Hall Research UH-1D Manual
Contents
1. further assistance ns gt HDMI over Single Cat6 Extender kit Use only regulated 5v DC supply center positive as supplied with the unit Ow S v 3 0 Installation The following diagram illustrates a typical setup Note that the IR cables are optional and should be ordered separately LOCAL DISPLAY a4 REMOTE DISPLAY IR TRANSMIT i HDMI SOURCE pitt acti pr RECANE Installation diagram showing all possible connections 3 1 Sender Connections The input side of the sender unit is shown below Connect the video source to the connector labeled HDMI IN Optionally connect a local TV or another Sender unit to the connector labeled HDMI OUT Video input and output on the Sender Connect a Category 5e 6 cable to the opposite end s RJ45 connector and plug in the included power supply 3 2 Receiver Connections The output side of the receiver unit is shown below Connect the video source to the connector labeled HDMI OUT Optionally connect any audio device to the analog or digital audio outputs 5 The default EDID in the Sender device reports the following supported audio formats to the source PCM 2 channel at 32KHz 44 1KHz and 48 KHz 16 20 or 24 bits If the source pays attention to the EDID and sends 2 channel audio the analog audio output will have 2 channel stereo outputs However if the source decides to send multi channel compressed bitstream audio such as Dolby or DTS t2. HALL USER S MANUAL RESEARCH UH 1D HDMII over Single Cat6 Extender kit Extends uncompressed Full HD 1080p to 130 ft 40m Provides local HDMI loop output on the transmitter EDID learn button to store and emulate EDID from any display 3 5mm analog and RCA digital audio outputs Extends IR in both directions UMA1231 Rev n c Copyright 2015 Hall Research Inc All rights reserved 1163 Warner Ave Tustin CA 92780 Ph 714 641 6607 Fax 714 641 6698 HDMI over Single Cat6 Extender kit Table of Contents LOPO O 9 Commer enter enter nnres WPT UCI Rr nN ene eater nrTe WY EAT anTITe WOU OEIC Tn pea ree Wey EAT 3 AO TC AS acerca nt aster nen sateen A A E A E E A A eens emesis 3 21 Package Contento BE Oe ce ee 3 SO TIPS CAN ANT O a e e N e E E A 4 3 1 Sender Connections ccccescesccsccsccesceccesccscceccesceccescescescesscescescescesces 4 3 2 Receiver Connections ccccesccsccsccscceccescescescencccsceccescescescesscescescescesees 4 3 3 IR Remote Extension c cccccsccsccsccecceccescesccecccscescescescescesscescascesceees 5 AFOD O apes aE vans E E eE N EE E E EEE 6 IOS PECCATO A A ere eee eee eee 7 TRADEMARKS USED IN THIS MANUAL Hall Research and its logo FR are trademarks of Hall Research Any other trademarks mentioned in this manual are acknowledged as the property of the trademark owners FCC RADIO FREQUENCY INTERFERENCE STATEMENT This equipment generates uses and can radiat
3. ay In addition to the HDMI video output the Receiver provides both digital audio SPDIF as well as analog stereo L R outputs for connection to audio equipment The UH 1D allows connection of an IR detector and an IR emitter cable to each end This provides the ability to extend IR signals in either direction For example when an IR detector is connected to the remote Receiver and IR emitter is connected to the sender the user from the remote TV end can control the source using an IR remote IR cables are sold separately The devices have L shaped brackets on each end for easy surface mounting and they feature locking HDMI connectors to secure compatible locking cables such as Hall Research C HDMI L series cables 2 0 Features e Uses only one Cat5e 6 cable to extend HDMI without compression e Can extend Full HD 1080p to 130 ft 40m Provides local HDMI loop output on the transmitter for connection to local monitor or to another UH 1D sender EDID learn button to store and emulate EDID from any display Supports HDCP Receiver provides both 3 5mm analog and RCA digital audio outputs Can extend IR in both directions IR cables are sold separately 2 1 Package Contents 1x UH 1D S sender 1x UH 1D R receiver 2x 5vDC power supplies one for each end lx User s Manual All packages are carefully inspected prior to shipment However if you think that you are missing an accessory please contact Hall Research Support for
4. e radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio communication It has been designed to comply with the limits for a Class A computing device in accordance with the specifications in Subpart B of Part 15 of FCC rules which are intended to provide reasonable protection against such interference when the equipment is operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at their own expense will be required to take whatever measures may be necessary to correct the interference Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment eee Compliant FE Ay RAL C oe Of 8 D 1 0 Introduction The UH 1D is a member of the video over twisted pair extension line from Hall Research This economical and easy to install extension kit uses only a single UTP Cat6 cable to extend Full HD 1080p HDMI signals to over 130 ft 40m or 720p 10801 to 170 ft 52m The product is comprised of a sturdy and compact Sender and a corresponding Receiver The UH 1D offers several unique features such as a local HDMI output loop on the Sender for connection to a local monitor and EDID management capability with ability to learn and emulate EDID from any displ
5. ected TVs it maybe that the generic default EDID is not suitable for your source or TV In that case if the TV works when directly connected to the Video Source we recommend learning the EDID from your display to substitute it for the default built in EDID 4 1 Learning and Emulating EDID By default the LEARN EDID light is off This means that the unit 1s using a generic default internal EDID for the source that includes various PC and TV resolutions that the UH 1D can support If your specific TV does not support some of the resolutions that the default EDID reports to the source you can learn the EDID from the TV used by following the steps below 1 Plug the TV to the Sender s HDMI OUTPUT port the HDMI input can be left disconnected it does not matter 2 Press and hold the MODE button for 3 seconds The LEARN light will blink a few times indicating that the W mkdaiiza device has learned your TV s EDID and will stay on indicating that it is emulating the new EDID for the source LEARN MODE To go back to the default EDID press and hold the MODE button for 3 seconds Just tapping the MODE button will not change the EDID mode This design feature ensures that if a user inadvertently pushes the button the mode will not change If you try to learn EDID and a TV is not connected to the HDMI OUTPUT the unit will not learn any EDID and will continue using the default EDID The Sender will remember its EDID mode when p
6. hen the Analog output is not present In that case use the RCA digital SPDIF output which is active regardless of the audio format Video and Audio output on the Receiver Connect a Category 5e 6 cable to the opposite end s RJ45 connector and plug in the included power supply 3 3 IR Remote Extension The UH 1D allows connection of an IR detector and an IR emitter cable to each end This provides the ability to extend IR signals in either direction For example when an IR detector is connected to the remote Receiver and IR emitter is connected to the sender the user from the remote TV end can control the source using an IR remote IR cables are sold separately IR connectors on the Sender and Receiver IR Detector Cable is Hall Research P N CIR DET P2 This detector cable has a Red LED that glows when connected properly Tip Data Ring 5V Sleeve Gnd Do not substitute any other detector cable as this may not work your substitute IR detector cable may also get damaged es gt HDMI over Single Cat6 Extender kit IR Emitter Cable is Hall Research P N CIR EMT recommended you can also use CIR EMT2 Please check Hall Research website for further information 4 0 Operation The product is Plug n Play meaning that when connected as described in the previous section everything typically works with no issues If you have any issues such as no image or an image that is not centered or partially cut off etc on the conn
7. l Research Inc All rights reserved 1163 Warner Ave Tustin CA 92780 Ph 714 641 6607
8. ower is disconnected If you Exit the Learn amp Emulate mode the sender will forget the learned EDID To go back you have to Re learn the EDID 5 0 Specifications Video Standards DVI single link and HDMI compliant with HDMI 1 4 video specifications including 12 bit color depth and 3D video 4K video is not supported Signal type TMDS Connectors Locking HDMI Video Resolutions For DVI signal VGA 640x480 thru WUXGA 1920x1200 For HDTV signal 4801 through 1080p Audio Supported Formats All HDMI Embedded Audio pass through to HDMI output and Digital audio output Analog audio output only supports 2 channel uncompressed audio General Power Supply 100 VAC to 240 VAC 50 60 Hz external 5 VDC 2 6 A regulated Nominal Power Sender 3 25 watts max Receiver 2 25 watts max Temperature humidity Operating 32 to 104 F 0 to 40 C 10 to 90 Storage 40 to 158 F 40 to 70 C 10 to 90 Cooling Convection Mounting End plates have L bracket with hole for surface mounting Enclosure type Metal Steel ends and Aluminum extrusion Dimensions 1 18 H x 2 75 W x 3 85 D 30mm H x 70mm W x 98mm D Product weight Product 0 75 lb 0 35 kg Shipping 1 5 Ibs 0 70 kg Vibration ISTA 1A in carton International Safe Transit Association Safety CE EMI EMC CE FCC Class A MTBF 90 000 hours Calculated Estimate Specifications are subject to change without notice IFA HALL RESEARCH Copyright 2015 Hal
Download Pdf Manuals
Related Search