3DQ -S1
Contents
1. 2 27 2 7 2 50 O AS SE 23 TOP VIEW SRO gt e O D 2 2 Ij 9 99 lt x i oo Leading Edga of The Blade AT oli page 3 User Manual Operation In Flying 1 Operation Process 1 1 Power the System Please confirm that your remote control is opened and aircraft is locked before power the aircraft Or aircraft will be alerted Red flash 1 2 Aircraft Unlock Check control direction and motor direction Wait for Green flash and you can unlock the aircraft Afer unlock LED change into yellow indicate that motor is accelerating Please don t move throttle stick during this process You can take off after LED change into White flash 1 3 Aircraft Lock After aircraft descend to the ground lock the aircraft motor slow down until stop LED change into Green flash 1 4 Change Flight Mode You can switch flightmode during the flight Recommends that keep your vehicle stable and it is located in safe altitude during switching flightmode In 3D Mode if your aircraft lose control during the flight you can switch into Attitude Mode Attitude Mode helps you stabilize the vehicle AltitudeHold Mode is easy to control you can take off directly in this Mode X Don t move it after power the vehicle until Green falsh 2 Flight Mode 2 1 Attitude Mode Aircraft can maintain attitude stabilization by itself in this Mode 2 2 3D Model You can operate aircraft flexibly in this Mode rolls inverted fligh2. Power below the threshold Yellow light always Processing the data Motor is accelerating White slow flash Normal flying condition ou can take off 1 When Red flash status please check remote control is opened and battery voltage 2 When Yellow light always please don t move throttle stick until white slow flash Preparing 1 Prepare Remote Control 1 1 Supported RC Our product support PPM PWM and S BUS receiver You can choose receiver type according to software At least 6 channel remote control 1 2 RC Setting You need to set the remote in Acro mode Then calibrate your remote control by using the software page User Manual 2 Before Flying 2 1 Check Control Direction yoy 2ANEPEN Forward Elevator Input Positive Pitch Positive Collective Input itch Yori annebaN THROTTLE_UP page 2 User Manual Negative Collective Input uoll4 2AREBON THROTTLE_DOWM Check Your Control Directions To Check The Rudder Direction Pay Close Attention To The Front ge ft Rotor Base Place The Br oll ctive Throttle Stick At The 3 4 4 A osition The Blades Wil S Position Pitch Pitch Sliders Will Move Up With The Collective At The 3 4 ick Position Place The Rudder Stick At Full Right Rudder Input osition Pitch On The Position Pitch Should Increase Pitch Sliders Shoule Move Higher 2 2 Check Motor Direction o D pD
3. 31 0 S1 User Manual 2015 7 AERITECHI CONTENTS Flight Control 1 Prepare Vehicle 1 1 Flight Control System Description 1 2 LED Status Instructions Preparing 1 Prepare Remote Control 1 1 Supported RC 1 2 RC Setting 2 Before Flying 2 1 Check Control Direction 2 2 Check Motor Direction Operation In Flying 1 Operation Process 1 1 Power the System 1 2 Aircraft Unlock 1 3 Aircraft Lock 1 4 Change Flight Mode 2 Flight Mode 2 1 Attitude Mode 2 2 3D Model 2 3 3D Mode2 2 4 AltitudeHold Mode Flight Control Connection Diagram Warning N N A A A A A A A RA O1 User Manual Please read Waring carefully at first Flight Control 1 Prepare Vehicle 1 1 Flight Control System Description 3DQ S1 Flight Control System is designed for Multi Rotor aircraft 1t has good handling performance and stability System modules Function MCU Board Core of system control all other modules IMU Perception aircraft attitude and position BEC Power the system LED Prompt the system status with light Tunning and Update Install 3DQ_ Flight Assistant software connect PC to BEC board with microUSB cabel You can tuning and update firmware according to the software Software download http www aeritech uav com 1 2 LED Status Instructions BEC LED Status Statu Note Red flash System error RC not calibrated or other error Green slow flash System is healthy You can operate normally Red slow flash Low power
4. t and so on This requires that you have a wealth of flight experience 2 3 3D Mode2 This Mode s curve is Smoother than 3D Model it is suitable for practing your 3D flying skills 2 4 AltitudeHold Mode Aircraft can maintain attitude and altitude by itself in this Mode When throttle stick in the middle position the aircraft will remain in current height Move stick up vehicle rise up Move stick down vehicle drop to the ground page 4 User Manual X You can switch into any Mode during the flight Recommends that keep your vehicle stable and it is located in safe altitude during switching flightmode Flight Control Connection Diagram i a ii r ost x 7 N F F N F F is Fi wd A i Lt 1 i h k ks M i 7 A muu En kS nm Bua w N 5 i i i 1 ie m Coppight 2014 2015 AERITECH use 5 EEE cEXT1 SERVO3 Ko k SERVO2 SERVO1 Warning This radio controlled model is not a toy It is a precision machine requring proper assembly and setup to avoid accidents It is the responsobolity of the owner to operate this product in a safe manner as itcan inflict serious injury and or death It is recommended that if you are in any doubt of your abilities seek assitance from experienced radio control helicopter modelers and associations As the manufacturer we assume no liability for the use of this product page 5
Download Pdf Manuals
Related Search