming Pools Figure Top view examples of accessory equipment and pad fe
45. ully pages 9 14 and pages 17 25 of this installation manual which contain portions of the ANSI NSPI 5 2003 Standard for Residential Inground Swimming Pools and the ANSI NSPI 1 2008 Standard for Public Swimming Pools NOTE The installation of this diving board and or stand is not complete until you the installer have measured the pool as well as the diving board s height above water and the board s overhang to ensure they meet Inter Fab s minimum water envelope specifications and the ANSI NSPI 2003 Standards For Inground Swimming Pools In addition the installation of this diving board and or stand is not complete until you the installer have delivered to your customer and reviewed with your customer the Owners Manual as well as the Plan Your Dive Steer Up brochure ONLY ONE PERSON AT A TIME ON THE DIVING BOARD WITH A MAXIMUM WEIGHT LIMIT OF 250 LBS INTER FAB BOARD BASE COMPATIBILITY CHART DURO BEAM DURO SPRING TECHNI BEAM OLYMPIAN COMMERCIAL BASE TYPE g 10 6 8 110 U Stand 12 U1 U2 Ue U Stand 18 5 U1 U1 U2 U2 U2 U Stand 24 U1 U2 CHART KEY 5 STANDARD U1 UPGRADE 1 Ue UPGRADE 2 US UPGRADE 3 NOT AVAILABLE NOTE The Chart above refers to standard wood core diving boards and standard fiberglass and steel diving bases U STAND M Rev 3 09 BK USTAND BOOK 4 INSTALLATION MANUAL U STAND RESIDENTIAL INGROUND PO
46. xceed 6 inches 15 em 7 Decks and deck equipment 7 1 Decks shall comply with 7 1 1 through 7 1 17 as applicable 7 1 1 Deck s shall be designed and installed in accordance with the engineering methods required by the authority having jurisdiction U STAND IM Rev 3 09 BK USTAND BOOK 22 requirements a concrete deck shall be designed and constructed in accordance with the recommended practices of the most recent edition of American Concrete Institute ACI Standard 302 1R 96 Guide for concrete floor and slab construction or in accor dance with the requirements of the local authority the authority having jurisdiction or both The deck shall be designed and constructed to meet the appli cable requirements of the Americans with Disabilities Act 7 1 2 Decks ramps coping and similar step surfaces shall be slip resisting and cleanable 7 1 3 Special features in or on deck s such as markers brand insignias or similar materials shall be slip resisting 7 1 4 Step risers for the deck shall be uniform and have a minimum height of 3 3 4 inches 9 5 cm and a maximum height of 7 1 2 inches 19 cm A handrail shall be provided for stairs having three or more risers The minimum tread distance from front to back shall be 11 inches 28 cm 7 1 5 The deck or unobstructed access shall be provided at a minimum of 65 of the pool perimeter to meet the requirement of the 10 20 rule See ap pendix H Glossary 7 1 5 1
Download Pdf Manuals
Related Search