HT1502W2 User Manual
Contents
1. 21029 Itasca st CHATSWORTH CALIFORNIA 91311 USA www CYRON com Multicolor LED Lighting System Media Highlighter HTP1502W2 HTP2402W2 Thank you for purchasing CYRON Multicolor LED Lighting System This system will bring the latest lighting technology to your home theatre home d cor cabinets and many other areas you choose Installation of the system is simple and it can be done by anyone with little or no electrical experience Nonetheless some custom installations may require professional help Please contact CYRON Technical Support at 818 772 1900 ext 106 for advice General Cautions To reduce the risk of fire electric shock or injury Route and secure cords so that they will not be pinched or damaged To further secure the wires use only insulated staples or plastic ties Not intended for recessed installations Not intended for surface installation inside built in furnishings Do not install the entire system in closed compartments smaller than 4 cubic feet 26 x30 x10 To comply with National Electrical Code NEC and to prevent fire danger run the cords where they are accessible for examination Cords should be visually examined periodically and immediately replaced when any damage is noted Contents Please locate all system components If any of the components are missing or damaged contact CYRON before proceeding with installation 1 x Controller Hub 2 x Light bars 1 x Power supply 4 x M2. and adjust the light angle by twisting the light bars within the brackets Try several angles to achieve the desired results Operation of HTW202 controller is simple Color buttons on the remote correlate to the colors displayed Four different color shows STROBE STEP FADE and COLOR automatically change light colors and patterns with pre programmed sequences 1 The speed of light can be changed using the Up and Down buttons There are 5 different speeds available in STROBE STEP FADE and COLOR modes Brightness can also be adjusted in 5 steps This can only be done when displaying solid colors 2 There are two buttons under R amp G for enabling Soft Mode First ensure the light is off Press the Off button 5 times the light should turn on Next press the orange button to turn on Soft Mode or the green button to turn off Soft Mode Simply turn off the light to save settings For Advanced Users Only 3 Wiring sequences can be altered for products in which the lighting sequence doesn t match the remote the BRG sequence is selected by default First ensure the light is off Next press the off button 5 times the light should turn on Then press Yellow for RGB Blue for GRB or Pink for BRG buttons available on last row Lastly turn the light off to save Optional Settings Turn LED System ON when an outlet is switched on Plug the power supply to a switched power source such as audio receiver s Switched Power or wall outlet that
3. AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES EXPRESS OF IMPLIED IN NO EVENT SHALL CYRON INC BE LIABLE WHETHER IN CONTRACT OR TORT INCLUDING NEGLIGENCE FOR DAMAGES IN EXCESS OF THE PURCHASE PRICE OF THE PRODUCT ACCESSORY OR FOR ANY INDIRECT INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND OR LOSS OF REVENUE OR PROFITS LOSS OF BUSINESS OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS OR ACCESSORIES TO THE FULL EXTENT THESE DAMAGES MAY BE DISCLAIMED BY LAW Some states and jurisdictions do not allow the limitation or exclusion of incidental or consequential damages or limitation on the length of an implied warranty so the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from state to state or from one jurisdiction to another Please mail all warranty claims to CYRON Inc Warranty Claims Wiring Diagram 21029 Itasca st Chatsworth CA 91311 USA Further warranty inquiries warranty cyron com Specifications Supply voltage range 100 240VAC 50 60Hz DC Supply voltage 12VDC Controller output rating 24W nominal 36W peak Working Temperature 20 to 60 C Standby power lt 0 5W
4. is controlled by a wall switch Make sure the outlet is switched on Using the POWER button on the controller make sure the LED System is off Press and hold the MODE button for 3 seconds Now the unit will turn on automatically every time the outlet is turned on LED System remains OFF when an outlet is switched on In a similar process press and hold the PAUSE button for 3 seconds The system will remain off every time the outlet is switched on In this mode the system can only be turned on from the controller by pressing the POWER button Technical Support CYRON s primary goal is 100 customer satisfaction You may call our technical support line or contact us via email 24 7 techsupport cyron com 818 772 1900 x106 In order to continually improve our products we welcome all comments about the product you purchased Thank You Cyron warrants this product against any defects in materials or workmanship for a period of ONE 1 year from the date of purchase The warranty covers normal usage as intended by the factory and does not cover misuse abuse accidents or damages caused due to the acts of God Proof of purchase is required ANY IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY OTHERWISE THE REPAIR REPLACEMENT OR REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER
5. ounting brackets Tapes Hardware Wipes Installations 1 LIGHTBAR LOCATIONS NOTE Depending on the application as few as one or as many as six light bars may be used There are many intended uses and methods of light placement In most of the cases the objective is to place the light bar so it is not directly visible and its projected light is only seen This is particularly important if combined colors such as white are being produced Feel free to experiment with light placement and direction of light projection There may be more than one good location Television Backlighting The best location for television installations is normally behind the TV about 1 to 4 inches from the outer edges left and right in most cases Also vertically center the bars See TV backlighting diagram The exact location may vary depending on the make and model of the TV Cabinets Shelving Furniture Typical locations are Top or bottom of the cabinets behind furniture trimmings on the shelves and behind glass covers Same general locations work well for most objects There are many ways to backlight and accent light Try various positions to achieve the desired results CLEANING a Using the wipes provided test a small area to make sure it does not affect the mounting surfaces Clean the installation surfaces free of dust grease to assure the two sided tape adheres well 3 MOUNTING CLIPS Mounting clips can be secured using the t
6. wo sided tape or screws DO NOT USE SCREWS FOR FASTENING TO ELECTRONIC DEVICES AND SENSITIVE SURFACES CAUTION Tapes may cause discoloration to some surfaces over time Remove one side of the tape liner and apply to the bottom of the clips Apply pressure for 5 seconds to assure adhesion Place clips on the light bars 4 LIGHTBAR PLACEMENT Remove the second side of tape liner Keep the tape surface clean Place the bars in the proper location by pressing on the clips for 5 seconds CAUTION Never press on the clear lens of bars Light bars will get damaged Note the direction of the wires being routed to the hub 5 HUB Mount the hub using screws or tapes Plug the light bar connectors into hub outlets The plugs are polarized and can only be plugged in one direction 6 CONTROLLER Use tape to mount the controller in an accessible location Some painted surfaces may get damaged upon future removal of the tape controller 7 POWER UP Plug the power supply into an AC outlet The plug is polarized one blade is wider than the other as a feature to reduce the risk of electric shock This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact the factory or a qualified electrician Never use with an extension cord unless the plug can be fully inserted Do not alter the plug 8 DC JACK Connect the DC power jack into the controller DC cord Operations Turn the unit on
Download Pdf Manuals
Related Search