user manual - ARMON products
Contents
1. every arm In the figure below you can see the amount of force that is given by the Edero per step Force gram 1 0 a e p an o 3736 4445 EE Adjust the level of weight compensation by following these steps 1 Pull the upperarm upwards in the direction of the green PULL arrow UPPERARM 2 Move the ring in the direction of the green arrows and UPWARDS place it in the step of your choise 3 Let go of the upperarm The Edero is ready for use ADJUST RING Placing the arm Place the arm in the brace in the following way e The underarm should lay in the brace e The upper arm should be placed against the upper arm support not far above the elbow e The elbow should be free e The upper arm support consists out of non allergic rubber with a stainless steel frame in it that can be bent in any direction so that it is the most comfortable for the user Serial number Every Armon Edero has a unique serial number This number can be found on the underside of the upperarm of the Edero SERIAL NUMBER SERIAL NUMBER Usage safety warranty and cleaning instructions Usage The Armon Edero is an arm support and should only be used to support the weight of an arm with a maximum weight of 5000 gram per arm Safety e The arm support may only be used for the proposed purpose Any type of use which is not specified in this manual will be considered as improper use The customer is solely responsibl2. 2008 The object of the declaration described above meets the demands for CE labeling Medical Device Class Microgravity Products B V Tel 31 010 4714187 Kiotoweg 738 3047BG Rotterdam www armonproducts com The Netherlands info armonproducts com
3. e for material damage and injury of persons resulting from improper use Armon Products will not be liable under any circumstance e Assembly commissioning and maintenance should only be carried out by trained specialists e Inany circumstance do not open the housing of the arm support Warranty is void in such case e Do not use the arm support in evironments exposed to corrosion hazards e Protect the arm support against sand vapours and dust Warranty e Warranty claims shall be voided in case e Our conditions in the operating manual are ignored e The appliance is used outside the described uses e Any part of the appliance is modified or opened e The appliance is impoperly set up or incorrectly electrically connected Cleaning The Armon Edero the brace and the accessories can be cleaned with a wet cloth The Armon Edero the brace and accessories are splash proof When cleaning do not use any chemicals or solvents Technical data Weight Edero base links Edero brace 1800 gram Weight compensation range 600 till 4800 gram Housing size WxDxH 17x10x85 cm Housing material Die cast aluminum Unique identification of the object E2015100 E2015101 E2015102 E2015200 Description of object Fully mechanical arm support as in conformity with CEN TC 293 WG 5 The object of the declaration described above is in conformity with the relevant Community harmonization legislation Directive 93 42 EEC EN ISO 22523 2006 EN 1041
4. he bearings of the links over the pin of the Table Clamp in the direction of the green arrow 4 ATTENTION Make sure the pin goes all the way through the links The angled top part of the pin must come out above the links like in the picture below If this is not done correctly the bearings might break 5 Place the base of the Edero on top of the other end of the links You do this by sliding the pin of the base of the Edero into the bearings of the links in the direction of the green arrow 6 ATTENTION Make sure the pin goes all the way through the links The angled bottom part of the pin must come out underneath the links like in the picture below If this is not done correctly the bearings might break ANGLED BOTTOM PART LINKS OF THE PIN How to attach the brace to the Armon Edero Follow these three steps 1 2 The upper arm should slide into the slot of the hook of the brace in the direction of the green arrow WASHERS UPPER ARM UPPERARM 3 Pull the clip inwards in the direction of the green arrow to slide the hook of the brace between the two washers of the upperarm 4 Make sure the clip locks over the head of the bolt The head of the bolt should be visible through the clip PULL CLIP MAKE SURE THE CLIP LOCKS OVER THE HEAD INWARDS OF THE BOLT E g P g Adjusting the force You can adjust the force of the Edero in 12 steps this called the adjustment range to compensate the weight of
5. user manual ARMON EDERO The Armon Edero is a non electric fully mechanical dynamic arm support as in conformity with CEN TC 293 WG 5 The Armon Edero can compensate an arm weight from 900 gram up to 4800 gram The weight compensation is adjustable in 12 steps of approximately 350 gram per step It is possible to mount the four different types of Armon braces The Edero is available in the colors black RAL 9005 and white RAL 9010 The Armon Edero consists mainly out of die cast aluminum Weights Edero Table Clamp Edero Brace 2730 gram Table Clamp 930 gram Complete Edero set in box 3400 gram The object of the declaration described above is in conformity with the relevant Community harmonization legislation Directive 93 42 EEC EN ISO 22523 2006 EN 1041 2008 The object of the declaration described above meets the demands for CE labeling Medical Device Class How to set up the Armon Edero ARMON UPPERARM BASE TABLE CLAMP The Edero will be delivered in a box outer dimensions w h 49x29x17 cm like in the picture below 1 Begin with placing the Table Clamp ona solid horizontal surface By turning the knob you can loosen or tighten it Make sure the Table Clamp is tightened firmly before proceeding with placing the links PARKING HOOK TABLE KNOB MIDDLE PART OF LINKS TO U THE OUTER SIDE 3 Place the links on top of the pin of the Table Clamp You do this by sliding t
Download Pdf Manuals
Related Search