Home

"user manual"

1. uiu ODINO A3PLUS OPERATING INSTRUCTION GUI 6 5 Suction tubes Suction starts by taking the tube off the board To adjust suction use the slider a located on the tube handpiece ES NOTE when the tube is put back in place suction stops approxi mately 2 seconds later This is done to dry the suction tubes Removing the suction tubes WARNING Always wear gloves to prevent contact with infected material when removing the suction tubes Remove the suction tubes from the conveyor fittings by turning and twisting the tube fitting Detach the suction tubes from the holders by turning and twisting the tube fitting WARNING Never directly grasp the suction tube Cleaning the suction tubes As the dental units may be equipped with different suction systems liquid ring or wet air carefully follow the instructions provided by the suction system manufacturer when disinfecting the system regarding the product to be used times and directions for use WARNING For cleaning of the suction system it is recommended to use STER 3 PLUS CEFLA S C diluted in a 6 solution equivalent to 60 ml of product in 1 litre of water Disinfection Cannula holder terminals steam aut e Suction tubes soak to cold sterilize WARNING Never use procedures in which the temperature goes over 55 C with the tubes Maintenance Periodically lub
2. 40 ACCOSSOMIOS m ii 41 Operating lamp icr ctr etre 41 Monitor orilamp pole recien ei 43 Negatoscope for panoramas ai 43 Air water 230V quick connect couplers 43 Maintenance Instrument maintenatnce ioter nette 44 Draining condensatoe tee ped 44 Cleaning the surgical suction filter 44 Sutdical SUCHOL ri eere Drop ean tte tp eas 45 CATTANI surgical separator 46 CATTANI gravity amalgam separator 46 Cleaning the turbine return air filter 47 METASYS amalgam separator ern 47 DURR amalgam separator 47 Dental chair nere ia aa 47 Specifications A3PLUS CONTINENTAL dimensions A3PLUS INTERNATIONAL dimensions 50 Dental operatory maintenance plan 51 GIL A3PLUS OPERATING INSTRUCTION fonthos 1 Safety guidelines These instructions describe how to use the A3PLUS dental units correctly Carefully read and become familiar with the content of this manual before using the equipment These instructions describe all the versions of the operating units with the maximum possible accessories therefore not all the paragraphs are applicable to the unit you have purchased No part of this manual is to be reproduced stor
3. OO ODINO A3PLUS OPERATING INSTRUCTION 4 1 Safety devices The equipment is supplied with the following safety devices The floor box is equipped with a device I that immediately stops the dental chair from moving down in the presence of an obstacle and auto matically lifts it up to free the obstacle The backrest is equipped with a device m that immediately stops the backrest from moving down in the presence of an obstacle and automa tically lifts it up to free the obstacle The arms of the assistant s board are equipped with a safety device n that immediately stops the dental chair from moving down if an obstacle is encountered and automatically moves it up to clear the obstacle 4 2 Emergency devices WARNING Use the devices below when movement of the equipment needs to be blocked Dental chair control buttons a or c Pressing any dental chair button blocks all movements Foot control b When the foot control is actuated all movements of the equipment are blocked Foot board i Foot board activated all movements are blocked 4 3 Adjustable headrest 1 The headrest may be of two types k 1 with manual cushion lock lever with pneumatic cushion lock lever Adjusting headrest height with manual locking 1 The head rest blade is positioned through a magnetic clutch The operator should pull up and or push
4. Connections to external instruments The equipment can be hooked up only to other instruments that bear the CE mark Electromagnetic interferences Use of electrical equipment that does not comply to standard IEC 60601 1 3 a Ed 2007 in the office or nearby may cause electromagnetic or other types of interferences resulting in dental unit malfunctions In these cases shut off power to the dental unit before using this equipment Replacing the chucks Operate the turbine release and contra angle only once the chuck has come to a complete stop On the contrary the locking system will wear down and the chucks can slip off causing injury Use exclusively quality drills with an attachment stem of calibrated diameter 1590 1600 mm in compliance with ISO 1797 1 To check the state of the locking system make certain the chuck is firmly secured to the instrument every day before EN 8 CLUTD A3PLUS OPERATING INSTRUCTION fonthos starting work Locking system defects caused by misuse are easily identified and not covered by the warranty Patients with pace makers and or hearing aids When treating patients with pace makers and or hearing aids take into consideration the effects the instruments may have on pace makers and or hearing aids Carefully read technical scientific information available on this subject Implants If the dental unit is used for implant operations using separate equipment designed for this purpose shut off power to t
5. Internal error contact Customer Service Brief red flashes Blue light blue flashing light Handpiece in image freeze mode A gt 2 sec ODINO LI laninos A3PLUS OPERATING INSTRUCTION Gor MyRay iCapture This program allows the C U2 camera to be set up when it is connected to a PC WORKSTATION For a full description on how the MyRay iCapture program works refer to the instructions in electronic format supplied with the C U2 handpiece Disposable infection control sheaths The camera can be a source of cross contamination between patients For this reason always use it with a disposable infection control sheath code 97901590 and disinfect it on the outside after use everyday The sheath with white paper backing is enclosed in two protective layers CQ a transparent one with blue tab at the front and a paper one at the back Follow the directions below to install a new infection control sheath dI 1 Insertthe camera handpiece tip between the layer with White tab and the rear paper backing The lens surrounded by the LEDS must face down towards the rear paper layer Gently push the handpiece to the end of the sheath 2 Pull the blue tab removing the protective covers 3 The dental camera is now protected and ready for use WARNING Always make certain the handpiece is correctly inserted inside the infection control sheath Always change the disposable infection control sheath before using
6. b allowing for movement within a wide range of action The assistant s board comes with a control console d with buttons used to operate the dental chair and hydrogroup Theassistant s board can be equipped with 2 suction tubes and 2 instruments The assistant s board comes with sliding rollers f that guide and hold up the suction tubes ES NOTE the assistant s board is equipped with a safety device that locks out dental chair movement when the board itself is pushed upwards Cleaning the sliding rollers Push down and take off the sliding rollers f Clean the sliding rollers using a suitable product refer to Paragraph 1 4 OCI t t4 EN 31 ODINO A3PLUS OPERATING INSTRUCTION 6 1 Assistant s touchpad Description of the buttons Water to bowl button Water to cup button Operating lamp on off button Home position recall button Rinsing position recall button Chair seat up button Chair back up button Chair seat down button Chair back down button 000000000 6 2 Syringe on assistant s board For detailed information regarding operation of this instrument see para graph 5 3 6 3 Curing lamp on assistant s board For detailed information regarding operation of this instrument see para graph 5 7 6 4 Intraoral camera system on assistant s board For detailed information regarding operation of this instrument see para graph 5 8
7. lo LO 3 tr 2 E 180 Ls 1840 170 Ca 2190 il ODINO A3PLUS OPERATING INSTRUCTION RD 11 Dental operatory maintenance plan Before starting work Drain condensate See paragraph 9 2 Contra angle handpiece Sterilize or disinfect the outside See documentation enclosed with handpiece Micromotor Disinfect outside See paragraph 5 5 Scaler Sterilize or disinfect outside See paragraph 5 6 After each treatment Syringe Sterilize or disinfect outside See paragraph 5 3 Curing lamp Sterilize fibre optic disinfect outside See paragraph 5 7 Disinfect outside Do not use acids or harsh products See paragraph 3 8 Aspirate about 75 litre of sanitizing solution Surgical suction tubes with each cannula See paragraph 9 4 Sterilize the cannula holder terminals Clean with off shelf detergents formulated for Bowl ceramic materials See paragraph 7 1 Do not use acids or harsh products CATTANI gravity separator Drain separator s container See paragraph 9 6 METASYS surgical separator See documentation supplied with the equipment When needed Turbine Sterilize or disinfect the outside See paragraph 5 4 DURR surgical separator See documentation supplied with the equipment Operatory light See documentation supplied with the equipment Monitor with light pole See documentation supplied with the equipment Clean with a suitable disinfectant carefully following the directions for use provided
8. paragraph 7 2 EN 43 laninos A3PLUS OPERATING INSTRUCTION fonthos 9 Maintenance Preventive maintenance Cefla sc Cefla Dental Group the manufacturer of the dental units in accordance with applicable standards IEC 60601 1 3 a Ed 2007 IEC 62353 and directive MDD 93 42 and subsequent changes for medial devices underlines that the preventive maintenance checks for the dental unit specified in the Technical care manual and Maintenance and warranty handbook are to be carried out by authorised personnel at least once every 12 months WARNING The warranty is void if the equipment is serviced repaired altered or modified in any way by personnel who have not been duly authorized by Cefla sc Cefla Dental Group Safety checks In accordance with standard IEC 62353 the safety checks specified in the Technical care manual and Maintenance and warranty handbook sup plied with the dental unit are to be carried out at the intervals required by current local regulations If no precise indications are given Cefla sc the manufacturer of the dental units recommends checking them at least every 24 months at the time of installation and whenever electrical parts that are live are repaired updated A WARNING The manufacturer shall not be held liable for any personal injury or equipment damage if the precautions given above are not observed 9 1 Instrument maintenance Maintenance instructions for the instruments are enclo
9. the device on a new patient This is a fundamental step in preventing cross contamination Disposal the disposable infection control sheaths are to be treated as special waste materials like surgical gloves Cleaning and disinfecting Clean the handpiece with a suitable product after each use refer to Pa ragraph 1 4 WARNING The intraoral camera is not designed for cold sterilization by being soaked for example in solutions such as glutharaldeide or hydrogen peroxide All products must be used as directed by the manufacturer All material used to clean and disinfect must be thrown away Maintenance and repairs The C U2 camera system does not require any particular maintenance In the event of malfunctions please send back the complete handpiece WARNING There are no parts that can be repaired on site In the event of a malfunction please contact an authorized dealer Returning parts Please send back any defective devices in their original packaging Do not reuse damaged boxes The device must be disinfected before being shipped to prevent cross contamination Handpieces that have not been adequately cleaned and disinfected will not be accepted WARNING The sender shall be held responsible for any equipment damaged incurred during shipment regardless of whether or not the devices are under warranty ODINO A3PLUS OPERATING INSTRUCTION GRID 5 9 ZEN Xi integrated sensor Integrated sensor ZEN Xi is
10. 5 seconds for a total of 15 seconds LED S LED 3 ramp cycle L LONG RESTORATION Ramp cycle with emission of 500 mW cm for 5 seconds ramp from 500 to 1800 mW cm for 5 seconds and 1800 mW cm for 10 seconds for a total of 20 seconds 5 Malfunction signalling LED This red LED comes on only if there is a malfunction 6 START button Pressing the START button starts the cycle selected at that moment the cycle indication LED will come on If itis pressed again at any time during the cycle light beam emission will immediately be interrupted 7 MODE button This button is used to select the cycle to be run It allows changing from the cycle you are in at that moment to the immediately following cycle The first three cycles 1 2 and 3 are at constant power and the LEDs come on individually When LED S is on you access ramp cycle mode and at the same time the LEDs B R and L next to it come on Once the LED of the cycle you intend to use has come on the lamp is ready for use Pressing the START button light beam emission is activated according to the cycle selected ES wore the cycle can be selected and the button is operative only when the curing light is not emitting any light If the button is accidentally pressed while light is being emitted nothing will happen Operation WARNING The instrument is supplied non sterile Before use disinfect the lamp grip The optical fibre and the eye pro tection can be ster
11. a medical device employed to acquire intraoral x rays in an electronic format with a Personal Computer interface device When used together with dental practice management software the x ray pictures can be saved in the patient s folder and viewed on the desktop pc monitor at a later time WARNING Do not use the system for any other purpose different from acquisition of intraoral x rays and do not use it if you are not a professional in the dental and radiology fields Use Use and care instructions for integrated sensor ZEN Xi are enclosed with the apparatus NOTE integrated sensor ZEN Xi does not interact with the dental unit from an electric point of view 6 Assistant s board operation Q Pro02 assistant s board Main features Two articulated arms c secure the board a to the hydrogroup b allowing it to be placed in the most convenient work position The assistant s board a comes with a control console d with buttons used to operate the dental chair and hydrogroup Theassistant s board can be equipped with 2 suction tubes and 2 instruments The assistant s board comes with sliding rollers f that guide and hold up the suction tubes ES NOTE the assistant s board is equipped with a safety device that locks out dental chair movement when the board itself is pushed upwards 2 Pro01 assistant s board Main features A single articulated arm e secures the board a to the hydrogroup
12. and of the Council of 8 June 2011 on the restriction of the us electrical and electronic equipment Rohs 2 t amendments and integrations int grations dispositif m dical de Classe lla 2 la directive 2011 65 UE du Parlement europ en et du Conseil du 8 juin 201 dans les quipements lectriques et lectroniques Rohs 2 1 den grundlegenden Anforderungen Anhang der Richtlinie 93 42 EWG nderungen und Erg nzungen medizinisches Ger t der Klasse Ila 2 der Richtlinie 2011 65 EU des Europ ischen Parlaments und des essenciais posteriores alterac es e aditam nt s dispositivo GR AnA voupe ie Tv aTZOKAEIOTIKN PY Nog Hawy M KNI UMTEJIGHYNO O MIMEH HMAM n A NONHE NAM MeAMLMHCKOe ycTportcrBo Knacca Ila 2 anpextuse 2014 65 EC EBponapnaMeHra n Cosera Esponbi or 8 woun 2011 rona no OrpaHnyeHnio MCNION JOBAHMA ONPeAeNeHHbIX ONACHbIX Beujecra B3nekTpuueckoM n 3niekrpoHHoM o6opyaosaHuM Rohs 2 PL O wiadczamy na swoj wy czn odpowiedzialno ze produkty obj te niniejszym o wiadczeniem sa zgodne 1 z zasadniczymi wymaganiami Za cznik przewidzianymi dyrektyw 93 42 EWG Wyroby Medyczne D z moc ustawy 46 97 wraz z p niejszymi zmianami i uzupe nieniami wyr b medyczny Klasa Ila 2 z dyrektyw 2011 65 WE Parlamentu europejskiego i Rady z dnia 8 czerwca 2011r w sprawie ogranicze we wprowadzaniu do obrotu i stosowaniu w sprz cie elektrycznym i elektronicznym okre lonych
13. be deemed unsatisfactory to support the daily usage requirements have it replaced by a qualified technician original spare part no 97901336 WARNING Do not attempt to replace the battery yourself Limited battery warranty The battery in the foot control is covered by a 6 month warranty from the date of installation Recharging the battery When the batteries in the WIRELESS foot control need to be recharged operate as follows Open the protective cap of the connector on the rear of the foot control and connect the recharging cable Connect the other end of the recharging cable to the dental unit see figure At this point the foot control is in the battery charging phase battery char ging warning LED on even though remaining fully functional NOTE the battery is fully recharged in about 6 hours WARNING Exclusively use the dental unit to charge the battery of the WIRE LESS foot control Natural battery discharge Should the battery not be used for long periods of time it may slowly discharge all the same After long periods of disuse it is advisable to always fully charge the battery before use Maintenance and disposal The wireless foot control does not contain parts that can be repaired di rectly by the user In the event of a malfunction do not attempt to carry out maintenance operations but directly contact the manufacturer or his local distributor at the numbers indicated in the warran
14. box Dental chair Fuse F1 230 V Dental chair power supply line Electrical box Quick connect couplers Elise 230 V Electrical outlet power supply line Electrical box MONITOR power supply Fuse 21 V MULTIMEDIA power line Dental chair card area 48 EN A3PLUS OPERATING INSTRUCTION ONINO ODINO 10 1 A3PLUs CONTINENTAL dimensions e amp i N N iXX 1 S3 x E Me d S K ET c A j ni o Oo LO qe 230 700 390 330 390 800 F2 A F1 4840 2190 166 34 880 T 760 580 930 LF 800 100 o lt a O 950 io 610 190 E 860 330 180 1840 170 2190 150 EN 49 ODINO 10 2 A3PLUS INTERNATIONAL dimensions A3PLUS OPERATING INSTRUCTION ODINO i o 3 t d o e 3 t e S S 2 ao 98 I si e c 3 7 i i N a F11 1840 el al Li 2380 i i o e M S 0
15. counter clockwise rotation NOTE when the rheostat switch is on the micromotor cannot reverse Turning on the fibre optics Place the instrument in its work position Press the button to turn the fibre optics on off Indicator light off operation without fibre optics Indicator light on operation with fibre optics NOTE the fibre optics shut off when the micromotor is not used for 30 seconds rheostat switch off Cleaning and care Refer to the specific instructions furnished with the instrument It is recommended to use Daily Oil CEFLA S C for lubrication WARNING Do not soak the syringe in liquid disinfectants or detergents Products not recommended harsh products and or products containing acetone chlorine and sodium hypochlorites Sterilization Handpieces only steam autoclave at 135 C 2 bar following the instructions for use of the device WARNING Carefully read the operating instructions supplied with the instrument before attempting to sterilize Safety guidelines WARNING Never put the contra angle on the micromotor while it is running The chuck release button must be held down during operation Friction between the button and micromotor rotor overheats the head and may cause burns The patient s internal tissues tongue cheeks lips etc must be protected against contact with the button by using suitable instruments mirror etc The chucks and various in
16. down the headrest until it is in the desired position e with pneumatic locking 2 Press and hold down the locking button u to position the headrest as desired Once you have reached the desired position release the button u to lock the headrest in place u Adjusting the cushion with manual lock 1 rotate the lock knob k anti clockwise position the cushion as desired and then retighten the lock knob with pneumatic lock 2 press the lock button u and keep it pressed as you adjust the cushion as desired Once the cushion is oriented as desired just release the button u to lock in place Proper positioning of the headrest WARNING For correct use of the headrest position the patient s head as shown in the figure Important information WARNING Maximum on headrest load 30 Kg Do not attempt to move cushion while patient is resting against it Do not attempt to modify the position of the cushion without first releasing the lock mechanism The pneumatic locking device is active only when the air circuit is pressurized and the dental unit is on 10 EN ODINO A3PLUS OPERATING INSTRUCTION Gaye 4 4 Movable armrests optional Both arm rests are movable and can be turned downwards so that the patient can more conveniently get on and off the chair WARNING Maximum weight supported by armrest 68 kg 5 Instrument boar
17. for dental treatment The instrument board may hold up to 6 instruments The assistant s board can hold 2 suction tubes and 3 instruments This equipment must be used only by adequately trained personnel doctors and paramedics The device is intended for non continuous operation see the operating times of the individual parts in the dedicated sections The device is classified as pollution degree 2 Overvoltage class Il 1 2 1 Classification MEDICAL DEVICES classification Classification of the dental unit in accordance with the indications given in annex IX of directive 93 42 EEC and subsequent changes Class lla ELECTRICAL MEDICAL EQUIPMENT classification Classification of the dental unit in accordance with standard EN 60601 1 for safety of medical equipment Class Type B Reference standards A3PLus series operatory units are designed and constructed in compliance with IEC 60601 1 3 a Ed 2007 IEC 60601 1 6 3 a Ed 2010 IEC 62366 1 a Ed 2007 IEC 80601 2 60 1 a Ed 2012 IEC 60601 1 2 3 a Ed ISO 6875 3 a Ed 2011 ISO 7494 1 2 a Ed 2011 and EN 1717 type AA and AB standards as far as the water mains safety devices are concerned Classification of RADIO DEVICES AND COMMUNICATION TERMINALS only when the WIRELESS foot control is present Equipment classification according to Directive 99 05 EC Art 12 Class I 4 EN ODINO A3PLUS OPERATING INSTRUCTION lontho 1 2 2 Environment
18. from the studio holidays completely empty out the tank marked with an orange band before leaving ODINO A3PLUS OPERATING INSTRUCTION MID 7 5 Automatic tool flushing cycle FLUSHING Description of the system The FLUSHING automatic cycle allows to carry out an automatic cycle of flushing to renew water present in the water ducts of the instruments on the dentist s and the assistant s instrument board Flushing may be carried out with mains water treated water if the WHE system is present or distilled water if the SHS system is present The cycle time is about 2 minutes WARNING It is advisable to carry out a FLUSHING cycle at the beginning of each working day and between two patients FLUSHING cycle setting Ifthe S H S system is present and you want to execute the flushing cycle with distilled water check that the lever b is on the TANK position NOTE it is advisable to execute the flushing cycle with a full tank a Pressthe button onthe dentist s console to access the FLUSHING mode NOTE Three animated symbols will be shown on the console display to confirm that FLUSHING mode has been activated Check that the spray taps d in the lower part of the dentist s instrument board are open if not no or too little water will come out Position the container e forthe instruments to be disinfected on the bowl Insert the tubings of the instruments to be disinfected in the container WARNING For
19. minimum to maximum value set from the instrument board Release the foot control to stop instrument operation NOTE with the spray active at the end of the operation a blast of air is automatically activated to remove any residual drops of liquid in the spray ducts With instrument in place When the foot control is pressed all automatic dental chair movements are automatically blocked Dental chair movement joystick operation 3 Controlla i seguenti movimenti Chair seat up Chair back up Chair seat down Chair back down To stop movement release the button NOTE all dental chair movements are blocked when an instrument is being used or the BIOSTER system is running Left hand button operation 4 Holding down the button for at least 2 seconds with instrument extracted Chip air control sends a jet of air to the turbine or the micromotor Air delivery is activated by pressing the button the jet of air is interrupted when the button is released Briefly pressing the button with the instrument extracted Activation or deactivation of instrument spray WARNING A short acoustic signal warns of the switch When the LED 8 is on it indicates operation with spray Right hand button operation 5 Holding down the button for at least 2 seconds with instrument extracted DT Water Clean System control sends a jet of running water to instruments D such as the turbine the micromotor a
20. niebezpiecznych substancji Rohs 2 TR Bu beyannamede bahsi ge en r nlerin a a da belirtilenlere uygun oldu unu kendi m nhas r sorumlulu umuz alt nda beyan ederiz 1 Kanun h km nde Kararname 46 97 Medikal Ayg tlar 93 42 CEE direktifinde mevcut Ek 1 ana gereklilikler ve sonraki de i iklikler ve eklemelerde belirtilenler Ila s n f medikal ayg t 2 8 Haziran 2011 tarihli Avrupa Parlamentosu ve Konseyi nin Elektrikli ve elektronik cihazlarda baz tehlikeli maddelerin kullan lmas na ili kin k s tlamalar 2011 65 UE direktifi Rohs 2 Imola li 5 Bussolari Paolo Managing Director CEFLAsc Via Selice Prov le 23 a 40026 Imola BO Italy P Iva at It 00499791200 C F 00293150371 cefla Reg Imprese n 5089 BO R E A n 36186 BO www cefla it ceflaimola cefla it Mod 97010019 Rev 4 25 06 2014
21. of PEROXY Ag follow the manufacturer s instructions printed on the package It is important to keep the package tightly closed and store it in a cool place at a temperature not exceeding 25 C WARNING Never leave PEROXY Ag or oxygenated water in the tank a for longer than one month If you are going to be absent from the surgery for long periods of time holidays completely empty out the tank a before leaving W H E system tank emptying This function permits the W H E system s water circuit to be drained if the dental unit is going to be left off for several days Proceed as directed below Place the container provided under the cup spout and start emptying the water circuit by holding down key Water delivery to cup for at least 5 seconds Wait until the water circuit is empty 5 BEEPS signal when the operation has been completed The operatory unit can now be shut off NOTE When turning back on the WHE system will automatically reset gt 5 sec EN 37 laninos A3PLUS OPERATING INSTRUCTION fonthos 7 4 Disinfection cycle with oxygenated water manual BIOSTER cycle With the S H S system you can execute a manual disinfection cycle of the water ducts of all the instruments on the dentist s instrument board and the syringe on the assistant s board using oxygenated water hydrogen peroxide To disinfect proceed as directed below A Prepare the disinfectant Pour un
22. on the assistant s board A beep sounds to signal the selected operating mode 1 BEEP timed operation 3 BEEPS ON OFF operation ES NOTE timed operation is factory set Changing the water to bowl controller with water delivered to cup The controller that delivers water to the bowl when the water to cup button is pressed can be enabled disabled This modification is made by turning on the operating unit simultaneously holding down the Cup Water Delivery and Bowl Water Delivery buttons on the assistant s board A beep sounds to signal the selected operating mode 1 BEEP controller enabled 3 BEEPS controller disabled ES NOTE the controller is enabled by default Water to bowl controller modification with retrieval of dental chair Rinse position The controller that delivers water to the bowl when the dental chair Rinse position button is pressed can be turned on off This modification is made by turning on the operating unit simultaneously holding down the dental chair Rinsing Position and Bowl Water Delivery buttons on the assistant s board A beep sounds to signal the selected operating mode 1 BEEP controller enabled 3 BEEPS controller disabled ES NOTE the controller is enabled by default Water to bowl controller modification with retrieval of dental chair Automatic return The controller that delivers water to the bowl when the dental chair Auto matic return button is pressed can be
23. sanitized using a product suitable for c of ue At the end of each surgical procedure Suckin about half a liter of solution prepared with the selected disinfectant with each of the suction tubes used Sterilize the cannula holder terminals in a steam autoclave at 135 C 2 bar following the instructions for use of the device At the end of each work day Draw in 1 liter of water with each suction tube alternating water and air keep the suction tube alternately in and out of the water Once rinsed with water draw in approximately half a liter of the solution prepared with the selected disinfectant with each of the suction tubes used WARNING Pay strict attention to all the disinfecting product manufacturer s instructions warnings and cautions ES NOTE after disinfecting it is good practise to draw in air only to 0 dry the entire suction system 5 minutes Once a week Remove the cannula body from its cord attachment and lubricate the O rings o using S1 Protective Lubricant for O Rings CEFLA S C Once a year Replace the suction tubes and ends of the tube holder EN 45 laninos A3PLUS OPERATING INSTRUCTION opr 9 5 CATTANI surgical separator At the end of each surgical procedure Suck in about half a liter of solution prepared with the selected disinfectant with each of the suction tubes used Sterilize the cannula holder terminals
24. the handpiece The nozzle a is screwed onto the grip b 3 function syringes Press the button c to take the grip off the syringe casing 6 function syringes Turn the selector switch counter clockwise LED g off and press the button c to take the grip off the syringe casing Cleaning Use soft disposable paper towel dampened with detergents disinfectants WARNING Do not soak the syringe in liquid disinfectants or detergents Products not recommended harsh products and or products con taining acetone chlorine and sodium hypochlorites Sterilization Syringe grip and spout steam autoclave at 135 C 2 bar following the instructions for use of the device NOTE bag before sterilizing Clive laninos A3PLUS OPERATING INSTRUCTION fonthos 5 4 Turbine Connecting the handpiece and changing the chuck Refer to the specific instructions furnished with the handpiece Use A WARNING Read the instructions for use of the various turbines Operating time work 5 min rest 5 min Place the instrument in its work position Use the foot control pedal to start the instrument see paragraph 5 2 The cock f found near the instrument is used to adjust the amount of water in the spray The cock e adjusts the amount of air spray for all the instruments NOTE the turbine cord can also be used to connect the air micro motors equipped with 4 way conne
25. 290014 9 8 METASYS amalgam separator The maintenance instructions for the METASYS amalgam separator are enclosed with the equipment if the equipment comes with this type of separator The separator s control device is located in the hydrogroup WARNING Always wear gloves to prevent contact with infected material when cleaning the separator WARNING When disposing one time use containers full of amalgam observe current local and national laws 9 9 DURR amalgam separator The maintenance instructions for the DURR amalgam separator are enclo sed with the equipment if the equipment comes with this type of separator The separator s control device is located in the hydrogroup ZAN WARNING Always wear gloves to prevent contact with infected material when cleaning the separator WARNING When disposing one time use containers full of amalgam observe current local and national laws 9 10 Dental chair The dental chair does not need any special maintenance In any case operation should be checked by ANTHOS authorized per sonnel once a year EN 47 LUTTO A3PLUS OPERATING INSTRUCTION TONINO 10 Specifications Dental unit Fuse F2 230 V Dental unit power supply line Electrical box Fuse F4 Secondary protection Hydrogroup Electrical box Fuse F5 Secondary protection Dental unit Electrical box Fuse F6 Secondary protection Operatory light Electrical
26. 5 2 2 Push pedal foot coritrol 4 2 ek ga et 16 5 2 3 Power Pedal foot control rese 18 5 24 Wireless foot control ct nennen 19 5 3 SVANGE cited Le oe te C dite eeu 21 5 4 HE ria 22 5 5 MICFOITIOLOE ii rrr nana ra 23 5 6 TR svecevsezeasevs sincera sveeuess exvsceoeees 24 547 TEED curing light ret ta 25 5 8 C U2 dental AM a na a rennen 28 5 9 ZEN Xi integrated sensor tat 31 6 Assistant s board operation 31 6 1 Assistants touchpad 32 6 2 Syringe on assistant s board ea 32 6 3 Curing lamp on assistant s board 32 6 4 Intraoral camera system on assistant s board 32 6 5 SUGUONTUDES siii 33 6 6 Hydraulic saliva ejector i 34 A3PLUS OPERATING INSTRUCTION Tal Tdi 7 3 7 4 7 5 7 6 8 1 8 2 8 3 8 4 9 1 9 2 9 3 9 4 9 5 9 6 9 7 9 8 9 9 9 10 10 10 1 10 2 11 Hydrogroup operation eere 34 Filip a DOW sana ar Er eee alal 34 S H S system Simplified Hygienization System 36 WHE Water Hygienization Equipment system 37 Disinfection cycle with oxygenated water manual BIOSTER cycle ai 38 Automatic tool flushing cycle FLUSHING 39 Opening closing the side hydrogroup cover
27. 97050578 Rev 003 06 2015 2013 ONINO CONTENTS 1 Safety guidelines si s aaa r sa sd 4 1 1 SYMBOL SINN ooi ooo potete trei ERE 4 1 2 Intended USE sasssa sana 4 1 2 1 GASS Nasa a a e della 4 1 2 2 Environmental conditions eee 5 1 2 2 1 Transport and packaging conditions 5 qu2 9 Wanani ne in 5 1 2 4 Disposing the equipment when no longer used 5 1 9 Safety rules i 5 1 4 Cleaning and disinfecting i 7 2 Description of the equipment ses 8 2 Nameplate eccrine ett aed 8 2 2 Det b n ener 8 2 3 Dental chair rerom rentre nter ete 9 3 Turning on the dental operatory 9 4 Dental chair operation 4 1 Safety device Surio eil 4 2 Emiergericy deVICeS ccce ete a 4 3 Adjustable headrest 44 Movable armrests optional nenne 11 5 Instrument board operation 11 5 1 Doctor s control console rnnt 13 5 7141 Turning on the negatoscope 14 5 12 Setting the dental chair automatic return and ribise POSON ensenis iii Lee Pas 14 519 Programming the chair positions A B C and D 14 5 1 4 Emergency stop button g nf 14 5 2 Foot COMOL upisina oer rrr c eene 15 5 2 1 Multifunction foot CONtrol ii 15
28. DINO A3PLUS OPERATING INSTRUCTION GUI The fibre optic is rather delicate and may crack or break if banged affecting the final amount of light emitted If dropped carefully inspect the fibr optic to verify if it is cracked or broken If cracked a strong light appears in the spot in which the fibre is cracked In all these cases the fibre optic must be replaced The curing light handpiece sold separately can be connected only to dental units with connections for this curing lamp Connection to any other equipment may damage the circuits inside the lamp and seriously injure the user and patient The curing lamp handpiece is not protected against liquid penetration IP20 The curing lamp handpiece is not suitable for use in the presence of flammable anaesthetic gas mixed with air oxygen or nitrous oxide NO Cleaning The curing lamp may be a vehicle for cross contamination between patients The most contaminated parts are the fibre optic and eye protection Before sterilizing them make sure there are no residues of curing products if necessary clean with alcohol or a plastic spatula Exclusively sterilize the optical fibre and the eye protection in an autoclave at a sterilization temperature of at least 134 C WARNING The fibre optic is able to support 500 autoclave cycles after which it tends to become opaque and therefore emit less light The eye protection must also be replaced after 500 cycles Contact the manufactu
29. PS twice at the end 2 of the work cycle Allow light emission to stop by itself However it can be stopped at any time by simply pressing the START button again 1 WARNING The curing light is equipped with a system that signals malfun ctions by illuminating the LEDS in different combinations see next paragraph The curing light is equipped with a cut out Indicators The following indicators are provided on the control console to signal curing light failure LED 5 and LED 1 green constantly on Lamp does not emit any light Contact technical service department LED 5 and LED 2 green constantly on Instrument start up controller failure Contact technical service department LED 5 and LED 3 green constantly on Power supply too low Contact technical service department LED 5 and LED 4 flash continuously Handpiece cut out tripped These LEDS will continue to flash until the light has cooled down enough about 5 minutes for it to be used again If the problems persists contact the technical service department Maximum curable thickness The maximum curing thickness with single cycles is 3 millimeters refer to the instructions of the composite material used as well WARNING This thickness must not be exceeded as the layer may not be completely cured Safety guidelines WARNING The LED is a Class 2 light source in accordance with IEC 62471 DO NOT FIX THE BEAM A The light emitted may cause eye d
30. TA CE EU CE EU CONFORMITY DECLARATION DECLARATION DE CONFORMIT CE EU ERKL RUNG VON CE EU ZUSTIMMUNG DECLARACION DE CONFORMIDAD CE EU DECLARA O DE CONFORMIDADE CE EU AHAQEH IIXTOTHTAZ CE EU HEKNAPAUMA COOTBETCTBMA CE EU DEKLARACJA ZGODNOSCI WE CE EU CE EU UYGUNLUK BELGES Incollare in questo spazio l etichetta del complesso odontoiatrico o di altra apparecchiatura o indicare modello e numero di matricola i s Stick the label of the dental equipment or other device Prodotto tipo Product type 3 into this space or write model and serial number Matr Serial N I Dichiariamo sotto la nostra esclusiva responsabilit che i prodotti ai quali questa dichiarazione si riferisce sono conformi 1 ai requisiti essenziali Allegato presenti nella direttiva 93 42 CEE Dispositivi Medici D Lgs 46 97 e successive modifiche ed integrazioni dispositivo medico di Classe lla 2 alla direttiva 2011 65 UE del Parlamento europeo e del Consiglio dell 8 giugno 2011 sulla restrizione dell uso di determinate sostanze pericolose nelle apparecchiature elettriche ed elettroniche Rohs 2 GB We declare on our sole responsibility that the products referred to herein are in compliance with 1 the essential requirements Annexe of Directive 93 42 EEC Medical devices Leg Decree 46 97 and subsed Class lla medical device 2 Directive 2011 65 EU of the European Parliament
31. again If the problem persists contact the technical service department Less light emitted Make certain the fibre optic is not cracked or damaged in any way replace it if it is Contact the manufacturer to purchase original spare parts Make sure there are no residues of curing products on the end of the fibre optic if necessary wipe off with alcohol or a plastic spatula If the handpiece has to be sent back please disinfect it Ship it back in its original packing In addition please enclose a description of the fault with the shipping note Disposal at end of service life Never throw out the equipment in regular trash Observe current local regulations regarding disposal of the equipment at the end of its service life Due to the possibility of cross contamination disinfect the equipment before disposing LUO A3PLUS OPERATING INSTRUCTION fonthos 5 8 C U2 dental camera The C U2 dental camera system complete with an extremely lightweight ergonomic handpiece is specially designed for simple and well conceived usability in examining the oral cavity Auto exposure and fixed focus features provide easy operation This system is designed to allow the dentist to more efficiently show and explain to patients all oral conditions and reasons for planned treatment The C U2 system allows filming and taking high definition 1280x720 live images of the section in question to be taken through a touch of a fingertip on the touch sensi
32. ainst liquid penetration Degree of protection IPX1 Cleaning Clean the foot control using a suitable product see Paragraph 1 4 NOTE if the foot control slips on the floor dust the slip proof rubber found under the base with a dry cloth 5 2 4 Wireless foot control The multifunction and pressure foot control can also be supplied in wireless version The wireless foot control contains a ZIGBEE transmitter module module certified for Europe Canada and the USA Warnings for use WARNING Avoid keeping the wireless foot control in proximity of other RF sources such as wireless LAN cards other radio devices home RF de vices microwave ovens The recommended distance is at least 2 metres in the case of microwave ovens and 1 metre in all other cases Even though the electromagnetic field irradiated by the foot control is insignificant it is advisable NOT to use it in proximity of life sup port equipment e g pacemakers or heart stimulators and hearing aids Before using any electronic device in health facilities always ascertain that it is compatible with the other equipment present Exclusively use the dental unit to charge the battery of the WIRELESS foot control The internal battery may only be replaced by a qualified technician Warnings for first use It is advisable to fully charge the foot control battery before using it for the first time WIRELESS foot control operation The WIRELESS foot control oper
33. al conditions The equipment is to be installed in rooms that satisfy the following requirements temperature between 10 and 40 C relative humidity between 30 and 7596 atmospheric pressure ranging from 700 to 1060 hPa altitude lt 3000 m air pressure entering equipment ranging from 6 to 8 bar water hardness at the equipment inlet must not be above 25 f French degrees or 14 d German degrees for untreated drinking water For water with a higher hardness degree it is recommended to soften water until it reaches a hardness degree between 15 and 25 f French degrees or between 8 4 and 14 d German degreees water pressure entering equipment ranging from 3 to 5 bar water temperature entering equipment not higher than 25 C 1 2 2 1 Transport and packaging conditions Temperature from 10 to 70 C Relative humidity from 1096 to 9096 Atmospheric pressure from 500 to 1060hPa 1 2 3 Warranty Cefla sc Cefla Dental Group stands behind its products warranting safety reliability and performance The warranty is valid only under the following terms The conditions given on the warranty certificate are observed Performing yearly scheduled maintenance The equipment is used only as instructed in this manual The electrical wiring in the room in which the equipment is installed must conform to I E C 60364 7 710 standards for electrical wiring in medical and dental offices A3x1 5 mm line
34. amage in the event of direct radiation without eye protection Eye protection must always be worn when using the curing lamp and do not direct the light beam in eyes The light emitted may damage soft tissues oral cavity mucous gums skin Be extremely careful to direct the light precisely on the material to be cured People with eye diseases such as those who have had cataracts removed or retina diseases must be adequately protected when the curing lamp is used for example with s uitable protective eyewear The rotary end can turn 180 counter clockwise in relation to the handpiece to change over from wand to gun configuration To go back to wand configuration turn clockwise A click is heard when the two positions are reached Do not turn any more once the click is heard The intermediate positions can be used even if a click is not heard Put the fibre optic back into the correct position after turning the end section Do not pull the power cord Do not expose the handpiece to excessive vibrations Do not drop the handpiece and in particular the fibre optic The lamp may break if accidentally banged Check the condition of the handpiece if it has been banged or dropped before using the curing light Try to turn on the light and check operation first without using it on the patient If cracked broken or if there are any other faults do not use the curing light on the patient and contact the technical service department 26 EN O
35. ates in exactly the same way as the wired version therefore refer to the paragraphs above paying WARNING to the specific model used In addition the WIRELESS foot control has a specific LED 7 that indicates the battery charge and the communication status with the dental unit LED 7 indications The colour of the LED indicates the battery charge while the type of flashing indicates the communication status with the dental unit Battery charge CABLE DISCONNECTED CABLE CONNECTED WIRELESS SYSTEM Battery needs charging lt 25 Battery charge error Battery flat E unit off or foot control laninos A3PLUS OPERATING INSTRUCTION ontho Communication status Slow Connection active in wireless mode Fast Connection active with charging cable inserted Battery characteristics The WIRELESS foot control is equipped with a rechargeable Lithium Polymer battery Li Poly 3 7V 5200 mAh type Guangzhou Markyn Battery Co Model 9051109 NOTE the exact battery model number might vary at the discretion of the manufacturer The battery life is approximately 2 months estimating 8 hours of consecutive daily operation with the battery fully charged and fully efficient The battery efficiency reduces with age It is estimated that the efficiency is reduced to 60 after 500 complete recharging cycles Also in this condition the battery should last about 1 month NOTE when the battery efficiency is so far reduced as to
36. b Closing the cover e Put on the cover making sure the two locks are inserted in the notches in the hydrogroup Lastly bring the bottom of the cover near the hydrogroup frame to engage the lock lever again ODINO A3PLUS OPERATING INSTRUCTION Gaye 8 Accessories 8 1 Operating lamp The operating lamp comes in 2 models Lamp with halogen light source model VENUS E For the instructions for use and maintenance see paragraph 8 1 1 2 Lamp with halogen light source model VENUS PLUS The instructions for use and maintenance of the halogen lamp model VENUS PLUS are available in PDF format and can be downloaded from the download area of the website www anthos com ES NOTE during the automatic movements of the dental chair the lamp automatically turns off to prevent blinding the patient 8 1 1 Operating lamp model VENUS E Technical specifications Operation continuous Power supply voltage 12 V 50 60 Hz Power absorbed 55 W Light spot dimensions 70 mm X 140 mm Lux 24 000 max Colour temperature 4 100 K 5 Maximum temperature on accessible surfaces during normal use lt 85 C Protection against electric risks Class ll type B Light source 12 V 55 W G6 35 halogen lamp Total weight 7 3 kg Safety warnings WARNING The lamp must be installed by authorised staff e The lamp may only be used by authorised and adequately trained staff dentis
37. by Removable instrument cords the manufacturer Spray the product on soft See paragraph 5 disposable paper towels Do not use acids or harsh products Clean with a suitable disinfectant carefully Coated surfaces and dental following the directions for use provided by chair upholstery the manufacturer Do not use acids or harsh products Clean filter in running water BOWI niter The content must be disposed of separately She paragraph yeh E Check the filter and replace it ifthe suction rate Surgical suction filter is reduced code 97461845 See paragraph 9 3 At the end of the work day Aspirate about 75 litre of sanitizing solution with Surgical suction tubes each cannula and then dry See paragraph 9 4 Sterilize the cannula holder terminals Hydraulic saliva ejector Clean the filter of the saliva ejector terminal See paragraph 6 6 CATTANI Clean the separator s container drain valve surgical separator and probes See paragraph 9 5 Weekly Cannula holder terminals Lubricate the O rings See paragraph 9 4 Monthly Turbine return air filter a E replace it if necessary See paragraph 9 7 R Contact the technical service department for NUM eneral nspegion See paragraph 1 4 EN 51 Stabilimento Plant Cefla Dental Group Via Bicocca 14 c 40026 Imola BO Italy cefla Tel 39 0542 653441 Fax 39 0542 653555 dental group www cefladentale it cefladentale cefla it DICHIARAZIONE DI CONFORMI
38. chair return control LED not active Battery charge LED wireless version only NOUASWN Control pedal 2 With instrument removed Starts the instrument Adjusts the rpm of rotary instruments To right operation with spray if foreseen for selected instrument NOTE at the end of work air is automatically blown to eliminate any arops of liquid remaining in the spray ducts To left spray free operation With instruments in place Fully right dental chair automatic return RA Fully left patient rinse position reached PR NOTE if the pedal is pushed fully left again the dental chair moves back to the work position WARNING These dental chair functions are activated by keeping the pedal at the end of the travel for at least 2 seconds Joystick for dental chair movement 3 These buttons move the dental chair as follows Dental chair seat up Dental chair backrest up Dental chair seat down Dental chair backrest down To stop movement release the button NOTE all the buttons used to move the dental chair are inoperative when an instrument is removed and the foot control pedal is actuated FUNCTION WIRELESS SYSTEM ODINO A3PLUS OPERATING INSTRUCTION Left hand button operation 4 Key held down at least 2 seconds with the instrument removed Chip air operation delivers air to the turbine or micromotor Air is delivered by pressing the button Air i
39. ctor and conform to ISO 13294 Dental Air Motor WARNING The instrument is supplied non sterile Adjusting the turbine s operating speed Place the instrument in its work position Use buttons INCREASE or DECREASE to set the maximum speed percentage of the turbine IS wore the data set are automatically saved The foot control pedal adjusts the operating speed from the minimum to the maximum values set see paragraph 5 2 Turning on the fibre optics Place the instrument in its work position Press the button to turn the fibre optics on off Indicator light off operation without fibre optics Indicator light on operation with fibre optics ES wore the fibre optics shut off when the turbine is not used for 30 seconds rheostat switch off Cleaning and care Refer to the specific instructions furnished with the handpiece It is recommended to use Daily Oil CEFLA S C for lubrication Sterilization Steam autoclave at 135 C 2 bar following the instructions for use of the device WARNING Carefully read the operating instructions supplied with the handpiece before attempting to sterilize Safety guidelines WARNING The turbine must never be started without attaching the chuck or false chuck The chuck release button must be held down during operation Friction between the button and micromotor rotor overheats the head and may cause burns The patient s internal tissues tongue cheeks li
40. d operation Layout of instruments The positions the instruments are placed in on the board are determined by the customer at the time of order Starting the instruments The syringe is always on see paragraph 5 3 The curing light is turned on with the key when the instrument is withdrawn see paragraph 5 7 Intraoral camera turn on when the instrument is extracted see paragraph 5 8 If connected to an external PC the integrated ZEN Xi sensor is always operative see paragraph 5 9 Once picked up all the instruments are operated with the foot control see paragraph 5 2 Simultaneous use of the instruments A device sees that the instruments cannot be used simultaneously The first instrument removed is operative while those removed there after are deactivated by this device This device allows the chuck to be replaced in one instrument while another is used on the patient Positioning the instrument board The instrument board can move in all directions To adjust the height of the board and or direct it horizontally simply grasp the handle a NOTE only for pantograph arm with pneumatic brake to adjust the height of the dentist s instrument board you first need to press the brake release button O m 2 Pantograph arm There are two types of pantograph arm 1 with manual locking 2 with pneumatic locking Adjusting the pantograph arm with manual brake Balancing of the pantograp
41. diluted PEROXY Ag or 3 oxygenated water into the tank marked with an orange band NOTE make sure that the tank is completely filled B Putting in the disinfectant Make sure the spray cocks d found towards the bottom of the board are open if they are not either very little or no water at all will flow out Take out the bottle of distilled water a turning it clockwise Replace the bottle of distilled water a with the one containing PE ROXY Ag Remove the syringe and empty the duct with the water button NOTE when emptying is complete no water will come out of the duct Repeat the same procedure for the syringe on the assistant s board with the water key Use the Water clean system with the foot control for the remaining dynamic instruments see paragraph 5 2 Turn the toggle c to position OPEN AIR PRESSURE Remove the instruments and fill the ducts with the hydrogen peroxide solution Use the Water clean system with the foot control for the dynamic instruments and the water button for the syringes E SY wore allow the hydrogen peroxide solution to flow out of the instruments 6 7 seconds Put the instruments back in place NOTE at this point the ducts contain hydrogen peroxide C Disinfectant contact time WARNING PEROXY Ag must be left to dwell in the ducts for at least 10 minutes but not more than 30 minutes D R
42. e system can be shut off if municipal water is to be delivered to the instruments This function is obtained by switching the lever b to position LINE Turn the toggle b to position TANK to go back to working with distilled water Cleaning the tank It is advisable to periodically at least once a month cold disinfect only the tank using Peroxy Agt or 3 oxygenated water 10 volumes not diluted and operating as follows take the tank out of the dental unit and empty it fill the tank with disinfectant liquid up to the rim leave the disinfectant liquid to dwell in the tank for at least 10 minutes completely empty out the tank rinse the tank with distilled water fill the tank with distilled water and if necessary add hydrogen peroxide or oxygenated water as described above put the tank back in place in the dental unit ODINO A3PLUS OPERATING INSTRUCTION GUI 7 3 WHE Water Hygienization Equipment system The WHE system assures safe separation physically of the dental unit water supply system from the public water mains thanks to a water free fall section in compliance with EN 1717 In addition the system continuously injects hydrogen peroxide into the water circuit with a final concentration of 0 0696 600 ppm in the ducts suitable for bacteriostasis To this end it is recommended to use PEROXY Ag CEFLA S C never theless 3 oxygenated water may also be used Description of t
43. e under any circumstances Store the handpiece in a clean dry area Do not bend the connecting cable excessively Be extremely careful not to drop the handpiece and do not expose it to excessive vibrations Never use a damaged handpiece Make sure the camera is in good condition and has no sharp edges before attempting to use it If in doubt do not use the handpiece carefully put it away and contact technical assistance Before starting the equipment check the condition of the lens protection Do not aim the light beam at the operator s or patient s eyes during operation During continuous use example more than 10 consecutive minutes the temperature of the camera s tip usually increases significantly if this is un comfortable put the handpiece in its holder for a few minutes to allow the light Source to cool down When the camera needs to be used for a prolonged time reduce light brightness If left running for extended periods make sure the temperature of the tip is acceptable before attempting to use the camera Briefly touch the clear plastic part with your fingertip being careful not to touch the lens in the middle Do not attempt to bend pull or remove the handpiece Connecting the handpiece a a Attach the handpiece of camera C U2 a to the end of the cord and tighten y the ring nut b WARNING Make sure the cord is firmly screwed onto the handpiece b Use of the camera Place the handpiece in its wor
44. ed in a retrieval system or transmitted in any form or by any means i e electronic mechanical photocopying translation or otherwise without the prior written permission of Cefla sc Cefla Dental Group The information technical specifications and illustrations contained in this publication are not binding Cefla sc Cefla Dental Group reserves the right to make technical improvements and changes without modifying the instructions contained herein The manufacturer has a company policy of continual development Although every effort is made to keep technical documentation up to date at all times some of the instructions specifications and figures given in this manual may slightly differ from the purchased product The manufacturer reserves the right to make changes without prior notice The original version of this manual is written in Italian This equipment is equipped with a device that prevents liquid back up 1 1 Symbol definition List of symbols used in this document to denote certain conditions 1 x 9 e 17 1 Type of protection against direct and indirect contact Class l Type of protection against direct and indirect contact Type B 2 WARNING Failure to observe may result in equipment damage or injury to the e user and or patient 3 Consult the instruction manual 2 10 O 18 SN Means that it is advisable to consult the instruction manual before using that part of the device 4 NOTE CR Identifies informat
45. ed to facilitate the cleaning ope rations to remove it simply pull it out of its seat as it is only secured with magnets The silicone instrument holder u can also be sterilized in an autoclave at 121 rubber cycle Instrument cords Clean the instrument cord using a suitable product see Paragraph 1 4 ONINO 5 1 Doctor s control console The following touchpad controllers are provided in dental units models ASPLUS Pushbutton panel for the models A3PLUS CONTINENTAL Pushbutton panel for the models A3PLUs INTERNATIONAL Description of the buttons o INCREASE button increases the settable values DECREASE button decreases the settable values Operating lamp on off button Fibre optic lighting ON OFF button with relative functioning LED Micromotor rotation direction inversion control button with relative functioning LED Negatoscope on off button on console Auxiliary function button available FLUSHING cycle activation button Water to bowl button Water to cup button Dentist s instrument board brake release button only A3 PLUS INTERNATIONAL models Dental chair position storage button Emergency position recall button Home position recall button 00000000000 NOTE operation of dental chair buttons Button pressed shortly set position automatically reached Button held down positioned reached by hand Indicator lights Display for viewing power or speed
46. h arm is determined at the time of installation Any future adjustments can be made using the knob b found on the pantograph arm Turn clockwise to increase clutching of the pantograph arm Turn counter clockwise to decrease clutching of the pantograph arm laninos A3PLUS OPERATING INSTRUCTION fonthos Instrument return arm stopping device only for CONTINENTAL ver sion dentist s instrument boards If this device is provided the instrument return arm can be locked in the instrument extracted position When the device is used a click is heard about 2 3 of the total arm travel To go back to the original condition simply move the arm to the end of its travel A Tray holder module for CONTINENTAL version dentist s instrument board The tray holder module f is made of stainless steel and can easily be removed from its support WARNING Maximum permitted load on the tray holder module f 2 kg distri buted Tray holder module for INTERNATIONAL version dentist s instrument board WARNING Maximum permitted load on the tray holder module e 2 kg distri buted Cleaning the instrument board handle Clean the dentist s module handle using a suitable product see Paragraph 1 4 Cleaning the dentist s instrument board Clean the dentist s instrument board using a suitable product see para graph 1 4 NOTE for CONTINENTAL version dentist s instrument boards the instrument holder x can be remov
47. he dental chair see Paragraph 3 to avoid unwanted movements resulting from faults and or accidental start up of the controls Do not forget to turn off the office s water supply and master switch on the equipment before leaving the surgery The equipment is not protected against liquid penetration IPX O The device is not suitable for use in the presence of flammable anaesthetic gas mixed with air oxygen or nitrous oxide N O This equipment must be stored properly so that it is kept in top working order at all times The manufacturer shall not be held responsible for misuse carelessness or improper use of the equipment This equipment is to be used exclusively by qualified personnel doctors and paramedics with the proper training The user must be present at all times When the equipment is turned on or ready for start up In particular never leave the equipment unattended in the presence of children the mentally disabled or other unauthorised personnel in general Any companions must keep out of the area in which treatment is performed and in any case under the responsibility of the operator The area in which treatment is performed refers to the space around the dental unit plus 1 5 meters Quality of the water delivered by the dental unit The user is responsible for the quality of the water delivered by the dental unit and must adopt measures to maintain it To ensure that you meet the water quality requirements Cefla sc Cefla Denta
48. he system The W H E system is located in the connection box and is always active The system is also equipped with a tank a located in the hydro unit with a capacity of about 500 cc of oxygenated water The W H E system automatically deactivates upon activation of the distilled water delivery if present Signaling the hydrogen peroxide level is low When the hydrogen peroxide in the tank a is about to run out the operatory emits 4 BEEP repeated whenever the equipment is turned on WARNING Should the disinfectant liquid run out the operating unit will remain operational but will use mains and NOT treated water It is advisable to as soon as possible top up the disinfectant tank Filling the tank containing disinfectant liquid When the disinfectant liquid in the tank runs out operate as follows Remove the tank closing cap b lifting it upwards Pour the disinfectant liquid into the tank a until it is full Refit the cap b WARNING Fill the tank only with pure PEROXY Ag or 3 oxygenated water 10 volumes without diluting Errors If the system detects a malfunction 2 BEEPS are provided The system shuts down and the operatory unit does not deliver water In these cases first of all verify water and air are correctly supplied to the operatory unit Shut off and then turn the operatory unit back on if the shutdown persists call technical support PEROXY Ag storage For proper storage
49. his operation after having cut the power to the device to which the lamp is connected and only after it has cooled down Operate as follows to remove the bulb remove the handles remove the transparent screen remove the protective cover h of the bulb remove the bulb m gently pulling it outward fit the new bulb making sure that the contacts are fully inserted in the Socket and that the bulb is in vertical position with respect to the mirror EST NOTE DO NOT touch the new bulb with your hands but handle it with the special protection If you have inadvertently touched the bulb use a wad of cotton wool soaked in alcohol to remove your fingerprints WARNING The bulb must be the type specified in the technical specifications REF V97710003 For refitting follow the procedure in reverse order from removal Maintenance The VENUS E operating lamp does not require any particular maintenance WARNING No parts can be repaired in the field Should any malfunctioning occur please call Technical Service Troubleshooting The bulb does not come on Check that the power supply is connected Check that the bulb is securely inserted in its socket If none of the above caused the malfunction call Technical Service Brightness has considerably reduced Clean the parabola or the front screen using a soft cloth soaked in a glass cleaner Should brightness not return to the initial values call Technical Serv
50. his operation with the lamp off Remove the handle c after turning the ring nut e anticlockwise Removing the transparent screen WARNING Carry out this operation with the lamp off and only after it has cooled down To remove the transparent screen b operate as follows Remove the handles c Support the optical unit Undo the 2 screws g Remove the transparent screen gently pulling it outward For refitting follow the procedure in reverse order from removal Cleaning and disinfection WARNING Carry out these operations with the lamp off and after letting it cool down For cleaning and disinfection use soft non abrasive disposable paper avoid using recycled paper or sterile gauze Lamp arms and optical unit cover clean the outer parts using STER 1 PLUS CEFLA S C or a similar product Transparent screen clean using a soft cloth for glass soaked in a solution of neutral soap and water WARNING Absolutely do not use products containing alcohol Removable handles the handles are cold sterilizable excluding the American and Canadian markets Itis strictly prohibited to use abrasive substances and detergents based on trichloroethylene benzene turpentine or solvents in general on any part of the lamp Do not spray the product used directly on the optical unit Everything used for cleaning and disinfection must be thrown away after use Replacing the bulb WARNING Carry out t
51. ice Brightness does not change when acting on the relative knob Call Technical Service 42 EN ODINO A3PLUS OPERATING INSTRUCTION 8 2 Monitor on lamp pole The instructions for use and maintenance of the monitor are included with the dental unit 8 3 Negatoscope for panoramas An x ray film viewer for panoramic x rays can be mounted on all INTER NATIONAL version instrument boards The screen dimensions are as follows H 210mm L 300mm Per accendere il negatoscopio sufficiente agire sull apposito interruttore a negatoscope on e Q negatoscope off 8 4 Air water 230V quick connect couplers The 230V air water quick connect couplers are located in the front of the utility service centre WARNING Shut off the equipment before attempting to connect or disconnect the air water outlets Technical specifications Power outlet 230VAC 2A in accordance with IEC EN 60320 2 2 F only on dental units with 230 VAC power supply Air quick connect coupler pressure 6 Bar Water quick connect coupler pressure municipal water 2 5 Bar With S H S system 1 8 Bar with W H E system 3 Bar Water quick connect coupler delivery rate municipal water 1800 ml min with S H S system 950 ml min with W H E system 400 ml min NOTE with the SHS system in order to use the quick coupling with mains water the distilled water tank needs to be disabled see
52. ilized in a steam autoclave at 135 C Put the fibre optic c in its housing until it clicks Attach the curing light handpiece to the end of its power cord and tighten the ring e LE S S S D 1 2 3 E laninos A3PLUS OPERATING INSTRUCTION opr Take the light out of its housing on the assistant s board or instrument board NOTE One animated symbol will be shown on the console display O to confirm that the instrument has been activated Turn the front of the light and or fibre optic to the position most suitable for curing wand gun or intermediate position Use the MODE button to select the desired cycle as previously directed the selected cycle is always indicated by the illuminated LED IS wore the curing light has a permanent memory therefore the last cycle used will always be present the next time it is used Place the fibre optic in the position required for curing NOTE the fibre optic should be placed as close to the material to be cured as possible without touching it Press button START to start the cycle WARNING Operation runs 2 consecutive cycles rests 60 seconds NOTE when a programmed cycle is activated the LEDs 1 2 3 B R L indicate the time that elapses in multiples of 5 seconds and turn off every 5 seconds of operation The curing light comes with a beep that BEEPS when the cycle starts 3 BEEPS every 5 seconds of operation and lastly BEE
53. imed button c located on the cover If present remove the valve s for central systems Turn and raise the container d until it is detached from the drain pump k Detach the bowl d from the cover f pulling up the two side rubber bands e After the cleaning operations refit the vessel d after lubricating the O rings with S1 Protective Lubricant for O Rings CEFLA S C O ring 27 before hand with silicon spray Lastly close the side hydrogroup cover 9 6 CATTANI gravity amalgam separator Draining the separator s container e Move the dental unit completely up so that as much liquid as possible can be drained from the container SN WARNING Gloves must be worn when carrying out this operation to prevent contact with infected material Turn the container m counter clockwise and remove it Referto the instructions provided by CATTANI enclosed with the equipment to drain the container in the disposable container provided for this purpose article code 97290027 WARNING When disposing one time use containers full of amalgam observe current local and national laws Su 46 EN ODINO A3PLUS OPERATING INSTRUCTION 9 7 Cleaning the turbine return air filter Monthly check the oil container filter g present in the turbine s return air line If necessary replace the filter element code 97
54. in a steam autoclave at 135 C 2 bar following the instructions for use of the device At the end of each work day Draw in 1 liter of water with each suction tube alternating water and air keep the suction tube alternately in and out of the water Once rinsed with water draw in approximately half a liter of the solution prepared with the selected disinfectant with each of the suction tubes used IS NOTE after disinfecting it is good practise to draw in air only to dry the entire suction system 5 minutes Every 15 days Clean the separator container and probes with a soft sponge and neutral detergent Clean the drain valve for the separator s container with the device pro vided for this purpose Once a year By technician check the siphons and drains check all the internal tubes and plastic and rubber parts subject to wear Before leaving the surgery empty for a few days Start the aspirator and run it 20 30 minutes without sucking in liquids The aspirator will dry itself completely As a result salt caused by moisture and basic substances will not form salt that may cause fan seizure and motor blockage How to remove the separator s container WARNING Gloves must be worn when carrying out this operation to prevent contact with infected material Move the dental chair fully up 5 Open the side hydrogroup cover see paragraph 7 6 2 Completely empty the separator bowl pressing the t
55. insing the ducts e Turn the toggle c to position CLOSE AIR PRESSURE Take out the bottle of hydrogen peroxide a turning it clockwise Put in the bottle containing distilled water Remove the syringe and empty the water duct ES NOTE when emptying is complete no water will come out of the duct Repeat the same procedure to drain the hydrogen peroxide from the ducts for the various instruments Turn the toggle c to position OPEN AIR PRESSURE Remove the instruments and wait for distilled water to flow out Use the Water clean system see paragraph 5 2 with the foot control for the dynamic instruments and the water button for the syringes ESr NOTE allow water to flow out approximately 6 7 seconds Atthis point the ducts contain distilled water again and the dental unit is ready to be used WARNING After disinfection make sure that you close the tank containing PEROXY Ag it will lose effectiveness if exposed to air It is good practice to perform a disinfection cycle at least once a day preferably at the end of the day PEROXY Ag storage For proper storage of PEROXY Ag follow the manufacturer s instructions printed on the package It is important to keep the package tightly closed and store it in a cool place at a temperature not exceeding 25 C AN WARNING Never leave PEROXY Ag or oxygenated water in the tank marked with an orange band for more than one month In case of long absences
56. ion that is especially important for the user and or 3 11 19 Sa assistant Ne 5 Earth ground Functional earth connection NW 0402BQ0101 6 Alternating current 7 Part sterilized in autoclave 8 ON OFF button 9 Refer to the instruction manual 4 I 12 0051 20 Means that for reasons of safety you need to consult the instruction manual before using the device 10 Open a part of the unit 11 Closed a part of the unit 5 13 21 12 Equipmentin accordance with essential requirements of directive EEC C 93 42 and subsequent changes Class lla equipment 13 Equipment in accordance with essential requirements of directive EEC 93 42 and subsequent changes Class medical equipment for ordinary use 14 Waste disposal symbol in accordance with Directives 2002 95 EC 6 Ne 14 22 A 2002 96 EC and 2003 108 EC valid only in the European Union 15 Warning biological hazard It provides information about possible risks of contamination deriving from contact with fluids storage of infected biological waste 16 Manufacturer 7 S 15 17 Month and year of constructions 18 Apparatus serial number 19 DVGW mark quality assurance kitemark regarding supply of drinking E gt bx gt water 20 Product equipment identification code 8 D 16 21 Do not push 22 Foot crushing hazard 23 Device equivalent to Class 2 light source 1 2 Intended use The A3PLUus series of operatories are medical devices intended
57. k position the light comes on and the camera is in the last LIVE mode used lS wore Two animated symbols will be shown on the console display O O to confirm that the instrument has been activated MIRROR function With the camera setto LIVE mode briefly press the Reverse button present on the console to change from viewing real images to mirror images FREEZE function Handpiece C U2 is equipped with a touch sensitive button g ZS Exp R q Tap this button or actuate the foot control to freeze the image of interest Tap this button again or actuate the foot control to unlock the frozen image No Selecting the single image or multi image operating mode With the camera set to LIVE mode hold down the Reverse button present on the console to change from viewing a single image to multi g images and vice versa ES NOTE an icon 1 found in the top right hand corner signals when this mode has been selected 28 EN Celine A3PLUS OPERATING INSTRUCTION Operation in single image mode The live image appears on the monitor when the camera is set to LIVE and single image mode Press the touch key g on the handpiece or actuate the foot control to freeze the image which is immediately displayed on the monitor canceling the previous image NOTE the last image frozen remains on the monitor even if the camera is put back in place Operation in multi image mode The live image appears on the moni
58. l Group advises you to equip the dental unit with an internal or external disinfection system Once installed the dental unit is exposed to contaminants originating from the water supply For this reason it is recommended to install and put it into operation only when you begin using it daily and to perform the decontamination procedures described in the relative chapters right from the first day of installation If the dental unit is equipped with a device for separation from the open water supply system EN 1717 make sure that it also continuously adds disinfectant as required and check that the relative tank contains an adequate quantity see the relative paragraph NOTE contact your local dealer or Dental association for more detailed information about national laws and requirements Applied Parts The parts of the device that during normal use necessarily come into contact with the patient for the device to be able to perform its functions are Dental chair upholstery armrest polymerising lamp fibre optics terminal part of the syringe single use camera protection scaler bits drill handpieces cannula suction terminals Non applied parts that may come into contact with the patient are dental chair armrest support dental chair lower casing patient side hydro unit casing cup water delivery spout bowl suction tubes handpiece body WARNING Moving the dental chair Make sure that the patient is ready to collaborate ask him her
59. l carries heavy fines defined by local laws WARNING The crossed out wheeled bin placed on the equipment indicates that the waste equipment must be collected separately from other waste 1 3 Safety rules WARNING All equipment is permanently installed Depending on the type of chair the unit comes with refer to the installation DATA given in paragraph Specifications Cefla sc Cefla Dental Group shall not be held liable for any personal injury or equipment damage resulting from failure to heed the precaution given above Floor conditions The floor continuous should meet the load bearing capacity set forth by DIN 1055 sheet 3 The weight of the dental unit including a 190 kg patient is about 350 kg sq m This device may not be modified in any way without the authorisation of the manufacturer If the device is modified appropriate examinations and tests need to be conducted in order to ensure continued safe use Cefla sc Cefla Dental Group shall not be held liable for any personal injury or equipment damage resulting from failure to heed the precaution given above Dental chair The maximum chair capacity is 190Kg This weight must never be exceeded Tray holders The maximum weights that can be held must never be exceeded Instrument tray attached to the instrument board maximum allowable load 2 Kg evenly distributed Instrument tray attached to the instrument board maximum allowable load 1 Kg evenly distributed
60. ment 2 1 Nameplate Dental operatory The nameplate is found on the arm between the dental chair and hydro group Data given on plate Manufacturer s name Name of equipment Voltage Type of current i Frequency AERE MADE IN Lo CE ons e Maximum power absorbed TPN s A3 PLUS CONTINENTAL RA Serial number SN Month and year of construction tu CEFLA SC CEFLA Dental Group V BICOCCA 14 C IMOLA BO ITALY 2 2 Dental units The dental units of the A3PLUS series come in the following models Model A3PLUS CONTINENTAL CONTINENTAL version CONTINENTAL version instrument board instruments will return to their original position through the pulling action of the spring operated arms attached to a double supporting arm one of which is articulated while the other is autobalancing Description of equipment Hydrogroup Adjustable arm Instrument board Doctor s console Tray holder Assistant s board Assistant s control console Utility service center Multifunction foot control Water to cup Bowl Autobalancing arm ANTHOS A1 3 dental chair 2 0 ao N53 50 0000509 Model A3PLUS INTERNATIONAL INTERNATIONAL version instrument board instruments placed vertically in housings attached to a double supporting arm one of which is articulated while the other is autobalancing Description of equipment Hydrogroup Adjustable arm Instrument board Docto
61. n control Spray operation LED Battery charge LED wireless version only NOUDSWN Control pedal 2 Operation Remove the instrument Push the foot pedal to start the instrument a Adjust the rpm power of the instrument with the control pedal to right to increase to left to decrease IS wore the control pedal adjusts the speed power of the instrument from the minimum to the maximum value set from the instrument board To stop the instrument simply release the control pedal a NOTE with the spray active at the end of the operation a blast of air is automatically activated to remove any residual drops of liquid in the spray ducts WARNING Instrument spray is activated and deactivated by pressing the but tons 4 or 5 A beep sounds to signal the operating status has been changed When the LED 6 is on it indicates operation with spray 16 EN WIRELESS SYSTEM ONINO Joystick for dental chair movement 3 These buttons move the dental chair as follows Dental chair seat up Dental chair backrest up Dental chair seat down Dental chair backrest down To stop movement release the button ES wore all the buttons used to move the dental chair are inoperative when an instrument is removed and the foot control pedal is actuated Left hand button operation 4 Operation Holding down the button for at least 2 seconds with the instruments in rest position Acti
62. nd the scaler for rinsing the spray 4 I 1 5 ducts Water delivery is activated by pressing the button 5 when the button is released the jet of water is interrupted and a blast of air is au f tomatically activated to remove any residual drops of liquid in the spray ducts 8 Briefly pressing the button with the instrument extracted Activation or deactivation of instrument spray WARNING A short acoustic signal warns of the switch When the LEDs 8 are on they indicate operation with spray ODINO A3PLUS OPERATING INSTRUCTION GUI Right lever operation 6 NOTE the lever functions only with the instruments in their rest position For safety reasons the selected function starts only after the switch has been briefly actuated and then released Lever pushed down Dental chair automatic return program activated Lever pulled up Dental chair program B start Left lever operation 7 NOTE the lever functions only with the instruments in their rest position For safety reasons the selected function starts only after the switch has been briefly actuated and then released Lever pushed down Rinse position PR program activated NOTE when the switch is actuated the second time the dental chair reaches its work position Lever pulled up Dental chair program A start Protection against liquid penetration The foot control is protected ag
63. ning or servicing the device it is recommended to keep the fibre optics shut off Adjusting the scaler s power output Place the instrument in its work position Use buttons INCREASE or DECREASE to set the scaler s maximum power percentage ES NOTE the data set are automatically saved The foot control pedal operates the instrument at the set maximum power see paragraph 5 2 ENDO function The scaler operates at up to of the maximum power set Place the instrument in its work position Press the INVERSION button on the console Indicator light off regular operation Indicator light on ENDO function NOTE with the foot control lever activated you cannot change operation Cleaning and care Refer to the specific instructions furnished with the instrument WARNING Do not soak the handpiece in liquid disinfectants or detergents Sterilization e Torque wrench scaler bits and scaler handpiece steam autoclave at 135 C 2 bar following the instructions for use of the device WARNING Carefully read the operating instructions supplied with the instrument before attempting to sterilize Safety standards WARNING To avoid hazards or malfunctions when connecting the board do not reverse the positions of the cords for scalers that are different brands The inserts attached to the handpiece must comply to Biocompatibility standard ISO 10993 24 EN ODINO A3PLUS OPERATING INSTRUCTION
64. of the dynamic instruments storage function enabled FLUSHING cycle activation A3PLUS OPERATING INSTRUCTION Cleve oniho X RAY VIEWER Rinsing position recall button Seat up and programmed position A recall button Backrest up and programmed position B recall button Seat down and programmed position C recall button Backrest down and programmed position D recall button COOCOO ODINO 5 1 1 Turning on the negatoscope Press the ON OFF button ES NOTE negatoscope shut off is timed and takes place 2 minutes after it was turned on 5 1 2 Setting the dental chair automatic return and rinse position Bring the dental chair into the desired position with the manual movements buttons Hold button SAVE for at least 2 seconds to activate memory mode Storage mode activation is signalled by a short beep and by the flashing 0 on the console display ES NOTE hold down button SAVE for at least 2 seconds to quit without saving the changes made Press the Automatic Return or Rinsing Position buttons to associate the position with the button e g Rinsing Position NOTE the number for the selected button lights up on the display to confirm the position has been saved 5 AUTOMATIC RETURN 6 RINSE POSITION NOTE the RINSE POSITION button brings the chair back into the rinse position without changing the position of the chair seat When the button i
65. ontho 5 7 T LED curing light Technical specifications Supply voltage 24 36 VDC Max power absorbed 6 VA Light source 1 5W LED Wavelength 430 490 nm Acoustic signals at cycle start every 5 seconds and at cycle end Type of operation intermittent 3 consecutive cycles 60 sec rest Programs 6 preset General description of the light Light handpiece Rotary end section Fibre optic Eye protection Power cord Start button NOTE the curing light can be used in different configurations wand gun or any intermediate position to aid the user sOQLOTA NOTE the curing light is delivered in its original packing which should be kept for future shipment Description of the control pad 1 LED 1 STANDARD cycle Emission of 1000 mW cm for 20 seconds this cycle is set as default at the time of sale 2 LED 2 FAST cycle Emission of 1600 mW cm for 15 seconds 3 LED 3 STRONG cycle Emission of 1800 mW cm for 20 seconds 4 LED S When LED S is on you access ramp cycle mode and at the same time the LEDs B R and L next to it come on LED S LED 1 ramp cycle B BONDING Ramp cycle with emission of 500 mW cm for 5 seconds ramp from 500 to 1000 mW cm for 5 seconds and 1000 mW cm for 5 seconds for a total of 15 seconds LED S LED 2 ramp cycle R RAPID RESTORATION Ramp cycle with emission of 500 mW cm for 5 seconds ramp from 500 to 2200 mW cm for 5 seconds and 2200 mW cm for
66. or approximately 5 seconds before performing these operations Routine maintenance Lubricate the o rings c with S1 Protection for o rings lubricant 7 Hydrogroup operation 7 1 Fill cup and bowl The bowl can be turned 160 on the hydrogroup by hand The water to cup spout can be removed to ease cleaning Control buttons Water to bowl Water to cup OO Bowl flushing automatically stops after 30 seconds Bowl flushing automatically starts in the following cases When the rinse position button is pressed When the water to cup button is pressed Hot water to cup When this function is provided hot water is always delivered to the cup Adjusting the amount of water used to fill the cup Turn on the operating unit holding down the Cup Water Delivery button on the assistant s board ES NOTE an intermittent BEEP signals saving is in progress Press the water to cup key once to start filling the cup Once the desired water level has been reached press the water to cup button again making sure the BEEP stops At this point the new water level in the cup has been saved MW J oq a r E Ll ODINO A3PLUS OPERATING INSTRUCTION lontho Changing bowl operation Water delivery to the bowl can take place in an untimed manner on off operation with the relative button This modification is made by turning on the operating unit holding down the Bowl Water Delivery button
67. pray WARNING A short acoustic signal warns of the switch When the LED 6 is on it indicates operation with spray Wireless version A3PLUS OPERATING INSTRUCTION Cleve WIRELESS SYSTEM FUNCTION O 9 WIRELESS SYSTEM FUNCTION N97 This foot control can also be supplied in wireless version see Paragraph 5 2 4 Protection against liquid penetration The foot control is protected against liquid penetration Degree of protection IPX1 Cleaning Clean the foot control using a suitable product see Paragraph 1 4 NOTE if the foot control slips on the floor dust the slip proof rubber found under the base with a dry cloth Gille A3PLUS OPERATING INSTRUCTION GUI 5 2 3 Power Pedal foot control Description of the parts Handle Foot control Dental chair movements Chip air control or activation deactivation of instrument spray function Water Clean System control or activation deactivation of instrument spray function Program B retrieval or patient rinse position activation Program A retrieval or automatic dental chair return activation Spray operation LED OND CARONA Foot control operation 2 With instrument removed Pushing the pedal a the instrument is started The instrument s rpm or power can be adjusted by varying the pressure exerted on the foot control NOTE the foot control adjusts the speed power of the instrument from the
68. protected by a bi polar cut out that conforms to applicable standards 10 A 250 V distance between contacts at least 3 mm must be used to feed the equipment WARNING The color of the three wires POWER NEUTRAL and EARTH should satisfy the requirements of current standards Installation repairs and in general any other operations requiring the casing to be opened are to be performed exclusively by personnel authorized by ANTHOS 1 2 4 Disposing the equipment when no longer used As set out in Directives 2002 95 EC 2002 96 EC and 2003 108 EC on the restrictions of the use of certain hazardous substances in electrical and electronic equipment along with collection treatment recycling and disposal of waste electrical and electronic equipment the latter must be treated as municipal waste therefore sorted and collected separately When new equipment of equivalent type is purchased the waste equipment should be returned to the distributor on a one to one basis for disposal As far as reuse recycling and other forms of waste recovery mentioned above are concerned the manufacturer is responsible for the actions specified by individual local laws Efficient collection of sorted waste separately to recycle and treat waste electrical and electronic equipment aids in preventing negative environmental impacts while protecting human health In addition it facilitates recycling of the materials used to construct the equipment Illegal waste disposa
69. ps etc must be protected against contact with the button by using suitable instruments mirror etc e The chucks and various instruments attached to the handpieces must comply to the standard ISO 10993 22 EN ODINO A3PLUS OPERATING INSTRUCTION Gaye 5 5 Micromotor Coupling the handpieces and changing the chuck Refer to the specific instructions furnished with the micromotor and various handpieces Use A WARNING Also read the instructions for use of the various motors Operating time work 5 min rest 5 min Place the instrument in its work position Use the foot control pedal to start the instrument see paragraph 5 2 The cock f adjusts the water flow to the spray The cock e adjusts the amount of air spray for all the instruments Adjusting the micromotor s operating speed Place the instrument in its work position Use the INCREASE or DECREASE buttons to set the maximum micromotor rotation speed NOTE the data set are automatically saved fim The foot control pedal adjusts the operating speed from the minimum to the maximum values set see paragraph 5 2 Selecting the direction of rotation Place the instrument in its work position Press the INVERSION button on the console Indicator light off clockwise rotation Indicator light on counter clockwise rotation WARNING When the micromotor is taken out 3 BEEPS sound to signal
70. r if present A by pass toggle b is used to shut off the system if municipal water is to a be delivered to the instruments This system allows a disinfecting cycle to be performed for the instru ments spray ducts using hydrogen peroxide see paragraph 7 4 q o WARNING Perform a disinfecting cycle at the end of each work day Filling the tank When the water level in the tank is low about 500 cc fill it as directed below e Turn the switch c to CLOSE AIR PRESSURE Turn the tank counter clockwise and remove the tank a ES NOTE while this operation is being performed the pressu rised air in the tank is automatically released outside Pour distilled water into the tank until the maximum level is reached WARNING Use only distilled water For a higher guarantee of hygiene you can add 600 parts per million of hydrogen peroxide using 20 ml of Peroxy Ag per litre of distilled water or oxygenated water 20 ml of 3 oxygenated water per litre of distilled water Putthe tank back in place turning it clockwise Turn the toggle c to position OPEN AIR PRESSURE WARNING Assure the tank is firmly secured in place before switching the toggle c to position OPEN AIR PRESSURE In case of long absences from the studio holidays completely empty out the tank a before leaving BY PASS function Th
71. r s console Tray holder optional Assistant s board Assistant s control console Utility service center Multifunction foot control Water to cup Bowl Autobalancing arm Negatoscopio per panoramiche optional ANTHOS A1 3 dental chair N 53 5s0O gt 0a00 ILN A3PLUS OPERATING INSTRUCTION 2 3 Dental chair Description of the chair a Headrest b Back c Safety foot board d Movable arm optional Operating times The operating and rest times are as follows work 25 sec rest 10 min Maximum weight capacity The maximum chair capacity is 190 Kg WARNING Do not exceed this value Warnings for use WARNING FOOT CRUSHING HAZARD Pay attention to the patient and the staff during dental chair descent 3 Turning on the dental operatory Press the master switch f and check the following on the control console POWER led g off equipment off pneumatic system disconnected water system disconnected POWER led g A3P on equipment on pneumatic system connected water system connected 4 Dental chair operation The dental chair can be moved as follows Chair seat up down Back up down with inclination of the chair seat Trendelemburg compensated The dental chair can be operated from the following places Instrument board a see par 5 Multifunction foot control b see par 5 2 Assistant s board c see par 6 Clive
72. rer to purchase original spare parts fibre optic eye protection code 97660404 The handpiece cannot be put in autoclave disinfect it on the outside with suitable products and cover it with disposable plastic wrap Use soft dispo sable paper towels to disinfect the handpiece Do not use harsh products or soak in liquids WARNING The curing light handpiece is NOT suitable for autoclave The curing light handpiece is not protected against penetration of liquids therefore it CANNOT be soaked in solution to be sterilized The outside of the lamp should be disinfected with the fibre optic on Do not use any type of disinfectant on the exposed optical surface of the handpiece when the fibre is removed The surface will become irreparably opaque if it comes into contact with disinfectant Maintenance This equipment does not require any particular type of maintenance Only technicians authorized by the manufacturer can replace and or repair the handpiece and dental unit The handpiece has been purposely constructed in a manner that requires specific tools to open it and therefore it cannot be removed by the user The warranty is automatically void if the handpiece is altered in any way Troubleshooting When the lamp is removed the light does not come on no leds on control console illuminated Make sure the Midwest connection is correctly attached to the power cord Carefully screw the ring try to turn on the lamp and then take it off
73. rfaces and plastic parts Upholstery WARNING The VISCOELASTIC upholstery will stain when splashed with mordant acid Immediately rinse with plenty of water if acid spatters on the upholstery Uncoated metal surfaces If you do not use STER 1 PLUS it is recommended to use products that contain at maximum Ethanole 96 Concentration maximum 30 g per 100 g of disinfectant 1 propanol N propanol propyl alcohol N propyl alcohol Concentration maximum 20 g per 100 g of disinfectant Combination of ethanole and propanole Concentration the combination of the two should be maximum 40 g per 100 g of disinfectant A WARNING Do not use products containing isopropyl alcohol 2 propanol iso propanol Do not use products that contain sodium hypochlorite bleach Do not use cleaners that contain phenol Do not spray the selected products directly on the surfaces All products must be used as directed by the manufacturer Do not mix the STER 1 PLUS disinfectant with other products Cleaning and disinfecting instructions Clean and disinfect with single use non abrasive paper avoid using recycled paper or sterile gauze Do not use sponges or in any case any material that can be reused WARNING Shut off the dental unit prior to clean and disinfecting the external parts All material used to clean and disinfect must be thrown away laninos A3PLUS OPERATING INSTRUCTION Gor 2 Description of the equip
74. ricate the O rings of the cannula holder terminals see Pa ragraph 9 4 using S1 Protective Lubricant for O Rings CEFLA S C Note about biocompatibility Only suction tubes supplied with the dental unit and there after original replacement tubes can be used The suction tubes must comply to the standard ISO 10993 cs Jy d EN 33 Ontos A3PLUS OPERATING INSTRUCTION fonthos 6 6 Hydraulic saliva ejector The hydraulic saliva ejector starts running When the tube is removed from the support Cleaning after each use Aspirate about litre of STER 3 PLUS CEFLA S C diluted in a 6 solution equivalent to 60 ml of product in 1 litre of water Cleaning the saliva ejector filter This operation must be carried out at the end of each work day WARNING Put on gloves before attempting to perform this operation e Aspirate about litre of STER 3 PLUS diluted in a 6 solution equivalent to 60 ml of product in 1 litre of water In order to prevent possible dripping of liquids and secretions from the filter b to be extracted aspirate only air for about 5 seconds Take off the cap a by turning and twisting at the same time Remove the filter b Clean replace the filter code 97290060 Put the filter and cap back in place ES NOTE to prevent liquids and matter from dripping from the filter taken out suck air only f
75. s no longer blown when the button is released e Key held down at least 2 seconds with the instruments in place Rinse position PR program activated NOTE press the key again to bring the chair back to the work 65 position amp 4 O Right hand button operation 5 Key held down at least 2 seconds with the instrument removed Water Clean System operation running water is sent to the instruments such as the turbine micromotor and scaler to flush the spray ducts Water is delivered by pressing the button Water is no longer delivered when the button is released and air is automatically blown to eliminate any drops of liquid remaining in the spray ducts Key held down at least 2 seconds with the instruments in place Dental chair automatic return program activated Wireless version This foot control can also be supplied in wireless version see Paragraph 5 2 4 Protection against liquid penetration The foot control is protected against liquid penetration Degree of protection IPX1 Cleaning Clean the foot control using a suitable product see Paragraph 1 4 I NOTE if the foot control slips on the floor dust the slip proof rubber found under the base with a dry cloth 5 2 2 Push pedal foot control Description of the parts FUNCTION 1 Handle Control pedal Dental chair movements Chip air patient rinsing position control Water Clean System Automatic dental chair retur
76. s pressed again the back goes back to the previous position 5 1 3 Programming the chair positions A B C and D Bring the dental chair into the desired position with the manual movements buttons Hold button SAVE for at least 2 seconds to activate memory mode Storage mode activation is signalled by a short beep and by the flashing 0 on the console display NOTE hold down button SAVE for at least 2 seconds to quit without saving the changes made Push the A B C or D keys to associate the relevant position to the key e g C ES wore The number of the button selected e g 3 will be shown on the console display to confirm that it has been stored 5 1 4 Emergency stop button This button can be used in the event of an emergency to bring the patient into the Trendelemburg position ES NOTE the Trendelemburg position is already set and cannot be changed A3PLUS OPERATING INSTRUCTION gt 2 sec gt 2 sec Celine A3PLUS OPERATING INSTRUCTION 5 2 Foot control Three types of foot controls are available O Multifunction foot control 2 Push pedal foot control 3 Power Pedal foot control IS NOTE the multifunction and pressure foot controls can also be supplied in wireless version 5 2 1 Multifunction foot control Description of the parts Handle Control pedal Dental chair movements Chip air patient rinsing position control Water Clean System Automatic dental
77. sed with each instrument WARNING Maintenance of the instruments should be carried out with the equipment shut off 9 2 Draining condensate Perform this operation every day before starting work Proceed as follows put a container under the cock a found below the hydrogroup loosen the cock s knob after the tank has been emptied fully close the cock a sl SCARICO CONDENSA CONDENSATE DRAINAGE SYSTEM 9 3 Cleaning the surgical suction filter This operation should be done daily at the end of work WARNING Always wear gloves to prevent contact with infected material when cleaning the suction filter Proceed as follows Take out the filter d Clean replace the filter code 97461845 Put the filter back in place being careful to removing any amalgam still present at the filter housing s entrance WARNING Remove any amalgam left at the seat of the filter before performing this operation NOTE to prevent liquids and matter from dripping from the filter taken out perform the operations given above with the suction tube running 744 EN ODINO A3PLUS OPERATING INSTRUCTION GUI 9 4 Surgical suction this purpose WARNING For cleaning of the suction system it is recommended to use STER 3 PLUS CEFLA S C diluted in a 6 solution equivalent to 60 ml of product in 1 litre of water The surgical suction system must be
78. struments attached to the handpieces must comply to the standard ISO 10993 Gille A3PLUS OPERATING INSTRUCTION GEI 5 6 Scaler Connecting the handpiece and inserts Refer to the specific instructions furnished with the handpiece WARNING Before attempting to connect the handpiece make certain the con tacts are perfectly dry Blow air from the syringe if necessary to dry Use WARNING Also read the specific instructions for use of the various handpieces Operating time U PZ6 scalers 5 min operation 5 min rest U PZ7 scalers 5 min operation 5 min rest SATELEC scalers 5 min operation 5 min rest SATELEC LED scalers continuous operation Place the instrument in its work position Use the foot control pedal to start the instrument see paragraph 5 2 The cock f adjusts the cooling water flow Safety guidelines f WARNING Before attempting to connect the handpiece make certain the contacts are perfectly dry Blow air from the syringe if necessary to dry e Make sure the threaded sections of the inserts and handpiece are perfectly clean Do not change the shape of the inserts Check wear and tear of the inserts on a regular basis replacing them in the following cases obvious wear drop in performance out of shape or banged Notes on U PZ7 descalers Class 1 LED apparatus Do not direct the light beam in anyone s eyes when clea
79. the syringe instrument you need to use the special adapter f and the heating system must be off The micromotor tubing must be completely inserted into the motor body NOTE the syringe is always active therefore as soon as it is in serted in the instrument container it will immediately start delivering water Execution of the FLUSHING cycle Start the flushing cycle by pressing the button on the dentist s console a second time NOTE the time remaining to the end of the flushing cycle is shown on the console display At the end of the FLUSHING cycle the value 0 is shown on the display the LEDs of the FIBRE OPTICS and INVERSION buttons start flashing Atthis point put the instruments extracted back into place to return to the working condition Interruption of the FLUSHING cycle Once the flushing cycle has been started it CANNOT be interrupted Error signalling Signalling 2 beeps when you attempt to start the flushing cycle Cause No instrument extracted or instruments not equipped with water ducts extracted Remedy Check the instruments extracted and then start the flushing cycle NOTE if the error message appears again call Technical Service EN 39 ODINO A3PLUS OPERATING INSTRUCTION 7 6 Opening closing the side hydrogroup cover Opening the cover Open the cover on the side of the hydrogroup a after pushing up and releasing the lock lever
80. tive area of the handpiece The live intraoral images are displayed on the monitor or Personal Computer WARNING The camera may be used as a tool to aid in diagnosis however the result must always be compared to visual examination and or other diagnostic indications Evaluations and conclusions based only on the image taken by the camera may be poor as the colors and shapes electronically processed may not perfectly correspond to the actual ones Safety guidelines WARNING The external PC and the external monitor must be of medical grade namely they have to be certified and comply with the standard IEC 60601 1 3rd Ed They have to be able to ensure a double insulation level for both patient 2 MOPP and operator 2 MOOP with respect to the power mains to all the I O ports USB LAN supplied with Safety Extra Low Voltage SELV Even though the electromagnetic field irradiated by the device is insignificant it is advisable not to use it in proximity of life support equipment e g pace makers or heart stimulators according to the specifications included in the user manual of such equipment The disposable infection control sheaths must be used with the device Change the sheath for each new patient After putting on a new disposable infection control sheath check it over before using the camera making sure it is not torn anywhere If it is take it off and put on a new one Do not place the handpiece in liquids or in autoclav
81. to keep his her hands and feet close avoiding incorrect postures Check that the patient is sitting properly when moving the dental chair see figure ODINO A3PLUS OPERATING INSTRUCTION GUI 1 4 Cleaning and disinfecting Cleaning is the first step of any disinfecting process Physically scrubbing with detergents and surface active substances and rinsing with water removes a considerable amount of micro organisms If a surface is not clean first the disinfecting process cannot be successful If a surface cannot be adequately cleaned it should be protected with barriers The outer parts of the equipment must be cleaned and disinfected using a product for hospital use with indications for HIV HBV and tubercolocide medium level disinfectant specifically for small surfaces The various drugs and chemical products used in dentist s surgeries may damage the painted surfaces and the plastic parts Research and tests run show that the surfaces cannot be fully protected against the harsh action of all products available on the market We therefore recommend protecting with barriers whenever possible The harsh actions of chemical products also depend on the amount of time they are left on the surfaces It is therefore important not to leave the product on the surfaces longer than the time specified by the manufacturer It is recommended to use the specific medium level disinfectant STER 1 PLUS CEFLA S C which is compatible with Coated su
82. tor and an icon 1 is shown in the top right hand corner when the camera is set to LIVE and multi image mode When the camera is set to FREEZE hold down at least 2 seconds the left foot control button to select the 4 saved images one after the other When the camera is set to FREEZE hold down the right foot control button to select deselect the full screen view of the selected image NOTE the frozen image appears directly on the monitor in the first box available e g 1 on the page currently displayed Each subsequent frozen image is placed in the next box turning clockwise Once the 4 boxes available are full the next frozen images will replace the existing ones going clockwise NOTE press the MEMORY button for 3 seconds to delete all 4 images on the page displayed VIEW function With the camera set to LIVE mode hold down at least 2 seconds the right foot control button to view the images previously frozen Hold down the left foot control button to select the 4 saved images one after the other Onthe other hand hold down the right foot control button to select deselect the full screen view of the selected image Handpiece status AAn optical guide illuminated by a multicolour LED indicator found in the area near the control button g shows handpiece status as per the table given below Blue light flashes very slowly Handpiece in standby Handpiece activated live images Light blue steady light displayed
83. ts and paramedics Do not apply any weight on any point of the lamp and act on it only with the force necessary to move it An operator must always be present when the lamp is on in particular it should not be left unattended in the presence of children in competent persons or in general persons not authorised for use Do not carry out any maintenance operation on the lamp when the power is on Cut the power before carrying out any operation on the lamp The lamp is not suitable for use in the presence of a mixture of flammable anaesthetic gas with oxygen or nitrous oxide The cleaning operations must be carried out with the lamp off and at room temperature Do not spray detergent liquid directly onto parts of the optical unit The lamp is not protected against penetration of liquids IPXO Do not apply protections not even transparent on the optical unit which may obstruct the cooling air intakes Description a Optical Unit b Transparent screen c Removable handles d On Off and brightness adjustment knob f Self balancing arm Turning the lamp on and off To turn on the lamp turn the knob d clockwise To turn off the lamp turn the knob d fully anticlockwise Brightness adjustment Turn the knob d Clockwise increases the brightness Anticlockwise decreases the brightness EN 41 ODINO A3PLUS OPERATING INSTRUCTION Removing the handles WARNING Carry out t
84. turned on off This modification is made by turning on the operating unit simultaneously holding down the dental chair Automatic Return and Bowl Water Delivery buttons on the assistant s board A beep sounds to signal the selected operating mode 1 BEEP controller enabled 2 BEEPS controller disabled ES NOTE the controller is enabled by default Taking off the bowl filter and rinse spout Pull up the spout I and take it off Pull up the filter q and its cover p to remove them Turn the bowl m counter clockwise to release it and then pull it up to take it out Disinfecting and cleaning WARNING Always wear gloves to prevent contact with infected material when cleaning the bowl and bowl filter The parts are to be cleaned daily at the end of each work day Ceramic spouts and bowl thoroughly wash with a specially formulated cleaner for example MD 550 Orotol DURR Bowl filter clean with running water and commercially available cleaning products WARNING Do not use acids or harsh products EN 35 laninos A3PLUS OPERATING INSTRUCTION fonthos 7 2 S H S system Simplified Hygienization System Description of the system The system is equipped with a tank a suitable for distilled water The tank can hold 1 8 liters The tank feeds The sprays of all the instruments found on the instrument and assistant s board To fill the cup Water quick connect couple
85. ty certificate At the end of its lifetime the battery must be replaced by a specialised technician at a Service Centre o MER 20 EN ODINO A3PLUS OPERATING INSTRUCTION 5 3 Syringe Description of the instrument a Nozzle b Handpiece c Syringe release button d Air button e Water button f Hot cold selector only for 6 function syringes g Hot cold indicator light only for 6 function syringes WARNING The instrument is supplied non sterile It is recommended to use single use protections and nozzles Technical charachteristics Operating time 3F syringe continuous operation 6F syringe 5 sec operation 10 sec rest Power supply 6F syringe CEFLA models 24 Vac 50 60 Hz 2 A 50 W Classification in accordance with standard EN 60601 1 6F syringe CEFLA models CLASS II type B Installation plan consult the Technical Installation Manual see Paragraph 11 Use 3 function syringes Place the instrument in its work position Button e water Button d 7 air Buttons e d spray 6 function syringes Place the instrument in its work position Operation with hot spray air and water Turn the selector switch f clockwise LED g on Operation with cold spray air and water Turn the selector switch f counter clockwise LED g off Button e water Button d air Buttons e d spray Removing
86. vation of the Patient rinsing position program NOTE pressing the button a second time returns the dental chair into working position Holding down the button for at least 2 seconds with instrument extracted Chip air control sends a jet of air to the turbine or the micromotor Air delivery is activated by pressing the button the jet of air is interrupted when the button is released NOTE the control works only when the turbine and micromotor are in working position Briefly pressing the button with the instrument extracted Activation or deactivation of instrument spray WARNING A short acoustic signal warns of the switch When the LED 6 is on it indicates operation with spray Right hand button operation 5 Operation Holding down the button for at least 2 seconds with the instruments in rest position Activation of the Automatic dental chair return program Holding down the button for at least 2 seconds with instrument extracted Water Clean System control sends a jet of running water to instruments such as the turbine the micromotor and the scaler for rinsing the spray ducts Water delivery is activated by pressing the button 4 when the button is released the jet of water is interrupted and a blast of air is automatically activated to remove any residual drops of liquid in the spray ducts Briefly pressing the button with the instrument extracted Activation or deactivation of instrument s

"user manual"

Contents

Download Pdf Manuals

Related Search

Related Contents

&quot;user manual&quot;

Contents

Download Pdf Manuals

Related Search

Related Contents

"user manual"