Sch. 1057/008 - Elbo Technology
Contents
1. 6 Press The display shows SET DATE gt DD MM YY ddmmyy 00 00 where dd is day mm month and yy the year set Type in the day from 00 to 31 the month 01 to 12 and the last two digits of the current year and press OK to confirm 7 Press the ESC key repeatedly to exit the menu 42 CHANGING THE ACCESS CODE Each user can change his access code by proceeding as follows 1 Type the current access code on the central unit keyboard and press OK to confirm 2 Using the key select the SETTINGS menu press OK to confirm 3 Using key select the CODE SETTINGS menu press OK to confirm The display shows CODE 00 00 4 where nnnn is the current code 4 new 4 digit code different from predefined codes 1234 and from 0000 to 0016 press OK to confirm The display shows DS1057 002 15 LBT 7934 RE INSERT CODE 00 00 5 Re insert new code and press OK to confirm Press ESC repeatedly to exit menu 4 3 DETECTORS EXCLUSION AND INCLUSION possible to intentionally include or exclude volumetric sensors magnetic contacts and magnetic contact auxiliary detectors This function may be useful for example to temporarily isolate a broken detector that continuously signals an alarm allowing to therefore activate the antitheft s2. 11 3 2 3 VMVII Remote COMI Ole ustioni israeliana 11 3 3 Paral 11 3 3 1 VVIIIIIII CC91 9 Key DONG ilaele lilla 11 3 3 2 With the Auxiliary Keyboard pp 12 8825 14 12 3 4 ahaa cot abana obiet 12 3 4 1 With the Central Unit Keyboard pp 12 3 4 2 13 3 4 3 Remote 13 3 5 What to do in case of Signaling on the Central 14 Svsiem Management ilaele 15 4 1 15 4 2 Changing the Access 15 4 3 Detectors EXCIUSION ANd INGI SION orale dae asa 16 43 lDeteciorEXxGIUSION ere larici alal 16 2 BIGGlorRnEIS 16 __ 16 5 1 on cala 16 5 2 1 1 17 5 3 Deleting Event Me MON S 17 Telephone Communicator aiar 18 6 1 Using the Keyboard to Insert Alphanumerical 18 6 2 Operating
3. maintenance indication and the sabotage alarm memory LEDs are blinking red see figure this means that there has been a transmission error and that the command must be repeated i 3 4 3 WITH THE REMOTE CONTROL 1 2 Briefly press the key of the zone to be deactivated 1 for zone 1 2 for zone 2 and 3 for zone 3 1 for zone 1 2 for zone 2 on the 3 remote control Its LED blinks After a short moment the LED turns red for 2 seconds to confirm zone activation Warning if the zone was already deactivated this operation will activate it DS1057 002 13 LBT 7934 3 5 WHAT DO IN CASE OF SIGNALING ON THE CENTRAL UNIT In case of signals on the central unit the first thing to do is understand signal details according to the procedure indicated in paragraph 7 7 7 Icons and their Meanings Then identify possible causes and solutions using the following table Icons Signal Details Central unit sabotage device e Someone tried to remove or Re fasten the device or properly sabotage open the device activating close the cover until the anti the anti violation tamper violation tamper is correctly the device is not correctly pressed subsequently check that mounted on the wall or its the sabotage alarm is no longer cover is not perfectly closed indicated Radio sabotage jamming The radio channel is disturbed First check that it is not caused by an occasional disturbance electric motor n
4. key the letter appears To delete the number press ESC To modify a wrong digit press the lt key until the cursor is positioned above that digit and insert the correct value 6 Press OK to memorize the new phone number 7 In order to insert other phone numbers select a free memory position using the gt key and repeat from point 5 8 Press ESC repeatedly to exit the menu 6 9 CHANGING A PHONE NUMBER It s possible to modify the phone numbers that the central unit will call if specific events should occur To modify a phone number proceed as follows 1 Type the Master access code on the central unit keyboard and press OK to confirm 2 Using the key select the PHONE TRANSMIT menu and press OK to confirm The display shows PHONE TRANSMIT TELEPHONE NUMBERS 09 09 3 Press OK The first memory position for phone numbers appears TELEPHONE NUMBERS N 1 00 00 6 4 Using the key select the phone number to be modified and confirm it by pressing DS1057 002 22 LBT 7934 5 Delete the existing number by pressing ESC and insert new phone number using keyboard long up to 28 characters of digits or pauses To insert a pause press the gt key the letter appears To delete the number press ESC To modify a wrong digit press the key until the cursor is positioned above that digit and insert the
5. access code and press OK in the house icon activated zones are indicated by red LEDs deactivated zones by green LEDs using the remote controls press the xx key on the 3 key remote control or key 4 on the 5 key remote control for 3 seconds the red LED indicates an activated system the green LED a deactivated system TOTAL ACTIVATION 3 1 1 WITH THE CENTRAL UNIT KEYBOARD 1 2 Insert a valid access code on the central unit keyboard it must be able to activate and deactivate all zones and press OK to confirm in case of typing error press ESC to cancel The display shows XXXX FUNCTION KEYS 00 00 6 where xxxx is the name of the user associated to the code Press the key T4 all system zones are activated and the display shows 00 00 e Warning if the access code inserted is not enabled for all zones only the zones for which it is enabled will be activated shown with white numbers on a black background in the icon house 3 1 2 WITH THE AUXILIARY KEYBOARD 1 Type a valid access code on the auxiliary keyboard it must be able to activate and deactivate all zones and press OK to confirm in case of typing error press the key to cancel Wait for system status visualization the LEDs of the house on the keyboard are illuminated red activated zone green deactivated zone and press T4 The LEDs of the house are turned o
6. beep beep 0 5 seconds of command send status or received 5 switching relay outputs In case of relay output 1 relay output A beep beep 0 5 seconds Command successful switching specify the Output A activated or Warning indicates that related output 2 relay output B Output B activated the relay has been correctly closed reopened not that the device connected to the relay worked correctly In case of system status beep beep 0 5 seconds switching specify System Activated activation or deactivation beep beep 0 5 seconds System deactivated A beep beep beep beep beep beep of the central unit indicates an error and that the command has not been executed the entire procedure must be repeated 6 12 6 EXAMPLES Actions required after connecting to the central unit After listening to the activation confirmation message hang up After listening to the deactivation confirmation message hang up output After listening to activation confirmation message hang up output After listening to the activation confirmation message hang up DS1057 002 25 LBT 7934 7 TROUBLE SHOOTING 71 THE TELEPHONE LINE HAS NO SIGNAL Connect a telephone to the phone line used by the Sch 1057 008 central unit if there is no free phone line signal it means that the phone line is not active and that it s necessary to contact your local telephone operator carrier If the phon
7. correct value 6 Press OK to memorize the new phone number 7 In order to modify other phone numbers select them by using the gt key and repeat from point 4 8 Press ESC repeatedly to exit menu 6 10 DELETING A TELEPHONE NUMBER possible to delete any one of the phone numbers that the central unit will call if specific events should occur delete a phone number proceed as follows Type the Master access code on the central unit keyboard and press OK to confirm Using the gt key select the PHONE TRANSMIT menu and press OK to confirm The display shows N PHONE TRANSMIT TELEPHONE NUMBERS 09 09 3 Press The first memory position for phone numbers appears TELEPHONE NUMBERS gt M 1 09 09 Using the key select the phone number to be deleted and confirm it by pressing OK Delete the existing number by pressing ESC and press OK to confirm In order to delete other phone numbers select them using the key and repeat from point 5 Press ESC repeatedly to exit menu e 6 11 INTERRUPTING THE CYCLE OF ALARM PHONE CALLS The phone alarm message is repeated 3 times as shown in the following scheme where main message is the personalized message recorded by the user for example Home of Paolo Verdi via Roma 15 Milan and event message is the specific alarm message pre recorded at the plant
8. during remote controlling procedure the central unit emits a long beep and refuses activation or deactivation commands it s necessary to interrupt the control procedure and free the phone line 6 12 1 REMOTE ACTIVATION DEACTIVATION AUTHORIZATION AND REVOCATION To carry out remote activation and deactivation of the antitheft system it s necessary to authorize the answer incoming calls function of the central unit The central unit in this case will answer incoming calls except when an alarm signal is being sent To authorize the answer to incoming calls 1 Insert the Master access code and press to confirm 2 Using the key select the TECHNICAL MENU and press OK to confirm 3 Insert the Technical access code and press OK to confirm 4 Using the key select the PHONE TRANSMIT menu and press OK to confirm 5 Using key select the PHONE TRANSMIT ADVANCED 1 menu and press OK to confirm 6 Using the key select the ADVANCED 1 ANSWERING DEVICE menu and press OK to confirm The display shows ANSWERING DEVICE gt PSTN 00 007 7 Press OK to confirm The display shows PSTN ANSWER DEVICE DEACTIVATE 00 00 7 8 Using the key select the number of rings 2 4 or 8 after which the central unit will answer incoming calls and press OK to confirm 9 Press ESC repeatedly to exit menu To revoke the answerin
9. possible to selectively activate one or more zones in order to guarantee anti intrusion safety in rooms in which we are not present for example the garage proceed as follows 3 3 1 WITH THE CENTRAL UNIT KEYBOARD 1 On the central unit keyboard type in a valid access code it must be able to activate and deactivate the requested zones and press OK to confirm in case of typing error press ESC to cancel The display shows DS1057 002 11 LBT 7934 XXXX 4 FUNCTION KEYS 00 00 where xxxx is the name of the user associated to the code 2 Press the key corresponding to the zone that is to be activated T1 for zone 1 T2 for zone 2 and T8 for zone 3 The selected zone is activated and is shown on the display as a white number on a black background inside the house in the figure below zone 1 di 00 00 e Warning if the zone was already active this operation will deactivate it 3 3 2 WITH THE AUXILIARY KEYBOARD 1 valid access code on the auxiliary keyboard it must enable to activate and deactivate the requested zone and press OK to confirm in case of typing error press the key to cancel 2 Wait for system status visualization the LEDs of the house the keyboard are illuminated red activated zone green deactivated zone and press the key corresponding to the zone that is to be activated T1 for zone 1 T2 for zone 2 and f
10. select the menu EXCLUSION INCLUSION INCLUDED and press to confirm Press ESC repeatedly to exit menu 5 EVENT CHRONOLOGY The last 128 events that regard the system activation and deactivation intrusion attempts sabotage attempts low battery signals no PSTN line absence of GSM network etc are stored in the central unit s memory 5 1 EVENT LIST To visualize the list of events proceed as follows 1 Insert the Master access code on the central unit keyboard and press to confirm 2 Using the gt key EVENT MEMORY menu and press to confirm The display shows EVENT MEMORY READ MEMORY 09 09 6 3 Press to confirm The display shows the list of events memorized starting from most recent number 001 like in the example shown below 2001 08 30 01 01 VALID CODE 00 00 e 4 Press to read event details or the gt and 4 keys to visualize the preceding or following events 5 After consulting the event memory press ESC repeatedly to exit the menu DS1057 002 16 LBT 7934 5 2 HOW INTERPRET INFORMATION In the event memory the following information is supplied for each event e Event start and finish e start o finish e Events progressive number lower numbers indicate more recent events e Event time and date WARNING time and date values are the ones set on the central
11. the other zones will remain active and will be shown with white numbers on a black background in the icon house 3 2 2 WITH THE AUXILIARY KEYBOARD 1 valid access code on the auxiliary keyboard it must be able to activate and deactivate all zones and press OK to confirm in case of typing error press the key to cancel The status LED blinks green 2 Wait for system status visualization the LEDs of the house the keyboard are illuminated red activated zone green deactivated zone and press T5 3 The LEDs of the house are turned off and if deactivation is successful they will be turned on again after about ten seconds showing the new status of the system green LED deactivated zone Warning if the access code inserted is not enabled for all zones only the enabled zones will be deactivated only some of the LEDs of the house turn green Warning if after pressing T5 the intrusion alarm memory the failure alarm memory the system maintenance indication and the sabotage alarm memory LEDs are blinking red see figure this means that there has been a transmission error and that the command must be repeated 3 2 3 WITH THE REMOTE CONTROL 1 Briefly press key 5 key 3 key remote control LED blinks 2 After a short instant the LEDs of the keys 1 2 and 3 turn green for 2 seconds confirming the deactivation of all zones 3 3 PARTIAL ACTIVATION It s
12. unit regarding the date only the day and month are memorized e Specific event information Examples 012 08 30 16 03 VALID CODE 09 09 Event number 12 at 8 30 of March 16 a valid access code was inserted 0095 14 27 03 01 MAINTENANCE 09 09 Event number 95 precedes event 12 at 14 27 of January 3 central unit the technical menu 5 3 DELETING EVENT MEMORY Warning Deleting is an irreversible operation For event memory operation it s not necessary to delete memorized events since the Sch 1057 008 central unit automatically eliminates the oldest event once 128 events are reached To delete memorized events proceed as follows 1 Insert the Master access code and press to confirm 2 Using key select the TECHNICAL MENU and press OK to confirm 3 Insert the Technical access code and press OK to confirm 4 The EVENT MEMORY is visualized press OK to confirm The display shows EVENT MEMORY 09 09 5 Press OK to confirm Using gt key select the CONFIRM YES menu and press OK to confirm 6 The display shows EVENT MEMORY DELETED 09 09 confirming deletion 7 Press ESC repeatedly to exit menu DS1057 002 17 7934 6 TELEPHONE COMMUNICATOR Warning al
13. zone 1 status request zone 2 status request Short Pressure 1 sec total activation deactivation Long Pressure 3 sec system status request DS1057 002 7 7934 Short Pressure 1 sec Short pressure 1 sec activation deactivation zone 1 a activation deactivation zone 2 Long Pressure 3 sec zone 1 status wy Long pressure 3 sec zone 2 status request green LED deactivated red 5 request green LED deactivated red LED activated LED activated Short Pressure 1 sec Short Pressure 1 sec total system activation deactivation zone 3 activation Long Pressure 3 sec zone 3 status Long Pressure 3 sec system status request green LED deactivated red request green LED deactivated red LED activated LED activated Short pressure 1 sec total system deactivation Long pressure 3 sec system status request green LED deactivated red LED activated 2 ALARMS AND SYSTEM STATUS SIGNALS 2 1 EXTERNAL SIREN _ Acoustic signi Intrusion alam e T e paragraph Sabotage lam 96ExtemalSirenofthe Panicalam mstalationand Sabotage radio lam programmingmanua Total system activatoo___ ii o Total system deactivation 4bees Paral system activation beep 2 2 INTERNAL SIREN Intrusion Alarm See paragraph Sabotage Alarm e 9 5 Central Unit Siren of the P
14. 3 LBT 7934 INTRODUCTION SYMBOLS USED gt indicates key 7 keyboard OK indicates key keyboard A ESC lt indicates the key keyboard ESC indicates key lt on the keyboard GENERAL WARNINGS Batteries must be disposed of according to the laws in force For products that use lithium batteries there is a small risk of explosion if the battery is not disposed of correctly Replace only with batteries of the same type or of equivalent type as recommended by the builder 1 CENTRAL UNIT KEYBOARD AND REMOTE CONTROL 1 1 DESCRIPTION OF CENTRAL UNIT CONTROLS 1 Jack for earphones with microphone 2 Keyboard and LCD display 3 Internal siren 4 Holes for wall mounting in the picture of the front side the holes are closed by finishing caps 5 Lithium batteries Anti violation tamper spring 7 Hole for phone cable input 8 Relay output terminal board connectors max 24 Vc c 1 A 9 Battery connectors 10 Pre perforated phone cable passage Urme 11 Alpha numerical keys for inserting numbers and letters 12 Keys used for menu navigation and for confirming operations 13 Failure signaling LED blinks in case of system failures DS1057 002 4 LBT 7934 14 Liquid crystal display shows the icons that indicate the system s status and the items of the programming menu rest it alternatively shows the cur
15. 9 18 6 3 Recording the Main Message 18 6 4 NIaIRUNESSsagE PIA VO ACK vata bvutlard sgntuaadusadeitadentesianbsusneadseuniadunnpevindsbumalsahouele 19 6 5 WRG SMS MESSAGES 19 6 6 Deleting gt 20 051057 002 2 7934 6 7 SIM Card Expiry RE 21 6 8 Adding new TelephonE Number pp 22 6 9 Changing ia 22 6 10 Deleting A telephone Number pp 23 6 11 Interrupting the Cycle Of Alarm Phone Calls 23 612 Remote C 23 6 12 1 Remote Activation Deactivation Authorization and Revocation 24 6 12 2 ATiswennghaehn 24 6 12 3 Central UMit SIGN AlS acti co E 25 6 12 4 Connecting to the Central Unit i 25 6 12 5 Remote Controlling Procedure 25 6 12 6 ANIM OCS cli alieni otel deri li ife edi alii e 25 7 TOUDI SMOOUING iii 26 7 1 The Telephone Line Has No Signal i 26 7 2 The Telephone Line Works But It s Not Possible to Send Phone Messages 26 7 3 Radio sabotage Sigraling a debba 26 8 GIOSSIV ica 26 DS1057 002
16. INE ALARM MEMORY Is turned on together with the failure signaling LED 13 to indicate and memorize telephone line absence Only valid for models equipped with the PSTN communicator module SYSTEM MAINTENANCE SIGNAL Is turned on to signal access to the TECHNICAL menu DETECTOR ACTIVATION SIGNAL Is turned on together with the failure signaling LED 13 to indicate the activation of a detector DETECTOR DEACTIVATION SIGNAL Is turned on together with the failure signaling LED 13 to indicate the exclusion of one or more detectors ABSENCE OF GSM TELEPHONE LINE ALARM MEMORY Is turned on together with the failure signaling LED 13 to indicate and memorize GSM telephone line absence Only valid for models equipped with the PSTN communicator and GSM modules FAILURE ALARM MEMORY Is turned on together with the failure signaling LED 13 to indicate a failure 2 DESCRIPTION OF THE AUXILIARY CONTROL KEYBOARD Alpha numerical keys for inserting numbers and letters System status signaling LED Crepuscular sensor enables backlighting the keyboard in the presence of insufficient light System status signaling LED green LED zone deactivated red LED zone activated Function keys allow quick access to the programmed functions DS1057 002 6 LBT 7934 10 11 12 1 3 SYSTEM STATUS Summarizes the system s status requested by pressing 4 key green LED system activated nothing to signal red LED alarms or s
17. LBT 7934 SIM EXPIRY 09 00 7 where indicates the month and year memorized 7 Using the keyboard insert the month previous to expiry and the last two digits of the year of expiry of the rechargeable SIM Card For example if SIM Card expires in 2007 type 0407 Press OK to confirm 8 Press ESC repeatedly to exit menu Warning in order to supply correct results this function requires the correct setting of the date on the central unit Sch 1057 008 se paragraph 4 1 Changing Time and Date 6 8 ADDING A NEW TELEPHONE NUMBER possible to memorize up to 6 phone numbers that the central unit will call if specific events should occur Each number may be long from 3 to 28 characters digits or pauses To add a new phone number proceed as follows 1 Type the Master access code on the central unit keyboard and press OK to confirm 2 Using key select the PHONE TRANSMIT menu and press OK to confirm The display shows PHONE TRANSMIT TELEPHONE NUMBERS 09 09 3 Press OK The first memory position for phone numbers appears TELEPHONE NUMBERS N 1 i 00 00 phone number has already been memorized it appears after N 1 4 Using the key select the desired memory position and confirm it by pressing OK 5 Using the keyboard insert the desired phone number To insert a pause press the gt
18. S1057 002 12 LBT 7934 FUNCTION KEYS a 00 00 where xxxx is the name of the user associated to the code and the active zones indicated by white number a black background inside the house Press the key corresponding to the zone to be deactivated T1 for zone 1 T2 for zone 2 e T8 for zone 3 The selected zone is deactivated and is no longer indicated on the display inside the house 4 _ 00 00 e Warning if zone was already deactivated this operation will activate IL 3 4 2 WITH THE AUXILIARY KEYBOARD 1 Type a valid access code on the auxiliary keyboard it must enable to activate and deactivate the requested zone and press OK to confirm in case of typing error press the key to cancel The status LED blinks green Wait for system status visualization the LEDs of the house on the keyboard are illuminated red zone activated green zone deactivated and press the key corresponding to the zone to be activated T1 for zone 1 T2 for zone 2 and for zone 3 The LEDs inside the house are turned off and if activation is successful they turn on again after 10 seconds showing the system s new status green LED zone deactivated Warning if the zone was already deactivated this operation will activate it Warning if after pressing T1 T2 or T3 the intrusion alarm memory the failure alarm memory the system
19. SAGE menu and press OK to confirm The display shows DS1057 002 18 LBT 7934 VOICE MESSAGE PLAYBACK 00 00 6 4 Using key select the RECORDING menu and press to confirm The display shows RECORDING 09 09 5 Press OK After short moment double beep in earphone signals to start recording main message After about ten 10 seconds a new double beep will signal the end of the recording 6 Press ESC repeatedly to exit menu 6 4 MAIN MESSAGE PLAYBACK To playback the main message use the supplied earphone with microphone The earphone plug must be inserted into the apposite jack located on the upper side of the central unit see figure on page 4 Then proceed as follows 1 Insert the Master access code and press to confirm 2 Using key select the PHONE TRANSMIT menu and press OK to confirm 3 Using the key select the VOICE MESSAGE menu and press OK to confirm The display shows VOICE MESSAGE PLAYBACK 09 09 4 PressOKto confirm The display shows PLAYBACK MAIN MESSAGE 09 09 5 Press OK to confirm The display shows MAIN MESSAGE LA PLAYBACK and after short moment the recorded message will be played 6 After message playb
20. XX gt CONFIRM NO 00 00 7 where is the type of event selected Using the gt key select CONFIRM YES and press The display shows DELETE SMS XXXX 00 00 7 In order to delete other SMS messages use key to select the event to which they refer press OK to confirm and repeat from point 7 Press ESC repeatedly to exit menu SIM CARD EXPIRY REMINDER Warning this function requires the installation of the GSM module Sends the previously recorded SMS message SIM EXPIRY see paragraph 6 5 Writing SMS Messages on the first day of the month selected as a reminder for upcoming SIM Card expiry To insert the reminder proceed as follows 1 2 3 4 Type in the Master access code on the central unit keyboard and press OK to confirm Using the key select the TECHNICAL MENU 5 and press OK to confirm Insert the Technical access code and press OK to confirm Using the gt key select the PHONE TRANSMIT menu and press OK to confirm The display shows PHONE TRANSMIT TELEPHONE NUMBERS 00 00 7 Using the gt key select the ADVANCED 1 menu and press OK to confirm The display shows ADVANCED 1 TELESURVEIL CODE 00 00 7 Using the key select the SIM EXPIRY menu and press to confirm The display shows DS1057 002 21
21. ack press ESC repeatedly to exit menu 6 5 WRITING SMS MESSAGES Warning this function requires the installation of the GSM module It allows to write and memorize the SMS messages that the GSM module will send if an alarm event should occur The message may be at the most 40 characters long including spaces To write SMS messages proceed as follows 1 Insert the Master access code on the central unit keyboard and press to confirm 2 Using gt key select the TECHNICAL MENU and press to confirm 3 Insert the Technical access code and press OK to confirm 4 Using the key select the PHONE TRANSMIT menu and press OK to confirm The display shows DS1057 002 19 LBT 7934 PHONE TRANSMIT TELEPHONE NUMBERS 00 00 7 5 Using the key select the ADVANCED 1 menu and press OK The display shows ADVANCED 1 TELESURVEIL CODE 00 00 7 6 Using key select the WRITE SMS menu and press OK The display shows WRITE SMS INTRUSION 00 00 7 Using key select the type of event to which SMS refers to and press OK to confirm 7 display shows XXXX lt gt 00 00 7 where xxxx is type of event selected Insert the SMS message using keyboard for further information see paragraph 6 1 Using the Keyboard to Insert Alphanum
22. anic Alam Installation and Sabotage Radio Alarm e Programming manual 2 3 CENTRAL UNIT SIGNALING Display MI e Alarm DS1057 002 8 LBT 7934 Battery charge indication Signaling of PSTN telephone line busy Total system activation Total system deactivation ato House with some numbered eon Partial system deactivation House with some empty zones System in maintenance 2 4 AUXILIARY CONTROL KEYBOARD em IE SIGNAL Panic Alarm Signaling of PSTN telephone line A busy Signaling of PSTN telephone line absence Total system activation 2 beeps House A red Total system deactivation House all green Manual _ Installation Manual remaining red remaining red System in maintenance 2 5 TELEPHONE COMMUNICATOR If the Sch 1057 008 central unit is equipped with the PSTN c modem communicator module events will be signaled with the following pre recorded messages Event Message Intrusion Intrusion alarm Intrusion alarm Sabotage Sabotage alarm Sabotage alarm Battery Low Battery low Battery low DS1057 002 9 LBT 7934 3 SYSTEM USE Warning before any activation or deactivation operation always check system status To check system status 3 1 on the Sch 1057 008 central unit examine the house icon on the display active zones are showed with a white number on a black background using the auxiliary control keyboard insert a valid
23. ate 218 Tel 02 380 111 75 Fax 02 380 111 80 00043 CIAMPINO ROMA Via L Einaudi 17 19A Tel 06 791 07 30 Fax 06 791 48 97 80013 CASALNUOVO NAPOLI Via Nazionale delle Puglie 3 Tel 081 193 661 20 Fax 081 193 661 04 30030 VIGONOVO VENEZIA Via del Lavoro 71 Tel 049 738 63 00 r a Fax 049 738 63 11 http www yrmetdomus it e mail info urmetdomus it LBT7933 PLANT URMET DOMUS S p A 10154 TORINO ITALY VIA BOLOGNA 188 C Telef 011 24 00 000 RIC AUT Fax 011 24 00 300 323 Call Center 011 23 39 801 I MAT TNA A 150231
24. bers it retries to call all the numbers that did not answer the first time at the most 3 attempts for each phone number the numbers that already answered are not recalled The voice message sent is composed of the main message followed by the specific message pre recorded for that particular event Example Imagine there is a sabotage attempt and that the configured phone numbers for this event are Telephone 1 voice Telephone 2 voice Telephone 4 digital protocol and Telephone 6 SMS Furthermore imagine that Telephone 2 at the time of the call is busy and does not answer The sequence of phone calls made by the Sch 1057 008 central unit will be the following Telephone1 Telephone2 Telephone 4 Telephone 6 Telephone 2 Telephone 2 6 3 RECORDING THE MAIN MESSAGE The objective of the main message is to notify where the event that caused the alarm is taking place For example the main message could be Home of Ambrogio Brambilla via Roma 56 Milan or Bar Al Chicco d Oro piazza Gauguin Rome To record the main message use the supplied earphone with microphone The earphone plug must be inserted into the apposite jack located on the upper side of the central unit see figure on page 4 Then proceed as follows 1 Insert the Master access code and press to confirm 2 Using the gt key select the PHONE TRANSMIT menu and press OK to confirm 3 Using the key select the VOICE MES
25. e line is active but the central unit continues to signal no phone line contact your installer to check that the connection between the central unit Sch 1057 008 and the phone line has not been damaged 7 2 THE TELEPHONE LINE WORKS BUT IT S NOT POSSIBLE TO SEND PHONE MESSAGES If the Sch 1057 008 central unit does not signal an absent telephone line but it s still not possible to send phone messages check the following e I the central unit is connected to the local phone network through a switchboard be sure that it has been configured correctly see paragraph 9 11 1 PSTN Parameters of the Installation and Programming Manual If the central unit uses the GSM module be sure that the SIM Card if rechargeable has not run out of credit 7 3 RADIO SABOTAGE SIGNALING Radio sabotage signaling may be caused by two circumstances 1 fraudulent attempt to violate the alarm system if this is the case contact your installer for a general inspection and if necessary recover the system s full efficiency 2 Changes in the environment in which the system operates check that the signaled device is not covered by material that blocks the passage of radio waves or that in the vicinity there are no electric motors household appliances or electrical or electronic devices in operation some devices on the market do not comply with specific standards and may cause radiofrequency interference Remove material or turn off these devices if pres
26. ent If the problem persists contact your installer 8 GLOSSARY Chime Acoustic warning used to automatically signal the arrival of a person gong DTMF Acronym for Dual Tone Multi Frequency Indicates the tone composition mode of a phone as apposed to decadic GSM Acronym for Global System for Mobile Indicates an international standardized system for mobile digital telecommunications in other words cellular phones Jamming Intentional disturbance by means of interference high power broadcasting masking used to block the reception of comprehensible radio signals PSTN Acronym for Public Switched Telephone Network Indicates the entire analogue phone network and in general any analogue phone line SIM Card Card that identifies the subscriber of a mobile phone service and that must be inserted into the cellular phone or equivalent device Tamper A micro contact protection Zone Each of the areas that compose an anti intrusion system Dividing the rooms that are to be protected and the protection devices into more than one zone is recommended since it enables to activate if necessary only the required detectors The result is an increase in safety and greater comfort because rooms that do not require our presence are protected while it s possible to move freely in others DS1057 002 26 LBT 7934 051057 002 27 7934 051057 002 SUBSIDIARIES 20151 MILANO Via Gallar
27. erical Characters 8 PressOKto confirm The display shows WRITE SMS XXXX 00 00 7 4 In order to write other SMS messages use gt key to select the appropriate event press OK to confirm and repeat from point 7 9 Press ESC repeatedly to exit menu 6 6 DELETING SMS MESSAGES Warning this function requires the installation of the GSM module Allows to delete previously memorized SMS messages To delete an SMS message proceed as follows 1 Master access code the central unit keyboard and press OK to confirm 2 Using key select the TECHNICAL MENU and press OK to confirm 3 Insert the Technical access code and press OK to confirm 4 Using the key select the PHONE TRANSMIT menu and press OK to confirm The display shows PHONE TRANSMIT TELEPHONE NUMBERS 09 00 7 5 Using key select the ADVANCED 1 menu and press to confirm The display shows DS1057 002 20 LBT 7934 6 7 ADVANCED 1 TELESURVEIL CODE 00 00 7 Using the key select the DELETE SMS menu and press to confirm The display shows DELETE SMS INTRUSION 00 00 7 Using key select the type of event to which SMS to be deleted must refer and press OK to confirm The display shows XX
28. ff and if activation is successful they will be turned again on after about ten seconds showing the new status of the system red LED activated zone Warning if the access code inserted is not enabled for all zones only the enabled zones will be activated only some of the LEDs of the house turn red Warning if after pressing T4 the intrusion alarm memory the failure alarm memory the system maintenance indication and the sabotage alarm memory LEDs are blinking red see figure this means that there has been a transmission error and that the command must be repeated 3 1 3 WITH THE REMOTE CONTROL 1 2 Briefly press key 4 key 3 on the 3 key remote control Its LED blinks After a short moment the LEDs of the keys 1 2 and 3 turn red for 2 seconds confirming the activation of all Zones DS1057 002 10 LBT 7934 3 2 TOTAL DEACTIVATION 3 2 1 WITH THE CENTRAL UNIT KEYBOARD 1 central unit keyboard type in a valid access code it must be able to activate and deactivate all zones and press OK to confirm in case of typing error press ESC to cancel The display shows XXXX FUNCTION KEYS 00 00 e where xxxx is the name of the user associated to the code 2 Press T5 all system zones are deactivated and the display shows 00 00 6 Warning if access code inserted is not enabled for all zones only zones for which is enabled will be deactivated
29. ft zones are always present INDICATION OF BATTERIES All of the system s batteries have over 50 residual charge INDICATION OF BATTERIES AT 50 One or more of the system s batteries are charged less than 50 BATTERIES LOW One or more of the system s batteries are almost flat and must be replaced within a month This icon is shown together with the failure signaling LED 13 SYSTEM ACTIVE The lock is turned on when one or more system zones are activated ZONES ACTIVE With the system active the areas of the house icon corresponding to active zones are illuminated SYSTEM DEACTIVATED With the system totally deactivated only the borders of the house are shown DS1057 002 5 L8I 7934 The following icons are normally not present They indicate an alarm a system failure 1 oa MI gt MX SABOTAGE ALARM MEMORY 15 turned on together with the alarm signaling LED 16 to memorize a sabotage type alarm INTRUSION ALARM MEMORY Is turned on together with the alarm signaling LED 16 to memorize a intrusion type alarm PANIC ALARM MEMORY 15 turned on together with the alarm signaling LED 16 to memorize a panic type alarm SIGNALING OF PSTN TELEPHONE LINE BUSY 15 turned on together with the failure signaling LED 13 to indicate a busy phone line during a test Only valid for models equipped with the PSTN communicator module ABSENCE OF PSTN TELEPHONE L
30. g of incoming calls Insert the Master access code and press OK to confirm Using the gt key select the TECHNICAL MENU and press OK to confirm Insert the Technical access code and press OK to confirm Using the gt key select the PHONE TRANSMIT menu and press OK to confirm Using the gt key select the PHONE TRANSMIT ADVANCED 1 menu and press OK to confirm Using the key select the ADVANCED 1 ANSWERING DEVICE menu and press OK to confirm The display shows D PSTN ANSWERING DEVICE 00 007 7 Press OK to confirm The display shows PSTN ANSWERING DEVICE n RINGS 00 007 where n indicates the number of rings after which the central unit responds to incoming calls 8 Using key select the DEACTIVATE menu to deactivate answering incoming calls and press OK to confirm 9 Press ESC repeatedly to exit the menu 6 12 2 ANSWERING MACHINE If the same PSTN telephone line requires the installation of an answering machine the central unit must respond after a number of rings greater than that of the answering machine for the related instructions se paragraph 6 12 4 Connecting to the central unit DS1057 002 24 LBT 7934 In this case to connect to the central unit it necessary to 1 the central units phone number 2 first ring hang up The central unit will respond to the fi
31. he ESC key to exit the activated TECHNICAL menu memory failure Failure See other active signals for details regarding the failure Batteries low One or more batteries of the Immediately contact your installer central unit or other system in order to replace the batteries of devices are low and must be the indicated devices replaced within a month to identify the device with low batteries press OK on the central unit keyboard DS1057 002 14 LBT 7934 4 SYSTEM MANAGEMENT 41 CHANGING TIME AND DATE The display of the central unit alternatively shows the time and date This information is included in every occurrence of the event memory To change the time and date for example for switching to daylight saving time proceed as follows 1 the Master access code on the central unit keyboard and press OK to confirm 2 Using gt key select the SETTINGS menu press to confirm The display shows SETTING TIME AND DATE 00 00 4 3 Press The display shows TIME AND DATE 09 00 7 4 Press The display shows SET TIME hhmm 00 00 7 where hh indicates hours and mm minutes set Type in the current hours from 00 to 23 and minutes from 00 to 59 and press OK to confirm 5 Press OK The display shows TIME AND DATE 09 00 7
32. l the functions illustrated in this chapter are available only for the Sch 1057 008 central units equipped with the PSTN c modem communicator module and connected to the telephone network PSTN or GSM if the central unit is also equipped with the GSM module 6 1 USING THE KEYBOARD TO INSERT ALPHANUMERICAL CHARACTERS The central unit s keyboard allows to type alphanumerical characters Each key allows to select one or more characters as shown in the table below The blinking cursor indicates the insertion point of the new character To type in using the keyboard when required e Repeatedly press the key associated to the character desired until it appears e Use the gt and keys to move to the previous or following position to delete unnecessary characters use the space character e press OK to memorize the name or ESC to exit the procedure without memorizing 1 amp _ lt gt 6 8 CGS 9 VXV2VXV29 o __0 0fspacelr _ 6 2 OPERATING PRINCIPLES In case of alarm the Sch 1057 008 central unit equipped with the communicator module with enabled tone control e calls the first phone number configured to send alarm messages regarding the event e if the number called answers it sends the message hangs up and calls the next number if the number called does not answer within 6 rings it hangs up and calls the next number e after calling all the configured num
33. on shielded electronic device in this case remove the device that is causing the disturbance or provide appropriate shielding in all other cases it is to be considered a hostile act on behalf of a criminal The wrong code has been inserted for 4 times consecutively with the system active possible attempt of fraudulent deactivation Detector intrusion With the system activated the check if there has been an indicated detector has been intrusion attempt if doors or triggered for example through windows with magnetic the magnetic contacts by sensors are closed correctly opening a protected door or and that there are no moving window or through the objects i e ceilings fans volumetric movement sensors curtains or air conditioning flows or rays of direct or reflected sunlight that may deceive the infrared detectors verify that the alarm is longer signaled if solution is found temporarily deactivate the detector see paragraph 4 3 Detectors Exclusion and Inclusion immediately contact your installer PSTN network absent The PSTN communicator module See paragraph does not detect line voltage on 7 Trouble Shooting on page the telephone line 26 GSM network absent The GSM module does not Insert the SIM Card detect the presence of the reactivate or recharge the SIM GSM phone network Card SIM Card missing SIM Card expired or with no credit e maintenance The technical menu has been Press t
34. or zone 3 3 The LEDs of the house are turned off and if activation is successful they will be turned on again after about 10 seconds showing the system s new status red LED activated zone Warning if the zone was already active this operation will deactivate it Warning if after pressing T1 T2 or the intrusion alarm memory the failure alarm memory the system maintenance indication and the sabotage alarm memory LEDs are blinking red see figure this means that there has been a transmission error and that the command must be repeated 3 3 3 WITH THE REMOTE CONTROL 1 Briefly press the key of the zone to be activated 1 for zone 1 2 for zone 2 and for zone 1 for zone 1 2 for zone 2 on 3 key remote control LED blinks 2 After a short moment the LED turns red for 2 seconds to confirm zone activation Warning if the zone was already active this operation will deactivate it 3 4 PARTIAL DEACTIVATION possible to deactivate one or more zones in order to allow access to selected rooms for example the living room while other areas in which we are not present remain protected Proceed as follows 3 4 1 WITH THE CENTRAL UNIT KEYBOARD 1 a valid access code on the auxiliary keyboard it must enable to activate and deactivate the requested zone and press OK to confirm in case of typing error press the ESC key to cancel If for example zone 1 is active the display shows D
35. rent date and time 15 Crepuscular sensor enables the backlighting of the display in the presence of insufficient light 16 Alarm signaling LED blinks in the presence of memorized alarms 17 Function keys allow quick access to programmed functions 1 1 1 ICONS AND THEIR MEANINGS Thanks to the icons that appear on the liquid crystal display the system s status can be monitored at a glance Some icons are always present while others appear only when certain events occur For details regarding each indication proceed as follows e Press the OK key keyboard The first visible icon blinks and the display shows the generic name of the indication Use the gt and 4 keys to move through the different icons displayed e Press the OK key for details regarding the indication for example SABOTAGE ON e Press the key again to visualize the other indications of the same e Press ESC key to finish Through the low batteries indication or alarm it s possible to identify which device has low batteries By consulting the details of the alarm memory sabotage intrusion alarm panic alarm the signal is automatically deleted if the event that caused the alarm has terminated The intrusion alarm and sabotage icons are also automatically deleted when the system is reactivated the icon is no longer displayed The icons regarding the entire system s battery charge and the activation status of the antithe
36. rst incoming call after the first ring 3 Connect to the central unit as explained paragraph 6 12 4 Connecting to the Central Unit 6 12 3 CENTRAL UNIT SIGNALS To communicate the results of the commands the central unit sends out acoustic signals e a beep beep 0 5 seconds long to confirm the correct reception and acceptance of the numbers inserted e a long to indicate e programmed output different from Service e wrong access code wrong command 6 12 4 CONNECTING TO THE CENTRAL UNIT To connect to the central unit 1 the central units phone number 2 central unit responds with a beep beep after the number of configured rings to change the number of rings see chapter 6 12 1 Remote Activation Deactivation Authorization and Revocation 3 After the central unit has confirmed connection move on to the remote controlling procedure 6 12 5 REMOTE CONTROLLING PROCEDURE Follow the procedure illustrated below to control the central unit Sch 1057 008 from a distance ad unit s signal TO convent ee ee a central unit User authentication Master user code 4 beep beep 0 5 seconds First digit received digits beep beep 0 5 seconds Second digit received beep beep 0 5 seconds Third digit received beep beep 0 5 seconds Fourth digit received End of authentication beep beep 0 5 seconds Code accepted Type of command to 3 switching system
37. see paragraph 2 5 Telephone Communicator page 9 10 5 55 0 5 Beep 5 s Delay until locking During message playback it s possible to interrupt the repetition of the current voice message by typing the code 22 on a push button phone with DTMF tones as in the example that follows 10 5 55 0 5 Beep 5 5 Delay until locking gt TYPE 22 II gt CYCLE BLOCKED It is also possible to interrupt the sequence of all calls by typing a valid access code on the keyboard This function is very useful when more than one phone number has been configured to receive that type of alarm for example office personal mobile phone and parents and after receiving the first alarm it is not necessary that the alarm is notified to others Beep Delay until locking Delay until locking 6 12 REMOTE CONTROLLING With a DTMF tone telephone it s possible to remotely control the Sch 1057 008 central unit equipped with PSTN c modem communicator module The possible actions are e activation of the anti theft system requires previous authorization see the following paragraph e deactivation of the anti theft system requires previous authorization see the following paragraph activation of the central unit s relay A auxiliary output activation of the central unit s relay auxiliary output DS1057 002 23 LBT 7934 IL an alarm should occur
38. urmel 06810 DOMUS DS1057 002A LBT 7934 MICROPROCESSOR CENTRAL UNIT WITH DISPLAY AND CONTROL KEYBOARD sch 1057 008 USER S MANUAL SUMMARY 4 Symbol Used gialle 4 C 4 Central Unit Keyboard and Remote mnnn 4 1 1 Description of Central Unit Controls pp 4 1 1 1 5 1 2 Description of the Auxiliary Control Keyboard pp 6 1 3 Description of the Remote Control i 7 Alarms and System Status Signals 8 2 1 8 2 2 TIGI 8 523 central UnitSIgnalIngi ili iaia 8 2 4 AUxillaty Gontrol Keyboards rile 9 2 5 Telephone Communicatof eLilbii lla 9 USE ell 10 3 1 Ca 10 3 1 1 With the Central Unit Keyboard pp 10 3 1 2 With the Auxiliary Keyboard 10 3 1 3 M 10 3 2 lt _________ ____ _ ____ _ _ _ _ _ __ __ 11 3 2 1 With the Central Unit Keyboard rile lib eil e ee ae 11 3 2 2 With The Auxiliary IKE VOOR oriali i e
39. ystem Warning the exclusion function is an emergency solution only the detector must be replaced and included as soon as possible in order to maintain the level of safety guaranteed by the system 4 3 1 DETECTOR EXCLUSION To execute a partial reset proceed as follows 1 Insert the Master access code and press to confirm Using key select the TECHNICAL 5 menu and press OK to confirm Insert the Technical access code and press OK to confirm Using the gt key select the SETTINGS menu and press OK to confirm Using the key select the EXCLUSION INCLUSION SETTINGS menu and press OK to confirm The list of detectors is visualized Using the key select the detector to exclude and press OK to confirm Using the gt key select the menu EXCLUSION INCLUSION EXCLUSION and press OK to confirm Press ESC repeatedly to exit the menu 4 3 2 DETECTOR INCLUSION To execute a partial reset proceed as follows Insert the Master access code and press OK to confirm Using the gt key select the TECHNICAL menu and press OK to confirm Insert the Technical access code and press OK to confirm Using the gt key select the SETTINGS menu and press to confirm Using the gt key select the EXCLUSION INCLUSION SETTINGS menu and press OK to confirm The list of detectors is visualized Using the key select the detector to include and press OK to confirm Using the gt key
40. ystem failure To visualize details insert a valid access code and confirm by pressing OK The information visualized is related to the code inserted For example it regards only the zone that can be activated or deactivated with that specific code inserted in this case no information is given regarding the other zones Press the OK key again to turn off signaling without waiting for the time out period DETECTOR DEACTIVATION SIGNAL Is turned on to indicate the exclusion of one or more detectors INTRUSION ALARM MEMORY Memorizes an intrusion type alarm The indication is cancelled from the memory at next system activation if the cause of the alarm is eliminated FAILURE ALARM MEMORY Memorizes system failure the LED blinks The indication is cancelled from the memory at next system activation if the cause of the alarm is eliminated SYSTEM IN MAINTENANCE SIGNAL Indicates access to the maintenance menu SABOTAGE ALARM MEMORY Memorizes sabotage type alarm The indication is cancelled from the memory at next system activation if the cause of the alarm is eliminated DETECTOR ACTIVATION SIGNAL Is turned on to indicate the activation of a detector for example a door left open or someone who moves in front of a volumetric detector DESCRIPTION OF THE REMOTE CONTROL Short pressure 1 sec Short Pressure 1 sec activation deactivation zone 1 activation deactivation zone 2 Long pressure 3 sec FGF Long Pressure 3 sec
Download Pdf Manuals
Related Search