WIN100 SERIES - Lux Products
Contents
1. When a unit has first been powered up with the dial in the RUN position your thermostat will begin to control your heating and or air conditioning system according to It s default ENERGY STAR approved program There is a 2 position slide switch to change temperature control modes Slide the switch to the mode you would like to use HEAT Use HEAT mode to warm your home with a Space Heater in HEAT mode HEAT is displayed right of the set temperature COOL Use COOL mode to control your Window Air Conditioner cooling your home in COOL mode COOL is displayed right of the set temperature ON OFF SWITCH Slide the SLIDE switch to OFF when no heating or cooling is desired Heating and cooling will be disabled even though the set temperature room temperature and time will still be in the display DEFAULT PROGRAM As supplied from the factory your thermostat will use its default ENERGY STAR approved program for tem perature control This program and all other settings may be restored to their default values via a SOFTWARE RESET Please refer to DEFAULT TEMPERATURE PRO GRAM for program times and temperatures HOLD Hold is the simplest method to maintain fixed set tem peratures Press HOLD once to enter the temperature HOLD while in RUN or OVERRIDE HOLD will be displayed on the bottom of the display Pressing this button again will toggle HOLD off and return the unit to RUN and the programmed set tempe2. all risks and liability for incidental and consequential damage resulting from installa tion and use of this unit Some states do not allow the exclu Sion of incidental or consequential damages so the above exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Applicable in the U S A only PROGRAMMING CHART The chart below is provided for you to write down your exist ing Weekday and Weekend program times and temperatures in case you have to enter them again at a later time DAY PERIOD HEAT TIME TEMP MON MORN THRU DAY FRI EVE
3. an antenna Pull this sensor out of its clip and bend the wire so that it point straight up This is required for accurate temperature control 4 On the upper right side of the unit there is an On Off switch Place this switch in the OFF position for right now EXTERNAL TEMPERATURE lt SENSOR ON OFF SWITCH MOUNTING WARNING f any plugs do not fit into the free that you are trying to plug into Stop the WIN1O00 is not designed for this application f the cord you are plugging into the WIN100 only has 2 prongs STOP not having a ground wire is unsafe Your Window Air Conditioner or Spacer Heater must have a plug with 3 prongs on t OD 5 Plug the WIN100 straight into a 110 Volt electrical out let on the wall nearest your Air Conditioning Unit or Space Heater 6 Plug in the electrical cord from your Window Air Conditioner or Space Heater directly into the front of the COMPLETING YOUR INSTALLATION 7 Configure your thermostat at this time Refer to OPERATING INSTRUCTIONS 8 Turn the ON OFF switch on the upper right side to the ON position 9 Turn on your Air Conditioner or Space Heater and turn the thermostat all the way up This will allow the WIN100 to control the room temperature and maintain a specific temperature 10 Verify that the Window Air Conditioner or Space Heater and its fan are operating properly When set to a high temperature the heating system should provide warm air
4. not locate where air circulation is poor such as in a corner or an alcove or behind an open door Do not install it where there are unusual heat ing conditions such as in direct sunlight near a lamp television radiator register or fireplace near hot water pipes in a wall near a stove on the other side of the wall S Do not locate in unusual cooling conditions such as ona wall separating an unheated room or in a draft from a stairwell door or win Ow Do not locate in a damp area This can lead to corrosion that will shorten thermostat life Do not install the unit until all construction work and painting has been completed PREPARING THE UNIT 1 The WIN100 comes with 2 G13A size 1 5V Alkaline Button Cell Batteries already installed These batteries power the clock only during nor mal operation They also provide backup power to retain the thermostats programs and settings while it is not plugged into the wall In order to activate them you must remove the black rib bon from between the two batteries prior to using it Use a small regular screwdriver to pry al the battery holder and pull out the black ribbon EXTERNAL TEMPERATURE SENSOR SCREWDRIVER RIBBON BACK OF UNIT 2 When you have the black ribbon out me push the battery compartment back in while lining up the arrows 3 On the back of the WIN 100 there is an External Temperature Sensor that looks like
5. the dial to its RUN position to accept the new value SOFTWARE RESET Use this feature to make all settings and programs return to their default values Press and release RESET button using a pen or pencil It will perform a system check and then returns all settings to their original default values before initiating normal operation t LI NITE T WEEKDAY RESET SE SET WEEKEND PROGRAMS PROGRAMS SET DAY AND TIME NOTE Pressing this button will overwrite your program and install the default values of all temperature programs and setup values into the unit s nonvolatile memory To ease reprogram ming later record your thermostat s programs and settings in the table provided at the page bottom before using this button TEMPERATURE VARIATION SWING Your thermostat works by turning your heating or cooling system on and off whenever the room temper ature varies a certain number of degrees from the set point temperature This variation is the swing Your System should cycle on about 3 to 6 times per hour A Smaller swing number increases the number of cycles so room temperature is more constant A larger swing number decreases the number of cycles saving ener gy in most cases SWING ADJ USTMENT This setting controls when the heating or cooling turns on and off The Swing setting sets the temperature variation the system allows above or below the set temperature before turning on the heating or Cooli
6. Complete Easy To Read INSTALLATION AND OPERATING INSTRUCTIONS lt WIN100 SERIES SMART TEMP ELECTRONIC THERMOSTAT LUX PRODUCTS CORPORATION 43382 05 Mt Laurel New J ersey 08054 USA IMPORTANT Please read all instructions carefully before beginning installation Save them for future reference WARNING FOR USE ONLY WITH AIR CONDITIONERS AND SPACE HEATERS THAT AUTOMATICALLY RESTART COOLING OR HEATING OPERATION AFTER POWER RECONNECTION Thank you for your confidence in our product To obtain the best results from your investment please read these instructions and acquaint yourself with your ated before installing your new thermostat Then follow the installation pro cedures one step at a time This will save you time and minimize the chance of damaging the thermostat and the systems it controls These instructions may contain information beyond that required for your particular installation Please save for future reference COMPATIBILITY _Your WIN100 Programmable Outlet Thermostat is compatible with 120Volt 15 Amp Plug 60 Hz Window Air Conditioning Units and Portable Space Heaters ony It cannot be used with typi y cal 24 V systems hydronics systems or heat pumps Ask your dealer for other LUX thermo Stats to control those systems 1 ON OFF SWITCH 2 SOFT TOUCH BUTTONS 5 EXTERNAL TEMPERATURE 4 HEAT COOL SWITCH 3 LUX SPEED DIAL SENS
7. DE Morning 6 00 AM 70 F 21 C 6 00 AM 78 F 26 C Day 8 00 AM 62 F 17 C 8 00 AM 85 F 30 C Evening 6 00 PM 70 F 21 C 6 00 PM 78 F 26 C Night 10 00 PM 62 F 17 C 10 00 PM 82 F 28 C WEEKDAY PROGRAMMING To change the HEAT or COOL program Set to HEAT if you are using a Space heater Set to COOL if you are using a Window Air Conditioner Rotate dial to SET WEEKDAY PROGRAMS MORN Mo Tu We Th Fr will be displayed with the Start Time flashing Programming is performed in the following order 1 Weekday Morn Start Time 2 Weekday Morn Set Temperature 3 Weekday Day Start Time 4 Weekday Day Set Temperature 5 Weekday Eve Start Time 6 Weekday Eve Set Temperature 7 Weekday Nite Start Time 8 Weekday Nite Set Temperature 9 and so on until Fri Nite is fully programmed at which point pressing NEXT again will begin the list at Mo Fri Morn Start Time Use the UP DOWN keys to change the start time for this period Press UP DOWN buttons to change the time in 15 minute increments Hold UP DOWN button to change the time at a faster rate One period ends at the start time of the next period The end of one period may not be any closer to the beginning of the next period than one 15 minute incre ment Moving a start time too close to the next start time results in the latter time being pushed ahead too Press NEXT to accept the displayed start time and advance t
8. OR Heating and Cooling Electronic Heating and Cooling Programmable Armchair Programming Plugs into normal 110 Volt 15 Easy Programming with LUX Amp Electrical Outlet Speed Dial Patent 5 2 Day Programming 5 673 850 Weekdays and Weekends can Battery Free Nonvolatile Separate Programs for be different Memory For All Programs And Energy Star Compliant Settings Default Energy Star ETL Approved Approved Program User Calibration Positive On Off Switch On Screen Low Battery Easy to Install Indicator 4 Periods Per Day F C Temperature Display 120VAC Powered with Soft Touch Buttons Batteries 2 Minute Short Cycle 2 G13A size 1 5V Alkaline Protection Button Cell Batteries Included For Clock Only Temporary and Constant Temperature Override Adjustable Temperature dif ferential Cycle Rate 1 thru 9 1 Year Warranty ELECTRICAL RATINGS 120V 60 Hz Maximum load is 15 Amps at 120 Volts Power Consumption 2 W maximum Plug and Receptacle NEMA 5 15R normal household 15 Amp receptacle WARNINGS Read all instructions before using this ther mostat To reduce the risk of electric shock this product has a aera bo ip plug that has a third grounding pin This pin will only fit into a grounding ie power outlet If the plug does not fit into the outlet contact a qualified electri cian to install the proper outlet Do not change the plug
9. after a short time Likewise a cooling system should oor cool air after a short time Usually sound can be heard while they are running The rush of mov ing air should be heard within a short time after either has been started 11 Your installation is now complete OPERATING BASICS RUN MODE For the thermostat to function the dial on the face of the thermostat must be turned to the RUN position If you forget to do this it will not work and the door will not close all the way UP DOWN CHANGE KEYS These are the two h keys just right of the unit s onay They are used to adjust set temperatures and make other setting changes Pressing these keys once will adjust a setting one Step in the associated direction f there are many choices for a value usually that set ting will advance while holding one of these keys Some Settings though must be changed one press at a time SET DAY AND TIME To set the correct time after the unit has lost power or after reset 1 Open the door on the front of the thermostat by lifting up the bottom of the door 2 Rotate the dial to SET DAY AND TIME The abbreviation for the day of week will flash 3 Use the UP key to advance to the current day 4 Press NEXT to adjust the time Time will flash 5 Use the UP DOWN keys to set the time 6 Pressing NEXT again will toggle from Set Time to Set Day or vice versa 7 Return the dial to its RUN position TEMPERATURE CONTROL MODES
10. avoid having to reset the day and time 5 Install two new G13A size 1 5V Alkaline Button Cell Batteries batteries Observe the polarity marking pictures shown on the battery cartridge 6 Push the battery compartment back into the WIN100 while lining up the arrows 7 Plug the thermostat back into the wall TECHNICAL ASSISTANCE If you have any problems installing or using this thermostat please reread the instructions carefully Answers to many questions can be found in our online technical support at www luxproducts com If you feel you require assistance please call our offices between 8 00 a m and 4 30 p m Eastern Standard Time Monday through Friday Our number is 856 234 8803 or you can email us directly at techsupport luxproducts com Limited Warranty If this unit fails because of defects in materials or workmanship within one year of date of original purchase LUX will at its option repair or replace it This warranty does not cover damage by accident misuse or fail ure to follow installation instructions Implied warranties are limited in duration to one year from date of original purchase Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you Please return malfunctioning or defective units to the dealer from which purchase was made along with proof of pur chase Please refer to Technical Assistance before return ing thermostat Purchaser assumes
11. in any way Do not use Outdoors Do not use in a bathroom Never locate where it may fall into a bathtub or other water container Do not insert or allow foreign objects to enter any openings as this may cause electric shock fire or damage to the thermostat Do not use in areas where gasoline paint flammable liquids are used or stored Space Heaters can be dangerous if used improperly Be sure to follow all the Warnings and Cautions that came with the instruction manual written by the manufacturer of the Space Heater Avoid the use of an extension cord because the extension cord may overheat and cause risk of fire However if you have to use an extension cord the cord should be a 3 wire grounding type with No 14 AWG minimum size and rated not less than 1875 Watts Use this thermostat only as described in this manual Any other use not recommended by the manufacturer may cause fire electric shock or injury to persons Never clean this thermostat while it is plugged in Turn On Off switch to Off pull out of the wall and then clean by using a rag only CAUTIONS Your thermostat is protected against normal Static electric discharges To minimize the risk of damaging the unit in extremely dry weather touch a grounded metal object before touching your thermostat Be careful not to drop the unit or disturb electronic parts INSTALLATION TOOLS REQUIRED Small regular screwdriver LOCATION Dee Do
12. ng To change this value 1 Rotate the SPEED DIAL to RUN 2 Press NEXT and HOLD simultaneously The Temperature section of the display shows a single digit number between 1 and 9 3 Select one of the 9 values the UP DOWN buttons 4 1 is the maximum comfort setting narrow control 9 is the maximum energy savings setting wide control 5 Press NEXT TEMPERATURE DISPLAY FORMAT This feature allows you to display temperature in either degrees C or degrees F To toggle the display mode from Fahrenheit to Celsius or vice versa press and release NEXT and HOLD simultane ously in lt SET WEEKDAY PROGRAMS gt position BATTERIES MAINTENANCE The WIN100 comes with 2 G13A size 1 5V Alkaline Button Cell Batteries During normal use these batteries are used for the clock only However they also serve as backup power to retain your programs and settings if you unplug it from the wall These 2 batteries will need to be changed once every year The thermostat will alert you when the bat teries are low by displaying LO BATT in the display BATTERY INSTALLATION 1 Remove fresh batteries from their carton 2 Remove the thermostat from the electrical outlet 3 Use a small regular screwdriver to remove the battery car tridge from the back of the thermostat Use the small regular screwdriver to remove the 2 batteries from the holder 4 Remove the used batteries if present and replace them within 90 seconds to
13. o the SET TEMPERATURE it will flash to show that it may be edited The SET TEMPERATURE will be displayed on the right side of the display with the HEAT or COOL indica tor visible depending on which mode you have it in Edit the SET TEMPERATURE then press NEXT to accept and advance to the next period When all the periods for the weekdays have been set the start time for the next weekday Morning period will be displayed to begin editing the settings for that day Complete programming for all weekdays and rotate the dial back to RUN to accept all current values and end the programming session WEEKEND PROGRAMMING Weekend programming is identical to weekday pro gramming except that you must rotate the dial to SET WEEKEND PROGRAMS and the days that you will program are Sa and Su together This two day program will repeat ADVANCED FEATURES CALIBRATION OFFSET Your thermostat is accurately calibrated at the factory to within 1 F An offset value up to 5 F may be added to the temperature value that the thermostat measures This may allow you to match this thermostat to another To change this offset from its default value of 0 1 Open the door on the front of the thermostat 2 Rotate the dial to SET DAY TIME 3 Simultaneously press NEXT and HOLD The Temperature Offset value will flash 4 The default value is 0 and in most cases should remain untouched 5 Use the UP DOWN keys to adjust the offset value 6 tea
14. r ature Changing system mode or rotating the SPEED DIAL will also cancel a HOLD TEMPERATURE OVERRIDE OVERRIDE allows you to change the current SET TEMPERATURE in HEAT of COOL until the next pro gram period without changing your temperature control programs Press an arrow key once While the Set Temperature is flashing press an UP or DOWN key to adjust the set temperature by one degree in the associated direction Holding the key will auto matically advance the setting in the associated direction The OVERRIDE will be canceled at the start of the next program period and the temperature setting will return to its programmed value An OVERRIDE may be terminated by rotating the dial Switching the mode to OFF or initiating a Hold Adjusting the set temperature to its program value will also cancel an OVERRIDE PROGRAMMING EDITING HEAT OR COOL PROGRAMS The WIN100 provides two separate programs one for heat ing and the other for cooling Each program has separate Settings for weekdays and weekends Every day a program cycles through four independent periods You can use the default programs or alter them to suit your schedule DEFAULT TEMPERATURE PROGRAM As supplied from the factory the following ENERGY STAR w program will be used for temperature control in RUN MODE This program and all other software settings may be restored to their default values via a SOFTWARE RESET PERIOD HEAT MODE COOL MO
Download Pdf Manuals
Related Search