User manual
Contents
1. 43 Mania SCX600 700 specifications 45 This page left intentionally blank 1 INTRODUCTION Important Thank you for selecting a fixture from the Martin Mania SCX600 700 series This series of automated moving mirror projectors has the following features 9 full colors plus white 7 interchangeable rotating gobos including 2 glass gobos SCX600 or 3 glass gobos SCX700 198 pan and 72 tilt Adjustable focus DMX control with two DMX modes DMX mode 2 gives extended functionality on additional channels Auto triggering and music triggering modes Stand alone single fixture and synchronized master slave modes Professionally designed pre programmed effects macros Rotating gobo indexing SCX700 only Long life 250 Watt halogen lamp SCX600 Long life 150 Watt discharge lamp SCX700 Unpacking The packing material is carefully designed to protect the fixture during shipment always use it to transport the fixture The Mania SCX600 700 is supplied with Lamp the SCX700 discharge lamp is supplied separately to avoid damage during shipping and must be installed before use see Installing the SCX700 lamp on page 26 Power cable and 5 meter 16 4 ft RS 485 XLR cable for data link User manual Mounting U bracket with fasteners Allen key The mirror assembly is secured for transport Before applying power remove all transport packa2. 525 x 172 x 203 mm 20 7 x 6 8 x 8 0 in Height including bracket 408 mm 16 1 in Mania SCX600 weight including bracket 12 3 kg 27 1 1 5 Mania SCX700 weight including bracket 13 0 kg 28 7 lbs Installation Minimum distance to combustible 0 1 m 4 in Minimum distance to illuminated surfaces 1 m 3 3 ft Minimum clearance around fan and air vents 0 1 m 4 in Construction HOUSING Ma prn dee e tegere e antes a Steel and aluminum Source Mania SCX600 lamp 24 V 250 W halogen with integral reflector Mania SCX600 lamp socket G5 3 Mania SCX700 150 W discharge Mania SCX700 lamp socket G12 Control and programming DMX control USITT DMX 512 1990 DMX protocol Mania SCX600 DMX channels 7 mode 1 or 11 mode 2 Mania SCX700 DMX channels 6 mode 1 or 10 mode 2 DMX connections I O 3 locking XLR pin 1 shield 2 cold pin hot Stand alone music trig single fixture and synchronized master slave Stand alone auto trig single fixture and synchronized master slave Individual effects can be set to music trig via DMX Dynamic ef
3. Counter clockwise rotation fast LAM Clockwise rotation medium Counter clockwise rotation medium CWS Clockwise rotation slow COWS Counter clockwise rotation slow 9060 e be Gobo selection 0 gt 7 GIRS Gobo wheel shake gobo 7 1 1 5 8 255 Gobo rotation speed slow fast PAN 8 255 Pan left right TILT 8 255 Tilt up down TSEG RUN Run a general test of all effects UTIL Manually set fixture to software updat Press UPL 1 SURE mode y poale fenn MENT BE LE 16 gt D aa level 1 2 most sensitive 42 Table 2 Control menu Mania SCX600 700 user manual 10 CIRCUIT BOARD LAYOUTS Hall Hall sens sens gobo color 4 J1 ME J10 5 600 700 Main DMX uid J7 I J6 J2 J4 J15 J16 Pan Tilt Color Shutter Gobo Rot Gobo Lamp Lamp Signal 4 Mania SCX600 Power PCB Power Input Fan Fan Rot Gobo SCX700 only Power PCB Transformer Fuse Mania SCX700 EU Power PCB Pil 4 bil x Mania SCX700 US Power PCB Fan Fan Main Power Signal Main PCB Fan Fan MANIA SCX600 700 SPECIFICATIONS Physical Size LXWXxH
4. 6 Replace the lamp and socket in the lampholder Close the cover checking that no wires are trapped and replace the thumbscrew 7 Reset the lamp hours counter see Information readouts on page 21 Service and maintenance 25 SCX700 lamp The Mania SCX700 uses a 150 W discharge lamp Replace the lamp when it reaches the average life specified by the manufacturer Important Use only this type of lamp See Accessories on page 47 for details of replacement lamps Installing any other lamp may damage the fixture Installing the SCX700 lamp 1 Disconnect the fixture from power and allow it to cool for at least 20 minutes 2 Remove the lampholder by removing screws A see illustrations 3 If replacing an old lamp remove it from its ceramic Socket 4 Hold the new lamp by its base do not touch any other part of the lamp Push the lamp pins squarely into the socket in the lampholder see illustration 5 If you touched the bulb or any optical components clean them with a clean lint free cloth wetted with isopropyl alcohol 6 Reinstall the lampholder in the fixture checking that no wires are trapped before screwing on the cover 7 Reapply power and reset the lamp hours counter see Information readouts on page 21 Beam adjustment 1 If the brightest part of the beam is off center 26 Mania SCX600 700 user manual use screw B1 to adjust horizontal lamp alignment use screw B2
5. 32 47 12 18 Macro 2 48 63 19 24 Macro 3 64 79 25 30 Macro4 80 95 31 37 Macro 5 96 111 38 43 Macro 6 112 127 44 49 Macro 7 128 143 50 55 Macro 8 144 159 56 62 Macro 9 160 175 63 68 Macro 10 176 191 69 74 Macro 11 192 207 75 81 Macro 12 208 255 82 100 Reserved No function 10 Pan amp tilt speed DMX mode 2 only 0 7 0 2 Tracking default 8 240 3 94 Fast gt slow 241 245 95 96 Blackout during color and gobo changes 246 250 97 98 Blackout during pan and tilt changes 251 255 99 100 Blackout during color gobo pan and tilt changes 11 Effects speed DMX mode 2 only 0 7 0 2 Tracking default 8 255 3 100 Fast slow Channels 8 11 are available in DMX mode 2 only In DMX mode 1 pan amp tilt speed and effects speed are set to tracking SCX600 DMX protocol 37 8 SCX700 DMX PROTOCOL 38 Channel Value Percent Function 1 Shutter dimmer strobe effect reset With dimming disabled in PER gt INT default 0 18 0 7 Shutter closed 19 38 7 14 Shutter open With dimming enabled in PER gt INT 0 38 0 14 Continuous dimming 0 100 intensity 39 95 15 37 Strobe slow fast 96 103 38 40 Shutter open 104 151 41 59 Random strobe slow fast 152 159 60 62 Shutter open 160 199 63 78 Music triggered shutter 200 207 79 81 Shutter open 208 219 82 85 Lamp on 220 239 86 93 Shutter open 240 247 94 96 Lamp off must be held for 5 seconds 8 min delay before lamp can be restruck
6. Macro 2 48 63 19 24 Macro 3 64 79 25 30 Macro 4 80 95 31 37 Macro 5 96 111 38 43 Macro 6 112 127 44 49 Macro 7 128 143 50 55 Macro 8 144 159 56 62 Macro 9 160 175 63 68 Macro 10 176 191 69 74 Macro 11 192 207 75 81 Macro 12 208 255 82 100 Reserved No function 8 Effects macros DMX mode 2 only 0 15 0 5 No Macro 16 31 6 11 Macro 1 32 47 12 18 Macro 2 48 63 19 24 Macro 3 64 79 25 30 Macro 4 80 95 31 37 Macro 5 96 111 38 43 Macro 6 112 127 44 49 Macro 7 128 143 50 55 Macro 8 144 159 56 62 Macro 9 160 175 63 68 Macro 10 176 191 69 74 Macro 11 192 207 75 81 Macro 12 208 255 82 100 Reserved No function 9 Pan amp tilt speed Mode 2 only 0 7 0 2 Tracking default 8 240 3 94 Fast slow 241 245 95 96 Blackout during color gobo changes 246 250 97 98 Blackout during pan and tilt changes 251 255 99 100 Blackout during color gobo pan and tilt changes 10 Effect speed Mode 2 only 0 7 0 2 Tracking default 8 255 3 100 Fast gt slow Channels 7 10 are available in DMX mode 2 only In DMX mode 1 pan amp tilt speed and effects speed are set to tracking 40 Mania SCX600 700 user manual 9 CONTROL MENUS Factory default settings are shown in bold type Menu Item Options Notes default settings in bold print Addr 1 5 10 DMX address default address 1 PINY Pan invert PATI i TINV Til
7. TZ 2252 ra EFI pac t ek rex 208 W 1 0 A PF 0 942 240 V 50 HZ o bx reda paese d gru cepe 214 W 1 0 A PF 0 945 Mania SCX700 US model Input ier mee kx er 3 prong IEC male socket AG DOWGF QA E eg 115 120 V 60 Hz Mai cus es sua RP paq 3 15 AT Typical power and current 110 V 60 F2 ene ree he 194 W 1 9 A PF 0 950 120V 60Hz 215 W 2 0 A PF 0 905 V volts Hz hertz W watts A amps PF power factor Allow for a deviation of 1096 from typical figures listed above Measurements made at nominal voltage Local supply voltages can vary by 10 Thermal Maximum ambient temperature Ta 40 C 104 F Maximum surface temperature 80 C 176 F Approvals 61 US Listed EU EMG EN 55015 EN 61547 EN 61000 3 3 EN 61000 3 2 EU safety y ze su RR TRE E rau EN 60598 1 EN 60598 2 17 s se au uy te pt mutuam ea Ro Ringe teres UL 1573 Canadian safety CSA C22 2 NO 166 Included items EU models 3 meter 9 8 ft EU power cable 3 x 1 0 mm Schuko male connector 3 meter 9 8 ft EU power cable 3 x 1 0 mm no male connector 5 meter 16 4 ft RS 485 XLR cable for datal
8. mode DMX mode In DMX mode fixtures receive control instructions via the serial data link They will respond to control signals from a DMX controller or from another fixture set as master Selecting DMX music trig or auto trig operating modes The Mania SCX600 700 is supplied set to DMX mode with its DMX address set to 1 If you intend to operate the fixture without a DMX controller you need to set it to stand alone music trig or auto trig mode To switch between DMX auto trig and music trig modes Operation 15 Important 16 1 Apply power to the fixture and wait until the R 5 T message disappears from the display The fixture has now reset 2 Press the Menu button once to enter the control menus 3 Use the Up and Down buttons to scroll to d E Press Enter once to enter the operating mode menu 4 Use the Up and Down buttons to scroll between e NORM DMX mode e SA A Stand alone auto trig mode and e 5 Stand alone music trig mode 5 Press Enter The fixture enters the mode you have selected and will return to this mode when powered off and on Synchronized music trig and auto trig operation You can set multiple fixtures on a serial data link to respond together to a music trig or auto trig signal from one fixture This feature allows synchronized operation without a DMX controller The fixture sending the signal is the master fixture and the fixtures that receive the signal are t
9. over long runs For best results use cable with at least one twisted pair specifically designed for RS 485 applications Your Martin dealer can supply suitable high quality cable in various lengths Connecting the serial data link The fixture s data connections are XLR type wired with pin 1 to ground pin 2 to signal cold and pin 3 to signal hot This is the standard configuration for DMX devices One or more adaptor cables may be required to connect the Mania 5 600 700 to the controller and or other types of fixture because some devices may have 5 pin XLR connectors and others may have reversed signal polarity pin 2 hot and pin 3 cold Connector polarity is normally specified on the device or in the device s user manual 5 pin to 3 pin 3 pin to 5 3 pin to 3 pin Male DMX Female DMX Adaptor Adaptor Phase Reversing Termination Plug Termination Plug Adaptor Male Female Male Female Male Female Male XLR Female XLR 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 3 3 3 3 ga 31120 Ohm 3 120 Ohm 4 4 5 5 P N 11820005 P N 11820004 P N 11820006 P N 91613017 P N 91613018 DMX connectors and polarity To connect the data link 1 Power all devices off 2 If you intend to use DMX controller run a data cable from the DMX controller s data output to the first fixture s data IN socket If the controller has a 5 pin output use a 5 pin male to 3 pin female adaptor cab
10. the fixture to rain or moisture Refer all service not described in this manual to a Martin service technician Never operate the fixture with missing or damaged lenses Glass lenses must be changed if they have become visibly damaged to such an extent that their effectiveness is impaired for example by cracks or deep scratches Never operate the fixture if covers are open or if any component is missing damaged or deformed an unshielded discharge lamp emits dangerous UV radiation that can cause burns and eye damage Protect your hands and eyes with gloves and safety glasses when changing the lamp Do not stare directly into the light output Never look at an exposed lamp while it is lit Replace the lamp if it becomes defective or worn out Protecting yourself and others from burns and fire Never attempt to bypass the thermostatic switch or fuses Always replace defective fuses with ones of the specified type and rating Introduction Keep all combustible materials for example fabric wood paper at least 0 1 meters 4 inches away from the fixture Keep flammable materials well away from the fixture Do not illuminate surfaces within 1 meter 3 3 feet of the fixture Provide a minimum clearance of 0 1 meters 4 inches around fans and air vents Never place filters or other materials over the lens or mirror Allow the fixture to cool before handling Allow the fixture to cool for at least 20 minutes befo
11. to 115 V 60 Hz or 230 V 50 Hz AC power using the switch on the connections panel Setthe switch to 115 V if you have110 120 V 60 Hz AC power Setthe switch to 230 V if you have 220 240 V 50 Hz AC power Mania SCX700 power settings Mania SCX700 EU models can be set to 230 or 240 V 50 Hz AC power using the switch on the connections panel Use the 230 V setting if you have 220 230 V power and use the 240 V setting if you have 230 240 V Mania SCX700 US models do not have a switch and are supplied set up for 110 120 V 60 Hz AC power Installation 9 Warning 10 Installing a cord cap on the power cable The power cable must be fitted with a grounding type cord cap earthed mains plug that matches your AC power distribution system Consult a qualified electrician if you have any doubts about proper installation If you need to fit a cord cap follow the cord cap manufacturer s instructions connecting the yellow and green wire to ground earth the brown wire to live and the blue wire to neutral The table below shows some pin identification schemes Wire Pin Marking Screw color brown live L yellow or brass blue neutral N silver yellow green ground L green Table 1 Cord cap wiring Rigging the fixture The Mania SCX600 700 must be mounted by means of its adjustable U bracket Do not install the fixture by any other means as this can cause the fixture to overheat The U bracket
12. 00 Aarhus Denmark Tel 445 8740 0000 0 Fax 45 8740 0010
13. 17 DMX termination plug start of link master slave XLR female P N 91613018 uus eel eb rae eU Ea cede ets P N 91602003 Half coupler clamp 4 P N 91602005 5 pin male to 3 pin female XLR adaptor cable P N 11820005 5 meter 16 4 ft RS 485 XLR cable for data link P N 11820008 Mania SCX600 all models main fuse 3 15 P N 05020043 Mania SCX700 EU models main fuse 2 P N 05020009 Mania SCX700 US models main fuse 3 15 P N 05020043 Ordering information Mania SCX600 EU model 220 240 V 50 2 P N 90430082 Mania SCX600 US model 110 120 V 60 2 P N 90430083 Mania SCX 700 EU model 220 240 V 50 2 P N 90430084 Mania SCX 700 US model 110 120 V 60 2 P N 90430085 Disposing of this product Martin products are supplied in compliance with Directive 2002 96 EC of the European Parliament and of the Council of the European Union on WEEE Waste Electrical and Electronic Equipment as amended by Directive 2003 108 EC where applicable Help preserve the environment Ensure that this product is recycled at the end of its life Your supplier can give details of local arrangements for the disposal of Martin products v Mart n www martin com Olof Palmes All 18 82
14. 248 251 97 98 Shutter open 252 255 99 100 Reset must be held for 5 seconds to blackout and reset Color wheel positions and rotation music trig color 2 chase Continuously scrolling color wheel positions 0 0 White 12 4 Color 1 Blue 04 24 9 Color 2 Red B14 36 14 Color 3 Yellow 02 48 18 Color 4 Magenta B12M 60 23 Color 5 Cyan BO5 72 28 Color 6 Green B08 84 33 Color 7 Orange B09 96 37 Color 8 Congo B13 108 42 Color 9 Pink B16 Indexed color wheel positions 120 128 47 50 White 129 135 51 52 Color 1 Blue B04 136 142 53 55 Color 2 Red B14 143 149 56 58 Color 3 Yellow B02 150 156 59 61 Color 4 Magenta B12M 157 163 62 64 5 Cyan B05 164 170 65 66 6 Green B08 171 177 67 69 Color 7 Orange B09 178 184 70 72 8 Congo B13 185 191 73 74 Color 9 Pink B16 Continuous color wheel rotation 192 215 75 84 CW fast gt slow 216 239 85 93 CCW slow fast Music triggered color chase 240 245 94 96 Fast 246 250 97 98 Medium 251 255 99 100 Slow Mania SCX600 700 user manual Channel Value Percent Function 3 Gobo selection gobo shake music trig gobo chase Gobo indexing select gobo set indexing angle on channel 4 0 7 0 2 Open 8 15 3 5 Gobo 1 Parasol twist 16 23 6 8 Gobo 2 Plaid dream cyan B20 24 31 9 11 Gobo 3 Cartwheel 32 39 12 14 Gobo 4 Plaid dream think pink B12M 40 47 15 18 Gobo 5 Spiral galaxy 48 55 19 21 Gobo 6 Moons blue 04 56 63 22 24 Gobo 7 Radial burst G
15. 44 49 Gobo 7 Flying disc Gobo shake 128 143 50 55 Gobo 1 shake fast gt slow 144 159 56 62 Gobo 2 shake fast slow 160 175 63 68 Gobo 3 shake fast gt slow 176 191 69 74 Gobo 4 shake fast slow 192 207 75 81 Gobo 5 shake fast gt slow 208 223 82 87 Gobo 6 shake fast gt slow 224 239 88 93 Gobo 7 shake fast slow Music triggered gobo chase 240 245 94 96 Fast 246 250 97 98 Medium 251 255 99 100 Slow 5 Gobo rotation type music trig gobo rotation speed Gobo rotation type select gobo on channel 4 0 7 0 2 Stop 8 77 3 29 Rotation CW slow fast 78 147 30 57 Rotation CCW fast slow 148 153 58 59 Stop 154 223 60 87 Rotation CW slow fast 224 239 88 93 Rotation shake Music triggered rotation 240 245 94 96 246 250 97 98 Medium 251 255 99 100 Slow Pan 0 255 0 100 Left right 128 neutral 7 Tilt 0 255 0 100 Down up 128 neutral 8 Pan amp tilt macros DMX mode 2 only 0 15 0 5 No Macro 16 31 6 11 Macro 1 32 47 12 18 Macro 2 48 63 19 24 Macro 3 64 79 25 30 Macro 4 80 95 31 37 Macro 5 96 111 38 43 Macro 6 112 127 44 49 Macro 7 128 143 50 55 Macro 8 144 159 56 62 Macro 9 160 175 63 68 Macro 10 176 191 69 74 Macro 11 192 207 75 81 Macro 12 208 255 82 100 Reserved No function Mania SCX600 700 user manual Channel Value Percent Function 9 Effects macros DMX mode 2 only 0 15 0 5 No Macro 16 31 6 11 Macro 1
16. EV music level menu Press Enter 3 The fixture is supplied set to level 7 You can adjust the music sensitivity level using the Up and Down buttons to select a level from LE 1 to LE 16 Level 1 gives highest sensitivity Press Enter to activate the selected level 4 Repeat step 3 until you find a level that gives the best response to the music beat 5 Press Menu to save your setting and exit the music level menu The fixture will return to this setting when you power it off and on Mania SCX600 700 user manual 4 CONTROL PANEL The following functions of the control panel are described earlier in this manual selecting stand alone music trig or auto trig operation see page 15 switching between DMX modes 1 and 2 see page 17 setting DMX addresses see page 17 setting music sensitivity level for music trig operation see page 20 This chapter describes the other control panel options for setting up fixture behavior see also Control menus on page 41 for a complete overview of control panel functions Movement PATI the pan and tilt invert menu allows you to invert pan movement PIN and invert tilt movement These options can be useful in situations where you want some fixtures to mirror the performance of others with the same DMX address or when you install fixtures in a different orientation after you have programmed a light show Mania SCX700 dimming In the Mania SCX700 the Person
17. Mania SC X600 700 user manual DIMENSIONS All dimensions are in millimeters 240 2005 2007 Martin Professional A S Denmark Martin Professional A S Denmark All rights reserved No part of this manual may be reproduced in any form or by any means without permission in writing from Martin Profes sional A S Information subject to change without notice Martin Professional A S and all affiliated companies disclaim liability for any injury damage direct or indirect loss conse quential or economic loss or any other loss occasioned by the use of inability to use or reli ance on the information contained in this manual P N 35000169 Rev D Contents Introd ction ME 5 Unpacking stave Pia eben wale ae Ra PERAGI wana 5 Mania SCX600 700 overview 6 Safety information 7 Installation 9 AG POW then Rene bx ee 9 Rigging the fixture 10 Creating a data link for DMX or synchronized operation 11 Operation p 4 42 2 iab bi vend 14 Gettilig started oer tue de EMI wa ek ie 14 Music trig auto trig and DMX modes 15 Synchronized music trig and auto trig operat
18. ality gt Intensity setting PER INT lets you use the shutter for dimming When disabled the default setting the low values on channel 1 set the shutter to either fully open or fully closed When enabled the shutter can be opened and closed gradually giving 0 100 continuous dimming Information readouts INF D the information menu gives information about hours of fixture and lamp operation and software version Control panel 21 22 Power on hours This readout can be used to track maintenance intervals There is a resettable counter in this menu Read the number of hours the fixture has been powered on since the counter was reset in INFUSTIMESHRSSRSE T Press Enter to display Press Up for 5 seconds to reset the counter to zero Read the total number of hours the fixture has been powered on since fabrication in INF 05 TIMES HRS TOTL Press Enter to display Lamp hours This readout can be used to monitor lamp life for replacement purposes There is a resettable lamp hours counter in this menu Read the number of hours the lamp has been powered on since the counter was reset in INFU STIMESL HR RSET Press Enter to display Press Up for 5 seconds to reset the counter to zero each time you install a new lamp Read the total number of hours of lamp use since fabrication in INFO STIMESL Press Enter to display Start up lamp strike counter INFUSTIMESLSTSRSET is a resettable start up counte
19. and or B3 to adjust vertical lamp alignment 2 If there is an excessive hot spot or dark area in the center of the beam or if light output is low turn all three screws B1 B2 and B3 by an equal amount in the direction that gives an improvement until a satisfactory beam is obtained Cleaning Cleaning optical components Use care when cleaning optical components The coated surfaces are fragile and even small scratches may be visible in the fixture s light output Wear cotton gloves to avoid contaminating components with grease from your fingers 1 Disconnect the fixture from power and allow it to cool for at least 20 minutes 2 Loosen the lamp cover release thumbscrew and open the lamp cover on its hinge 3 Blow or vacuum away loose dust Remove residues from lenses and filters with a soft cloth or cotton swabs wetted with isopropyl alcohol Regular glass cleaner may also be used but no residues may remain 4 Rinse with distilled water Mixing the water with a small amount of wetting agent such as Kodak Photoflo will help prevent streaking and spotting 5 Dry with a clean soft and lint free cloth or blow dry with compressed air 6 Replace the lamp cover before reapplying power Cleaning the fan and air vents To maintain adequate cooling dust must be cleaned from the fan and air vents periodically Cleaning intervals will depend on the operating environment The presence of airborne dust smoke etc will make frequent cl
20. can be either fastened to a flat surface or attached to a rigging clamp Suitable rigging clamps are available from your Martin dealer Block access below the work area and work from a stable platform when installing or servicing the fixture Do not operate the fixture without fastening it securely to a structure or surface Always use a secure means of secondary attachment that can hold at least 10 times the weight of the fixture 1 The fixture must be located at least 1 meter 3 3 ft away from the surface to be illuminated and at least 0 1 meters 4 in from any combustible materials wood fabric paper etc Ensure that the clearance around the fan and air vents is at least 0 1 meters 4 in Ensure that there are no inflammable materials nearby Mania SCX600 700 user manual Important 2 If using a rigging clamp ensure that the clamp is undamaged and bear at least 10 times the fixture s weight Bolt the clamp securely to the fixture s mounting bracket with a grade 8 8 minimum M12 bolt and lock nut through the 13 mm hole in the center of the mounting bracket or as recommended by the clamp manufacturer 3 If fastening the fixture directly to a mounting surface ensure that any fasteners used and the mounting surface can bear at least 10 times the fixture s weight The fixture may be fastened using any of the following four 6 5mm holes in the sides of the U bracket two 8mm holes in the top of the U bracket
21. d both the Menu and the Enter button pressed in while powering on the fixture data LED will blink when the Mania SCX600 700 is in hard boot mode If you have difficulty carrying out uploads your Martin dealer will be able to give advice or carry out the upload for you Service and maintenance 33 6 TROUBLESHOOTING 34 Problem Probable cause s Remedy One or more fixtures is completely dead No power to fixture Check that power is switched on and cables are plugged in Main fuse blown Replace fuse Fixtures reset correctly but all respond erratically or not at all to controller Controller not connected Connect controller XLR pin out of controller does not match pin out of first fixture on link i e polarity is reversed Install a phase reversing cable between controller and first fixture on link Fixtures reset correctly but some respond erratically or not at all to controller Bad data link connection Inspect connections and cables Correct poor connections Repair or replace damaged cables Data link not terminated with 120 Ohm termination plug Insert termination plug in output of last fixture on link Incorrect fixture addressing Check DMX addresses One of the fixtures is transmitting as a master Check all fixture settings One of the fixtures is defective Bypass one fixture at a time unplug both DMX connectors and c
22. d shutter 200 207 79 81 Shutter open 208 247 82 96 Music trigger intensity 248 251 97 98 Shutter open 252 255 99 100 Reset hold for 5 seconds to blackout and reset Dimmer 0 255 0 100 0 100 Color wheel positions music triggered color chase Continuously scrolling color wheel positions 0 0 White 12 4 Color 1 Blue 04 24 9 Color 2 Red B14 36 14 Color 3 Yellow B02 48 18 Color 4 Magenta B12M 60 23 Color 5 Cyan B05 72 28 Color 6 Green B08 84 33 Color 7 Orange B09 96 37 Color 8 Congo B13 108 42 Color 9 Pink B16 Indexed color wheel positions 120 128 47 50 White 129 135 51 52 Color 1 Blue B04 136 142 53 55 Color 2 Red B14 143 149 56 58 Color 3 Yellow B02 150 156 59 61 Color 4 Magenta B12M 157 163 62 64 Color 5 Cyan B05 164 170 65 66 Color 6 Green B08 171 177 67 69 7 Orange B09 178 184 70 72 8 Congo B13 185 191 73 74 Color 9 Pink B16 Continuous color wheel rotation 192 215 75 84 CW fast gt slow 216 239 85 93 slow fast Music triggered color chase 240 245 94 96 Fast 246 250 97 98 Medium 251 255 99 100 Slow SCX600 DMX protocol 35 36 Channel Value Percent Function 4 Gobo selection gobo shake music trig gobo chase Select gobo set rotation type on channel 5 0 15 0 5 Open 16 31 6 11 Gobo 1 Segments 32 47 12 18 2 Vortex 48 63 19 24 3 Cartwheel 64 79 25 30 Gobo 4 Deltawindow 80 95 31 37 Gobo 5 Red Petals 96 111 38 43 Gobo 6 Straws 112 127
23. eaning necessary Check and if necessary clean fixtures regularly 1 Disconnect the fixture from power and allow to cool for at least 20 minutes 2 Loosen the lamp cover release thumbscrew and open the lamp cover on its hinge Service and maintenance 27 28 3 Remove the two Philips head screws on the fan housing and lift out the fan for access see illustration 4 Remove dust and dirt from the fan blades and vent grill using a soft brush or cotton swab and vacuum 5 Replace the fan making sure no wires are trapped 6 Replace the lamp cover before reapplying power Replacing the main fuse The Mania SCX600 700 uses a time delay fuse for protection against current overload An indication that the fuse may have blown is that when power is applied and the lamp is switched on no light is produced If the fuse blows repeatedly there is a fault with the unit that requires service by a Martin technician Never bypass the fuse or replace it with one of another type or rating 1 Disconnect the fixture from power and allow to cool for at least 20 minutes 2 Pry open the fuse holder located next to the power cable entry with a flat head screwdriver and remove the fuse 3 Replace the fuse with one of the same type Fuse ratings are listed on serial number labels and under Electrical on page 46 4 Replace the fuse holder 5 If fuses continue to blow there is probably a fault Disconnect the fixture f
24. eferred to a qualified technician Disconnect the fixture from power and allow it to cool for at least 20 minutes before removing any cover Wear safety glasses and gloves and allow the fixture to cool for at least 20 minutes before removing the lamp Excessive dust grease and smoke fluid buildup degrades performance and causes overheating and damage to the fixture that is not covered by the warranty Check and if necessary clean fixtures at regular intervals SCX600 lamp The Mania SCX600 uses a 24 V 250 W halogen lamp with integral reflector Use only this type of lamp See Accessories on page 47 for details of replacement lamps Installing any other lamp may damage the fixture Replacing the lamp 1 Disconnect the fixture from power and allow it to cool for at least 20 minutes Mania SCX600 700 user manual 2 Remove the lamp cover release thumbscrew and open the lamp cover on its hinge Lamp cover A d release thumbscrew 3 Remove the old lamp and socket from the lampholder and being careful not to strain any wires gently pull the lamp off its ceramic socket 4 Hold the new lamp by its base do not touch any other part of the lamp Push the lamp pins squarely into the ceramic socket 5 If you touched the bulb the reflector or any optical components clean them with a clean lint free cloth wetted with isopropyl alcohol Alcohol is extremely inflammable so take precautions to avoid fire risk
25. elect tracking on these channels the DMX controller defines fade times Unsure about speed and tracking As a rule you should set the fixture to tracking if you are using programmed fade times or macros on your DMX controller Select an effects speed if you are not using programmed fade times or macros on your DMX controller However if you are using fade times on your controller and have set the fixture to tracking but effects movement is rough and irregular setting fade times on your controller to zero and selecting an effects speed may give smoother movement Effects movement is set to tracking if the fixture is in DMX mode 1 and by default DMX signal indicator When the Mania SCX600 700 receives a valid DMX signal the Data LED will light to show that the fixture is receiving control data Operation 19 Focus adjustment Never look directly into the light beam while adjusting the focus The focus adjustment screw is next to the lens aperture Do not confuse it with the lamp cover release thumbscrew Focus adjustment knob Adjusting music level sensitivity you can adjust response to a music beat while a fixture is in music trig mode by adjusting music level sensitivity 1 With the fixture powered on and in music trig mode play a typical music track at typical volume for your location 2 Press the Menu button once and use the Up and Down buttons to scroll to U T IL Press Enter and scroll to ML
26. fects Color wheel 9 interchangeable dichroic color filters plus open position Rotating gobo wheel 7 interchangeable rotating gobos SCX600 5 metal 2 coated glass SCX700 4 metal 3 coated glass Gobo angle indexing Mania SCX700 only Gobo rotation and shake effects Mechanical shutter with variable frequency strobe effects Moving mirror 198 pan and 72 tilt Full range continuous dimming Optics Manual foGus Ee aln tct Rn 2m 6 6 ft 20m 65 6 ft Beamangle cle rhe pe LER Rd SPA AE T 17 6 Electrical Mania SCX600 all models Input ce beet ees 3 prong IEC male socket AC power switch selectable 110 120 V 60 Hz 220 240 V 50 Hz Main TUS Esan ae a 3 15 AT Typical power and current Q 110 60 2 241 W 2 2 A PF 0 993 Q 120 V 60 HZ dem theEPRe 278 W 2 3 A PF 0 993 220 V oreet ehem RR EGRE 241 W 1 1 A PF 0 995 p 230 V 50 HZ sede Ruhe 260 W 1 2 A PF 0 995 240 V S0 HZ pase ger 278 W 1 2 A PF 0 994 Mania SCX700 EU model aia tes XR hana Wawa 3 prong IEC male socket AC power switch selectable 230 V 240 V 50 Hz Main USB cusa pu haqa wa cud PT EDEN LI P Pd 2 AT Typical power and current 0220 V 50 Hz 193 W 1 0 A PF 0 955 230 V 5b0
27. ging remove the protective film from the mirror and cut and remove all plastic tie wraps holding the mirror Introduction 5 Mania SCX600 700 overview Control panel and display Swivel lock Power on off switch DMX out Power cable connector and fuseholder AC voltage selector switch SCX700 EU and SCX600 only Connections panel Mania SCX600 700 user manual Warning Safety information This product is for professional use only It is not for household use This product presents risks of lethal or severe injury due to fire and heat electric shock ultraviolet radiation lamp explosion and falls Read this manual before installing or powering the fixture follow the safety precautions listed below and observe all warnings in this manual and on the fixture If you have any questions about how to operate the fixture safely please contact your Martin dealer or call the Martin 24 hour service hotline Protecting yourself and others from electric shock and injury Disconnect the fixture from AC power before removing or installing the lamp fuse or any part and when not in use Always ground earth the fixture electrically Do not use the fixture with a damaged power cable or cord cap mains plug Use only a source of AC power that complies with local building and electrical codes and has both overload and ground fault protection Do not expose
28. hat the gobo is held securely 5 Replace the lamp cover securely before reapplying power Gobo orientation Focus is easiest to maintain if all coated gobos in a fixture are installed with their coatings as close as possible to the same plane of focus The coated gobos in the Mania SCX600 700 are factory installed with their coated side facing away from the lamp If there is a risk of heat damage on a custom coated gobo the first priority is normally to ensure that more reflective sides face towards the lamp If in doubt install custom coated gobos with the more reflective side towards the lamp or consult your Martin dealer or gobo supplier More reflective side towards Less reflective side away from lamp lamp SX a gt To minimize the risk of gobo The less reflective side of a overheating and damage installa coated gobo will absorb less heat coated gobo with the more if it faces away from the lamp reflective side facing towards the lamp Service and maintenance 31 32 To determine which side of a gobo is coated hold an object up to it On the uncoated side there is a space between the object and its reflection and the edge of the gobo can be seen when looking through the glass Uncoated side Coated side Mirror removal It is possible to remove the moving mirror without disturbing mirror calibration if you remove the two screws holding the mirror mounting plate and leave the alloy mounting disc on the
29. he slave fixtures Set only 1 fixture on the link as master damage can occur if 2 masters or a master and a DMX controller are linked Setting up synchronized operation To set up Mania SCX600 700s for synchronized operation 1 Ensure that all slave fixtures are in DMX mode 2 Select one fixture to be the master and set it to stand alone auto trig or music trig mode see Selecting DMX music trig or auto trig operating modes on page 15 3 When slave fixtures receive signals from the master they will automatically begin operating in slave mode The Data LED on their control panels will light to show that they are receiving control data Fixtures return to their DMX auto trig music trig settings when powered off and on so you should only need to set fixtures as masters slaves once Mania SCX600 700 user manual DMX controller operation Setting DMX mode 1 or 2 Two DMX modes are available DMX mode 1 normal and DMX mode 2 extended Mode 2 uses four extra DMX channels Two of these channels allow you to select pre programmed pan tilt and effects macros and two channels allow you to set the speed of pan tilt and effects movement from the DMX controller The Mania SCX600 700 is supplied in DMX mode 2 The Mania SCX600 uses 7 channels in DMX mode 1 and 11 channels in DMX mode 2 The Mania SCX700 uses 6 channels in DMX mode 1 and 10 channels in DMX mode 2 To toggle between DMX modes 1 and 2 1 Apply power
30. ink P N 11820008 L type 5mm Allen P N 50520615 User manual nnb dale weed el be baled eee P N 35000169 Adjustable U bracket Mania SCX600 long life 250 W halogen lamp installed Mania SCX600 3 15 AT 5x20 mm main fuse installed P N 05020043 Mania SCX700 long life 150 W discharge lamp Mania SCX700 2 AT 5x20 mm main fuse installed P N 05020009 Included items US models 2 meter 6 5 ft US AC power cable 18AWG US male connector UL approved 5 meter 16 4 ft RS 485 XLR cable for datalink P N 11820008 L type 5mm Allen P N 50520615 3 15 AT main fuse installed P N 05020043 User manual sasis neret me 35000169 Adjustable U bracket Mania SCX600 long life 250 W halogen lamp installed Mania SCX600 3 15 AT 5x20 mm main fuse installed P N 05020043 Mania SCX700 long life 150 W discharge lamp Mania SCX700 3 15 AT 5x20 mm main fuse installed P N 05020043 Accessories Philips ELC 10H 24 V 250 W halogen lamp SCX600 P N 97000109 Philips MasterColor CDM SA T 150 W discharge lamp SCX700 P N 97010111 Osram HSD 150 70 150 W discharge lamp SCX700 P N 97010117 DMX termination plug end of link XLR male P N 916130
31. ion 16 DMX controller operation 17 Focus adjustment ir ayuy Eee XS i eee Be We ena 20 Adjusting music level sensitivity 20 Control panel 21 Movement 21 Mania SCX700 dimming 21 Information readouts 21 Manual control 22 Effects test eu bec ir ete dens 23 Upload mode 23 Service and maintenance 24 SGX600 lamp sn ndi ER REI ELI uid 24 SCX 00 lamp deae RU REX ate RESET MER 26 Ie uu p kG Uae 27 Replacing the mainfuse 28 Replacing a color filter 29 Rotating goDOS xe eee eer eer IRI 30 Mirror removal 32 Error messages 32 Software uploads 33 Troubleshooting 34 SCX600 DMX protocol 35 SCX700 DMX protocol 38 Controlimenus 4 55 sein RR ORE HER ET CELERE 41 Circuit board layouts
32. le available from your Martin dealer P N 11820005 3 If you intend to run fixtures in master slave operation insert a female DMX termination plug P N 91613018 in the first fixture s data IN Socket Mania SCX600 700 user manual 4 Plug a data cable into the OUT socket of the first fixture and the IN socket of the next one Continue connecting up to 32 fixtures output to input 5 Terminate the link by inserting a male termination plug P N 91613017 into the data output of the last fixture A termination plug is simply an XLR connector with a 120 Ohm 0 25 W resistor soldered across pins 2 and 3 Installation 13 3 OPERATION Note 14 The Mania SCX600 700 is supplied in DMX mode with its DMX address set to 1 If want to operate the fixture without a DMX controller you need to set the fixture to stand alone music trig or auto trig mode before use see Selecting DMX music trig or auto trig operating modes on page 15 Getting started Powering on Once the Mania SCX600 700 is correctly and safely installed power on at the fixture s power on off switch The fixture will start up and reset The display will show the following messages 1 2 Fixture name 3 Software version number 4 RST If the fixture resets successfully it will display either its DMX address SA M stand alone music trig mode or 5H R stand alone auto trig mode If any other message is displayed the fixture has detected an er
33. motor shaft undisturbed see illustration Error messages In the event of an internal error the following messages will appear in the digital display CDER Color wheel timeout GOER Gobo wheel timeout On the Mania SCX700 an additional message will be displayed in the event of an error RBER Rotating gobo timeout Mania SCX600 700 user manual If one of the above error messages is displayed try powering the fixture off and then on again to reset it If the problem persists contact your Martin dealer On the Mania SCX700 the message will be displayed if you douse the lamp via DMX and then try to restrike it within eight minutes Software uploads It is possible to upload new software to the Mania SCX600 700 via the DMX IN connector using for example an uploader such as the Martin MP 2 Uploader or a PC using a Martin DABS interface device and a suitable application such as the Martin Software Uploader The latest version of the Mania SCX600 700 software and the Martin Software Uploader are available from the Support area of the Martin website at http www martin com To prepare the Mania SCX600 700 to receive new software select in the control panel then follow the instructions in the uploader user manual or help files If the fixture will not accept a software upload as described above it can be forced to accept an upload by setting it to hard boot mode To do this hol
34. ne DMX universe Apply power to the fixture and wait while it resets Press Menu to enter the main menu Select HddF using the Up and Down buttons Press Enter Select an address using the Up and Down buttons Press Enter Press Menu to return to the main menu Cc nm Fixtures remember their DMX address when they are powered off and on DMX control options See the DMX protocols starting on page 35 for an overview of DMX commands and channels In DMX modes 1 and 2 the following functions can be controlled Reset All effects can be reset to their index positions from the controller using channel 1 The reset command must be sent for 5 seconds before it takes effect When a fixture is reset via DMX RST appears in its display Dimming and blackout Both the SCX600 and SCX700 can be blacked out using the shutter on channel 1 The shutter can also be set to music triggered operation The Mania SCX600 can be dimmed from 096 blackout up to 100 intensity using channel 2 The Mania SCX700 can be dimmed from 0 to 10096 on channel 1 if PER gt INT is set to ON in the control menus Note that to douse the Mania SCX700 s lamp a DMX value from 240 to 247 must be sent on channel 1 for at least five seconds If you douse the lamp you must wait eight minutes before restriking Color wheel position and rotation The color wheel features 9 full color filters plus white no filter The wheel can be
35. obo rotation select gobo set movement on channel 4 64 71 25 27 Gobo 1 Parasol twist 72 79 28 30 Gobo 2 Plaid dream cyan B20 80 87 31 33 Gobo 3 Cartwheel 88 95 34 37 Gobo 4 Plaid dream think pink B12M 96 103 38 40 5 Spiral galaxy 104 111 41 43 Gobo 6 Moons blue 04 112 127 44 49 Gobo 7 Radial burst Gobo shake 128 143 50 55 Gobo 1 shake fast gt slow 144 159 56 62 Gobo2 shake fast slow 160 175 63 68 3 shake fast gt slow 176 191 69 74 Gobo 4 shake fast slow 192 207 75 81 Gobo 5 shake fast gt slow 208 223 82 87 Gobo 6 shake fast slow 224 239 88 93 Gobo 7 shake fast gt slow Music triggered gobo chase 240 245 94 96 Fast 246 250 97 98 Med 251 255 99 100 Slow 4 Gobo indexing angle gobo rotation movement music trig gobo rotation Gobo indexing angle select gobo on channel 3 0 255 0 100 Indexing 0 395 Gobo rotation set movement select gobo on channel 3 0 7 0 2 Stop 8 77 3 29 Rotation CW slow fast 78 147 30 57 Rotation CCW fastslow 148 153 58 59 stop 154 223 60 87 Rotation CW slow fast 224 239 88 93 Rotation shake Music triggered rotation 240 245 94 96 Fast 246 250 97 98 Med 251 255 99 100 Slow Pan 5 0 255 0 100 Left right 128 neutral Tilt 0 255 0 100 Down up 128 neutral SCX700 DMX protocol 39 Channel Value Percent Function 7 Pan amp tilt macros DMX mode 2 only 0 15 0 5 No Macro 16 31 6 11 Macro 1 32 47 12 18
36. one 13mm hole in the top of the U bracket 4 Ensure that the structure used to support the fixture can support at least 10 times the total weight of all installed fixtures clamps cables auxiliary equipment etc 5 Install a safety wire that can hold at least 10 times the weight of the fixture through over the support and through a safety wire attachment point next to one of the swivel locks on the fixture see illustration Do not simply attach the safety wire to the mounting bracket as this will leave the fixture unsecured Safety wire attachment point 6 Loosen the swivel locks and tilt the fixture to the desired angle Turn the swivel locks clockwise to tighten Check that both swivel locks are tight and that the fixture is securely clamped in position Creating a data link for DMX or synchronized operation You need a serial data link to run light shows on one or more fixtures using a DMX controller or run synchronized light shows on two or more fixtures master slave operation Fixtures on a serial data link must be daisy chained in one single line max 500 meters 1640 ft long with max 32 fixtures If you wish to Installation 11 12 exceed 32 fixtures or 500 meters or to add branches use an optically isolated amplifier splitter such as the Martin RS 485 Opto Splitter P N 90758060 Reliable data connection requires suitable cable Standard microphone cable cannot transmit DMX data reliably
37. onnect them directly together until normal operation is regained Have defective fixture serviced by a Martin technician A number appears in display and fixture will not run a stand alone light show Fixture is set to DMX mode and is displaying its DMX address Use control panel to change fixture from DMX to stand alone auto trig or music trig An effect fails to reset correctly The effect may require mechanical adjustment Contact Martin technician for service Lamp cuts out intermittently or burns out too quickly Fixture is too hot Allow fixture to cool Check that there is free airflow around the fixture Check and if necessary clean fan and grills Fixture does not respond correctly to music beat in music trig mode Music level sensitivity is incorrectly adjusted Use control panel to adjust sensitivity until fixture responds satisfactorily SCX700 Impossible to restrike lamp after dousing via DMX 8 minute restrike protection delay activated Mania SCX600 700 user manual Wait 8 minutes before restriking a hot discharge lamp 7 SCX600 DMX PROTOCOL Channel Value Percent Function 1 Shutter strobe effect music triggered shutter reset 0 7 0 2 Shutter closed 8 15 3 5 Shutter open 16 95 4 37 Strobe slow fast 96 103 38 40 Shutter open 104 151 41 59 strobe slow fast 152 159 60 62 Shutter open 160 199 63 78 Music triggere
38. positioned to give full colors scrolled to give split color effects rotated continuously in either direction with variable speed or set to music triggered operation Gobo wheel position and rotation The gobo wheel features 7 rotating gobos and an open position Rotating gobos can be selected shaken at different speeds and set to music triggered operation Rotating gobos Speed and direction of gobo rotation can be controlled Gobos can also be set to shake or set to music triggered operation Mania SCX600 700 user manual On the Mania SCX700 gobo angle can be indexed i e set to a precise angle Pan Pan with approx 198 available Tilt Tilt with approx 72 available In DMX mode 2 the following additional functions can be controlled on four extra channels Macros A range of factory set macros are available with macros that control pan tilt and macros for the other effects on two separate channels The macros are professionally designed programs that use all the fixture s effects to give complete light shows with minimal user programming required Pan tilt speed and effects speed The speed at which the fixtures s mirror pans and tilts and the speed at which effects change can be adjusted on two extra channels Selecting a speed allows you to adjust fade times when using DMX controllers that do not feature fade time programming a fade time is the time taken for effects to change from one scene to the next If you s
39. r The SCX600 displays the number of times the fixture has been powered on since the counter was last reset The SCX700 displays the number of times the lamp has been struck since the counter was last reset Press Enter to display Press Up for 5 seconds to reset the counter to zero each time you install a new lamp INF U STIMESLSTASTU TL displays the total number of start ups SCX600 or lamp strikes SCX700 since manufacture Software version INF 0 1 ER displays the fixture software version number The software version is also displayed briefly when the fixture is powered on Manual control The manual control menu MHN provides commands for resetting the fixture R5 T as well as striking the lamp L GN and dousing the lamp LoF F It also permits you to position and move individual effects Mania SCX600 700 user manual Effects test The test sequence T SEG RUN runs through all effects to provide quick check of fixture performance Upload mode The upload mode command U T IL gt UPL prepares the fixture for a software upload see Software uploads on page 33 Control panel 23 5 SERVICE AND MAINTENANCE Warning Important Important 24 The Mania SCX600 700 requires simple routine maintenance The maintenance schedule depends heavily on the operating environment please consult a Martin service technician for recommendations Any service procedure not described here should be r
40. re opening the fixture or removing the lamp Do not modify the fixture or install other than genuine Martin parts Do not operate the fixture if the ambient temperature Ta exceeds 40 104 F Protecting yourself and others from injury due to falls When suspending the fixture above ground level verify that the structure can hold at least 10 times the weight of all installed devices Verify that all external covers and rigging hardware are securely fastened and use an approved means of secondary attachment such as a safety cable Block access below the work area and work from a stable platform whenever installing or removing the fixture Mania SCX600 700 user manual 2 INSTALLATION Warning Important AC power The Mania SCX600 700 is supplied set up to match local voltage and frequency settings The factory setting is shown on the serial number label For protection from fire and electric shock the fixture must be grounded earthed The power supply must have overload and ground fault earth fault protection Check that power cables are undamaged and rated for the current requirements of all connected devices before use Ensure that the fixture s voltage setting matches your local AC power supply before applying power Do not connect the fixture to a dimmer system as this will cause damage that is not covered by the product warranty Mania SCX600 power settings Mania SCX600 models can be set
41. rom power and data and Fuse holder contact a Martin service technician Mania SCX600 700 user manual Replacing a color filter The color filters fitted to the Mania SCX600 700 are standard interchangeable items Wear cotton gloves when changing filters to avoid contaminating components with grease from your fingers To replace a filter 1 Disconnect the fixture from power and allow to cool for 20 minutes 2 Loosen the lamp cover release thumbscrew and open the cover 3 See illustrations above The color wheel is in front of the lamp Pull gently on the filter A and slide it up and out of the wheel B 4 Slide the new filter down onto its clip 5 Check that the new filter is held securely and replace the lamp cover before reapplying power Service and maintenance 29 Rotating gobos The rotating gobos fitted to the Mania SCX600 700 are standard interchangeable items A range of replacement 6 gobos is available from your Martin dealer SCX700 gobos viewed from lens side 30 Mania SCX600 700 user manual To replace a gobo 1 Disconnect the fixture from power and allow to cool for at least 20 minutes 2 Loosen the lamp cover release thumbscrew and open the cover on its hinge 3 See illustration on right Pull the gobo gently away from the gobo wheel and slide it up and out of the wheel 4 Slide the new gobo in and push gently towards the wheel to clip it into place JEZ h Ass Check t
42. ror see Error messages on page 32 If this occurs switch off wait a few seconds and switch on again If the error message appears again consult your Martin dealer Control panel and menus You can set the Mania SCX600 700 s DMX address modify the fixture s personality and control effects manually using the menus in the control Mania SCX600 700 user manual panel See also the overviews printed on the fixture and in Control menus on 41 Power indicator LED D VAN VN PN VAN eq e Menu Enter Up Down Control buttons Data indicator LED To enter the menus press the Menu button Use the Up and Down buttons to scroll within a menu To select a function or submenu press the Enter button To exit a function or menu press the Menu button Music trig auto trig and DMX modes The Mania SCX600 700 has three main operating modes Stand alone music trig mode In this mode lighting effects are triggered by music intensity Multiple fixtures can be synchronized if one master fixture is set to stand alone music trig mode and the other fixtures are set to DMX mode Stand alone auto trig mode In this mode the fixture runs a factory set dynamic light show that uses all the fixture s effects in a random program Multiple fixtures can be synchronized if one master fixture is set to stand alone auto trig mode and the other fixtures are set to DMX
43. t invert PSET MDd 1 DMX mode 1 normal MOde DMX mode 2 extended DMXc controlled operation slave NURM fixture x Stand alone auto trig operation auto trig MUdE SR R master fixture SA M Stand alone music trig operation music trig master fixture DF F Dimming disabled SCX700 only PER INT mE DN Dimming enabled SCX700 only T TL total hours of operation since manufacture HRS RSE T resettable counter Press Enter to display hours of operation since counter reset To reset to zero press Up for 5 seconds TOTL total hours of lamp operation RSET resettable counter Press Enter L HR to display hours of lamp operation since TIME counter reset To reset to zero press Up INFO for 5 seconds SCX600 T TL total number of startups power ons SCX700 T L total number of lamp L 5 T strikes RSET resettable counter Press Enter to display number of startups lamp strikes since counter reset To reset to zero press Up for 5 seconds VER CPU software version number Table 2 Control menu Control menus 41 RST Reset fixture L ON Lamp on Loff Lamp off OPEN Open shutter CLOS Close shutter SHUT STRF Shutter strobe fast STRM Shutter strobe medium STRS Shutter strobe slow dIM 8 255 Dimmer OPEN Color wheel in open position 1 Color wheel positions 1 9 MAN CW F Clockwise rotation fast COL
44. to the fixture and wait for the fixture to reset 2 In the control panel press the Menu button Then use the Up and Down buttons to scroll to P SET personality setting and press Enter 3 Use the Up and Down buttons to scroll between MB d 1 and MO d and press Enter to save your setting Setting DMX addresses If you use a DMX controller you need to set the DMX address for each fixture on the fixture s control panel The DMX address or start channel is the first channel used to receive instructions from the controller For individual control each fixture must be assigned its own DMX address and control channels For example if an SCX600 is set to DMX mode 2 and you give it DMX address 101 it will use channels 101 111 inclusive Channel 112 is available for the next fixture An SCX700 in DMX mode 2 with address 101 will use channels 101 110 inclusive Channel 111 will be available for the next fixture Fixtures with the same DMX address will receive the same instructions and behave identically Two fixtures with the same DMX address can be set up so that one pans as a mirror image of the other To achieve this use the settings in the control menu to invert the pan on one fixture see Movement on page 21 Operation 17 18 The default factory set DMX address is 1 To set a fixture s DMX address 1 Decide on suitable DMX addresses for all the fixtures on the data link 512 channels are available in o
Download Pdf Manuals
Related Search