User Manual - Dolphin-3
Contents
1. 2005 copyright P N82605002C need to be repaired or contact the power system supplier detection area is non anti pests area the place that pests can climb up directly of the detector is 2 2 2 4 meters can Anti pests 3 3 ustrated Installation Procedure 3 3 1 Disassemble unit C Move the cocer to the E Remove the PCB D Loose the screw volitant top and remove it A Loose the screw B Pull out the bottom of the cover 3 3 2 Mount base A Mark the drilling points 1 8 2 4m 6 8ft above ground and drilling the wall B Route the wires into the base VIA the rear channel Surface C Insert two dowels and mount attach the base to the wall with two screws D Insert the bottom edge of the large PCB under this TAB amp Press the top edge in Single side 45 angled side 3 4 MW sensitivity adjust MW sensitivity adjust C Turn MW scale regulating wheel to the anticlockwise 7 o Jo direction and adjust the MW ee eo amp detection scale to the Min During 7 walking test adjust the wheel to clockwise direction and gradually increase the MW detecting scale till the whole protection area is covered Notice Adjustment of MW detection scale should meet the size of protected room 3 6 Product operates its relays and LED indicators according to the dete2. motion test from contrary directions in order to confirm the boundary of two sides Make confirmed that detection center pointing to the center of protected area 4 Away from the detector 3 to 6 m raise slowly your arm and reach into the detection zone mark the lower limit of PIR detection Do the same step to confirm the upper limit 5 the center of detection zone should not uphill incline To obtain a good detection range please adjust the vertical detection range en sure the detector is in a correct position 6 After MW sensitivity or detection angle are adjusted walking test must be performed according to the above steps The test procedure for masking detection Anti masking Ina distance of about 10 cm from the detector s front place a white paper or any other object The necessary reaction of the detector The Yellow LED will blink immediately After 2 minutes the asking Relay will activate All time when an object blocks masks the near field of view of the detector the masking relay and the Yellow LED will activate The test procedure for Case shifting detection Shake the detector If it fixed to a wall knock on the detector s case by ascrew driver The necessary reaction of the detector The Masking Relay will activate for 2 second The Green LED will activate shortly upon every knocking Important mention Motion test shall be performed at least one time each week in order to guarantee that each detec
3. 4 Special comments Even the most sophisticated detcetors can sometimes be defeated or may fail to warn due to DC power failure improper connection malicious mask ing of the lens tampering with the optical system decreased sensitivity in ambient temperatures near that of the human body and unexpected fail ure of a component part The above list includes the most common reasons for failure recommended that the detector and the entire alarm system be ch ecked weekly to ensure proper performance An alarm system should not be regarded as a substitute for insurance Home amp property owners or renters sh ouldbe prudent enough to continue insuring their lives amp property even though they are protected by an alarm system Installation Guide of FT 85 PIR amp MW Intelligent Intrusion Detector This device has been tested and found to comply with the limits for a Class B digitaldevice pursuant harmful interference in residential installations This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the ins tructions may cause harmful in terference to radio and t elevision reception However there is no guarantee that interference will not occur in aparticular installation If this device does cause such interference which can be ver fied by turning the device off and on the user is encouraged to eliminate the interference by one or more of the followingmeasures Incre
4. ase the distance between the device and the receiver Connect the device to an outlet on a circuit different from the one that supplies power to the receiver Consult the dealer or an expericnced radio TV technician WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment 5 Solution of usual problem _ In alarm area have walk test but no alarm output i i i To check if the control main Al LED light OK To open the detector OK To disconnect the alarm OK houl alarni sianal __ cabin check the relay _ output wire from the terminal gt board faulty If yes contact output contact is open or not check if there is short circuit the supplier of mainboard NG NG Please send E mail export meiantech com for Tech Support NG gt Please clear the trouble of short circuit d Alarm LED shut off OK To check the detector OK IToresetthe detector check OK without alarm signal working yoltageisat gt the LED lights up or not Repeat walk test output 9 16V DC or not NG To adjust the working voltage of OK the detectorto 9 16 V DC False alarm If there is strong cold or hot airflow in the det
5. ct 1999 5 EC necessary items and rules and also coherent to the main spirits of radio and telecom terminal equipments on March 9 1999 The device also reaches the Canadian standard RSS 210 It can be used indoor and outdoor which can reach its maximum prote Alarm Mask and Tamper Alarm Output Solid state relay N C amp N O up to 100mA 30V 300 Tamper Contacts N C 50mA resistive 30 VDC 0 2 4 6 8 10 12m Installation height do not at 1 8 2 4m To adjust installation height according ction and avoidance of above interference to DC9 16V at certain redundancy Especially less than 1 8m to the instruction To adjust the sensitivity and repeat walk OK gt The detector s sensitivity is too high _ Unstable installation base test If there is high voltage electric field near To adjust the position of installation to y NG to the wire of detector make sure it is far away from the high voltage electric field To select new installation base choose solid foundation Wire terminal bad connected with high resistance Wire terminal well connected Output of power supply not good not gt ge ies Change the power supply or repairing good filtering With electronic power on no LED signal OK Please send E mail Ifthe LED switch NG _ Check the power OK Check if the
6. ction angle is largest Lower section sensitivity is low Pet immunity up to 20Kg At this angle detection angle is smallest sensi tivity is highest no pet immunity function 3 7 Extremity connection titi area EOL Alarm control panel resistor ease Ta Alarm area pox Tl or Tamper MW mask y Alarm area 2 3 4 45 6 7 8 9 EOL TAMP C MASK CO NO NC COM V V its ae resistor SSP Sss Ba TT When control panel is set to extremity operation mode FT 85 PCB please try extremity resistor 3 8 Wiring terminal specifications Termindls8 9 Indicated on the circuit as These are the 12V DC power supply inputs Terminals 5 6 7 Indicated on the circuit as ALARM C N C N O Represent the contacts of the Alarm Relay C N C Normally Closed C N O Normally Opened Upon any human movement detection the relay s contacts are Opened for two seconds Terminals 2 3 Indicated on the circuit as MASK Represent the contacts of the Masking Relay which normally are in cl osed state N C Closed state N C If an object blocks masks the near field of view of the detector for more than 2 minutes the green LED will glow constantly and the MASK elay will operate for at least 2 seconds and all time the masking exists Terminals 1 2 Indicated on the circuit as TAMP Represent the contacts of the built in TAMPER
7. ction nature as following TYPE OF DETECTION LED INDICATORS RELAY STATUS Alarm true motion Red Green ALARM relay will activate detection blinking together for 2 seconds PIR detection Green NO relay will operate OR mode Red NO relay will operate During masking only MW Red Green detection AND mode blinking together ALARM relay will activate During masking for 2 seconds only If masking exists for more than 2 minutes the green LED will glow constantly and the MASK relay will operate for at least 2 seconds Yellow and all time the masking exists Blinking Anti masking detection Anti case shifting MASK relay will activate detection for 2 seconds 3 5 DIP Switch Adjustment ON DIP 12345 NO Function OFF ON 1 LEDs OFF ON 2 PIR Sensitivity LOW HIGH Anti masking amp 3 Anti case shifting LOW HIGH Sensitivity Microwave AND Detection Comb Microwave PIR OR Just 4 ination Type AND PIR Microwave During masking only y Anti caseshifting ENABLED DISABLED Enabling 3 9 Setting of detection angle When multi function bracket is used optional installati on shad refer to the right dia gram adjust installation ang le in order to get needed det ection scale and function At this angel sensitivity is in middle Pet immun ity up to 10Kg animal animal At this angle dete
8. ection area such as from air conditioner heater etc To get rid of cold or hot airflow or cha Check the voltage of power OK nge installation environment supply DC 9 16V NG If there is animal more than 20Kg in the To remove the over 20kg animal detection area To adjust the power supply voltage 1 Introduction FT 85 is virtually the best outdoor indoor motion detector ever presented for industrial commercial and residential security FT 85 has a m as sive aesthetic design and combines the technologies of passive infrared and Microwave as well It is waterproof and all weather resistant FT 85 also al erts in any attempt to damage disable its operation Ft 85 combines a variety of detection techniques that enable it to work in the most difficult environmental conditions and where high security is required while maintaining unprecedented immunity to false alarms The two synchronized PIR sensors produce a three dimensional thermal imaging of the protected area Combining the fourth dimension ad microwave scanning contributes to an amazing detection capacity and at the same time it also increases the reliability and immunity to false alarms Using this technique allows high sensitivity level adjustment in both detection technologies without the need of pulse count In addition to an unprecedented amazing and reliable detection skill FT 85 is equipped with unique protection mechanisms against any attem
9. is Necessary to allow the detector study and analyze automatically the environmental conditions of its protected area The study procedure to be performed in three cases 1 Upon connecting the power supply to the detector 2 Upon the position of DIP switch number 3 Masking detection Sensitivity is changed 3 Upon relocation of the internal unit of the detector The study procedure in the first amp third case Close immediately the detector s case within 15 seconds Maximum Keep away at least 0 5 meter from its front until the study Procedure finished about 30 seconds As an indication for the study procedure the Red Yellow LEDs will blink rapidly once the procedure begins and ends The study procedure in the second case Change the position of DIP switch number 3 for about one second and switch it back to the original place Close immediately the detector s case within 15 seconds maximum Keep away at least 0 5 meter from its front until the study procedure finished about 30 seconds As an indication for the study procedure the Red Yellow LEDs will blink rapidly once the procedure begins and ends 3 12 Perform motion test to the detection area 1 Start the test at least 2 minutes after power supply 2 Crossing to any direction of the detection area your walking with 0 75m s will cause the Red amp Yellow LED indicator to light for 2 3 seconds refer to the right diagram 3 Perform
10. pt to damage or to disable its operation These following protection mechanisms always work weather the alarm system is Armed or Disarmed 1 Forntal Anti masking by a continuous active infrared scan against masking the near field of view of the detector Detects even transparent objects such as clear glass plastic bags or transparent spray of any king 2 Imposes OR mode in distress If from any reason the PIR detection channel is neutralized for example the detector front was masked the Micro wave detection channel will guard the protected area 3 Anti case shifting by inertial switch that alerts if someone shifts moves or turns the detector 2 ification Spec cantons Top View Mounting Models Surface or corner at the height of 1 8 to2 4m FT 85 Note Base allows single sided corner mount at 45 to wall FT 85DMF FT 85DMT Accessories BR 1 Surface mounted swivel bracket adjustable 30 Detection Ratige lam down and 45 left or right Input Voltage 9 to 16 VDC Current Drain About 65mA 12 VDC Environment Operating Temperature 10 Cto50 C 14 Fto 122 F PIR Section Lens Date Storage Temperature 20 Cto 60 C 4 Fto40 F NO of Curtain Beams J Anti white light gt 9000 LUX 11 11 9 2 62 Typical Physical Max Coverage 12 12m 90 Size H W D 176 83 66 mm Tripping Indication Sise View 3 colour lights for about 30 seconds 3 E 3 This device is coherent to Europe parliament dire
11. switch which are normally in closed state N C The contacts will open upon the detector s case is opened Terminal 4 Indicated on the circuit as CO This terminal to be used if you wish to get a report from the detector s memory whether it has detected human movement during the armed period This terminal should get indication from the alarm system s control panel whether it is in Armed or Disarmed state If OV received the detector understands lt If 12V or no voltage at all received the detector understands That the alarm system is Disarmed How to draw and display the detector s memory If the detector has alerted during the armed period Than upon switching the alarm system from Armed to Disarmed mode the Red LED will be activated for 30 minutes 3 10 Adjust the PCB When detector is installed in different environment and places you can solve the problems you meet th rough adjustment of the position of PCB eg when detector installed on 1 1 m you need to adjust the marks on PCB to 1 1m position And also as you install the detector to t3 1 m adjust the PCB to 3 1 m usually it is 2 1m ie at the middle s SS Sos Ky 3 11 Preparing the Anti Masking channel for work In order to enable the masking detection to operate properly it
12. tor can keep excellent function A
13. voltage is at export meiantech com for Tech Support off or not input connection gt DC9 16V or not accord is correct or not ing to the manual NG no If the power supply OK circle is open Check power supply we system at DC9 16V gt To connect power supply circle correctly ox The wire length of power supply is exceeded or wire diameter is too small Please NG change into fitted wire Open the LED switch Ensure power input connection right Short circle or wrong earthconne OK A NG ction in power supply get rid of the Disconnect the terminal to c Power supply system has problem Mask Output N C up to 100mA 30V 300 3 Installation 3 1 General Guidelines iz Don t face cold Don t face the sun or heat directly shine directly Wire connection or detector can t be near to high pressure cable Don t install ona Don t face metal wall unstable base 3 2 Anti pests installation T AN lt j a o 2 Bo jn The upper part of the Never face the detector to Anti pests weight lt 20Kg The installation height mistake heck the power supply system
Download Pdf Manuals
Related Search