Home

Instructions / Assembly

image

Contents

1. ASSEMBLY INSTRUCTIONS Leg Shelf FRENCH INSTRUCTIONS ON OPPOSITE SIDE FITS ALL MECO GRILLS EXCEPT 4430 4440 amp 9000 SERIES ASSEMBLY For Swinger and Sizzler Grills This Leg Shelf fits all Meco Swinger and Sizzler Grills with tubular legs TOOLS REQUIRED Phillips screwdriver 3 8 open end wrench or pliers STEP 1 Refer to the Illustration that looks most like your grill STEP 2 Slide the Leg Clamp onto the Grill leg STEP 3 Bend the Leg Clamp with your fin gers to make the holes line up with the holes in the Shelf Support Insert a Bolt and tighten Repeat for the other three legs STEP 4 Move the shelf so it is level and about 5 1 4 from the floor Tighten all bolts ECO NMECO P N 03 5139 00 MECO CORPORATION 2005 For Customer Service call 1 800 251 7558 or visit our website at www meco net REV 12 05 INSTRUCTIONS DE MONTAGE de la tablette inferieure REMARQUE ENGLAIS INSTRUCTIONES A LA PAGE OPPOSITE CONVIENT A TOUS LES GRILS MECO SAUF SERIES 4430 4440 ET 9000 MONTAGE Cette tablette inf rieure convient a tous les grils Swinger et Sizzler aux pieds tubulaires OUTILS REQUIS Tournevis Phillips cl ouverte ou pince de 3 8 po ETAPE 1 Consultez le sch ma qui ressemble le plus a votre gril ETAPE 2 Glissez le serre pied sur le pied du gril ETAPE 3 Pliez le serre pied avec les doigts pour faire aligner les trous aux trous du support de tablette Ins
2. Do not touch hot surfaces Use heat resistant gloves long handled tongs or barbecue mitts at all times since the grill will become very hot Do not move a charcoal grill when in use or hot Do not allow children to operate or play near a charcoal grill Keep animals and bystanders out of the grill area Do not leave grill unattended Allow grill to cool before handling parts or cleaning To avoid a fire allow coals to burn out completely and let the ashes cool for 48 hours before dispos ing of them Do not attempt to extinguish a grease fire with water or other liquids Have an ABC fire extinguisher nearby Always have an ABC fire extinguisher baking soda a bucket of sand or a garden hose ready in case of an uncontrolled fire WARNING Combustion by products produced when using this product contain chemicals known to the State of California to cause cancer birth defects or other reproductive harm This product contains chemicals known to the State of California to cause cancer and or birth defects or other reproductive harm Preparation for Assembly TOOLS NEEDED Phillips head Screwdriver and a 3 8 open end wrench or a pair of pliers LAY OUT AND IDENTIFY ALL PARTS DO NOT DISCARD CARTON OR PACKING UNTIL YOUR GRILL IS COMPLETELY ASSEMBLED READ ALL ASSEMBLY AND SAFETY INSTRUCTIONS IN THE OWNER S MANUAL BEFORE YOU START The extra holes in the side of the bowl are for mounting convenient accessories side ta
3. Bolt and Acorn Locknut Do not tighten completely Handle Spacer FIG 2 10 x 1 3 4 Screw Acorn Locknut FIG 3 Step 3 Short Hinge Hinge Assembly Attach Long and Short Hinges to Hood and Bowl FIG 3 Insert Acorn eight 10 24x1 2 Bolts through Hinge holes from inside Hood Locknut and Bowl Attach Acorn Locknuts to Bolts from the outside Do not install Bolts and Nuts the opposite way Do not tighten com pletely so Hood will raise and lower freely 10 24 x 1 2 Bolt FIG 4 Step 4 Front Leg Assembly FIG 4A Install Leg Caps on ends of Front Leg Note The Front Leg does not have holes at the end near the Leg Caps Wheel Leg Assembly Insert an Axle through the center hole on the recessed side of the Wheel The opposite side that is placed against the leg tube has a raised cone shaped center Insert the end of the axle that extends through the wheel through the hole in the end of the Leg Tube Fasten in place by inserting the Cotter Pin through the hole in the end of the Axle FIG 4B Step 5 Bowl Leg Assembly Place Hood and Bowl Assembly on a protective pad or the carton cut out flat on the floor FIG 5 Lay Hood and Bowl Assembly on its back side with Hood resting toward the floor Align the leg holes with holes in bottom of bowl and install six 10 24 x 1 1 4 Bolts from inside the bowl through the legs Attach six Square Nuts and tighten Step 6 Adjusting
4. 423 639 2570 and reference your model number It is important to register your grill and retain your receipt A CAUTION To reduce the risk of a cut pinching or other bodily injury Wear protective gloves when handling parts that could have sharp edges keep hands and fingers away from hinges and pivot points Read and follow these instructions to set up your grill Step 1 Bowl Slide Vent Assembly Attach Slide Vent Covers to front and rear of Bowl FIG 1 Insert 10 24x1 2 Bolts through inside of Bowl and attach Acorn Locknuts to Bolts from opposite side Do not tighten completely so Vent Covers will slide freely from right to left Attach Control Bracket to front of Bowl with four 10 24x1 2 Bolts through inside of Bowl Attach four 10 24 Square Nuts from opposite side Peel backing strip slowly from Control Label and apply to Control Bracket Center label on the bracket and align High Med and Low indicators with the notches Slide Vent Cover FIG 1 10 24 x 1 2 Bolt Control Label Hinge holes AN to rear of S A Sg i Control Bracket SSS Acorn Locknut Square Nut Step 2 Heed Handle 10 24 x 1 2 Bolt Hood Vent Cover Hood Assembly 7 e Assemble Hood Handle and Spacers to Hood with two i 10 x 1 3 4 Screws from inside of Hood FIG 2 Place the wide end of spacers toward the Hood surface Tighten completely Attach Hood Vent Cover on top of Hood with one 10 24 x 1 2
5. fumes and odors e Use barbecue mitts and long handled tongs to spread out the hot charcoal e If there is any type of fire that threatens either personal safety or property call the fire department e To reduce risk of burns from the hot air and steam trapped inside open the Hood carefully when grill roasting Do not grasp the Cooking Grid with your hands while it is hot Use barbecue mitts for handling e If flare ups occur close the Vents for at least one minute to stop flare up Do not use water To reduce the risk of serious injury or death Allow the grill to cool completely before cleaning transporting or storing e Empty and clean the Fire Bowl after each cooking session so excessive grease and ashes do not accumulate See Cleaning instructions on next page Store your charcoal grill in a cool dry place Do not store charcoal and lighter fluid indoors Store out of the reach of children Do not store additional charcoal and lighter fluid under or near the grill while it is hot e To avoid a fire or explosion do not store charcoal or lighter fluid near a heat source Always cap the lighter fluid when not in use To reduce the risk of injury or parts falling out during transport Make sure legs are folded and locked and hood and bowl are latched securely Starting a Fire For Grilling For Indirect Cooking STARTING A CHARCOAL FIRE IN YOUR OneFire SWINGER GRILL STEP 1 Use a high quality hardwood charcoa
6. rez un boulon et resserrez R p tez pour les trois autres pieds TAPE 4 Bougez la tablette pour qu elle soit niveau et environ 13 cm ou 5 po du sol Resserrez tous les boulons NECO MECO CORPORATION 2005 Pour les grils Swinger et Sizzler TABLETTE INF RIEURE SUPPORT DE P N 03 5139 00 For Customer Service call 1 800 251 7558 or visit our website at www meco net REV 12 05
7. the table near the grill to make sure the Brackets slide all the way down over the Rivets P N 03 5138 05 REV 12 12 INSTRUCTIONS DE MONTAGE DE LA TABLETTE DE COTE REMARQUE ENGLAIS INSTRUCTIONES A LA PAGE OPPOSITE ECROU DE BLOCAGE DERRIERE SUPPORT PIVOTANT A sa BOULON 1 1 4 a ECROU DE BLOCAGE SUPPORT PIVOTANT GRILLS CHARIOT 9300 La tablette est alors en position pratique pour le rangement Quand vous tes pr t employer la tablette saisissez le 1 Attachez des boulons 3 8 po partir de l int rieur de la cuvette travers le trou des supports pivotants de la tablette droite devant et le derri re des deux mains et basculez la tablette Sch ma A sa position normale Sch ma C OUTILS REQUIS Tournevis Phillips cl ouverte ou pince de 3 8 po Pour les grils chariot de la s rie 9300 Employez les boulons 1 4 po qui accompagnent le gril Attachez de l ext rieur travers Enfoncez sur la tablette pr s du gril pour vous assurer que les le trou des supports pivotants de la tablette droite et travers le cadre de chariot Sch ma B supports glissent compl tement sur les rivets 2 Attachez les crous de blocage aux boulons resserrez quand ils sont tous les deux attach 3 R p tez les tapes pour la tablette gauche ECO CORPORATION GEO CORPORATIONS 2008 Pour le service a la clientele composez le 1 800 251 7558 ou visitez notre site web www MecoAmerica com
8. ASTER cooking lower the cooking grid by pulling on both knobs and moving them to the outside You can adjust both sides at the same time or one at a time By raising one side and lower ing the other you can cook rare meat and well done at the same time Use the lowest position for searing steaks and hamburgers or when more heat is needed Foods cook very fast at this position so watch your food carefully Raise the grid to the middle slot to finish cooking steaks and hamburgers Start cooking with the grid in the middle position for meats such as pork and chicken that have to be cooked a long time The top grid height is good for baking or warming breads or any time your fire is very hot 2 TILT AWAY HOOD Leave the hood open for Texas Style open air barbecuing Close the hood for Smoker cooking or when you want to hold in all the heat 3 ADJUSTABLE DRAFT Leave the hood vent open for the most heat close it to lower the heat It takes a few minutes for the charcoal to react to the vent adjustment 4 SMOKING For true smoke flavor use chips or chunks of wood from nut or fruit trees such as hickory walnut cherry or apple Soak the chips in water overnight or at least 2 hours before cooking so they will not burn so quickly when you put them on the charcoal After you get the fire started and charcoal spread out scatter the soaked chips on top of the hot charcoal using tongs Spray the Cooking Grid with cooking spray so f
9. Americanes GRILLS SWINGER Model 4100 n A MADE IN THE N dy USA Ry x 0 IMPORTED Ce Charcoal Grill User s Manual neE For Outdoor Household Use Only Not for Commercial Use FIRE Need Help Need to Register Your Grill Looking for Parts amp Accessories lt SRILLS TR Visit us online at www onefiregrills com Or call Customer Service at 1 800 251 7558 PADITIONS FRO e This instruction manual contains important information necessary for the proper assembly and safe use of this appliance Failure to follow these instructions could result in death or serious injury from explosion or fire e Read and follow all warnings and instructions carefully before assembling or using this appliance e Keep this manual for future reference SAVE THESE INSTRUCTIONS P N 03 6632 00 Rev 20130522 DANGER CARBON MONOXIDE HAZARD This appliance can produce carbon monoxide an odorless toxic gas Using it in an enclosed space can kill you Never use this appliance in an enclosed space such as a camper tent car or home This appliance is not intended for and should never be used as a heater Meco Corporation strives to be a quality supplier of consumer products If we omitted any parts needed for assembly or you need troubleshooting information please contact us using our toll free number or visit our website It is important to register your grill and retain your receipt 1 800 251 7558 Consume
10. Rod Assembly Insert the end of the Left Hand Adjusting Rod into the hole underneath the Slide Vent on the left side of Bowl FIG 6A Push and twist the Rod through the hole until the end reaches the hole at the rear of the Bowl FIG 6B Fit the Rod into one of the notches on the left side of the Control Bracket and pull on the back end of the Rod to let the end spring into a rear hole FIG 6C Make sure the part of the rod inside the Bowl lays to the left when in its lowest position Repeat for the Right Hand Adjusting Rod Check to be sure you can position each Rod into each of the three notches in the Control Bracket FIG 6B A A y INSERT UP TO THIS POINT FIG 6A Left Adjusting Rod Se A F f Right Adjusting Rod FIG 7 Step 7 Adjusting Rod Knob and Bowl Handle Assembly Knobs o Position the holes in the Adjusting Rod Knobs over the ends of 8 x 5 8 Screw the Rods FIG 7 Drive the Knobs on with a rubber or wood en mallet If using a hammer use the handle end to drive the Bowl knobs on instead of the metal head Handle Position the Bowl Handle inside the ends of the Control Bracket Insert two 8 x 5 8 Screws through the side holes in the Bracket and into the Handle Tighten both screws securely Step 8 Fire Grate Ash Pan Cooking Grid Assembly Install the Fire Grate Ash Pan in bottom of Bowl Place the Cooking Grid on top of Grid Adjusting Rods FIG 8 Make sure Grid center wi
11. bles and rotisserie For easier set up follow instructions of each step in the order they are written as you look at the diagrams Part Description Quantity 1 __Owners Manual 1 2 3 4 2 Front Leg A 3 Wheel Leg 4 __ Bowl 5 __ Hood 6 _ Handle Spacer 5 a 7 __ Hood Handle 8 Slide Vent Note The Wheel Leg has hole 9 Control Label at the bottom of each end and 10 Control Bracket 11__ Hood Handle 12 Hood Vent 13_ Leg Cap 14__ Wheel 15 Axle 16 Cotter Pin 17__ Hinge Short 18 Hinge Long 19 Knob Adjusting Rod 20 Left Adjusting Rod 21__ Right Adjusting Rod 22 Screw 8 x 5 8 23 Acorn Locknut 24 Square Nut 25 Screw 10 x 1 3 4 26 Bolt 10 24 x 1 2 27 Bolt 10 24 x 1 1 4 28 Ash Pan 29 Cooking Grid 22 Sisal 23 G is shorter than Front Leg i 7 ay 8 AT y 2 GS 5 8 14 15 16 AS Om an a EE LED ing ee IND I I I IN I IN IS IS a aa aa a a Io IN IN If you need replacement parts refer to the Parts Illustrations to find the exact parts you need If you have any questions or need help contact Customer Service at 1 800 251 7558 or go to www onefiregrills com Be sure to have the grill model number If you need a replacement part under warranty a proof of purchase will be necessary You will be asked to forward your proof of purchase via e mail or to fax your proof of purchase to
12. l to make sure you get a good fire Charcoal briquettes made from maple oak birch or elm woods will burn clean with very little smoke and without unpleasant odors STEP 2 Open the hood and all the vents STEP 3 Remove the Cooking Grid Line the bottom of the Bowl with heavy duty aluminum foil STEP 4 Place about three pounds of charcoal 35 40 briquettes in the bottom of the grill STEP 5 Make a pyramid shaped stack near the front of the Bowl and pour on charcoal lighter fluid following the instructions on the container Warning Do not use lighter fluid if you are using instant light briquettes or an electric fire starter STEP 6 Let the lighter fluid soak in for approximately one minute STEP 7 Carefully light the charcoal and let it burn for 20 to 30 minutes or until it is covered with a light gray ash NOTE For a hot fire in a hurry use a fan or a bellows to create extra air movement over the charcoal Be careful not to blow the ashes out of the grill STEP 8 Use long handled tongs to arrange the charcoal in a checkerboard pattern Leave about one half inch of space between each piece of charcoal This will help you to avoid flare up from the meat drippings and will give you more even heat for grilling COOKING ON YOUR OneFire SWINGER GRILL 1 Cooking on the Grids You can adjust the cooking temperature of your grill in three ways For SLOWER cooking move both knobs towards the center of the grill to raise the cooking grid For F
13. ll areas dry before storing Note Do not use oven cleaner or abrasive cleaner on your grill This may cause damage to the paint finish Storage After you have cleaned your grill store it in a clean dry area Leave all the vents open so moisture does not collect inside causing rust If you store your grill outside close the top vent to keep the rain out If rust appears on your grill clean and buff the affected area with steel wool Touch up bare metal with a high heat paint speci fied for barbeque grills Follow paint manufacturer s instructions for use Thank you for purchasing your peFire CHE oa Gribil VS Supported An American Company Youg n y We ve been a family owned American manufacturing company since 1959 and have been con tinuously making BBQ Grills in our East Tennessee factory since 1968 Back in fifty nine we were known as Metals Engineering Company and our first MECO grills were sold all across America and Europe We re still getting letters and emails from folks who use their Swinger grills that have been in their family for more than 20 years By last count we ve sold more than 20 million quality BBQ grills Like many American companies who have managed to prosper through the years we re now a global supplier with global manufacturing operations But we always put America and Americans first doing everything we can to grow and nurture our USA based operations and helping to keep America strong and Americans w
14. ood does not stick then snap the Cooking Grid in place CAUTION Use long barbecue mitts to snap in the grid Place the meat on the grid close the hood and adjust the vent for the desired heat 5 FLARE UPS Close the vent for at least one minute to stop flare ups You do not have to use water 6 PUTTING OUT THE CHARCOAL Save your charcoal to use again by closing the hood and all vents The charcoal will go out in a little while and the next time you cook you will need to add less new charcoal CARE OF YOUR OneFire SWINGER GRILL For easier cleaning and before each time you cook line the bottom of the fire bowl with heavy duty or a double layer of aluminum foil Make sure you leave all the vents uncovered Ashes Remove the ashes as soon as possible after each time you cook but wait until the charcoal has cooled Pour out the ashes or wrap them in the aluminum foil from the bottom of the Bowl Never put hot ashes in a garbage container You can save any leftover charcoal for use next time you cook Use a garden hose to wash out accumulated grease and ashes Let the grill dry before closing Cooking grid Use a detergent and hot water solution just as you would for any cooking equipment A stiff brush may be helpful in removing heavy grease deposits Hood and Bowl Dampen a cloth in hot water and a detergent solution Then wipe both the inside and outside of the hood and bowl CAUTION Be careful around sharp edges of the grill Wipe a
15. orking Thank you so much for your support Sincerely The Entire Family of Meco Employees To validate your warranty register your grill at www onefiregrills com Replacement parts require proof of purchase Please save your receipt Maintain your new grill with the charcoal fire grate ash pan and SAVE 10 off your order Visit www onefiregrills com and search for Model 1040 8 001 At checkout enter Promo Code ONEFIRE FIRE GRILLS 4 Ve Pp SIDE TABLE ASSEMBLY INSTRUCTIONS FRENCH INSTRUCTIONS ON OPPOSITE SIDE 10 24 LOCKNUT 10 24 X 1 1 4 BOLT PIVOT BRACKET 11 9300 CART GRILLS RIVETS TOOLS REQUIRED Phillips screwdriver 3 8 open end wrench or pliers 1 Attach 3 8 Bolts from inside the Bowl through hole in Right Side Table Pivot Brackets Illustration A For Series 9300 Cart Grills Use 1 1 4 Bolts included with grill Attach from outside through hole in Right Side Table Pivot Brackets through the cart frame Illustration B 2 Attach Locknuts to the bolts tighten when both are attached 3 Repeat steps for the Left Side Table ECO CORPORATION MECO CORPORATION 2005 For Customer Service call 1 800 251 7558 or visit our website at www MecoAmerica com The side table is now in a convenient position for storage When you are ready to use the table grasp the front and back with both hands and swing the table to its normal position Illustration C Push down on
16. r Service Department 8 am 4 30 pm E S T Monday Friday MECO CORPORATION 1 423 639 1171 Telephone 1500 Industrial Road www onefiregrills com 1 423 639 2570 Fax Greeneville TN 37745 USA To reduce the risk of serious bodily injury or death Never use a barbecue grill unless all parts of the unit are firmly in place and the grill is stable Never use gasoline kerosene alcohol or other volatile fluids as a starter They can explode Do not use charcoal grill as a space heater Do not use aerosols or store flammable liquids or materials near this charcoal grill Cap lighter fluid immediately and place a safe distance from the grill Instant light briquettes already have the starter blended in Do not use lighter fluid an electric starter solid or metal chimney starters Do not add more instant light briquettes once the fire has been lit To avoid flame ups unpleasant fumes and odors add regular charcoal briquettes if needed Once the barbecue grill has been lit do not touch the charcoal briquettes wood chunks to see if they are hot Never add lighter fluid to already hot or warm coals Do not close Hood on flaming charcoal If closed and re opened the flames could leap out and burn Do not wear loose clothing example hanging shirt tails clothing with frills etc around a charcoal grill while in use or hot Do not lean your body over the charcoal grill when lighting it while it is hot or is in use
17. res under neath are oriented side to side for easy glide height adjustment See Arrows Fire Grate Ashpan a FIG 8 To reduce the risk of serious injury or death from explosion or fire e Be careful when burning charcoal to avoid getting burned from flame heat or hot coals e Be aware of the wind blown sparks e The use of alcohol prescription or non prescription drugs could impair the consumer s ability to properly assemble or safely operate this appliance To reduce the risk of serious injury or death from explosion or fire e Locate your grill an open area away from buildings dry leaves or brush and at least 10 feet away from your house or building Always make sure the grill is on a level stable surface and not tilted toward the front or back Do not use the grill in a garage breezeway carport porch high traffic area on or under any surface that can catch fire Do not use a charcoal grill indoors on recreational vehicles or on boats To reduce the risk of serious injury or death from explosion or fire Make certain you leave the Hood all the way open until the flames have died down e Should electrically operated starters be used be sure they are properly grounded according to local codes Electrical cords should be placed away from walkways or traffic areas e Do not use lighter fluid an electric fire starter solid or chimney starters with instant light charcoal This could cause flame ups unpleasant

Download Pdf Manuals

image

Related Search

Related Contents

    ExtremeWare 7.2.0b37  油分濃度計 OCMA305 メーカーカタログ  取扱説明書 RS-P26 プリンタ - メトラー・トレド - Mettler  IBM ESERVER X205 P4-2.67G  USER`S MANUAL - Galaxy Audio  QLM600 INSTALLATION MANUAL  télécharger le fichier PDF ici - MRC  

Copyright © All rights reserved.
Failed to retrieve file