Media Converter User Manual
Contents
1. 1 2 Characteristics U Supports SNMP management only for management device Selectable optical link loss alarm Selectable four transmitting modes Comply with IEEE 802 34 100BASE FX TX IEEE802 3 10BASE T Standard Comply with IEEE 802 1Q VLAN TAG Spanning Tree standard Supports 10 100M full half duplex auto negotiation Supports auto MDI MDIX crossover Supports transmission distance up to 120km Same card on rack mounted and desktop Supports over sized packets up to 1600Bytes Cr Cr Cc cc Supports hot swappable 1 3 Technical Parameters User M anual 5 13 6 13 z Size 21mm x 125mm x 165mm CH a Package 78mm x 170mm x 226mm 2 Work 30 50 C d Storage 40 70 C 3 220V AC 110V AC T Power Z 48V DC 24V DC MM 2km OR MM 5km Fiber 62 5 125 50 125 100 140um Output optical PEAP gt 15dBm power Receiving lt 28dB sensitivity Distance 0 2km or 0 5km O E Connector SC ST FC Q Wavelength 850nm 1300nm 1310nm 5 5 SM d 9 125 8 3 125 8 7 125 or Z Fiber 10 125um SM 20km Distance 0 20km Output optical Re 15 8dBm power Receiving lt 32dB sensitivity User M anual Connector SC ST FC Wavelength 1310nm SM 25km Distance 0 25km Output optical 13 8dBm power Receiving lt 34dB sensitivity Connector SC ST FC Wavelength 1310nm SM 40km2. Distance 0 40km Output optical ied 11 6dBm power Receiving lt 34dB sensitivity Connector SC ST FC Wavelength 1310nm SM 60km i 0 60km when less than 15km Distance use attenuator Output optical power 5 0dBm User M anual 7 13 Receiving lt 36dB sensitivity Connector SC ST FC Wavelength 1310nm SM 80KM 0 80km when less than 15km Distance use attenuator Output optical 8 13 8 3dBm power Receiving lt 36dB sensitivity Connector SC ST FC Wavelength 1550nm SM 120KM 0 120km when less than Distance 15km use attenuator Output optical j p 3 5dBm power Receiving lt 39dB sensitivity Connector SC ST FC Wavelength 1550nm User M anual Chapter 2 Operation 2 1 Front Panel LFP TPLNK bur PWR TX FXLNK 100M E Fig 1 Front panel of dual fiber converter 9 S LEP PWR TX RX FXLNK 100M Fig 2 Front panel of single fiber converter 2 1 1 LED indicator lamp PWR Green ON Full Duplex OFF Half Duplex ON FX Link connected PANE Oren Flash FX signal transmission ON TX Link connected TPLNK Green Flash TX signal transmission 100M Green ON 100M OFF 10M ON Full Duplex OFF Half Duplex EE SE Flash clash when working in hall duplex LFP Green ON LFP enable OFF LFP disable 2 1 2 Optical Port Y RX Optical
3. M edia Converter User M anual Version V5 1 8 Distance MM Multimode SM Single mode O 0 2km MM O 0 5km MM O 0 20km SM O 0 25km SM O 0 40km SM O 0 60km SM O 0 80km SM O 0 120km SM Optical Port O SC O FC O ST Fiber Dual Fiber Single Fiber Converter type InsidePower OutsidePower Module Wavelength TT 850nm TT 1300nm O 1310nm TT 1550nm M anagement C Yes O No User M anual Contents Chapter 1 Introduction oo eee 4 1 1 Descriptions E 4 L Characterisice cece 5 1 3 Technical Parameters 5 Chapter 2 Operation 7 2 1 Front Panel neeenenene gi 2 1 1 LED indicator lamp 7 21 2 Optical ot cscs orontis 7 2 1 3 Ethernet port NODE HUB 7 ee H Chapter 3 Installation 7 EST te EE H User M anual Chapter 1 Introduction 1 1 Descriptions Media converter transmits IP over fiber applied in many places where need long distance transmission Enlarge the TP network range by MM or SM fiber Low consumption and high resistance to electromagnetic interference of the optical fiber make the transmitting distance spread from 100m to several decades KM or hundred KM improve the communication quality as well And make the server repeaters switch terminal PC connect easily The user manual introduces Media Converter characteristic function use and maintenance Please read the user manual carefully before installation User M anual 4 13
4. nd it is OK User M anual 4 Tum on the power supply of the connected Ethernet devices 5 Installation is completed NOTE Single fiber bi directional Media Converter has two types Type A Transmitting wavelength 1310nm receiving wavelength 1550nm Type B Transmitting wavelength 1550nm receiving wavelength 1310nm Type A and Type B must be used in pair i e if one end is TypeA then the other end must be Type B User M anual 13 13
5. signal output Y TX Optical signal input 2 1 3 Ethernet port NODE HUB Supports auto MDI MDIX crossover the pin definition of RJ 45 Pinl TX Output Pin2 TX Output Pin3 RX Input Pin4 NC Not connect Pin5 NC Not connect Pin6 RX Input Pin7 NC Not connect Pin8 NC Not connect User Manual 10 13 2 2SW1 An 8 bits switch on Media Converter PCB signed SW1 settings as follows ON RJ45 port auto negotiation closed SWI 1 OFF RJ45 port auto negotiation enable default ON Half Duplex SW1 2 OFF Full Duplex default ON Connect to 10M SW1 3 OFF Connect to 100M default ON LFP enable SW1 4 OFF LFP disable default ON Remote control closed default SW1 5 OFF Remote control enable SW1 6 ON Cut through User M anual 11 13 OFF Store and forward default SW1 7 NULL SW1 8 NULL 3 1 1 2 3 12 13 Chapter 3 Installation Installation After you received the devices firstly you should check whether the packing is well otherwise please contact with our company or the local agent in time so as to solve the problem Turn on the power supply of the converter Connect local RX to remote TX via optical fiber when local FPL indicator should be bright And connect local TX to remote RX when both local and remote FRX FPL indicators should be bright If they are single fiber converters connect the optical fiber a
Download Pdf Manuals
Related Search