Trademarks FOXWELL is trademark of Shenzhen Foxwell
Contents
1. AutoMaster Pro NT414 Manual_English_V1 00 5 2 Read Codes Read Codes menu lets you read both stored codes and pending codes found in the control unit Typical menu options include e Stored Codes e Pending Codes Diagnostic trouble codes stored in a control module are used to help identify the cause of a trouble or troubles with a vehicle These codes have occurred a specific number of times and indicate a problem that requires repair Pending codes are also referred to as maturing codes that indicate intermittent faults If the fault does not occur within a certain number of drive cycles depending on vehicle the code clears from memory If a fault occurs a specific number of times the code matures into a DTC and the MIL illuminates or blinks To read codes pending codes from a vehicle 1 Scroll with the arrow keys to highlight Read Codes from Diagnostic Menu and press the ENTER key Diagnostic Menu 1 System Status 2 Read Codes 3 Erase Codes CICTT O Figure 5 3 Sample Diagnostic Menu Screen 2 Select Stored Codes Pending Codes and press the ENTER key to confirm A code list including code number and its description displays Read Codes 1 Stored Codes 2 Pending Codes Figure 5 4 Sample Read Codes Screen If no DTCs are present the message No Pending Codes Found is displayed If any manufacturer specific or enhanced codes detected select vehicle a make before viewing DTC information 28 Auto2. J338 Throttle Actuator J338 Engine Coolant Temp Sensor on Radiator Outlet G83 Intake Air Temp Sensor G42 Figure 4 21 Sample Code Screen 20 AutoMaster Pro NT414 Manual_English_V1 00 3 Press function key Save to store DTC information Or use the BACK key to exit 4 3 2 Freeze Frame Data gt Freeze Frame Data menu displays freeze frame data a snapshot of critical vehicle operating conditions automatically recorded by the on board computer at the time of the DTC set Itis a good function to help determine what caused the fault To view freeze frame data 1 Select Freeze Frame Data from the Function Menu Details of freeze frame data displays Function menu 1 Read Codes 2 Freeze Frame Data 3 Erase Codes 4 ECU information 5 Live Data Figure 4 22 Sample function menu screen 2 Use the arrow keys to scroll back and forth through different screens of data Freeze Frame Data Load 0 0 0 km h 12 C 40 C 0 00 mbar 0 000V 5 5 BTDC LA speed Temperature Temperature Absolute pressure Voltage Timing angle Figure 4 22 Sample Freeze Data screen 3 Press function key Save to store freeze frame information Or use the BACK key to exit 4 3 3 Erase Codes Erase Codes menu lets you to clear all current and stored DTCs from a selected control module Also it erases all temporary ECU information including freeze frame So make sure that the selected system are completely checked
3. protocol to communicate this function is not supported by vehicle Refer to On Board Monitor Tests on page 38 39 for O2 monitor data of CAN equipped vehicles P To retrieve O2 monitor data 1 Scroll with the arrow keys to highlight O2 Monitor Test from Diagnostic Menu and press the ENTER key A screen with a list of available sensors displays Diagnostic Menu 1 System Status 2 Read Codes 3 Erase Codes 4 Live Data 5 Freeze Frame 6 I M Readiness 7 02 Monitor Test 8 On board Monitor Test Figure 5 23 Sample Diagnostic Menu Screen 2 Scroll with the arrow keys to highlight an O2 sensor and press the ENTER key to confirm A screen with details of the selected sensor displays O2 Monitor Tes 1 02 Bank1 Sensor 2 O2 Bank1 Sensor2 Figure 5 24 Sample O2 Monitor Test screen 3 Use the up and down arrow keys to scroll through data to select lines and left and right arrow keys to scroll back and forth through different screens of data 37 AutoMaster Pro NT414 Manual_English_V1 00 O2 Bank1 Sensor T Figure 5 25 Sample O2 Bank1 Sensor 1 Screen 4 Press Enter key to view data of selection 81 Module Test Value 10 Min Limit Max Limit Figure 5 26 Sample data of 81 screen 5 Press the BACK key to exit and return 5 8 On Board Monitor Test The On Board Monitor Test function is useful after servicing or after clearing a vehicle ECU s memory It receives test results for emission related
4. specific legal rights and the Consumer may also have other rights which vary from state to state 3 AutoMaster Pro NT414 Manual_English_V1 00 Safety Information For your own safety and the safety of others and to prevent damage to the equipment and vehicles read this manual thoroughly before operating your scanner The safety messages presented below and throughout this user s manual are reminders to the operator to exercise extreme care when using this device Always refer to and follow safety messages and test procedures provided by vehicle manufacturer Read understand and follow all safety messages and instructions in this manual Safety Message Conventions Used We provide safety messages to help prevent personal injury and equipment damage Below are signal words we used to indicate the hazard level in a condition A DANGER Indicates an imminently hazardous situation which if not avoided will result in death or serious injury to the operator or to bystanders Indicates a potentially hazardous situation which if not avoided could result in death or serious injury to the operator or to bystanders Indicates a potentially hazardous situation which if not avoided may result in moderate or minor injury to the operator or to bystanders Important Safety Instructions And always use your scanner as described in the user s manual and follow all safety messages e Do not route the test cable in a manner that would interfe
5. 2 screens will be present Use the up and down arrow keys to scroll through data to select lines and left and right arrow keys to scroll back and forth through different screens of data Since DTCs cleared Malfunction Indicator lamp MIL Status OFF e B Misfire Monitoring gt gt O 6IXIXIX Fuel system Monitoring O N Comprehensive component Monitoring Catalyst Monitoring Heated Catalyst Monitoring A N O Evaporative system Monitoring lt Secondary air system Monitoring N A Figure 5 21 Sample IM Readiness Screen 1 Or This Drive Cycle Malfunction Indicator lamp MIL Status O MA A ALA Misfire Monitoring Fuel system Monitoring A Comprehensive component Monitoring Catalyst Monitoring INC Heated Catalyst Monitoring N A Evaporative system Monitoring INC Secondary air system Monitoring N A Figure 5 22 Sample IM readiness screen 2 3 Press the BACK key to exit 36 AutoMaster Pro NT414 Manual_English_V1 00 5 7 O2 Monitor Test OBD II regulations require certain vehicles monitor and test oxygen O2 sensors to isolate fuel and emissions related faults The O2 Monitor Test function is used to retrieve completed O2 sensors monitor test results The O2 Monitor Test is not an on demand test O2 sensors are not tested when selected via the menu but tested when engine operating conditions are within specified limits If the vehicle uses a controller area network CAN
6. and serviced by technicians and no vital information will be lost before clearing codes NOTE e To clear codes make sure that the ignition key is switched to ON with the engine off e Erase Codes does not fix the problem that caused the fault DTCs should only be erased after correcting the condition s that caused them To clear codes 1 Scroll with the arrow keys to highlight Erase Codes from Function Menu and press the ENTER key 21 AutoMaster Pro NT414 Manual_English_V1 00 Function menu i 1 Read Codes 2 Freeze Frame Data 3 Erase Codes 4 ECU information 5 Live Data Figure 4 23 Sample Function Menu Screen 2 Follow the on screen instructions and answer questions about the vehicle being tested to complete the procedure Erase Codes DTC and Freeze Data will be lost Do you wish to continue Figure 4 24 Sample Erase Codes Screen 3 Check the codes again If any codes remain repeat the Erase Codes steps 4 3 4 ECU Information ECU Information screen displays the identification data of the control module under test such as the control module identification string and the control module coding gt To read ECU information 1 Select ECU Information from the menu and press the ENTER key Function menu 1 Read Codes 2 Freeze Frame Data 3 Erase Codes 4 ECU information 5 Live Data Figure 4 25 Sample Function Menu Screen 22 AutoMaster Pro NT414 Manual_English_V1 00 2 A screen with detailed
7. identify the cause of a trouble or troubles with a vehicle These codes have occurred a specific number of times and indicate a problem that requires repair Pending codes are also referred to as maturing codes that indicate intermittent faults If the fault does not occur within a certain number of drive cycles depending on vehicle the code clears from memory If a fault occurs a specific number of times the code matures into a DTC and the MIL illuminates or blinks History codes are also referred to as past codes that indicate intermittent DTCs that are not currently active Code history is number of engine starts since DTC s were first detected to see if they are current or intermittent Self diagnostic lets you manually activate system tests that check for DTCs Usually it includes a KOEO Key on engine off test and a KOER key on engine running test P To read codes from a vehicle 1 Scroll with the arrow keys to highlight Read Codes from Function Menu and press the ENTER key A code list including code number and its description displays 1 Read Codes 2 Freeze Frame Data 3 Erase Codes 4 ECU information 5 Live Data Figure 4 20 Sample Function menu screen 2 Use the up and down arrow keys to scroll through data to select lines and left and right arrow keys to scroll back and forth through different screens of data 01 Engine Power supply Teminal 30 No fault type l identified Throttle Actuator
8. information of the selected control module displays ECU Information 1K0907115A 00412 Figure 4 26 Sample ECU Information Screen 3 Press function key Save to store ECU information Or use the BACK key to exit 4 3 5 Live Data Live Data menu lets you view and record real time PID data from a selected vehicle electronic control module Menu options typically include e Complete Data List e Custom Data List 4 3 5 1 Complete Data List Complete Data List menu lets you view all live PID data from a selected system gt To view all live PID data 1 Scroll with the arrow keys to highlight Live Data from the menu and press the ENTER key to display the live data menu 1 Complete List 2 Custom List Figure 4 27 Sample Live Data Selection Screen 2 Select the Complete List from the menu and press the ENTER key to display the datastream screen 23 AutoMaster Pro NT414 Manual_English_V1 00 Complete List ENGINE SPEED rpi at VEHICLE SPEED SENSOR ABSOLUTE THROTTLE POS BATTERY VOLTAGE 0 1 WHEEL SPD SENSOR FL 1 Y 231156 ne ele Figure 4 28 Sample Complete List Screen SHIFT LEVER SWITCH 3 Scroll with the up and down arrow keys to highlight a line if the One Graphic on the bottom is highlighted it indicates the graphing is available for the selected line Press the function key One Graphic to display the PID graph Engine Speed Figure 4 29 Sample PID graph Screen 4 Press the func
9. monitor e INC Incomplete vehicle was not driven enough to complete the monitor e N A Not Applicable vehicle does not support that monitor There are two types of I M Readiness tests e Since DTCs Cleared shows status of the monitors since the DTCs were last cleared e This Drive Cycle shows status of monitors since the start of the current drive cycle Below is a list of abbreviations and names of OBD II monitors supported by the scanner 6 Evap System Mon___ Evaporative System Monitor 9 Oxygen Sens Mon Oxygen Sensor Monitor Oxygen Sens Htr Oxygen Sensor Heater Monitor 11 EGR System Mon Exhaust Gas Recirculation System Monitor NOTE e To review l M Readiness status make sure that the ignition key is switched to ON with the engine off e Not all monitors are supported by all vehicles A C Refrig Mon Air Conditioning Refrigerant Monitor To retrieve I M Readiness Status data 1 Scroll with the arrow keys to highlight I M Readiness from Diagnostic Menu and press the ENTER key If vehicle supports both types of monitors a screen for monitor type selection displays Select a monitor type and press the ENTER key 35 AutoMaster Pro NT414 Manual_English_V1 00 Diagnostic Menu 1 System Status 2 Read Codes 3 Erase Codes 4 Live Data 5 Freeze Frame 6 I M Readiness 7 02 Monitor Test 8 On board Monitor Test E Figure 5 20 Sample Diagnostic Menu Screen 2 Depending on readiness test one of these
10. powertrain components and systems that are not continuously monitored for Non CAN vehicles And for CAN vehicles it receives test data for emission related powertrain components and systems that are and are not continuously monitored It is vehicle manufacturer who is responsible for assigning test and component IDs NOTE Test results do not necessarily indicate a faulty component or system gt To request on board monitor test results 1 Scroll with the arrow keys to highlight On Board Monitor Test from Diagnostic Menu and press the ENTER key 38 AutoMaster Pro NT414 Manual_English_V1 00 Diagnostic Menu 1 System Status 2 Read Codes 3 Erase Codes 8 On board Monitor Test Zi Figure 5 27 Sample Diagnostic Menu Screen 2 Depending on the protocol the vehicle used one of these 2 screens shows On Board Monitor ost 1 Test 01 Data EO 2 Test 02 Data 3 Test 05 Data 4 Test 06 Data Figure 5 28 Sample Non CAN Vehicle Test Screen Or On Board Monitor 1 O2 Monitor B1S1 2 02 Monitor B1S2 3 Catalyst Monitor B1 4 EGR Monitor Bank1 Figure 5 29 Sample CAN vehicle test screen 3 Scroll with the arrow keys to highlight a test group and press the ENTER key to confirm A screen with details of the selected sensor displays Use the up and down arrow keys to scroll through data to select lines and left and right arrow keys to scroll back and forth through different screens of data For non CAN vehicles t
11. press the function key Finish DTC Lookup Figure 5 40 Sample DTC Lookup Screen 3 A screen with code number and its definition displays If definition could not be found SAE or Manufacturer Specific the scanner displays DTC definition not found Please refer to vehicle service manual If a P1xxx C1xxx B1xxx or U1xxx code is entered select a vehicle make to look for DTC definitions Press the Back key to exit Trouble Codes Fuel Volume Regulator Control Circuit Open Figure 5 41 Sample Trouble Codes Screen 44 AutoMaster Pro NT414 Manual_English_V1 00 6 Playback Data The PlayBack option leads to screens for review of recorded test results gt To review recorded data 1 Scroll with the arrow keys to highlight PlayBack from home screen and press the ENTER key Application Manager Figure 6 1 Sample Home Screen 2 A screen with a list of test records displays If no data is recorded the message No Data available is displayed 1 Datastream gt scan MAKE EOBD savefile 2 Ecu Information gt scan MAKE EOBD savefile 3 Trouble Code gt scan MAKE USA Ford savefile 4 Trouble Code gt scan MAKE Asia Hyundai savefile 5 Ecu Information gt scan MAKE EUROPE Bmw savefile 6 Ecu Information gt scan MAKE EUROPE Fiat savefile 7 Ecu Information gt scan MAKE EOBD savefile Figure 6 2 Sample Playback Screen 3 Scroll with the arrow keys to highlight a vehicle record and press the EN
12. solvents such as alcohol to clean keypad or display Use a mild nonabrasive detergent and a soft cotton cloth 2 2 Accessory Descriptions This section lists the accessories that go with the scanner If you find any of the following items missing from your package contact your local dealer for assistance 1 User s Guide provides operation instructions for the usage of the scanner 2 USB Cable provides connection between the scanner and a computer to upgrade the tool 3 Memory Card contains the scanner s operating software and applications IMPORTANT Do not remove the memory card unless performing updates to the card 4 Diagnostic Cable provides connection between the scan tool and vehicle 5 Blower Molding Case stores the scanner and its accessories 2 3 Technical Specifications Display Backlit 480 272 TFT color display Working Temperature 0 to 60 C 32 to 140 F Storage Temperature 20 to 70 C 4 to 158F Power Supply 8 18V vehicle power 12V AC DC power 3 3V USB power Dimensions L W H 200 130 40mm Gross Weight 1 8Kg Protocols SAE J1850 VPW and PWM ISO 9141 2 ISO 14230 2 KWP 2000 ISO 15765 4 CAN 3 Getting Started 3 1 This section describes how to provide power to the scanner provides brief introductions of applications loaded on the scanner and display screen layout and illustrates how to input text and numbers with the scan tool Providing Power to Scanner Before using the scanne
13. vehicle 4 1 3 Manual Vehicle Selection Manual Vehicle Selection identifies a vehicle by making several selections according to certain VIN characters such as model year and engine type gt To identify a vehicle by manual vehicle selection 1 Refer to Step 1 3 of 4 1 1 Automatic VIN Acquisition 2 On each screen that appears select the correct option and then press the ENTER key Do this until the complete vehicle information is entered and the menu of controller selection displays Model Year s 1 D 2013 B 2 C 2012 l 5 9 2009 Vehicle Model IAS 1 Passenger Car B 7 2007 2 LD Trk MPV Incomplete ce ol 8 6 2006 Vehicle Type ll 1 Chevrolet 2 Cadillac Figure 4 9 Sample Manual Vehicle Selection Screen 4 1 4 Vehicle Data Recorder The scan tool is able to save a tested vehicle by creating a Vehicle Record It provides quick identification of previously tested vehicle s NOTE The Vehicle Record option will not show if no record of previously identified vehicle is created P To create a vehicle record 1 Identify the vehicle by any of the means above and run an automatic system test by selecting Auto Scan Main Groups la 1 Auto Scan 2 Control Unit Figure 4 9 Sample System Menu Screen 2 When the test finished press the function key Save on the screen and a screen with a QWERTY keyboard displays Save Vehicle Record Figure 4 10 Sample Save Vehicle Record Screen
14. you to minimize the number of PIDs on the data list and focus on any suspicious or symptom specific data parameters To create a custom data list 1 Select Custom List from the menu and press the ENTER key Live Data 1 Complete List 2 Custom List Figure 5 15 Sample Live Data Menu Screen 2 The custom datastream selection screen displays Scroll with the up and down arrow keys to highlight a line press the ENTER key and then repeat the action to make more selections Ei Numbers of DTCs lt PEETE gt CCC A Engine Coolant Temperature 5 T Short Term Fuel Trim Bank 1 e x Long Term Fuel Trim Bank 1 Figure 5 16 Sample Custom Datastream Selection Screen NOTE To deselect an item select it again and then press the ENTER key Alternatively use the function keys SELECT ALL and CLEAR ALL to select or deselect all items at once 3 When finished selection use the function key VIEW DATA to display selected items 33 AutoMaster Pro NT414 Manual_English_V1 00 Custom List E Number of DTCs 0 Fuel Systems 1 Status Fuel Systems2 Status Engine Coolant Temperature Short Term Fuel Trim Bank 1 Y Figure 5 17 Sample Datastream Screen JA Calculate load value fo 5 5 Freeze Frame Freeze Frame menu displays freeze frame data a snapshot of critical vehicle operating conditions automatically recorded by the on board computer at the time of the DTC set Itis a good function to he
15. 3 Enter a unique name for this vehicle and save it and you will see this new vehicle in Vehicle Data Recorder menu Vehicle record 1 VW JETTA 2 VW Sagitar Figure 4 11 Sample Vehicle Record Screen P To identify a previously tested vehicle 1 Select Vehicle record and press the ENTER key to start Main Groups 1 Auto scan 2 Control unit 3 Vehicle record 16 AutoMaster Pro NT414 Manual_English_V1 00 Figure 4 12 Sample tested vehicle identification screen 2 Select the vehicle under test and press the ENTER key 4 2 System Selection When you have completed the identification of vehicle a menu for selecting system to test displays Menu options typically include e Auto Scan e Control Unit 4 2 1 Auto Scan Auto Scan performs an automatic system test to determine which control modules are installed on the vehicle and obtain diagnostic trouble codes DTCs overview Depending on the number of control modules it may take a few minutes to complete the test P To perform an automatic system scan 1 Scroll with the arrow keys to highlight Auto Scan from the menu and press ENTER to start Main Groups 1 Auto Scan 2 Control Unit Figure 4 13 Sample Select System Scan Screen 2 To pause the scan press the function key corresponding with Pause on the screen 2 Auto Scan 1 01 Engine Fault 20 2 02 Auto Trans Scanning Figure 4 14 Sample Automatic system scan screen 3 At the en
16. AR PURPOSE OR USE SHALL BE LIMITED TO THE DURATION OF THE FOREGOING LIMITED WRITTEN WARRANTY OTHERWISE THE FOREGOING LIMITED WARRANTY IS THE CONSUMER S SOLE AND EXCLUSIVE REMEDY AND IS IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED FOXWELL SHALL NOT BE LIABLE FOR SPECIAL 2 AutoMaster Pro NT414 Manual_English_V1 00 INCIDENTAL PUNITIVE OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO LOSS OF ANTICIPATED BENEFITS OR PROFITS LOSS OF SAVINGS OR REVENUE LOSS OF DATA PUNITIVE DAMAGES LOSS OF USE OF THE PRODUCT OR ANY ASSOCIATED EQUIPMENT COST OF CAPITAL COST OF ANY SUBSTITUTE EQUIPMENT OR FACILITIES DOWNTIME THE CLAIMS OF ANY THIRD PARTIES INCLUDING CUSTOMERS AND INJURY TO PROPERTY RESULTING FROM THE PURCHASE OR USE OF THE PRODUCT OR ARISING FROM BREACH OF THE WARRANTY BREACH OF CONTRACT NEGLIGENCE STRICT TORT OR ANY OTHER LEGAL OR EQUITABLE THEORY EVEN IF FOXWELL KNEW OF THE LIKELIHOOD OF SUCH DAMAGES FOXWELL SHALL NOT BE LIABLE FOR DELAY IN RENDERING SERVICE UNDER THE LIMITED WARRANTY OR LOSS OF USE DURING THE PERIOD THAT THE PRODUCT IS BEING REPAIRED 6 Some states do not allow limitation of how long an implied warranty lasts so the one year warranty limitation may not apply to you the Consumer Some states do not allow the exclusion or limitation of incidental and consequential damages so certain of the above limitations or exclusions may not apply to you the Consumer This limited warranty gives the Consumer
17. D ad a adanans 49 0 TOOL INE OR MATION AAA A A 50 Tf CONFIGURE SHORTCUT KEYS NS oeaamaa tara 50 6 AutoMaster Pro NT414 Manual_English_V1 00 1 Using This Manual We provide tool usage instructions in this manual Below is the conventions we used in the manual 1 1 Bold Text Bold text is used to highlight selectable items such as buttons and menu options Example Press the ENTER button to select 1 2 Symbols and Icons 1 2 1 Solid Spot Operation tips and lists that apply to specific tool are introduced by a solid spot e Example When System Setup is selected a menu that lists all available options displays Menu options include e Languages e Unit e Beep e Keypad Test e LCD Test e About e Shortcuts 1 2 2 Arrow Icon gt An arrow icon indicates a procedure Example gt To change menu language 1 Scroll with the arrow keys to highlight Language on the menu 2 Press the ENTER button to select 1 2 3 Note and Important Message Note A NOTE provides helpful information such as additional explanations tips and comments Example NOTE Test results do not necessarily indicate a faulty component or system Important IMPORTANT indicates a situation which if not avoided may result in damage to the test equipment or vehicle Example IMPORTANT Do not soak keypad as water might find its way into the scanner 7 AutoMaster Pro NT414 Manual_English_V1 00 2 Introduction AUTOMASTER PRO series scanner
18. FOXWELL in repairing or replacing the defective parts 2 The customer shall have no coverage or benefits under this limited warranty if any of the following conditions are applicable a The product has been subjected to abnormal use abnormal conditions improper storage exposure to moisture or dampness unauthorized modifications unauthorized repair misuse neglect abuse accident alteration improper installation or other acts which are not the fault of FOXWELL including damage caused by shipping b The Product has been damaged from external causes such as collision with an object or from fire flooding sand dirt windstorm lightning earthquake or damage from exposure to weather conditions an Act of God or battery leakage theft blown fuse improper use of any electrical source or the product was used in combination or connection with other product attachments supplies or consumables not manufactured or distributed by FOXWELL 3 The customer shall bear the cost of shipping the product to FOXWELL And FOXWELL shall bear the cost of shipping the product back to the customer after the completion of service under this limited warranty 4 FOXWELL does not warrant uninterrupted or error free operation of the product If a problem develops during the limited warranty period the consumer shall take the following step by step procedure a The customer shall return the product to the place of purchase for repair or replacement proce
19. Following applications are preloaded into the scanner e OBDII EOBD leads to OBDII screens for all 9 generic OBD system tests e Scan leads to screens for diagnostic trouble code information live datastream ECU information on 49 vehicle makes sold worldwide e Setup leads to screens for adjusting default settings to meet your own preference and view information about the scanner e Playback leads to screens for access saved data files e Oil Reset leads to screens for resetting oil service light oil inspection light service mileage service intervals and more e EPB leads to screens for diagnostic trouble code information live datastream ECU information special functions of electric parking brake systems Application Manager Figure 3 1 Sample Home Screen 3 3 Input Dialog Box This section illustrates how to use the scan tool to input letters and numbers such as VIN number channel number test values and DTC number Typically you may be required to input letters or numbers when you are doing any of the following operations e VIN entry e input channel number e set adaptation value 10 AutoMaster Pro NT414 Manual_English_V1 00 e enter block number e enter login code e key matching e look up DTCs The scan tool provides 4 different types of keyboard to meet your specific needs Depending on the needs of text entry it automatically shows the most suitable keypad e classic QWERTY keyboad for i
20. Master Pro NT414 Manual_English_V1 00 Trouble Codes No codes are stored in the module Figure 5 5 Sample No Codes Screen 3 Use the up and down arrow keys to scroll through data to select lines and left and right arrow keys to scroll back and forth through different screens of data Trouble Codes E LESI Intake Air Temperature Sensor 1 Circuit High E P0123 510 Throttle Pedal Position Sensor Switch A Circuit High P0222 10 Throttle Pedal Position Sensor Switch B Circuit Low P2122 10 Throttle Pedal Position Sensor Switch D Circuit Low P2127 10 Throttle Pedal Position Sensor Switch E Circuit Low U0001 10 High Speed CAN Communication Bus P0100 510 Mass or Volume Air Flow A Circuit Figure 5 6 Sample Code screen 4 Press function key Save to store DTC information Or use the BACK key to exit 5 3 Erase Codes Erase Codes menu lets you to clear all current and stored DTCs from the control module Also it erases all temporary ECU information including freeze frame So make sure that the selected system are completely checked and serviced by technicians and no vital information will be lost before clearing codes NOTE e To clear codes make sure that the ignition key is switched to ON with the engine off e Erase Codes does not fix the problem that caused the fault DTCs should only be erased after correcting the condition s that caused them gt To clear codes 1 Scroll with the arrow keys to highlight Er
21. TER key Details of the test record displays Use the up and down arrow keys to scroll through data to select lines Read Codes Intake Air Temperature Sensor 1 Circuit High Throttle Pedal Position Sensor Switch A Circuit High Throttle Pedal Position Sensor Switch B Circuit Low Throttle Pedal Position Sensor Switch D Circuit Low Throttle Pedal Position Sensor Switch E Circuit Low High Speed CAN Communication Bus Mass or Volume Air Flow A Circuit Figure 6 3 Sample Test Data Details Screen 45 AutoMaster Pro NT414 Manual_English_V1 00 4 lf you are reviewing live data or freeze frame data use the function key Next Frame or Pre Frame to scroll through all possible frames when necessary 1 of 4 Frame Numbers of DTCs Fuel system 1 status Fuel System 2 status Engine Coolant Temperature Short Term Fuel Trim Bank 1 Figure 6 4 Sample Test Data Details Screen Calculated Load Value E 5 To erase a record scroll with the arrow keys to highlight it and press the function key Delete To delete all records press the function key Delete All Answer Yes to delete and No to quit 7 System Setup This section illustrates how to program the scanner to meet your specific needs When Setup application is selected a menu with available service options displays Menu options typically include e Language e Unit e Beep Set e Key Test e LCD Test e About e Shortcuts 7 1 Select Language Selecting Language open
22. Trademarks FOXWELL is trademark of Shenzhen Foxwell Technology Co Ltd All other marks are trademarks or registered trademarks of their respective holders Copyright Information 2015 Shenzhen Foxwell Technology Co Ltd All rights reserved Disclaimer The information specifications and illustrations in this manual are based on the latest information available at the time of printing Foxwell reserves the right to make changes at any time without notice Visit our website at www foxwelltech com For Technical Assistance send us email at support foxwelltech com 1 AutoMaster Pro NT414 Manual_English_V1 00 One Year Limited Warranty Subject to the conditions of this limited warranty Shenzhen Foxwell Technology Co Ltd FOXWELL warrants its customer that this product is free of defects in material and workmanship at the time of its original purchase for a subsequent period of one 1 year In the event this product fails to operate under normal use during the warranty period due to defects in materials and workmanship FOXWELL will at its sole option either repair or replace the product in accordance with the terms and conditions stipulated herein Terms and Conditions 1 If FOXWELL repairs or replaces the product the repaired or replaced product shall be warranted for the remaining time of the original warranty period No charge will be made to the customer for replacement parts or labor charges incurred by
23. and make a series of choices Each selection you make advances you to the next screen A Back button in the upper left corner of the screen returns you to the previous screen Exact procedures may vary somewhat by vehicle It typically identifies a vehicle by any of the following means e Automatic VIN acquisition e Manual VIN entry e Manual vehicle selection e Vehicle data recorder NOTE Not all identification options listed above are applicable to all vehicles Available options may vary by vehicle manufacturer 4 1 1 Automatic VIN Acquisition gt Automatic VIN Acquisition allows to identify a vehicle by automatically requesting the vehicle identification number VIN To identify a vehicle automatic VIN acquisition 1 Scroll with the arrow keys to highlight Scan from the Application menu and press the ENTER key to start If you have the application assigned to one of the function keys at the bottom of the screen you can alternatively press the function key to start the application Application Manager Figure 4 1 Sample Application Menu 2 A screen with vehicle manufacturer areas displays Select the area where the vehicle manufacturer is from A menu of all vehicle manufacturers from this area displays 12 AutoMaster Pro NT414 Manual_English_V1 00 Application Scan European Figure 4 2 Sample Vehicle Manufacturer Area Selection Screen 3 Select the vehicle manufacturer A list of vehicle identification op
24. ase Codes from Diagnostic Menu and press the ENTER key 29 AutoMaster Pro NT414 Manual_English_V1 00 Diagnostic Menu 1 System Status 2 Read Codes 3 Erase Codes 4 Live Data 5 Freeze Frame 6 I M Readiness 7 O2 Monitor Test 8 On board Monitor Test Figure 5 7 Sample Diagnostic Menu Screen 2 Follow the on screen instructions and answer questions about the vehicle being tested to complete the procedure Erase Codes DTC and Freeze Data will be lost Do you wish to continue Figure 5 8 Sample Erase Codes Screen 3 Check the codes again If any codes remain repeat the Erase Codes steps 5 4 Live Data Live Data menu lets you view and record real time PID data from the electronic control module Menu options typically include e Complete Data List e Custom Data List 5 4 1 Complete Data List Complete Data List menu lets you view all live PID data from a selected system To view all live PID data 1 Scroll with the arrow keys to highlight Live Data from Diagnostic Menu and press the ENTER key 30 AutoMaster Pro NT414 Manual_English_V1 00 Diagnostic Menu 1 System Status 2 Read Codes 3 Erase Codes 4 Live Data f Figure 5 9 Sample Diagnostic Menu Screen 2 Select Complete List from the menu and press the ENTER key to display the datastream 1 Complete List screen 2 Custom List Figure 5 10 Sample Live Data Menu Screen 3 Use the up and down arrow keys to scroll through da
25. cations displays ShortCuts 1 Edit ShortCuts F1 Function 2 Edit ShortCuts F2 Function 3 Edit ShortCuts F3 Function Figure 7 13 Sample ShortCuts Screen 3 Scroll with the UP DOWN arrow keys to highlight an application and press the ENTER key to assign the application to the shortcut key 4 Press any key to exit and return 51 AutoMaster Pro NT414 Manual_English_V1 00
26. cecauaseeesecens 12 Ak TAGOM VIN AUSTIN rr A tie 12 Az Manua VANCE AS 14 1 3 Manual Vehicle SElECTIOM sia e e O ets ee ia do ade eas 15 4 1 4 Vehicle Data RECOrdED ccc ccc ceeecececccccccssecccccccccsccecceccecaussececcceccausscesececensauceececcecanatececeeceeaens 15 ARSS TE ee ON EE EEE eel la on cee 17 AZ AN US O II IR A IN 17 AA js A A A N 18 4 3 DIAGNOSTIC FUNCTION SELECTION c cccscecceccccccccccccccccsnsssssseseceeececcececccecceceecauauuststseeeeeeeceeceececceeeueaas 19 FATES MA wots 8 al ll 19 4 3 2 Freeze Frame Di ai iria 21 o O O 21 SN a A An 22 MEE eo fd MANY A CE NDT TO See ONT OAT AEE CR CEN A Te ee Re eee INE Tey 23 AS 20s i COM Cte Data Sr O rai 23 5 AutoMaster Pro NT414 Manual_English_V1 00 4 3 52 C stom Data Bh EB oe ee aa a OPO ne en UR ROS e e Oe nn Ae 25 SOBDIVEOBD OPERATION Sissi ao 26 LOS TEM PATS S NS Sanaa ane 27 READ CODE airar E ca 28 JO ERASE CODES Sd a 29 ALVE DATA aaa 30 a GOomplete Data sb A AA ES 30 OZ CUS OM Da asta ira dida lada 33 5 5 FREEZE FRAME a 34 5 6 ReaD I M READINESS STATUS DATA ita O aaa 35 5 0 OZ MONITOR TES Tasa 37 IO ON BOARD MONITOR TEST daa 38 99 COMPONENT TEST Ao 40 5210 REQUEST VEHICLE INFORMATION aaa 41 Sl MODULES PRESEN LA AAA 43 A TS a aah dana aetna cena aeetsee a ana N 43 6 PLAYBACK DATA ai sa 45 TV TWN SETUP ados 46 TAUSBLES TP LANGUAGE isos 46 AR A A ate aot AE O 47 3 CONFIGURE BEEPER ads A A A A AR 48 PTET KEYPAD tii io ei 48 TO ECD EYP A
27. d of successful automatic controller scan a menu with a list of installed controllers together with their DTC overview displays 17 AutoMaster Pro NT414 Manual_English_V1 00 Auto Scan 3 PDME R Pass No Fault EPS Mode N A BCM Pass No Fault E ABS VDC Pass No Fault Airbag Pass No Fault AT CVT Mode N A 9 ICC Scanning Figure 4 15 Sample auto scan screen 4 If there is diagnostic trouble code s detected in a control unit press the function key corresponding with Display DTC on the screen to view details of code information and press the function key Quick Erase to clear them 01 Engine Power supply Teminal 30 No fault type identified Throttle Actuator J338 Throttle Actuator J338 Engine Coolant Temp Sensor on Radiator Outlet G83 Intake Air Temp Sensor G42 Figure 4 16 Sample Display DTC screen 5 Select the system you would like to test and press the ENTER key When the scanner has established connection with the vehicle the Function Menu displays Function menu 1 Read Codes 2 Freeze Frame Data 3 Erase Codes 4 ECU information 5 Live Data Figure 4 17 Sample Function Menu screen 4 2 2 Control Unit Control Unit screen displays all controllers available of the vehicle manufacturer The controllers listed on the menu do not mean that they are installed on the vehicle 18 AutoMaster Pro NT414 Manual_English_V1 00 To select a system for testing 1 Scroll with the arrow keys
28. entifications Figure 5 36 Sample Calibration ID Screen 4 Press function key Save to store the readiness data Or use the BACK key to exit and return 42 AutoMaster Pro NT414 Manual_English_V1 00 5 11 Modules Present The scanner identifies module IDs and communication protocols for OBD2 modules in the vehicle P To view module IDs and communication types 1 Scroll with the arrow keys to highlight Modules Present from Diagnostic Menu and press the ENTER key Diagnostic Menu I M Readiness 7 O2 Monitor Test 8 On board Monitor Test 9 Component Test 10 Vehicle Info 11 Modules Present 12 DTC Lookup System Status Figure 5 37 Sample Diagnostic Menu Screen 2 A screen with the module IDs and protocols displays Module Present Protocol Eo KWP 2000 Figure 5 38 Sample Module Present Screen 3 Press function key Save to store the readiness data Or use the BACK key to exit and return 5 12 DTC Lookup DTC Lookup menus allows to request DTC definitions stored in the scan tool gt To Look up DTCs 1 Scroll with the arrow keys to highlight DTC Lookup from Diagnostic Menu and press the ENTER key 43 AutoMaster Pro NT414 Manual_English_V1 00 Diagnostic Menu 6 I M Readiness 7 O2 Monitor Test 8 On board Monitor Test 9 Component Test 10 Vehicle Info 11 Modules Present 12 DTC Lookup 1 System Status Figure 5 39 Sample Diagnostic Menu Screen 2 Enter a valid code number and
29. est screen is illustrated as below 39 AutoMaster Pro NT414 Manual_English_V1 00 Test 01 Data Module Test Value Min Limit Max Limit Status Figure 5 30 Sample Non CAN vehicle test screen For CAN vehicles test screen is illustrated as below Test 01 Data 5 0 450 Figure 5 31 Sample Can vehicle test screen 4 Press the BACK key to exit and return 5 9 Component Test Component Test allows the scanner to control operation of vehicle components tests or systems NOTE e Some manufacturers do not allow tools to control vehicle systems e The manufacturer sets the criteria to automatically stop test Refer to appropriate vehicle service manual before using this function P To perform a component test 1 Scroll with the arrow keys to highlight Component Test from Diagnostic Menu and press the ENTER key A screen with a list of available tests displays 40 AutoMaster Pro NT414 Manual_English_V1 00 Diagnostic Menu I M Readiness 7 O2 Monitor Test 8 On board Monitor Test 9 Component Test 10 Vehicle Info 1 System Status Figure 5 32 Sample Diagnostic Menu Screen 2 Scroll with the arrow keys to highlight a system or component press the ENTER key to start test and the scanner displays the message Command Sent Component Tes 1 EVAP Sys Leak test Figure 5 33 Sample Component test screen 3 Press the BACK key to exit and return 5 10 Request Vehicle Information Vehicle Informa
30. etup menu and press the ENTER key Application Setup f Language Key Test Lcd Test GE ka ES About Shortcuts Figure 7 5 Sample Setup Screen 2 Press the LEFT RIGHT arrow key select an item and press the ENTER key to save and return Application Setup es A 6 di Language Lcd Test About Shortcuts ADM Figure 7 6 Sample Beeper On Off Selection Screen 7 4Test Keypad Selecting Key Test option opens a screen that allows you to check the functionality of the keypad gt To test the keypad 1 Scroll with the arrow keys to highlight Key Test from Setup menu and press the ENTER key 48 AutoMaster Pro NT414 Manual_English_V1 00 Application Setup Language Key Test Lcd Test e Shortcuts Figure7 7 Sample Setup Screen 2 Press any key to start test The virtue key corresponding with the key you pressed will be highlighted on the screen if it works correctly FOXWELL Press Any key to test Double F2 to return Figure 7 8 Sample Key Test Screen 3 To quit the test click the F2 function key twice 7 5 LCD Keypad Selecting LCD Test option opens a screen that allows you to check the functionality of the display gt To test the display 1 Scroll with the arrow keys to highlight LCD Test from Setup menu and press the ENTER key to start test Check if there are any missing spots in the LCD screen 49 AutoMaster Pro NT414 Manual_English_V1 00 Figure 7 9 Sample LCD Test Scree
31. lp determine what caused the fault gt To view freeze frame data 1 Select Freeze Frame from the Diagnostic Menu Details of freeze frame data displays Diagnostic Menu System Status l 2 Read Codes 3 Erase Codes 4 Live Data 5 Freeze Frame 6 I M Readiness 7 O2 Monitor Test 8 On board Monitor Test Figure 5 18 Sample Diagnostic Menu Screen 2 Use the up and down arrow keys to scroll through data to select lines and left and right arrow keys to scroll back and forth through different screens of data If no freeze frame detected the message No freeze frame data stored is displayed Freeze Frame Data 0 0000 1 Timing angle 5 5 BTDC 34 AutoMaster Pro NT414 Manual_English_V1 00 Figure 5 19 Sample Freeze Data Screen 3 Press function key Save to store freeze frame information Or use the BACK key to exit 5 6 Read I M Readiness Status Data gt I M Readiness option allows to view a snapshot of the operations for the emission system on OBDII EOBD vehicles I M Readiness is a useful function used to check if all monitors are OK or N A The vehicle s computer performs tests on the emission system during normal driving conditions After a specific amount of drive time each monitor has specific driving conditions and time required the computer s monitors decide if the vehicles emission system is working correctly When the monitor s status is e OK vehicle was driven enough to complete the
32. n 2 To quit the test press the Back key 7 6 Tool Information Selecting About option opens a screen that show information about your scan tool such as serial number and register password which may be required for product registration gt To view information of your scan tool 1 Scroll with the arrow keys to highlight About from Setup menu and press the ENTER key Application Setup zz 402 Language Unit Beep Key Test Lcd Test eN ha ES About Shortcuts SRD Figure 7 10 Sample Setup screen 2 A screen with detailed information of the scanner displays FOXWELL Product Serial Number AD1307000022 Register Password 000105 Copyright C 2012 Foxwell Technology Co Ltd All rights reserved Figure 7 11 Sample Tool Information Screen 3 Press the Back key to exit and return to the Setup menu 7 7 Configure Shortcut Keys Selecting Shortcuts option lets you to change the functionality of the shortcut buttons gt To assign a function to a shortcut button 1 Scroll with the arrow keys to highlight Shortcuts from Setup menu and press the ENTER key A screen with available shortcut keys displays 50 AutoMaster Pro NT414 Manual_English_V1 00 Application Setup Gm S Bs J Language Unit Beep Key Test Lcd Test ka ES About Shortcuts 11D Figure 7 12 Sample Setup screen 2 Press the UP DOWN arrow key select an shortcut key and press the ENTER key A screen with a list of loaded appli
33. n Screen NOTE To deselect an item select it again and then press the ENTER key Alternatively use the function keys SELECT ALL and CLEAR ALL to select or deselect all items at once 3 When finished selection use the function key VIEW DATA to display selected items Custom List Voltage Supply 12 032 j i Engine Speed min Ignition Timing Angle BTDC Throttle Drive Angle Sensor 1 Intake Air Mass Engine Speed Figure 4 34 Sample Datastream Screen 5 OBDII EOBD Operations OBD I I EOBD menu lets you access all OBD service modes According to ISO 9141 2 ISO 14230 4 and SAE J1850 standards the OBD application is divided into several sub programs called Service xx Below is a list of OBD diagnostic services e Service 01 request current powertrain diagnostic data e Service 02 request powertrain freeze frame data e Service 03 request emission related diagnostic trouble codes e Service 04 clear reset emission related diagnostic information e Service 05 request oxygen sensor monitoring test results e Service 06 request on board monitoring test results for specific monitored systems e Service 07 request emission related diagnostic trouble codes detected during current or last completed driving cycle e Service 08 request control of on board system test or component e Service 09 request Vehicle Information When OBDII EOBD application is selected from Home screen the scanner start
34. nput of texts that contain both letters and numbers e numeric keyboard for input of numbers e alphabet keyboard for input of letters e hexadecimal keyboard for special functions such as key matching UDS coding gt To input text with the scan tool 1 When you are requested to input text press the function key Keyboard and the keyboard displays Basic Setting Please input channel number 001 254 Figure 3 2 Sample Input Text Screen 2 Scroll with the arrow keys to highlight your desired letter or number and press the ENTER key to confirm Basic Setting Figure 3 3 Sample Numeric Keyboard Screen 3 To delete a letter or number use the function key Previous to move the cursor to it and then press the Backspace button 4 When finished the entry press Finish key to continue 11 AutoMaster Pro NT414 Manual_English_V1 00 4 Diagnostic Operations This section illustrates how to use the scanner to read and clear diagnostic trouble codes and view live data readings and ECU information on controllers installed on the vehicles and also save recordings of the data readings 4 1 Vehicle Identification The vehicle identification information presented is provided by the ECM of the vehicle being tested Therefore certain attributes of the test vehicle must be entered into the scan tool to ensure the data displays correctly The vehicle identification sequence is menu driven you simply follow the screen prompts
35. r make sure to provide power to the scanner The unit operates on any of the following sources e 12 volt vehicle power e USB connection to personal computer 3 1 1 Connecting to Vehicle Power The scanner normally powers on whenever it is connected to the data link connector DLC To connect to vehicle power 1 Locate the data link connector DLC The DLC is generally located under the dash on the driver side of the vehicle 2 Attached the diagnostic cable to the scanner and tighten the captive screws to ensure good connection 3 Connect a correct adapter to the data cable according to the vehicle being serviced and plug it into the vehicle DLC 9 AutoMaster Pro NT414 Manual_English_V1 00 4 Switch the ignition key to the ON position 5 The scanner automatically boots up IMPORTANT Never try to provide power for the scan tool from USB connection when the scan tool is communicating with a vehicle 3 1 2 Connecting to Personal Computer with USB Cable The scan tool also receives power through the USB port when it is connected to a PC for updating software and transferring saved files P To connect to PC 1 Insert the small end of the USB cable to the USB port at the right side of the scanner and the large end to a computer 2 Press the power switch of the scan tool to power it on 3 2 Application Overview When the scan tool boots up the Home screen opens This screen shows all applications loaded on the unit
36. re with driving controls e Do not exceed voltage limits between inputs specified in this user s manual e Always wear ANSI approved goggles to protect your eyes from propelled objects as well as hot or caustic liquids e Fuel oil vapors hot steam hot toxic exhaust gases acid refrigerant and other debris produced by a malfunction engine can cause serious injury or death Do not use the scanner in areas where explosive vapor may collect such as in below ground pits confined areas or areas that are less than 18 inches 45 cm above the floor e Do not smoke strike a match or cause a spark near the vehicle while testing and keep all sparks heated items and open flames away from the battery and fuel fuel vapors as they are highly flammable e Keep a dry chemical fire extinguisher suitable for gasoline chemical and electrical fires in work area e Always be aware of rotating parts that move at high speed when an engine is running and keep a safe distance from these parts as well as other potentially moving objects to avoid serious injury e Do not touch engine components that get very hot when an engine is running to avoid severe burns e Block drive wheels before testing with engine running Put the transmission in park for automatic transmission or neutral for manual transmission And never leave a running engine unattended e Do not wear jewelry or loose fitting clothing when working on engine 4 AutoMaster Pro NT414 Man
37. s a screen that allows you to choose system language The scan tool is set to display English menus by default gt To configure system language 1 Scroll with the arrow keys to highlight Language from Setup menu and press the ENTER key Application Setup T J Language Unit Beep Key Test Led Test D About Shortcuts Y Figure 7 1 Sample Setup Screen 46 AutoMaster Pro NT414 Manual_English_V1 00 2 Press the LEFT RIGHT arrow key select a language and press the ENTER key to confirm Press the Back key to exit and return Application Language English q espa ol Figure 7 2 Sample Language Selection Screen 7 2 Change Units Selecting Unit opens a dialog box that allows you to choose between US customary or metric units of measure P To change the unit setup 1 Scroll with the arrow keys to highlight Units from Setup menu and press the ENTER key Application Setup Language Key Test Lcd Test Shortcuts Figure 7 3 Sample Setup Screen 2 Press the LEFT RIGHT arrow key select an item and press the ENTER key to save and return Application Setup Language About Shortcuts wt English L Metric OIR 47 AutoMaster Pro NT414 Manual_English_V1 00 Figure 7 4 Sample Language Selection Screen 7 3 Configure Beeper Selecting Beep Set opens a dialog box that allows you to turn on off the beeper gt To turn on off the beeper 1 Scroll with the arrow keys to highlight Beep Set from S
38. s from Foxwell are innovative diagnostic tools for most vehicles on the road today With the tool properly connected to the vehicle s data link connector DLC you can use the scanner to read diagnostic trouble codes and view live data readings from all electronic vehicle control systems such as engine ABS and instrument cluster You can also save recordings of the data readings and print stored information 2 1 Scanner Descriptions This section illustrates external features ports and connectors of the scanner FOXWELL 2 2 5 4 7 8 Figure 2 1 Front View 1 Diagnostic Port provides connection between vehicle and the scanner 2 LCD Display shows menus test results and operation tips 3 Function Keys Shortcut keys three keys that correspond with buttons on some screens for executing special commands or provide quick access to most frequently used applications or functions 4 Direction Keys select an option or scroll through a screen of data or text 5 ENTER Key executes a selected option and generally goes to the next screen 6 BACK Key exits a screen and generally returns to previous screen 7 HELP Key displays helpful information 8 Power Switch turns on off the scanner and press and hold for 5 seconds for emergency reboots 9 SD Card Port holds the SD memory card for data backup and software update IMPORTANT 8 AutoMaster Pro NT414 Manual_English_V1 00 Do not use
39. s to detect the communicaiton protocol autometically Once the connection has established a menu that lists all of the tests available on the identified vehicle displays Menu options typically include e System Status 26 AutoMaster Pro NT414 Manual_English_V1 00 e Read Codes e Freeze Frame Data e Erase Codes e Live Data e M Readiness e O2 Sensor Test e On board Monitor Test e Component Test e Vehicle Information e Modules Present e Code Lookup NOTE Not all function options listed above are applicable to all vehicles Available options may vary by the year model and make of the test vehicle A The selected mode is not supported message displays if the option is not applicable to the vehicle under test 5 1 System Status System Status option open a screen with a summary of system status of the vehicle under test gt To view summary system status of a vehicle 1 Scroll with the arrow keys to highlight System Status from Diagnostic Menu and press the ENTER key Diagnostic Menu 1 System Status A gt 2 Read Codes 3 Erase Codes 4 Live Data 5 Freeze Frame 6 I M Readiness 7 O2 Monitor Test 8 On board Monitor Test Figure 5 1 Sample Diagnostic Menu Screen 2 A screen with detailed information displays System Status MIL Status O A a _ Code Found Monitors N A Monitors OK Monitors INC Srl E ont Ce Figure 5 2 Sample System Status Screen 27
40. ssing contact your local FOXWELL distributor or visit our website www foxwelltech com to get further information b The customer shall include a return address daytime phone number and or fax number complete description of the problem and original invoice specifying date of purchase and serial number c The customer will be billed for any parts or labor charges not covered by this limited warranty d FOXWELL will repair the Product under the limited warranty within 30 days after receipt of the product If FOXWELL cannot perform repairs covered under this limited warranty within 30 days or after a reasonable number of attempts to repair the same defect FOXWELL at its option will provide a replacement product or refund the purchase price of the product less a reasonable amount for usage e If the product is returned during the limited warranty period but the problem with the product is not covered under the terms and conditions of this limited warranty the customer will be notified and given an estimate of the charges the customer must pay to have the product repaired with all shipping charges billed to the customer If the estimate is refused the product will be returned freight collect If the product is returned after the expiration of the limited warranty period FOXWELL normal service policies shall apply and the customer will be responsible for all shipping charges 5 ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICUL
41. ta to select lines and left and right arrow keys to scroll back and forth through different screens of data Complete List Number of DTCs Fuel Systems 1 Status Fuel Systems2 Status Engine Coolant Temperature F Short Term Fuel Trim Bank 1 0 Calculate load value oo Figure 5 11 Sample Complete List Screen 4 Scroll with the up and down arrow keys to highlight a line if the One Graphic on the bottom is highlighted it indicates the graphing is available for the selected line Press the function key One Graphic to display the PID graph 31 AutoMaster Pro NT414 Manual_English_V1 00 Engine RPM 1225 rpm 2437 Figure 5 12 Sample PID Graph Screen 5 Press the function key Two Graphics to display two PID graphs in one screen Engine RPM 1237 rpm 2437 Figure 5 13 Sample Two PID Graph Screen 6 Press the function key Merge Graph to display two PID plots in one coordinate for easy and intuitive diagnosis Engine RPM Vehicle Speed Sensor Figure 5 14 Sample Merge Graph Screen 7 To record the data to memory of the scanner use the function key SAVE and press Stop Saving to stop recording at any time 8 Select Text to return to text viewing of PID data 9 Press Pause to suspend collecting data and use the Start key to resume collecting data 10 Use the Back key to return to diagnostic menu 32 AutoMaster Pro NT414 Manual_English_V1 00 5 4 2 Custom Data List Custom Data List menu lets
42. tion allows to request the vehicle s VIN number calibration ID s which identifies software version in vehicle control module s calibration verification numbers CVN s and in use performance tracking on model year 2000 and newer OBD II compliant vehicles CVNs are calculated values required by OBD II regulations They are reported to check if emission related calibrations have been changed Multiple CVNs may be reported for a control module It may take several minutes to do the CVN calculation In use performance tracking tracks performance of key readiness monitors NOTE Available options will vary depending on the vehicle under test To request vehicle information gt 1 Scroll with the arrow keys to highlight Vehicle Info from Diagnostic Menu and press the ENTER key 41 AutoMaster Pro NT414 Manual_English_V1 00 Diagnostic Menu 6 I M Readiness 7 O2 Monitor Test O Monitor Test 9 Component Test 10 Vehicle Info 11 Modules Present 12 DTC Lookup 1 System Status Figure 5 34 Sample Diagnostic Menu Screen 2 Follow on screen instruction and send the command to read vehicle information A screen with a list of available options displays Vehicle Info 1 Calibration ID Figure 5 35 Sample Vehicle Info Screen 3 Scroll with the arrow keys to highlight an available option and press the ENTER key A screen with details of the selected option displays Calibration ID Calibration 1K0907115A 0050 Id
43. tion key Two Graphics to display two PID graphs in one screen Engine Speed Desired Idle Speed Figure 4 30 Sample Two PID Graph Screen 5 Press the function key Merge Graph to display two PID plots in one coordinate for easy and intuitive diagnosis 24 AutoMaster Pro NT414 Manual_English_V1 00 Engine Speed Desired Idle Speed Figure 4 31 Sample Merged PID Plots Screen 6 To record the data to memory of the scanner use the function key SAVE and press Stop Saving to stop recording at any time 7 Press Text to return to text viewing of PID data 8 Select Pause to suspend collecting data from the scanner and use the Start key to resume collecting data 9 Press the Back key to return to the previous menu 4 3 5 2 Custom Data List Custom Data List menu lets you to minimize the number of PIDs on the data list and focus on any suspicious or symptom specific data parameters To create a custom data list 1 Select Custom List from the menu and press the ENTER key Live Data 1 Complete List 2 Custom List Figure 4 32 Sample Live Data Screen 2 The custom datastream selection screen displays Scroll with the up and down arrow keys to highlight a line press the ENTER key and then repeat the action to make more selections 25 AutoMaster Pro NT414 Manual_English_V1 00 Engine Speed af coon Temperature Fi Engine Speed aj Engine Load a Injection Timing E Figure 4 33 Sample Custom List Selectio
44. tions displays Application Scan European SS 8 Bentley Bugatti Citroen i EU Ford Figure 4 3 Sample Vehicle Manufacturer Selection Screen 4 Select Vin acquisition from the menu and press the ENTER key Vin acquisition 1 VIN CODE automatic acquisition 2 VIN CODE manual acquisition 3 Vehicle type manual acquisition Figure 4 4 Sample Vin Acquisition Screen 5 The scan tool starts to communicate with the vehicle and read the Vehicle Specification or VIN Code automatically 13 AutoMaster Pro NT414 Manual_English_V1 00 VIN CODE automatic acquisiti The VIN Code is VF1KGOMO529164173 Are you sure Figure 4 5 Sample VIN Automatic Acquisition 6 Answer YES if the Vehicle Specification or VIN code is correct and a menu of controller selection displays Answer NO if it is incorrect and you are required to enter the correct VIN number manually INPUT DATA LFPM5 ACP591 A76342 VIN Figure 4 7 Sample manual VIN entry screen 4 1 2 Manual VIN Entry Manual VIN Entry identifies a vehicle by manually inputting a 17 digit VIN code P To identify a vehicle by manual VIN entry 1 Refer to Step 1 3 of 4 1 1 Automatic VIN Acquisition 2 Select a appropriate option from the menu A virtual keyboard opens for VIN entry Enter VIN YV1AS565891101352 Figure 4 8 Sample Manual VIN Entry with Keyboard 3 Input a valid VIN code and use the function key Finish to confirm The scan tool starts to identify the
45. to highlight Control Unit from the menu and press the ENTER key A controller menu displays Control Unit 1 Common 2 Drivetrain 3 Chassis 4 Comfort Conv 5 Electronics 1 6 Electronics 2 Figure 4 18 Sample Control Unit Menu Screen 2 Select the system you would like to test When the scanner has established connection with the vehicle the Function Menu displays Common 01 Engine 02 Auto Trans 03 ABS Brake 08 Auto HVAC 19 Cent Elect Md 15 Airbags 16 Steering Wheel 17 Instruments e Figure 4 19 Sample Common menu screen 4 3 Diagnostic Function Selection After a system is selected and the scanner establishes communication with the vehicle the Function Menu displays The menu options may include e Read Codes e Freeze Frame Data e Erase Codes e ECU Information e Live Data NOTE Not all function options listed above are applicable to all vehicles Available options may vary by the year model and make of the test vehicle A The selected mode is not supported message displays if the option is not applicable to the vehicle under test 4 3 1 Read Codes Read Codes menu lets you read trouble codes found in the control unit Typical menu options include 19 AutoMaster Pro NT414 Manual_English_V1 00 e Present Permanent Current Codes e Pending Codes e History Codes e Code History e Self Diagnostic Present Permanent Current codes stored in a control module are used to help
46. ual_English_V1 00 Table of Contents ONE YEAR LIMITED WARRANTY u ccccccccccccccccccccscsscsscsscssssssccsccscccssccscccsscssccscccccccccccsccsccccsscsscees 2 SAFETY INFORMATION usa iaa 4 SAFETY MESSAGE CONVENTIONS USED ade SU GUOS 4 IMPORTANT SAFETY INSTRUCTIONS cccccecceccecccccccccccccaccessesesseceececcececceccceccecauauassstseseeeeececeecceceeeeecaeaaaaettetess 4 1 USING THIS MANUAL aa 7 AOS A IE T EZ SYMBOL SAND GOINGS ite hc sa te Meee tM ae ae ae ae ee eet E a a T ASA A EA E area ate Se cant a bane EA AE EEE AETI EE TE E SE 7 AZ PAM OC OM ae e ee A Raat at aint ete Gait Rain Bence ore mele Maat toe Gone T 1 2 3 Note and Important Message isnan a TA T7 2 INTRODUC TION a a EE a aa aa es ocx dE raaa de EECa 8 2 1 SCANNER DESCRIPTIONS a o eS 8 2 2 ACCESSORY DESCRIPTIONS emen aaa cun a o e a caos a DOS 9 2 3 TECHNICAL SPECIFICATIONS o wn thavianc cee telus diversos dsd 9 3 GETTING STARTED Us 9 3 1 PROVIDING POWER TO SCANNER ads 9 3 1 1 Connecting to Vehicle POWeT ooooccconccconanonannnoonanonanaconnnoconanonannnconnnonanoconna nora corona no nnnncrannnonnnos 9 3 1 2 Connecting to Personal Computer with USB Cable o cccoccccoonconcncconanononaconanoconnaconnnanono 10 2 APPLIC ATION EE al ects 10 INPUT DIAL DO td a dd 11 ADIAGNOSTIC OPERA TIO Sia A Aa 12 4 1 VEHICLE IDENTIFICATION ccccccccsesececccccccsececccccccesceececcecsuseececcecauseecececcecauseeeesececausteecec
Download Pdf Manuals
Related Search