WMF...download manual - Corporate Coffee Solutions
Contents
1. The milk system consists of all in one spout milk hose milk nozzle m WMF special cleaner for milk foamers Order no 33 0683 6000 With the brushes included in the scope of delivery you can clean the narrow beverage spouts optimally WMF 1000 user manual Care Reassemble all parts of the all in one spout Place the milk hose on the all in one spout 10 Replace the all in one spout and push it into the lowest beverage position 11 12 m 42 WMF 1000 user manual Care Me Cleaning the brewing unit The brewing unit must cool off before cleaning k Switch off the coffee machine with the Off C button pull the mains connector Open the side doors on the right 1 k Press the handle marked PRESS firmly downwards and pull the brewing unit out of the coffee machine until it stops 2 x Tip the brewing unit slightly forwards and remove it upwards 3 Me Me amp Remove the tray for coffee grounds under the brewing unit and clean it with hot water 4 Use the multitoo from the accessories Unscrew the thread on the brewing unit head with the multitool anticlockwise until the scraper folds out forwards 5 Tip the insertion unit approx 45 degrees upwards until the brewing filter is visible 6 L multitool WMF 1000 us2. 4 2 Beverage settings Water volume Coffee strength Milk volume Sequence of the dispensing of milk and coffee Pre brew aroma development Menu elements only available for beverages with milk P Select aP Confirm f Care button fu Browse backwards Reduce value Browse forwards Increase value The new values are saved when you exit the program 26 WMF 1000 user manual Setting Me Dispensing test Each setting can be tested during setting 1 Water volume water volume 35m1 OK P change Example press the plus button until the water volume is increased to 37 ml water volume 37m OK P Test bev btn You can start a preparation test with the new values at any time Place an appropriate drinking vessel under the all in one spout Press the beverage button again k The beverage is dispensed k Confirm the setting by pressing the P button water volume 37m OK P change Coffee strength strength 86 5s OK P change Milk volume in seconds only beverages with milk milk volume 25 sec OK P change The volume dispensed depends on the milk lever posi tion the milk temperature and the milk nozzle selected Determine the desired volume with a dispensing test WMF 1000 user manual 7 Setting Sequence of the dispensing of milk and coffee The setting for the sequence of beverage dispensing is only e Fi
3. long lxcaf latte 16 WMF 1000 user manual Operation Me Example Prepare caf creme This description serves as an example for the prepara tion of all beverages All steps are carried out for the PA preparation of the other beverages according to the example Set height k If necessary adjust the height of the all in one spout A to the height of the drinking vessel Place an appropriate drinking vessel under the Cotreeipieparation usine th all in one spout manual insert k Press the beverage button for for caf cr me short See page 19 See overview of beverage buttons The beverage button pressed lights up white Dispensing milk and milk foam The display indicates See page 20 Depending on the setting the coffee beans are ground appropriately for the selected beverage The preparation occurs as specified in the beverage settings The beverage is prepared and dispensed into the drinking vessel underneath the spout The readiness display indicates Your selection pls 24 10 2006 08 15 Particularity of caf latte Select caf latte by pressing 1 x long see overview of beverage buttons P Select Before preparing caf latte P Confirm 1x caf latte fu Care Sutton Browse backwards Reduce value milk lever down H Browse forwards Increase value The new values are saved when you exit the program WMF 1000 user manual i7 Operation 3k Press the milk lever to the left of
4. 20 E Error list 50 Error messages 50 Errors without fault display 51 F Factory settings 30 Fault messages on the display 50 Faults 50 Faults with no display 52 Filling the coffee bean hopper 13 Filling the water tank 11 G General customer care programs 32 Glossary 10 H Hazard instructions 9 Hazards for the user 54 Hot water button 21 Insert the WMF tank filter 11 Introduction to settings 8 L Language 29 Lighting system 16 Maintenance 58 Manual cleaning 40 manual insert 19 Messages 46 Milk cold 47 Milk lever down 17 No warranty is provided 57 0 off 8 Off C button 8 Operating messages 48 Operating system 16 Other settings 31 Overview of beverage buttons 16 Overview of customer care 32 P Particularity of cafe latte 17 Parts of the machine 6 P button 8 Plus button 8 Positions of the all in one spout 22 Preparing caf cr me 17 62 WMF 1000 user manual lt Index Mf Preparing coffee beverages 16 Procedure for premium service 58 Program button 8 R Reading counters 30 Return delivery ticket 58 Rinse milk system 35 Rinse tank filter 38 S Safety systems 54 Scope of delivery 60 Second type of coffee 19 Sequence milk and coffee 28 Service ticket WMF 1000 58 Set the grinding degree 31 Setting 25 Settings basic settings 14 Setting the automatic switch on time 24 Setting up 11 Softener 60 Spare parts
5. 60 Stand by mode 24 Sterilising the milk system daily 46 Switching off 23 24 Switching on 23 Switching the coffee machine on 23 Symbols 8 T Taking apart the all in one spout 41 Tank filter 15 57 60 Technical data 60 Testing the water hardness 11 Time 14 29 Tips 48 Transport and disposal 59 U Unpacking 11 W Warm up rinse 34 Warranty period 57 Water filter 60 Water hardness 14 WMF replacement parts 57 WMF service hotline 58 WMF 1000 Service Center 58 WMF 1000 service ticket 58 WMF 1000 user manual 63 Your nearest WMF Customer Service Centre 2006 WMF Aktiengesellschaft Coffee Machines Division Postfach 1401 D 73309 Geislingen Steige Germany All rights reserved in particular duplication distribution and translation rights No part of this Manual may be reproduced in any form or processed duplicated or distributed using electronic systems without written consent Design and production typesetting and print presentation TecDoc GmbH Geislingen info tecdocgmbh de Printed in Germany Subject to technical modification 29 10 2006 ee WMF 1000
6. Gr week are ween S 39 6 5 Manual cleaning 40 Cleaning milk hose 1 0 0 cece ee teen me naama 40 Cleaning the milk systeM 0 0 0 ccc eee eee eee eens 41 Cleaning the brewing unit 6 0 cece eee 43 6 6 Cleaning in general 45 Cleaning the coffee grounds container 0 000 cece eee 45 Cleaning the water tank 0 ccc cee eee eee nee eens 45 Cleaning the drip try and drip tray grid 0 cece eee eee 45 Cleaning the bean hopper 0 0 ccc cece eee eee eees 45 Chapter 7 HACCP cleaning schedule WMF 1000 user manual W Table of Contents Mf Chapter 8 Messages and tips 8 1 Operating messages 48 Empty coffee grounds container 0 cee eee 48 Refilltwater tank es dc0c soeed ae tto Mea bee n Tina Meee 48 Empty Grip tray nic id dct ae Sd ae Saas Sead dad Sawa rarai Ges 48 Bean hopper is empty 0 ccc e eee ee ee ee eee tenes 48 INS rtCOff grounds zs 2 nce ee ae renas Fe eG Rha CEE ae See EES 49 Change tank filter ccs cces areas n rran ena Gees bo E aaa EN 49 Side door Open se ec sc terad kisas Pewee eee taad See Ead 49 LOWErSPOUl cose eae ieeed ieee ioeed a eee EE Soe endo ees 49 8 2 Error messages and faults 50 Fault messages on the display 0 0 0 cece eee eee eens 50 8 3 Problems with no fault display 52 Chapter 9 Safety 9 1 Hazards for the user 54 9 2 Hazards for the coffee machine 55 9 3 Responsibilities of the operator 56 9 4 Warranty claims 56 No warranty i
7. P button The machine rinses and then goes into Timer operation The display indicates the switch on time set the current time and the date The machine switches on automati cally at the set time Display timer operation timer 06 30 14 04 2006 08 15 Manual switch on for timer operation Press the Off C button short In timer operation the machine switches on again imme diately before the automatic set time Manual switch off for timer operation Press the Off C button for approx 2 seconds The machine switches off and the timer is no longer active Set automatic switch on time to active see chapter 4 settings gt basic settings gt automatic switch on time If the machine is not operated within an hour it switches off again and returns to timer operation The display of time and date can be hidden See chapter 4 settings gt basic settings 24 WMF 1000 user manual Me Setting Chapter 4 Setting About the settings Press the P button for approx 2 seconds select program browse Chapter 4 1 Chapter 4 2 Chapter 4 3 Chapter 4 4 cup size OK P browse cup size select beverage cup volume 100 OK P Test bev btn beverage settings OK P browse beverage settings select beverage water volume 35m1 OK P change strength 100 4s OK P change milk volume 25sec OK P change sequ coffee milk OK P change pre brew
8. Select the beverage with the beverage buttons This procedure can be cancelled with the Off C button e Always use ground coffee for the manual insert max 15 g per preparation e The coffee machine gets soiled inside if too much ground coffee is put in at once e Do not use water soluble freeze dried instant coffee e Each brewing cycle via the manual insert is measured separately e Coffee ground too fine can cause faults A 7 See Chapter 6 Customer Care gt Cleaning the brewing uni WMF 1000 user manual 19 Operation 3 3 Dispense milk and milk foam At the touch of a button the WMF 1000 dispenses hot milk and milk foam press short press and hold 1 cup milk Milk milk foam on request Milk milk foam is dispensed as long as the button is pressed Dispensing milk milk lever down Place an appropriate drinking vessel under the all in one spout Press the milk button once short 1x cup milk milk lever down Put the milk lever in the milk position Confirm the beverage selection with the milk button Milk is dispensed Afterwards press the milk lever upwards again Confirm with the P button Another press of the milk button ends the dispensing prematurely Dispensing milk foam milk lever up lt Place an appropriate drinking vessel under the all in one spout Press the milk button until the desired quantity has been dispensed EA Set cup size see Chapter 4 Set
9. a coffee system rinse This warms up all the pipes amp Place a container for the rinse water under the all in one spout approx 200 ml A coffee system rinse starts The coffee system rinse lasts approx 40 seconds after this the machine is ready to operate Your selection pls 24 10 2006 08 15 Va Rinse filter Follow the display texts see also change filter in Chapter 6 Customer Care A Cup size and beverage settings see Chapter 4 Settings P Select P Confirm Care button Browse backwards 5 Reduce value Browse forwards Increase value The new values are saved when you exit the program WMF 1000 user manual 15 Operation Chapter 3 Operation Operation and lighting concept Preparing coffee beverages vie Example preparing caf cr me Dispensing milk and milk foam a Sen instructions to operate tne Te WMF 1000 safely se See Chapter 9 Safet Control buttons y Functional parts 3 1 Operating and Lighting concept The lighting system helps you with navigation Only the buttons which can be operated in the current situation are lighted 3 2 Preparation of coffee beverages The WMF 1000 has four beverage buttons each of which has two functions Overview of beverage buttons e For Ist level beverages press short e For 2nd level beverages press long caf creme short latte macchiato short short espresso long 2xespresso short cappuccino
10. cleaning WMF 1000 Return delivery ticket WMF 1000 WMF carbonate hardness test with manual Cleaning agents cleaning solutions and descaling agents are irritants for people textiles and for the plastic parts of the machine Absolutely heed the safety instructions on the package WMF 1000 user manual 61 Index Index A Accessories and spare parts 59 Adjusting the height 22 All in One spout 22 Assembling the milk hose 12 Automatic switch on time 24 29 Basic settings 29 Bean hopper 7 Beverage buttons 16 Beverage preparation in general 21 Beverage settings 26 Brewing temperature 30 Browse 8 Browse forwards with plus 8 C Call customer care programs 33 Cancel beverage preparation 21 Care program general 32 Care programs 34 Change tank filter 38 Cleaning in general 45 Cleaning program 36 Cleaning the bean hopper 45 Cleaning the brewing unit 43 Cleaning the coffee grounds container 45 Cleaning the drip tray and drip tray grid 45 Cleaning the machine 36 Cleaning the milk system 41 Cleaning the water tank 45 Coffee strength for the next beverage 18 Coffee system rinse 23 34 Commissioning 11 Commissioning program 13 Connecting the milk hose 13 Control buttons 23 Cup size 26 Cup volume 26 Customer care 32 D Date 14 29 Date Time 29 Delete all counters 30 Deliming coffee machine 39 Dispensing hot water 21 Dispensing milk 20 Dispensing milk foam
11. for the next beverage Plus button Aroma button e Browse forwards with plus e Increase coffee strength for the next beverage 1 3 Before starting Read this user manual before starting to prepare coffee Only then can you operate all functions and the machine safely and spoil yourself with a wonderful coffee beverage Additional components of the user manual e Brief manual for beverage dispensing care WMF 1000 user manual Introduction and General Information Mf 1 4 User manual signs and symbols Hazard instructions Attention Risk to machine Attention Hot liquid Attention Danger of electric shock Tips and hints 1 Hint 2 Note about the figure gt gt e A Attention Risk to user Attention Hot surface Attention Danger of hand injuries Cross reference Please always heed the safety instructions in Chapter 9 A WMF 1000 user manual Introduction and General Information 1 5 Displaying the readiness state The descriptions in the user manual always assume that the coffee machine is ready to operate your selection pls 24 10 2006 08 15 1 6 Glossary Term Meaning e Listings selection options ok Individual activities individual steps Italics Description of coffee machine state and or explanations of steps carried out automatically Beverage dispensing Dispensing of coffee hot water milk or milk foam Main tap Water on off valve a
12. however it must be carried out within the next 50 brew cycles Otherwise beverage dispensing will be blocked The blocking will be cleared after a descaling 6 5 Manual cleaning Cleaning milk hose The milk hose must be cleaned thoroughly at least once a day e After switching off the machine take the milk hose out of the milk and wipe with a clean damp cloth Place the parts of the hose that have come into contact with milk in a container with cleanser overnight Wipe off the milk hose with a clean damp cloth Carry out a milk system rinse I A See Call customer care programs without request Cleaning solution e 5 ml special cleaner for milk foamers e 200 ml hand hot water Milk system rinse See Care programs 40 WMF 1000 user manual Care Me Cleaning the milk system All parts of the milk system must be cleaned thoroughly at least once a week Remove the water tank from the coffee machine 1 k Remove the hose from the milk container and the guide 2 3 k Press the all in one spout firmly together and at the same time pull it downwards 4 5 6 st l 7 lt Taking apart the all in one spout 7 Mix 5 ml WMF special cleaner for milk foamers in a container with 200 ml lukewarm water water 9 Place all parts of the milk system 8 in the cleaning solution for 5 hours or overnight Then rinse all parts thoroughly with running warm
13. spout Mo Ma Me connect hose Start care button lt Wipe off the outside of the milk hose with a clean damp cloth x Place the milk hose with the milk nozzle on the hot water spout and turn it clockwise to the stop k Start the rinse with the care button The coffee machine s milk system is rinsed with hot water Hot rinse water is emptied through the all in one spout After a successful rinse the following display appears lower spout into beverage position Turn the milk hose anticlockwise disconnecting it from the hot water spout Duration of milk system rinse approx 30 seconds Place the milk hose on the hot water spout and turn it clockwise to the stop WMF 1000 user manual 35 Care After the rinse some hot water remains in the milk hose Hold the open end of the milk hose over the drip tray so i that the remaining rinse water can run out Push the all in one spout downwards If the all in one spout is already in the beverage position the readiness state display appears your selection pls 08 15 14 04 2006 If products with milk were prepared after 20 minutes or at the latest when switching off the machine automati cally requests a milk system rinse Confirm and perform the milk system rinse with the P and button The milk rinse can be put off with the Off C button Cleaning the machine Cleaning program clean machine OK P brwse Care bt Confirm the machine cleanin
14. the all in one spout downwards Confirm that the milk lever is pressed downwards by Pi pressing the lighted beverage button Beverage preparation begins See Preparing milk and milk foam Page 20 After preparing caf latte milk lever up Press the milk lever upwards sk Confirm with the button P Setting coffee strength for the next beverage Before each coffee preparation you can decide how strong you want the next coffee beverage to be e Mild approximately 15 weaker than the saved setting e Normal corresponds to your setting e Strong approximately 15 stronger than the saved setting 3 lt Place an appropriate drinking vessel under the all in one spout Set the desired coffee strength with the and buttons Select the beverage The beverage button selected lights up and the beverage name is indicated on the display The selected beverage is prepared Pa See preparing beverage 18 WMF 1000 user manual Operation Me Coffee preparation using the manual insert In addition to the coffee bean hopper there is a manual insert for a second type of coffee so that for example you can prepare decaffeinated coffee Place an appropriate drinking vessel under the all in one spout k Open the cover of the manual insert The display instructs insert coff grounds select beverage x Place the ground coffee for one brewing cycle in the manual insert x Close the cover
15. the float red plastic part in the guide Replace the water tank Heavy calcium deposits can be removed with the WMF descaling agent After descaling rinse the water tank very thoroughly in order to remove all the descaling debris Cleaning the drip tray and drip tray grid Empty the drip tray and drip tray grid and rinse with water x Insert the drip tray and drip tray grid Cleaning the bean hopper x Switch off the machine pull the mains connector Wipe out the bean hopper with a dry lint free cloth WMF 1000 user manual 45 Care Chapter 7 HACCP Cleaning Schedule You are required by law to ensure that your customers are subjected to no health risks as a consequence of consuming food substances you serve An HACCP Schedule Hazard Analysis Critical Control Points for risk identification and assessment is required You should carry out a risk analysis on your premises The aim of the analysis is to recognize and preempt food hygiene hazard points For this monitoring and if necessary testing procedures must be specified and implemented With correct installation service care and cleaning WMF coffee machines meet the abovementioned require ments If the care and cleaning of the coffee machine is not carried out properly the dispensing of milk bever ages becomes a hazard with respect to food hygiene Please observe the following points in order to comply with the HACCP schedule Sterilisi
16. to the electronics waste disposal law WEEE EC directive and it may not be disposed of as domestic waste 9 4 Warranty claims During the warranty period of 12 months from date of purchase the purchaser has statutory warranty entitlement a See Chapter 10 Maintenance For disposal please consult WMF customer service 56 WMF 1000 user manual Safety Me WMF shall always have the opportunity to rectify faults within an appropriate period Claims above and beyond these especially damage claims as a result of consequential damage are to the extent that is legally permissible excluded Material defects shall be reported to WMF immediately and in writing Warranty period 12 months No warranty is provided e For all parts subject to natural wear and tear These include among other things seals and the brewing unit e For defects due to the effect of the elements deposit of boiler scale chemical electrochemical or electrical effects unless attributable to fault on the part of WMF e lf atank filter is not used even though the water hard ness where the machine is used requires the use of a tank filter and this causes defects e For defects which occur as a result of failure to follow handling instructions service and care of the unit e g user manuals and servicing instructions e For defects which occur as the result of failure to use J original WMF replacement parts or incorrect assembly by the
17. water comes out No hot water dispensing Remove tank filter dirt trap from tank try again Brewing unit stopped up Remove brewing unit clean manually insert and carry out cleaning program Clean brewing unit see Chapter 6 Customer Care gt Brewing unit If the error occurs sporadically Set grinding degree coarser x Switch off pre brew EEPROM Error Switch machine on off If the error repeats the fault must be eliminated by the WMF 1000 Service Center See chapter WMF 1000 Service Center Motor driver error Switch machine on off If the error repeats the fault must be eliminated by the WMF 1000 Service Center Grinder blocked The grinders are blocked by foreign bodies To eliminate see section Manual cleaning Clean bean hopper switch off machine turn grinders clockwise with the multitool in order to be able to remove foreign bodies See Chapter 5 Other Settings Grinding degree too fine Set grinding degree coarser Temperature sensor steam Temperature sensor water Switch off coffee machine allow to cool and switch on again If the error repeats the fault must be eliminated by the WMF 1000 Service Center Timeout level Air in the system possibly associated with loud pump noise x Check whether the water tank is pushed in completely amp Take milk hose out of the milk container and press the milk foam button If hot water comes out instead of s
18. which are not past their sell by date Cleaning steps 1 Execute the cleaning program See brief manual Daily cleaning 2 Clean the milk hose See brief manual Daily cleaning 3 Exchange the all in one spout after 4 hours operating time absolutely necessary with low flow rate and unrefrigerated milk Year 4 General machine cleaning Cleaning steps Cleaning steps 5 Time Signature 5 Time Signature HEZ 3 4 3 1 17 2 18 3 19 4 20 5 ai 6 22 7 23 8 24 9 25 10 26 11 27 12 28 13 29 1 30 15 31 16 WMF 1000 user manual 47 HACCP cleaning schedule Chapter 8 Messages and tips 8 1 Operating messages Empty coffee grounds container empty grounds cont beverage sel locked grounds cont missing Refill water tank refill water tank beverage sel locked refill water tank Empty drip tray empty drip tray beverage sel locked drip tray missing Bean hopper is empty refill beans confirm beverage The coffee grounds container is full Remove the coffee grounds container empty it and rinse it with water Replace the coffee grounds container Confirm with the P button The water tank is nearly empty Remove the water tank and fill it Replace the water tank The drip tray must be emptied Remo
19. 0 user manual Commissioning Me 2 4 Connect the milk hose to the milk Place the refrigerated milk directly to the right of the machine Place the milk hose with the milk nozzle on it into the milk container The hose end with the milk nozzle should reach to the bottom of the milk container Milk is a very delicate food When handling milk always heed hygiene Heed the HACCP cleaning shedule See Chapter 7 2 5 Fill the coffee bean hopper amp Open the cover towards the back Fill coffee beans max 320 g can be expanded to 500 g with optional attachable coffee bean hopper x Close the cover Heed that no foreign bodies land in the coffee bean hopper Such foreign bodies can damage the grinders of the coffee mill This damage is excluded from the warranty 2 6 Commissioning program Press the Off C button The commissioning program starts language english OK P change Set the desired language for the display guidance here The commissioning program uses the display to lead you step by step through the commissioning Follow the display texts Only provide milk if necessary A WMF 1000 user manual 13 Commissioning initial setting up Rae of your WMF 1000 The set values can be changed The machine is switched on the commissioning program in the Settings program after leads you through the basic settings commissioning Basic Settings Pa Set the desired va
20. USER MANUAL COFFEE MACHINE WMF 1000 ENGLISH 0 40 WMF1000 33 0915 6010 2006 08 Introduction and General Information Congratulations on the purchase of your WMF coffee machine You will be impressed by the machine s technical design its long service life and economical operation and especially by the quality of the coffee it produces The WMF 1000 pro coffee machine is a fully automatic single cup coffee machine for espresso caf cr me cappuccino caf latte latte macchiato hot milk foamed milk and hot water Each beverage is freshly brewed at the press of a button which guarantees a high quality beverage User guidance for the coffee machine is provided on the display Keep this user manual near the coffee machine so that you and your operating staff have the right information handy and can take the correct action s in the event of any technical problems The coffee machine is designed to prepare up to 10 000 coffee beverages per year After every 10 000 beverages service by the WMF service centre is required The machine must be cleaned and descaled regularly Please absolutely head the Chapter 2 of the manual Commissioning gt Setting gt Water hardness and to make the necessary settings A A Please read the user manual prior to using the coffee machine Make the user manual available to your staff Important Chapter 1 Pre setting Heed signs and symbols in the user manual He
21. achine to frost e This coffee machine is not for use out of doors do not spray the machine with water The maximum rela tive humidity should not exceed 80 no dewing e Do not use water hose steam jets steam cleaners or the like to clean the device e The device must be set on a flat level and secure surface 9 3 Responsibilities of the operator The coffee machine meets the requirements of the EC low voltage directive LVD and the EMC directive and bears the CE mark The pressure containers are not subject to the EC PED Directive see Article 1 Paragraph 3 6 as they conform with Article 3 Paragraph 3 of the PED The hot water steam generator is neither notifiable nor liable to approval Calculations confirm to AD 2000 Each machine is subjected to a pressure test For countries outside the EC the respectively valid national rules apply The operator of such equipment must ensure regular servicing by WMF Customer Service technicians their agents or other authorised persons and check the safety devices The operator must ensure that the electrical equipment and operating facilities are in a fit state e g in accordance with BGV A3 In order to ensure the operational safety of your coffee machine replacement of safety valves after 2 years is advised and boiler replacement after no more than 6 years These measures are routinely carried out in the course of mainte nance by WMF Customer Service This machine is subject
22. ation 0 0 0 0 aana 24 Chapter 4 Setting 4 1 Cup size Cup volumes 26 DISPENSE TEST amp 2 3 Sealers Grane eho e raare ro hea wo hanes wee amass raed 26 4 2 Beverage settings 26 DISHENSING TEST aie Since dg raw dine beg omer Sh cw ex dane danas are 27 water VOIUME 0 eee eee nent ee tenn eaee 27 Coffee SENSE eri ccacaretdmrscaret dy men ards waists waters wnntare a nE dE 27 MINK VOMUMNG cs eeoa ateucaet obec aa E E et arse tn rset 27 Sequence of the dispensing of milk and coffee 0000 28 PHONDIOW aeeie na mnei atacand Mem tees EE eE aE E ance 28 DISPENSING testni eri era Sex era E EL aE anni arate Greek 28 4 3 Basic settings 29 Date MIMO 25 iceri energeia era ee eaae weg dna eae anr EL Aan 29 Automatic switch on time sasaaa nauau ea 29 SWitehoff Mesero knatiersSoaratere s nne a ene aE a NNE EE ELE 29 Brewing temperature 0 0 0 0 ccc een eens 30 FACtOry SEINES tees Sicaeetd Anant Sra geet apd aAa eee aoa weet on aoe red 30 4 4 Reading counters 30 Chapter 5 Other settings 5 1 Set the grinding degree 3l Chapter 6 care 6 1 General customer care programs 32 6 2 Overview of customer care 33 6 3 Calling Customer care programs 34 6 4 Customer care programs 34 Warm up rinse Coffee system rinse n nananana 34 Rinse MIK SYSTEM aA ga re eE PANE E 35 Cleaning the machine Cleaning program 000e eee eens 36 Change TAM TNH coo terra descr e aE EELEE EES 38 DESC Birt itecbind ten ek Sea ted bes erar e
23. ed Chapter 9 Safety A In the event of failure to comply with cleaning and maintenance information see Maintenance chapter no liability is accepted for any resultant damage Similarly in that event all guarantee warranty obligations cease to apply WMF 1000 user manual W Table of Contents Mf Chapter 1 Introduction and General Information 1 1 Parts of the machine 6 1 2 Overview of control buttons 8 Off C DUTTOM s iii cena ete anre aren aa dee a Pew eS 8 Program button P button 2 0 0 ccc eee 8 Minus button Care button Aroma button 8 Plus button Aroma button n anaana anaana anaana 8 1 3 Before starting 8 1 4 User manual signs and symbols 9 Hazard InsStructlonSs 2i c0c nenea deed Maes Ea bees 9 TIPSANG MINS ae And oid decd deka das ached ake ata 9 1 5 Displaying the readiness state 10 1 6 Glossary 10 Chapter 2 Commissioning 2 1 Unpacking and Setting up 11 2 2 Testing the water hardness 11 2 3 Preparing the water tank 11 Insert the WMF tank filter 0 nananana 11 Assembling the milk hose 0 0 0 cette eee 12 Rillithe Water tanks eni a8 Sikr ada dco ad deat Mags E a A EE Aad AL 12 2 4 Connecting the milk hose to the milk 13 2 5 Filling the coffee bean hopper 13 2 7 Commissioning program 13 Basic SQuing Swiad ck ech dcddiog ded ouid det pad pe aaen te 8 14 TWIGS se hatte anes anc en ane ee nee ane ene 14 Dalen so erate ee aes oe ert en tee mem hen ee ae 14 Water ha
24. er manual 43 Care Clean the brewing filter under running water or with a cloth 7 Rinse the brewing unit under running water 7 Never clean the brewing unit in a dishwasher and never use any cleaner additives Dry the brewing unit with a cloth Allow to dry completely before replacing in the coffee machine lt Remove coffee grounds in the chute with a vacuum cleaner 8 Screw the brewing unit back clockwise using the multitool Replace the tray for coffee grounds 9 ie EA Reinstall the dry brewing unit Insert the brewing unit and push it firmly back into the housing until the handle marked PRESS snaps in clearly and is level again Close the side doors If the brewing unit cannot be inserted completely Turn thread on the brewing unit head slightly to the left or right with the multitool until the brewing unit slides into the guide Never use force 44 WMF 1000 user manual Care Me 6 6 Cleaning in general Never clean the water tank drip tray or the coffee grounds container in the dishwasher Cleaning the coffee grounds container Empty the coffee grounds container and rinse with water Cleaning the water tank Empty the water tank Remove the filter cartridge and the adapter if a filter is used x Remove debris in the tank and on the adapter with a scrub brush Rinse the water tank with water amp Check smooth running of
25. er the machine is heated up there is a coffee system rinse This rinse warms up all pipes The coffee system rinse lasts approx 40 seconds after this the machine is ready to operate Your selection pls 24 10 2006 08 15 Switching off k Place a container for the rinse water under the all in one spout approx 200 ml k Press the Off C button for approx 2 seconds If beverages with milk such as caf latte were prepared Pa then you will be asked to perform a milk system rinse A coffee system rinse begins after that Follow the display Ki system rinse texts The machine switches off Chapter 6 Customer Care gt Care programs When switching the machine on and off an coffee system rinse starts automatically The coffee system rinse also starts when the machine is switched on and off automatically in timer operation Empty the drip tray regularly the rinse water will be emptied into the drip tray by the all in one spout approx 200 ml You can place a container under the all in one spout and catch the rinse water WMF 1000 user manual 23 Operation 3 9 Switching on and off in timer operation Setting the automatic switch on time To use the timer the basic setting Automatic switch on time must first be set to active To switch off the machine in timer operation press the Off C button short timer 06 30 OK P change Set the switch on time with the and J buttons Confirm with the
26. f and then on again after a few seconds Repeat the process which caused the fault In many cases this eliminates the fault and you can continue working If this is not successful Search in the error list for the error message and follow the instructions If this is not successful or the error displayed is not listed please call the WMF service hotline Some messages lead to blocking of individual functions You will notice this by the fact that the beverage button light goes out The beverage buttons which are still illuminated can continue to be served Fault messages on the display Error message Action Use brewer Brewer is not used Use brewer Brewer end switch Brewer unit not inserted correctly Use brewing unit correctly Brewing unit stiff Remove brewer open brewing chamber with multitool apply a thin layer of the grease from the accessories kit to the red seal ring Flow fault 3k Check to make sure that float in the water tank runs water tank is empty smoothly and fill water tank See Chapter 6 Customer Care gt Water tank k Bleed machine Dispense hot water until a constant stream of water comes out 50 WMF 1000 user manual Ww Messages and tips Mf Flow fault water tank is full Air in the system possibly associated with loud pump noise x Check whether the water tank is pushed in completely Bleed machine Dispense hot water until a constant stream of
27. g cleaning tablets and descaling agent please heed the protective measures on the packaging The cleaning tablets and descaling agent are an irritant Only insert the cleaning tablet and the solution with descaling agent after requested to do so on the display Irritation and scald hazard Never reach under the spouts during the cleaning descaling During the cleaning descaling cleaning liquid descaling solution flows out of the all in one spout 9 2 Hazards for the coffee machine Please heed the following instructions in order to avoid technical problems with and damage to the coffee machine e With water with a carbonate hardness in excess of 5 dKH a WMF tank filter should be used otherwise the coffee machine can be damaged due to build up of scale e For insurance reasons always ensure that at the end of operation the main electric switch is switched off or the mains connector is pulled e We recommend damage prevention measures Installation of smoke detectors e After lengthy periods out of use cleaning program must be carried out at least twice before comis sioning again e With a tank filter the filter must also be rinsed or changed if necessary before commissioning again A A Attention Health Hazard Attention Health Hazard A A Attention Danger of irritation or scalding near outlet A See brief manual Daily cleaning WMF 1000 user manual 59 Safety e Do not expose the coffee m
28. g with the P button The individual steps appear on the display on request Start the care program without empty drip tray request See Chapter 6 3 Duration of cleaning program refill water tank approx 5 minutes place 31 container under coffee outlet Place an appropriate container min 3 litres under the all in one spout 36 WMF 1000 user manual Care Me insert tablet into manual insert Add a cleaning tablet together with the yellow sponge Nienie eberednaiis oF cleaning tablet Consists O and close the cover a white tablet and a yellow start care button sponge Press the care button The cleaning program starts A minute countdown indicates how long until the descaling will finish cleaning in progress Remaining time 5 min After 5 minutes the machine cleaning ends The display calls for a manual milk system cleaning After the first beverage dispensing this display disappears After 230 brewing cycles or 7 days the request for a machine cleaning appears on the display The cleaning 1 can be put off with the Off C button Cleaning must take place within the next 50 brew cycles however at the latest on the next day Otherwise beverage dispensing will be blocked The blocking will be cleared after a cleaning WMF 1000 user manual a7 Care Change tank filter filter change OK P brwse Care Confirm with the P button remove water tank Remove
29. gs 5 1 Set the grinding degree Changing the type of coffee can require resetting the grinding degree Use the included mulititool Place the multitool into the grinding degree adjust ment on the left side of the coffee machine Release coffee dispenser and wait until grinder starts up e Grinding should be finer turn clockwise e Grinding should be coarser turn anticlockwise e The grinding degree may only be set when the grinder is running e Never adjust more than one rotation at a time e Do not overwind the stop with force The factory setting of the grinding degree is designed for the qualities of average coffee beans When adjusting 1 there are the following limits Grinding degree too fine The dispensing stream is interrupted and or flow fault gt the ground coffee stops up the brewing filter Grinding degree too coarse Especially for espresso the coffee flows too fast the cr me is too light and has too little body the aroma is flat Correct setting Check your setting by preparing a double shot of espresso If the dispensing stream is interrupted here or if the display indicates a flow fault set the grinding degree at least one turn coarser again WMF 1000 user manual 31 Care Chapter 6 Care The care of your WMF 1000 is especially important The display notifies you as soon as the WMF 1000 must be rinsed cleaned or descaled 6 1 Care program general When switching t
30. he machine on and off an automatic coffee system rinse starts automatically This requires that there always be sufficient water in the water tank 200 ml per rinse The rinse water is caught in the drip tray Empty the drip tray regularly or place a container min 200 ml under the all in one spout during the rinse After each brewing cycle in the heating up phase and during the care programs so called release water runs into the drip tray This rinses any remaining coffee from the pipes This is a completely normal procedure and not an error in the coffee machine 32 WMF 1000 user manual Care Me 6 2 Overview of customer care Care Daily Weekly Regularly On request Optional Care programs Coffee system rinse X Milk system rinse X Coffee machine cleaning Filter change Manual cleaning X Brewing unit X Milk system x Milk container Drip tray Drip tray grid Housing Water tank zs less es es es es es Ground coffee hopper WMF assumes no liability for damage due to lack of cleaning or descaling or due to the use of other cleaning or descaling agents than those provided by WMF All guarantee and warranty claims are extinguished Cleaning and descaling agents are irritants and during execution of the programs they become very hot Avoid any contact with these liquids The plastic parts of the coffee mach
31. in one spout dispenses coffee and milk foam simultaneously and it can be set steplessly so that you can place anything from an espresso cup to a latte macchiato glass beneath it The adjustment height ranges from 75 135 mm Adjusting the height Hold the all in one spout between your thumb and forefinger and press the right adjustment lever towards the spout lt Move the all in one spout to the desired height lt Release the adjustment lever vy y Positions of the all in one spout The uppermost position of the all in one spout is reserved for the milk system rinse e Uppermost position milk system rinse spout clicks into position e Other positions beverage dispensing variable height If the all in one spout is still in the milk system rinse posi tion after a milk system rinse the display reports lower spout into beverage position Put the all in one spout in a beverage dispensing position As soon as the all in one spout is back in a beverage dispensing position the message disappears and the readiness display appears 22 WMF 1000 user manual Operation Mf 3 8 Switching on and off Switching on Press the Off C button The greeting display appears then the coffee machine heats up WELCOME WMF 1000 Time from switching on until heating u Daes readiness state approx 2 min x Place a container for the rinse water under the all in one spout approx 200 ml Aft
32. ine may not come into contact with the descaling agent Heed the instructions on the packaging and in Chapter 9 Safety a Automatic start when switching the machine on and off see Customer care programs see Manual cleaning gt WMF 1000 user manual 33 Care 6 3 Calling care programs To select the care programs without a previous request on the display Press the P button select care program brwse care button Use the care button to browse to the desired program Select the displayed program with the P button 6 4 Care programs Warm up rinse Coffee system rinse rinse coffee system OK P brwse care bt Place an appropriate container under the all in one spout Issue the request with the P button Start the rinse with the care button The pipes of the coffee machine are rinsed with hot water Hot rinse water is emptied through the all in one spout After the rinse the readiness state display appears your selection pls 08 15 14 04 2006 34 WMF 1000 user manual Care Me Rinse milk system rinse milksystem OK P brwse care bt Select the displayed program with the P button The display reports the individual activities that must be done before the rinse milk lever up move spout up max k Check if the milk lever is up If not put it up now lt Push the all in one spout to the uppermost position lt Place an appropriate container under the all in one
33. lues with the and buttons Use the P button to confirm the values and inputs After confirmation the program jumps to the next point of the Chapter 4 Settings settings When exiting the program the new values are saved Time P Select time hh mm ss P Confirm OK P change Care button fu Set the current time here g Browse backwards Format hh hour two digits mm minute two digits Reduce value ss seconds two digits Browse forwards Increase value Date The new values are saved when you exit the program date dd mm yyyy OK P change Set the current date here dd day two digit mm month two digit yyyy year four digit Water hardness water hardn 13 16 OK P change Set the result of the carbonate hardness test here Pa Carbonate hardness test See included accessories 14 WMF 1000 user manual W Commissioning Mf Tank filter water filter no OK P change Enter here whether you are using a tank filter recom mended with water hardness 5 dKH and higher If water filter is set then the filter should be rinsed now place 31 container under h w spout Set a container with approx 3 litres capacity under the hot water spout When rinsing the filter you will hear unusual noises This is normal The noises will end during the filter rinse The machine now heats up heating up After the machine is heated up there is
34. machine should switch off automatically Switch off time O min gt Switch off time deactivated A For a description of the other basic settings see Chapter 2 Commissioning A Setting the switch on time See Chapter 3 9 switching on and off in timer operation Attention If timer operation is activated the machine switches on again at the set switch on time a WMF 1000 user manual 29 Setting Brewing temperature Brewing temp 92 C OK P change You can set the temperature of the brewing water here The default is 92 C Factory settings factory sett No Attention OK P change All individual settings are lost if ou reset to the factory settings You can set all values back to the factory settings here y If you select yes all basic settings and all beverage settings are reset to the factory settings 4 4 Read counters counters OK P brwse You can display the quantities of beverages prepared here Use the plus button to browse through the individual beverages Example of espresso Espresso 269 OKE R TDHS Eng An As soon as all beverages have been displayed or the Off C button has been pressed the message appears reset all counters No Yes Keep the counters press the minus button Delete all counters k press the plus button 30 WMF 1000 user manual W Other settings Mf Chapter 5 Other settin
35. ng the milk system e Adhere to the cleaning instructions for the milk system in the brief manual for daily cleaning This will ensure that your system contains minimal germs at commencement of operation When you commence operation always begin with freshly opened pre refrigerated milk e Originally packaged UHT milk is normally free of harmful germs Always open a new pre refrigerated package at commencement of operation e Ensure absolute cleanliness on opening the milk package Dirty hands or implements when opening may introduce germs Ordinance concerning food hygiene From 5 August 1997 Use our HACCP cleaning schedule to monitor the regular cleaning Recommendation Use only UhT milk with a 1 5 fat content 46 WMF 1000 user manual Me Keep the milk cold The milk should be 6 8 C when e Always have a new pre refrigerated milk package operation commences hand Depending on the setting y one litre of milk produces e lf a pre refrigerated freshly opened milk package approx 20 cappuccinos is consumed within 3 hours maximum refrigeration WME AG offers various cooling during operation may not be necessary possibilities e f milk consumption is lower then the pre refrigerated milk must be cooled during operation HACCP Cleaning Schedule Month Use only refrigerated UHT milk as otherwise health risks due to microbacteria cannot be excluded For Choc and Topping use only products
36. ngle valve Carbonate hardness Indication in dKH Water hardness is an indicator of calcium dissolved in the water Milk system All in one spout milk nozzle and milk hose O rings Seals Pre infusion Prior to the brewing cycle coffee is briefly infused to ensure a more intensive release of its aromatic substances Press Automatic pressing of coffee grounds prior to brewing cycle Range For example litre capacity of the tank filter Rinsing Intermediate cleansing 10 WMF 1000 user manual Commissioning Me Chapter 2 Commissioning 2 1 Unpacking and Setting up 1 Unpack coffee machine and set up on a stable hori zontal support k Check the coffee machine for possible transport damage Plug the connector into a grounded outlet Assemble bean hopper attachment Insert drip tray and drip tray grid 2 2 Test the water hardness Briefly dip carbon hardness test strip into water approx 1 second One minute later read the degree of hardness on the colour scale of the test strip package The water hardness is set during commissioning 2 3 Prepare the water tank Remove the water tank from the coffee machine amp Remove all accessories from the water tank k Rinse the water tank thoroughly with tap water Do not put the water tank back into the machine yet The milk hose must be assembled first Insert the WMF tank filter The WMF tank filter ensures the best coffee q
37. old filter Insert new filter lt Remove the old filter lt Insert a new filter lt Refill water tank va lt After the change confirm with the P button 3 Change tank filter Filter rinse See Chapter 2 Commissioning place 31 container under h w spout MM A lt Place a 3 litre container under the hot water spout lt Start the filter rinse with the care button 3 y Filter rinse running Remaining time 4 min When rinsing the filter you will hear unusual noises This is normal The noises will end during the filter rinse During further operation everything will sound normal again After the rinse the readiness state display appears your selection pls 08 15 14 04 2006 but after 3 months at the latest the request appears to change the tank filter The filter change can be put off with the Off C button Depending on the water hardness and the water flow I 38 WMF 1000 user manual Care Me Descaling descale machine OK P brwse Care x Press the care button Empty the drip tray k Pull the water tank out of the machine towards the front Remove the filter cartridge if a tank filter is used important Empty a whole bottle of WMF liquid descaling agent 750 ml into the water tank lt Fill the water tank with water Remove the all in one spout Place an appropriate container min 3 litres under the all in one spout lt Place another container min 1 litre unde
38. on OK P change P Select P Confirm ru Care button Browse backwards 5 Reduce value Browse forwards Increase value The new values are saved when you exit the program basic settings OK P browse language english OK P change time hh mm ss OK P change date dd mm yyyy OK P change date time on OK P change switch on time on OK P change sw off time 60min OK P change water hardn 13 16 OK P change water filter OK P change brewing temp OK P change factory sett OK P change counters OK P browse espresso 269 browse etc for all beverages kA reset all No WMF 1000 user manual 25 Setting 4 1 Cup size Cup volumes The coffee machine adjusts the recipe set to the new cup volume cup size OK P brwse Selecting the cup size with the P button Select the beverage whose cup volume should be adjusted to the cup size Set the desired cup volume with the and H buttons The cup volume is displayed in 100 corresponds to the current beverage setting cup volume 100 OK P Test bev btn As soon as the cup volume is set as desired confirm the new value with the P button Dispensing test Press the desired beverage button The beverage will be dispensed with the newly set values Each setting can be tested during setting
39. ox Water tank stiff Lightly smear O rings with WMF sealing grease Display side doors open Brewing unit is not inserted correctly or doors are not closed correctly check The lever labeled Press must always be in the level position Pump makes loud noises Water tank is not inserted correctly air in the system Push water tank in completely Bleed machine Dispense hot water until a constant stream of water comes out Hint it is normal if during operation the water pump runs independently from time to time it fills the system automatically 52 WMF 1000 user manual Ww Messages and tips Mf Coffee has no creme e Unsuitable coffee mixture or coffee is not fresh e Quantity of ground coffee is set too low e Cups too cold pre warm e Brewing temperature too low increase temperature Brewing temperature see Chapter 4 Settings gt Basic settings e Grinding degree too coarse set grinding degree finer Grinding degree see Chapter 5 Other Settings Brewing unit can no longer be pulled out or inserted Brewing unit is not in the basic setting x Close the right side door and switch machine on k The brewing unit can be adjusted using the multitool until the brewer can be inserted WMF 1000 user manual 53 Messages and tips Chapter 9 Safety 9 1 Hazards for the user At WMF safety is one of the most important product features The effectivenes
40. pare parts Accessories and spare parts All in one spout 1 piece Milk hose with nipple and nozzle 33 7007 1297 1 piece Air intake cap with o ring 33 7007 1428 1 piece Air intake tube with o ring 33 7007 1298 1 piece Milk lever with o ring 33 7007 1293 1 piece Foam chamber 33 7007 1432 1 piece Spill over cup 33 7007 1429 1 piece Spill over cup complete with air intake 33 7007 1295 Hot water spout 1 piece Hose coupling complete 33 7007 1427 Coffee grounds container drip tray cover 1 piece Filter set 33 7007 1323 1 piece Drip tray 33 7007 1324 1 piece Drip tray grid 33 7007 1217 1 piece Grinder cover 33 7007 1223 1 piece Manual insert cover 33 7007 1224 1 piece Cable compartment cover back side 33 7007 1201 Brewing unit 1 piece Brewer 33 7006 2675 1 piece Tray brewer 33 7006 2621 Water tank Tank filter 1 piece Water tank 33 7007 1322 1 piece Water filter 200 33 2332 2000 1 piece Adapter for water filter 33 2332 0000 Order numbers for the WMF customer care program 1 pack Cleaning tablets blister 3x10 pieces 33 2306 2000 1 bottle Milk foam cleaner 1 litre 33 0683 6000 2 bottles Descaler 0 75 litre 33 7006 2869 60 WMF 1000 user manual Attachment Accessories and spare parts Mf Documentation manuals 1 cover Document set 33 2356 6010 e Installation manual e User manual e Brief manual daily
41. portant Include a copy of the proof of purchase Service maintenance repair in the WMF 1000 Service Center If the location of the WMF 1000 Check of the incoming coffee machine is o tside of Germany lease If there is no warranty claim or if the warranty period contact the WMF branch office in has expired you will receive a cost estimate your country lt Repair in our Service Center within 3 days of receipt of the coffee machine and after agreement to the cost estimate After repair we will return your WMF 1000 promptly via a package service Ta 3 y 3 Return delivery ticket WMF 1000 i i eatin Don t forget to include a copy of the completed return delivery ticket and a copy of your receipt with your package Attention Handling of the shipping of your WMF 1000 occurs via the WMF 1000 Service Center The package is picked up from your premises 58 WMF 1000 user manual W Attachment Technical data Mf Technical data 2 2 kW 1 N PE 50 Hz 230 V VDE CE 320 g 500 g optional 6to 15g 2 8 litres approx 20 portions 75 to 135 mm 15 bar 2 Width 380 mm Height 410 mm Depth 450 mm For the maintenance and cleaning there must be at least 200 mm space on the right side of the machine for brewer disassembly approx 19 0 kg 1 2 kg approx 1 0 m 03 0500 0001 WMF Group WMF 1000 user manual Attachment Accessories and s
42. purchaser or by third parties or by faulty or re Ue i ne negligent treatment f e For the consequences of improper use and changes a tak hrer is required made without our permission or commissioning work of the purchaser or third parties e For defects caused by inappropriate or improper use e Inappropriate use of the coffee machine takes place Pa especially if within the warranty period of 12 months as of the date of purchase the customer exceeds See Maintenance chapter the maximum number of servings than the maximum annual amount specified The maximum amount in a year is 10 000 coffee beverages WMF 1000 user manual 57 Maintenance Chapter 10 Service and maintenance 10 1 WMF 1000 Service Center This procedure applies only in Germany Do you have a question about the operation or function If the location of the WMF 1000 of your WMF 1000 Call our WMF service hotline or send is outside of Germany please us an e mail contact the WMF branch office in e Telephone 07331 25 75 19 your County e E mail ecco service center wmf de If your WMF 1000 requires professional help and your questions cannot be answered on the telephone we will pick up your coffee machine and repair it in the WMF Service Center in Geislingen Then we will send the machine back to you Procedure e Pick up will occur shortly e Prepare your WMF 1000 for shipping packed in the original carton and have it ready for pick up e Im
43. r the hot water spout Start the descaling with the care button The descaling begins A minute countdown indicates how long the descaling will last Mo Ma Me Me Descaling running Remaining time 37 min After approx 30 minutes the following displays appear Empty water tank OK P Empty the water tank and rinse thoroughly with clear water The remaining descaling solution must be emptied from the tank so that the coffee machine can then be rinsed with clear water and no descaling solution remains in the coffee machine Press the P button to activate Total duration of descaling approx 37 minutes The procedure may not be interrupted i Place container underneath Tip Instead of two containers you can use a sufficiently large container which fits under both spouts WMF 1000 user manual 39 Care Refill water tank OK care lt Fill up the water tank Continue the descaling by pressing the care button Ae Descaling running Remaining time 1 min Replace the filter cartridge Fill up the water tank and replace it Replace the all in one spout The machine now heats up Steam and condensed water will escape during this process The water hardness the water flow and whether a tank filter is used determine the schedule for descaling The time will be calculated by the WMF 1000 and the request will appear The descaling can be put off with the Off C button
44. rdness atten Accu aotdines Shes Shee cede EREET 14 Tank fter ct sand miin ache and aekdand arte ang ards ang ardsand arte ae 15 Chapter 3 Operation 3 1 Operating and Lighting concept 16 3 2 Preparing coffee beverages 16 Overview of beverage buttons 0 0 0 0 cece eee eee 16 Example Preparing caf creme 0 c eee eee eee 17 Particularity of caf latte 2 eens 17 Setting coffee strength for the next beverage 0 0000 18 Coffee preparation using the manual insert 000000e 19 3 3 Dispensing milk and milk foam 20 Dispensing milk milk lever down 0 000 e cece eee eee eee 20 Dispensing milk foam milk lever UP 2 ees 20 3 4 Dispensing hot water 21 3 5 Beverage preparation in general 21 3 6 Cancel beverage dispensing 21 3 7 all in one spout 22 Adjusting the height 0 0 0 cece eee eeeee ee nee 22 Positions of the all in one spout 0 0 0 0 0c e cece eee eens 22 3 8 Switching on and off 23 SWITCHES ON zeg wise eo ied e deel ed argon a bese Ree apace E E E eden 23 SWITCHING Off gepa eie Loe sete val eed carved iE a Ea e iE E a dustin E ii 23 WMF 1000 user manual 3 Table of Contents 3 9 Switching coffee machineon and off in timer operation 24 Setting the automatic switch on time 0 0 0 0 eee eee 24 Display timer operation ssa psia etena ansaa ata ni aE AE NEDA a 24 Manual switch on for timer operation n sasaaa nanana 24 Manual switch off for timer oper
45. rst milk then coffee offered for beverages with milk e First coffee then milk components e Milk and coffee together sequ coffee milk OK P change Pre brew pre brew on Yo OK P change The coffee grounds swell and the coffee aroma can a test detail develop Set water quantity i i Page 27 Dispensing test Test Each setting can be tested during setting a P Select aP Confirm rh Care button Browse backwards 5 Reduce value Browse forwards Increase value The new values are saved when you exit the program 28 WMF 1000 user manual Setting Me 4 3 Basic settings Language Time Date Date time Switch on time Switch off time Water hardness Water filter Brewing temperature Factory settings For a description of the basic settings marked with see the Chapter 2 Commissioning Date Time Display of current date and time on the display On Off date time on OK P change You can switch the display of the current date and time on and off here Automatic switch on time switch on time on OK P change You can switch the automatic switch on time for the coffee machine on or off by doing this you activate the possibility of timer operation Switch off time in minutes after the last beverage preparation sw off time 60 min OK P change Here you can set how many minutes after the last beverage preparation the coffee
46. s of safety devices is only warranted if the following points are observed e Read the user manual carefully before use e Do not touch hot machine components e Do not use the coffee machine if it is not working properly or if it is damaged e Do not allow children near the coffee machine e The built in safety systems must under no circum stances be altered Despite safety devices every machine remains fraught with hazards if used incorrectly Please observe the following instructions when using the coffee machine so as to prevent injury and health hazards Scald hazard There is a scald hazard in the coffee milk milk foam and hot water dispensing area Make sure that there is always a container below the beverage spout when dispensing Burn hazard The brewing unit may only be cleaned when the coffee machine is cold The brewing unit can get hot Risk of crushing There is a danger of bruising or crushing when handling all moving parts When the coffee machine is switched on do not reach into the bean hopper or the brewing unit opening A A Disregarding of the hazard instructions can cause serious injuries Ay Attention Scald Hazard near outlet gt Attention Burn Hazard Hot Surfaces A Attention Risk of Crushing 54 WMF 1000 user manual Safety Me Health hazard The bean hopper and manual insert may only be filled with materials for proper use Health hazard When handlin
47. s provided 0 0 0 ccc cee eee eens 57 Chapter 10 Service and maintenance 10 1 WMF 1000 Service Center 58 Proced reca s osme aaran raaa e aa aana RaR o 58 Service maintenance repair in the WMF 1000 Service Center 58 Return delivery ticket WMF1000 0 00 ce eee eee eee 58 Technical data Accessories and spare parts Index WMF 1000 user manual 5 Introduction and General Information Chapter 1 Introduction and General Information 1 1 Parts of the machine 6 WMF 1000 user manual Introduction and General Information Mf Bean hopper Manual insert Heated cup storage Display Hot water button 6 Hot water spout Plus button Aroma button B Minus button Care button Aroma button E P button Confirm Off C button Timer Milk button Milk foam button Beverage buttons Milk lever conversion milk milk foam Height adjustable all in one spout with integrated milk foamer Adjustment lever for all in one spout Water tank Removable drip tray with drip tray grid Coffee grounds container WMF 1000 user manual 7 Introduction and General Information 1 2 Overview of control buttons Off C button e Switching on e Off e Cancel e Timer operation Program button P button e Introduction to settings e Confirm a selection Minus button Care button Aroma button e Browse back in the programs with minus e Select the care program e Reduce coffee strength
48. team Carry out descaling If steam comes out Please call the hotline WMF 1000 user manual 51 Messages and tips 8 3 Problems with no fault display Error Action No milk foam milk output but milk in k Check that milk hose is not kinked or crimped lay milk hose again reservoir Clean all in one spout and milk nozzle See Chapter 6 Customer Care gt Milk system cleaning No milk foam Put milk lever in milk foam position only hot milk Carry out foamer rinse pushing spout completely upwards If necessary check whether the air intake nozzle of the all in one spout is stopped up Milk or milk foam is too cold Ensure that the milk nozzle is on the milk hose Check whether the correct milk nozzle is mounted transparent for refrigerated milk Milk is too hot and there is too little or milk foam has bubbles Milk is too warm Refrigerate milk Check that milk hose is not kinked or crimped Lay milk hose again Check whether the correct milk nozzle is mounted grey for unrefrigerated milk Leakage Check all connections and seals of the all in one spout Milk lever is not all the way up for milk foam or not all the way down for milk Jo Y All in one spout Assembly disassembly is stiff xk Lightly smear o rings with WMF sealing grease and make sure that no grease gets into the air intake opening The grease for sealing rings is in the accessories b
49. tings Dispense milk Milk lever down Dispense milk foam Milk lever up refrigerated milk transparent milk nozzle unrefrigerated milk grey milk nozzle 20 WMF 1000 user manual Operation Me 3 4 Dispense hot water With the hot water function you can dispense hot water for tea for example or pre warm your cups press short press and hold 1 glass hot water Hot water on request Glass of hot water x Place an appropriate drinking vessel under the hot water spout Press the hot water button once short Another press of the hot water button ends the dispensing prematurely Dispensing any quantity of hot water Place an appropriate drinking vessel under the hot water spout Press the hot water button until the desired quantity has been dispensed 3 5 Beverage preparation in general Attention Burning and scalding hazard e The all in one spout and the hot water spout can get very hot e The beverages dispensed and the escaping steam are very hot e Never touch the spouts during or directly after dispensing beverages e Never touch the beverages rinse and cleaning water or steam during or directly after beverage dispensing 3 6 Cancel beverage dispensing You can cancel the current beverage dispensing Press the Off C button Hot water button a Set cup size see Chapter 4 Settings A WMF 1000 user manual 21 Operation 3 7 All in one spout The all
50. uality and protects the coffee machine against calcification With water hardness 0 4 do not use a tank filter Remove the screen built into the water tank 1 Place the cartridge adapter on the water spout supports from above lock pulled and lock by pressing the lock down 2 Unpack the tank filter cartridge and place on the cartridge adapter 3 DPA Cable compartment Keep the original packaging to use for transport Please empty the water tank drip tray filter sets and bean hopper before transporting Fill water tank with drinking water i AN See Tank filter instructions Figures see next page WMF 1000 user manual 11 Commissioning MP Assemble the milk hose The milk hose is already mounted on the all in one spout e For refrigerated milk use the transparent milk nozzle assembled on delivery e For non refrigerated milk use the grey milk nozzle from the accessories Set all in one spout Press the adjustment lever to the right of the spout and then Push the all in one spout to the lowest position move the spout Insert the milk hose into the guide m Fill the water tank Fill the water tank with cold tap water max 2 8 litres k Slide the water tank back into the machine Fill the water tank only with fresh cold water Never use hot water mineral water milk or other liquids 12 WMF 100
51. ve the drip tray and empty it Replace the drip tray There are not enough coffee beans in the coffee bean hopper Grinding is interrupted Pour coffee beans into the bean hopper Press the beverage button again The grinding process continues and the additional coffee required for the brewing cycle is ground The selected beverage is then brewed 48 WMF 1000 user manual Ww Messages and tips Mf Insert coff grounds insert coff grounds select beverage Change tank filter your selection pls replace water filter Side door open locked side door open beverage sel Lower spout lower spout into beverage position The lid manual insert is open k Insert the ground coffee x Close the manual insert amp Select the desired beverage with the beverage button This procedure can be cancelled with the Off C button Already inserted ground coffee is removed via the coffee grounds container The tank filter must be changed Change filter cartridge See Chapter 6 Customer Care The right hand side door of the coffee machine is open Close the right hand side door Close lock completely The all in one spout is in the milk system rinse position k Push the all in one spout further down wards into a beverage position WMF 1000 user manual 49 Messages and tips 8 2 Error messages and faults Essential procedure in case of error messages or faults Switch coffee machine of
Download Pdf Manuals
Related Search