Home

C manual.qxd - Air & Water

1. To release the telescopic tube 4 from the handle push the handle release button 3 and slide the handle out Attach the head or brush to the bottom of the telescopic tube 4 Insert the bottom of the telescopic tube into the neck of the head or brush 26 until it locks into place or line up the square hole in the telescopic tube with the notches in the front of the neck and snap firmly into place To release a head or brush from the telescopic tube 4 push the release button 9 and pull the head or brush tool off the end of the telescopic tool The release button 9 is in the same position on all of the heads brushes and power heads NOTE To attach a SEBO power head ET H ET C ET 1 or ET 2 to your C3 1 canister please refer to your power head owner s manual page 5 for instructions Attaching incorrectly could cause damage Power Heads optional for the C3 1 32 ET C Power head White Part 9254 AM 33 ET H Power head White Part 9256 AM ET H Power head Red Part 9257 AM 34 ET 1 Power head White Part 9258 AM ET 1 Power head Red Part 9299 AM 35 ET 2 Power head White Part 9259 AM NOTE All illustrations shown in this manual represent the C3 1 model except where part numbers and instructions are different for each model OPERATING INSTRUCTIONS ALL C SERIES VACUUMS Starting The Machine Figures 1 amp 2 Before turning on your canister make sure that you have a firm hold on the handl
2. bag holder see pg 9 figures 12 amp 13 3 Micro hygiene filter not properly 3 Remove the filter bag cover 21 and inserted make sure the micro hygiene filter housing Is seated firmly in place see pg 9 figure 14 C2 1 AIRBELT SCHEMATIC AND PARTS LIST 9648 AM C2 1 Teal 9646 AM C2 1 Red Red Machine Exceptions 12 Part 6383 AM 6309 DR 6006 DR 6127 DR Description Attachment cover C2 1 red On Off pedal incl Pos 8 Cable rewind pedal red Top casing C2 1 red Pos Teal Machine Part 6383 TK 6382 AM 6045 6168 DG 6117 ER 6083 DG 6128 6309 TK 6143 6006 TK 6008 DG 6127 TK 6007 DG 6192 6023 6022 6165 5101 6306 6193 6188 ER 6173 6189 6368 US 6293 6291 6295 ER 6088 6186 6197 DG 6319 UL 6014 6042 6009 DG 6027 ER 6095 DG 6191 AM 6187 6034 6003 DG 6033 AM 6108 AM 6093 DG 6036 DG 6039 6094 6170 ER 6300 HG 6300 DG 6303 HG 6303 DG 6355 AM 6343 DG 1726 HG 6271 DG 6120 3 5091 6213 6086 ER 6046 UL 6047 AM 01 6048 DG 0102 0199 1491 DG 1092 DG 1329 DG 6780 ER 7200 DG Canister with Handle Hose Description Attachment cover C2 1 teal C1 1 teal Spring Bearing block hinge Attachment clip set of 3 Release button Foam seal On Off pedal incl Pos 8 Spring Seal Parking holder rear Top Casing C2 1 teal Plug surround Motor cover Spring Rod Vacuum motor 120 V 1250 W Carbon brush vac m
3. Use of this product by children should always be supervised by an adult Use only as described in this manual Use only manufacturer recommended attachments Do not use with a damaged cord or plug If vacuum is not working as it should has been dropped damaged left outdoors or dropped into water take it to a SEBO service center Do not pull or carry by cord use cord as a handle close a door on cord or pull cord around sharp edges or corners Do not run vacuum over cord Keep cord away from heated surfaces Do not unplug by pulling on cord To unplug grasp the plug not the cord Do not plug in if switch is in the I ON position Do not use outlets above counters to plug In vacuum damage to items in the surrounding area could occur Always carry the vacuum over steps and sills Do not handle plug or vacuum handle with wet hands 12 Do not put any object into vacuum openings Do not use machine with any openings blocked Keep openings free of lint hair and anything that may reduce air flow Do not re use filter bags or wash the filters Do not remove any screws from vacuum Do not vacuum up anything that is burning or smoking such as cigarettes matches or hot ashes Do not use vacuum without filter bag and or filters in place Turn off all machine controls before unplugging Use extra care when cleaning on stairs Do not use machine to vacuum up flammable or combustible liquids such as gasoli
4. all warranty repairs To locate an authorized SEBO dealer in your area or to register a warranty claim in the United States of America please visit our website at www sebo us To locate an authorized SEBO dealer in your area or to register a warranty claim in Canada please call Floor Care Equipment Ltd at 403 250 5005 The warranties provided for above apply exclusively to SEBO Vacuum Cleaners which are used residentially No warranty is provided for SEBO vacuum cleaners used commercially The Wear Parts excluded from warranty coverage include filter bags micro hygiene filters exhaust filters the cable external cord the attachment hose the brush rollers the front bottom plate the rear bottom plate the telescopic tube the crevice nozzle the upholstery nozzle the dusting brush and all of the optional attachments See Optional Attachments on page 5 of this manual This warranty applies only while your SEBO Vacuum Cleaner is physically located within the United States of America and its territories or Canada The purchase receipt showing the date price and item of purchase Is the initial document of proof of purchase and determines the validity of warranty To be certain that your warranty claim can be processed as quickly and efficiently as possible please retain your original purchase receipt and mail in the warranty card provided with your new SEBO vacuum cleaner You may also reg ister on our websit
5. hose contains electrical wires Do not use if damaged cut or punctured Avoid picking up sharp objects Always unplug vacuum before connecting or disconnecting either hose or power head Use a SEBO power head only in combination with a SEBO vacuum Cleaner Do not connect power head to a malfunctioning or damaged vacuum SPECIAL SEBO PRODUCT FEATURES Your SEBO AIRBELIT C canister vacuum is among the most technically advanced vacuum cleaners in the world Some of its unique features are e S Class Filtration Certified by leading Allergy foundations in Europe the AIRBELT C vacuum provides the user with S Class filtration of 99 9 of particles to 0 3 microns This is accomplished by the SEBO three step filtration system First the three layer full size filter bag a collects the vast majority of the debris Then the remainder of the particles are collected by the hospital grade microfilter b Finally the micro exhaust filter c cleans the exhaust air that the vacuum emits The AIRBELT disperses the filtered exhaust air around the canister which provides quiet gentle air flow SEBO s unwavering attention to the complete sealing of the machine ensures no dirt escapes around the microfilters If the microfilters are changed regularly every 10 20 bags the AIRBELT C is perfect for allergy or asthma sufferers e AIRBELT Shock Absorber Your SEBO canister vacuum has a unique soft bumper d which protects your furniture walls and
6. off with the main power switch 15 and then unplug the power cord The bag full or clog light 13 figure 1 works correctly only at full power At lower power levels the bag full or clog light may illuminate incorrectly Check the status of the filter bag regularly at full power If the light remains illuminated at full power and the filter bag is not full check for clogs see page 10 To rewind power cord switch the vacuum off with the main power switch 14 unplug the machine then press the rewind button 16 Hold the plug while rewinding the cord onto the cord reel Avoid letting the plug whip while rewinding A WARNING The quality condition coating texture age and manufactur ing technique of all floor surfaces vary herefore vacuums with rotating brushes includ ing your SEBO may damage some floor coverings or surfaces Some types of high gloss hardwood floors cushion vinyl berber carpets long shag and delicate or hand woven car pets are particularly vulnerable to damage by rotating brushes When possible consult the materials supplied by your flooring manufacturer for information on proper upkeep and cleaning To ensure that your new SEBO vacuum cleaner is compatible with your floor please test the vacuum cleaner on each type of flooring surface in a small inconspicu ous area to determine if any damage occurs If damage occurs stop using the vacuum cleaner immediately 6 Figure 3 ADDITIONAL OP
7. vacuum from damage The AIRBELT disperses the filtered exhaust air around the canister which provides quiet gentle air flow Personalize your canister with a replacement AIRBELT textile cover avail able in a variety of patterns and colors part 6047 AM 01 to 10 See your SEBO Dealer e Bag Full or Clog Warning Light Auto Shut Off If the vacuum s airflow pathway becomes restricted due to a full bag or the existence of a clog the amber BAG FULL OR CLOG light located on top of the canis ter near the hose connection will illuminate If the user ignores this warning the suction motor will heat up due to the lack of cooling provided by the airflow Once the motor reaches a certain temperature it will shut off to protect itself from damage The user should turn the switch off unplug the machine and immediately insert a new bag or remove the clog to remove a clog refer to the Clog Removal section on page 10 After approxi mately 30 minutes the motor will have cooled and the vacuum can be restarted If the airflow is still restrict ed the BAG FULL OR CLOG light will again illuminate and the machine will shut off SEBO three step filtration system Bag full or clog warning light r RN x o luiet air exhaust a IDENTIFICATION OF PARTS 1 Handle grip 11 AIRBELT shock absorber 2 Power control slider C3 1 only 12 Carrying handle 3 Handle release button 13 Warning lights 4 Telescopic tube 14 On Off pe
8. 1 red 7 6005 DR On Off pedal incl Pos 8 9 6006 DR Cable rewind pedal red 11 6397 DR Top casing C3 1 red 29 6197 DG Bottom Casing C3 1 dark gray 41 6093 DG Bag Cover cpl red White Machine Pos SO CONA ORWN gt Canister with Handle Hose Part 6215 AM 6045 6168 DG 6117 ER 6083 DG 6128 6005 GW 6143 6006 GW 6008 DG 6397 GW 6007 DG 6192 6023 6022 6165 05101 6306 6193 6188 ER 6173 6189 6368 US 6293 6291 6407 ER 6088 6186 6197 GW 6318 UL 6014 6042 6009 DG 6027 ER 6095 DG 6191 AM 6187 6034 6003 GW 6033 AM 6108 AM 6093 GW 6036 DG 6039 6094 6170 ER 6348 AM 6349SE 6349 AM 6270 DG 6369 DG 6369 UL 6120 3 6213 6086 ER 6046 UL 6047 AM 01 6048 DG 0102 0199 1491 DG 1092 DG 1329 DG 7200 DG 6421 DG 6420 DG Description Attachment cover white Spring Bearing block hinge Attachment clip set of 3 Release button Foam seal On Off pedal incl Pos 8 Spring Cable rewind pedal Parking holder rear Top casing C3 1 white Plug surround Motor cover Spring Rod Vacuum motor 120 V 1250 W Carbon brush vac motor Seal motor cover Motor cover Rubber mounting 2 pcs Engine mounting Engine mounting Cable rewind unit Air Adapter Internal cable Electronic Controller C3 1 120 V Elbow Seal Bottom casing white Suction neck Seal Spring lock Parking holder side Pin Castor complete Hospital grade microfilter Seal bag cover S
9. ERATING INSTRUCTIONS FOR C 3 1 WITH POWER HEAD Please refer to your power head owner s manual for more information Starting The Machine and Suction Control Figures 4 5 amp 6a A Before turning on your canister make sure that the vacuum handle is in its upright locked position figure 4 1 With the canister main power switch in the OFF position and the power control slider on the handle 2 figure 5 in the OFF position pull the power cord out from the base of the canister The power cord should be unwound from the cable reel at least two thirds of its length The cable rewind is operated by pressing the rewind pedal 16 Before rewinding the cable always switch off and unplug the vacuum 2 Plug the polarized power cord into a 120 volt wall outlet located near the floor 3 Press the main power switch on the base of the canister gently with your foot or hand The green light 13 will illuminate indicating that the power Is on 4 Slide the Power Control Slider 2 figure 5 to the ON position the slider will click when it is pushed out of the OFF position It will then Slide freely between 0 suction and MAX suction Set the slider to the suction desired Release the foot pedal ET 1 ET 2 ET C on power head 36 figure a or for the ET H lower the handle figure 6b Operating The Machine Figures 6a amp 6b B When the power head is on with the handle in the upright locked posi tion see figure 4 abov
10. ND OR NATURE THIS DISCLAIMER OF IMPLIED WARRANTIES SHALL NOT APPLY TO THE EXTENT SAID DISCLAIMER IS NOT ALLOWED BY APPLICABLE STATE PROVINCIAL LAW To contact SEBO in Canada Floor Care Equipment Ltd Telephone 403 250 5005 Fax 403 250 5057 Website www sebocanada ca MADE IN GERMANY Copyright SEBO America LLC All rights reserved
11. O Lu a as lt O an Lu Tp MADE IN GERMANY OWNER S MANUAL For Household Use Only TABLE OF CONTENTS TECHNICAL Details ciccec cect estate coc 55ca seateneae tees bane cseucewsc wees ee swueseeiweeecesbeveueeseacaes 2 important Safety INSUrUCtIONS 4 2 covesenccesces tesa ceesicn cow tece sas cs ceesaespeewnceceeswoswocneee ss 3 Special SEBO Product Features 2 cccacstautsseuendaceseeerateeesseesaneneatoues couse eeneenewedcasens 4 CERT SUION yc ce acai E 4 FIRB SNOCKADSOT DOT cinere e E E O oasniewnce acces 4 Bag Full or Clog Warning Auto Shut Off 5 2 2 czsuet hoc Uivacut duces cuds deuhadeeaususwauanudeedeudssevenadeteaes 4 ld entiNcation OF RAMUS 5 lt ciccteauer a naa a a a aa a eee a a ees 9 PISSOMDY nisuna a a a nave E E EE 5 Optional Attachments scnssededousadecasscseseesa noes cata oostaesetecceacusamaeeesen ESE ERE 5 Standard Attachments euss on sesh anena a a a a a a aa aa aaa 9 Operating NST UCUON Sasserra EE a lors r a aa a TENA 6 SLAIN URS WIA RIN G err nia e a Aa EEE U OCON TO uinea a E E A E Ra 6 Operating the Machine sereo ncaa utah ead uca s Sux lial bat E shudiodoseiaueitesuidavaeniess 6 Additional Operating Instructions for C3 1 with Power Head c ccccccccccccccccccccccccece 7 Starting the Machine ang Suction Control aiccein nn a Sideline N a 7 Operating the Machine sssssssseeesssssssseeessssssssrresesssssseresesssssseeeeessssssseresessssssereesssssssreeeeessseno 7 Using the Telescop
12. am bumper 47 remains on the vacuum To replace the AIRBELT insert the side ribs into the grooves 48 Start at the back insert rib into one groove 48 and while holding it down stretch the AIRBELT cover around the foam into the opposite groove 48 Continue around the vacuum Secure the ends with the clip 46 SEBO AIRBELT covers are available in a variety of colors and patterns See your SEBO dealer for available selection Note Never operate the vacuum with Incorrectly attached filters or without filters bag AIRBELT or filter bag housing cover 21 Do not re use filter bags Do not wash and re use filters 42 Filter Bag Part 9093 AM Exhaust Filter Part 6033 AM 44 43 Micro Hygiene Filter Part 6191 AM 46 AIRBELT cover Part 6047 AM 01 08 Figure 15 CLOG REMOVAL A Always unplug vacuum from outlet before removing any clogs NOTE C3 1 users with ET C ET H ET 1 or ET 2 power heads please refer to your power head user s manual for more detailed instructions for remov ing clogs in your power head If the bag full or clog warning light 10 remains illuminated after the fil ter bag has been changed and the filters are in good condition there is like ly a clog in the system Clogs in the Head or Brush Figure 15 Clogs in the swivel neck 49 of a head or brush can be cleared by first press ing the tool release button 9 and removing the brush or head Check inside the swivel nec
13. dal 0 Slide button 15 Attachment housing door 6 Hose neck 16 Cable rewind button 7 Suction opening 17 Power cable 8 Parking holder side 18 Parking holder rear 9 Tool release button 19 Mains Cable C3 1 only 10 Hose 20 Filter bag cover release flap 21 Filter bag cover 22 Micro exhaust filter housing Standard Attachments 23 Crevice nozzle 24 Upholstery nozzle 25 Dusting brush Brushes Heads Optional Attachments 26 Premium Parquet brush standard for the C2 1 and C3 1 Part 7200 DG 27 Kombi nozzle optional for the C2 1 and C3 1 Part 7260 DG 28 Turbo head standard for the C2 1 Optional for the C3 1 Part 6780 ER 29 Radiator brush Part 1496 HG 30 Straight tube 20 in Part 1084 HG 31 Charcoal Filter for odor control Part 6108 AM ASSEMBLY Push the neck 6 of the hose 10 into the suction opening of the canister 7 The notch in the suction opening will line up with the raised bar on the neck When the notches are lined up correctly the neck will snap firmly into place To release the hose from the suction opening press the release tab on the neck of the hose and pull the neck out Attach the short mains cable 19 C3 1 only on the underside of the handle by connecting one cable plug where the hose connects to the handle and the other where the handle connects to the telescopic tube Connect the handle 1 to the top of the telescopic tube 4 Snap in place
14. e the brush roller will not spin To release the ET C ET 1 or ET 2 power head from the upright locked position press down on the foot pedal 36 figure 6a and lower the han dle into the normal operating position The brush roller will then start Spinning and the green light on the power head will illuminate To release the ET H power head from the upright locked position gently place your foot on the power head for leverage and lower the handle into the operating position figure 6b The brush roller will then start spinning The amber indicator light may flicker for a few seconds when you lower the handle this is normal The handle can be lowered to a horizontal position useful for vacuuming under beds You may adjust the suction control with the power control slider 2 fig ure 5 as you vacuum different surfaces or when using the accessory tools For optimal cleaning and brushing operate the machine at the maximum suction power setting and push the power head slowly over the carpet When the canister s main power switch is in the ON position you may turn the power head off and on with the power control slider 2 figure 5 To turn the power head off using the power control slider pull the slider to 0 suction then continue pulling the slider up until it clicks into the OFF position The green power head light will then shut off the green light on the canister 10 will remain illuminated until the vacuum is powered
15. e at www sebo us This warranty gives you specific legal rights You may also have other legal rights which vary from state province to state province SEBO America will not process nor will it accept responsibility for warranty claims for machines pur chased from dealers located in Canada Floor Care Equipment Ltd will not process nor will it accept responsibility for warranty claims for machines pur chased from dealers located in the United States EXCLUSIVE REMEDY The remedies provided under the terms of this Warranty are the purchaser s exclusive remedies and are in lieu of any other remedies otherwise available THE WARRANTY DOES NOT COVER e Used or secondhand products e Products outside of the warranty period e Items not manufactured by SEBO e Normal maintenance service e Equipment damaged by improper use accident other casualty or negligence e Machines equipped with nonauthorized attachments or modifications e Machines on which the serial number has been altered or removed To contact SEBO in the United States of America SEBO America LLC Telephone 303 792 9181 Fax 303 792 9196 Website www sebo us 14 LIMITATIONS AND EXCLUSIONS SEBO MAKES NO OTHER REPRESENTATIONS OR WARRANTIES EXPRESSED OR IMPLIED AND SPECIFICALLY EXCLUDES THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SEBO WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUEN TIAL DAMAGES OF ANY KI
16. e grip to keep the machine from moving forward figure 1 1 With the canister main power switch 14 in the OFF position pull the power cord out from the base of the canister The power cord 17 should be unwound from the cable reel at least two thirds of its length Note do not over extend the cord The cable rewind is oper ated by pressing the rewind button 16 Before rewinding the cable always switch off and unplug the vacuum 2 Plug the polarized power cord into a 120 volt wall outlet located near the floor 3 Press the main power switch on the base of the canister 14 gently with your foot or hand The green light 13 will illuminate indicating that the power is on C3 1 model only Suction Control Figure 2 C2 1 users the suction control dial is located on the top side of the canister on the power switch 14 When the dial shows all yellow the machine is operating at full suction Rotate the dial toward the black to reduce suction for vacuuming curtains or delicate fab rics Suction Control dial on C3 1 users for Information on suction control the C2 1 canisters refer to page 7 of this manual Operating the Machine Figure 3 Adjust the telescopic tube 4 to the correct height by pushing the slide button 5 and gently pulling the tube out to lengthen or pushing it in to shorten Release the slide but ton 5 to lock the tube to the adjusted height eons When changing heads always switch the vacuum
17. e tele scopic tube to clean Remove fibers and hair from the brush manually 8 Figure 11 VACUUM MAINTENANCE Always unplug vacuum from outlet before dismantling any part of machine Changing the Filter Bag Figures 12 amp 13 To change the filter bag set the canister upright as shown in figure 13 pull the cover release flap outward 20 and lift the cover 21 from the filter bag housing The cover release flap must remain in an outward pulled out position to change filter bags and lock them into place Squeeze the clamps 42 on both sides of the filter bag sealing plate 41 slide the plate from the holder 40 and push the filter bag cap on to seal the bag Slide the sealing plate 41 of a new bag into the holder and push it in firmly until it locks into place Re insert cover 21 into filter bag housing push it forward then lock it in place by pushing down the cover release flap 20 You may find it convenient to store the bag cap inside the filter bag housing below the filter bag Do not re use the filter bags Note the nature of the contents of the filter bag will affect the point at which it needs chang ing Fine dust may require an earlier change even though the bag is not full Fluff or hair allows air to pass through easily so the filter bag may overfill before the amber bag full light illuminates Changing the Exhaust Filter Figures 13 amp 14 The exhaust filter 43 needs to be changed when it bec
18. eal microfilter Microfilter holder Exhaust filter Carbon Anti odor filter optional Bag cover complete Cover release with seal Bearing cover Bag holder cpl incl Pos 45 Safety catch with spring Handle w hose C3 1 cpl Light Gray 6 ft Handle w hose C3 1 amp K3 cpl Dark Gray 6 ft Handle w hose C3 1 amp K3 cpl Dark Gray 7 ft Telescoping tube C3 1 Mains cable dark gray Mains cable light gray Foam seal Foam seal Casing clip set of 3 Foam bumper AIRBELT textile cover AIRBELT clip Screw F 3 9 x 13 Screw M4 x 12 Upholstery nozzle Crevice nozzle Dusting brush Premium Parquet nozzle dark gray Standard with C3 1 Slider button cpl Tube release button complete 13 SEBO VACUUM CLEANER WARRANTY Five Years Non Wear Parts Five Years Motor One Year Labor Your authorized SEBO dealer or SEBO will provide the original product purchaser with replacement of Non Wear Parts which fail due to a material or workman ship defect for a period of five 5 years from the orig inal date of purchase of new product SEBO America will provide a five 5 year warranty on suction motors and brush drive motors Your authorized SEBO dealer or SEBO will repair or will cover labor charges associated with repair a defective SEBO vacuum cleaner at no cost to the original pur chaser within one 1 year of original purchase of new product SEBO America or an authorized SEBO dealer must complete
19. es The brush should be cleaned regularly Remove the parquet brush from the telescopic tube to clean Fibers and hair can be pulled out of the bristles manually or vacuum the bristles with with the telescopic tube The brush strips are removable for cleaning and replacement Figure 9 Kombi nozzle Figure 10 The Kombi nozzle is adjustable for carpet or hard floors To set for carpet slide the up arrow button 37 to the right until it clicks into place The hard floor dusting brush will raise up allowing the head to move over the carpet To set for hard floors slide the down arrow button 38 to the left until it clicks into place The brush will lower to gently sweep your floors The slider in Figure 10 is set in the position for carpet The brush should be cleaned regularly Remove the Kombi nozzle from the telescopic tube to clean Fibers and hair can be pulled out of the bristles manually or vacuum the bristles with with the telescopic tube The brush strip is removable for cleaning and replacement Turbo head Figure 11 The Turbo head has an air driven rotating brush for gentle brushing of carpets The Turbo head can be adjusted for high and low pile carpet To adjust the head for high pile carpet push the slider button 39 to the right For low pile carpet push the slid er button 39 to the left The slider in Figure 11 is set in the high pile position The rotating brush should be cleaned regularly Remove the Turbo head from th
20. g any part of the machine Does not turn on Bag full or clog light on Bag full or clog light on amp machine shuts off Does not pick up Filter bag door won t fully close 1 Telescopic tube not inserted properly 1 See page 5 2 Not plugged into working outlet 2 Use another outlet 3 Cable worn 3 Replace cable 4 C3 1 The power control slider 4 C3 1 Set slider switch to on switch is set to 0 off position position See page 7 1 Bag full 1 Replace filter bag See page 9 2 Clog in hose telescopic tube 2 See Clog Removal on page 10 brush or head or entrance to C3 1 users with clog in power filter bag head attachment refer to clog removal in the ET C ET H ET 1 or ET 2 owner s manual 3 Micro hygiene filter dirty 3 Replace micro hygiene filter See page 9 4 Exhaust filter dirty 4 Replace exhaust filter See page 9 1 Hose handle assembly not 1 Reinsert hose handle assembly correctly inserted making sure that it is lined up properly and is snapped into place See page 0 2 The suction control dial is rotated 2 C1 1 amp C2 1 Rotate suction control to no suction setting dial to yellow setting See page 6 3 Filter bag cover not closed 3 See below 1 Cover release flap not fully closed 1 Reinsert bag Lock the cover release flap 20 down firmly 2 Bag not inserted properly 2 Reinsert bag with cover release flap 20 up until firmly latched in
21. he crevice nozzle upholstery nozzle or dusting brush After use switch off the power unplug the vacuum and remove attachment Re insert the attachment tube into the power head or brush turning the tube if needed until you hear it click Into place NOTE C3 1 users with ET C ET H ET 1 or ET 2 power heads please refer to your power head user s manual for more detailed instructions for connecting your power head To use the hose without the telescopic tube switch off the power and unplug the vacu um Push the handle release button 3 and pull the HANDLE out of the end of the tele scopic tube Do not try to separate the hose from the handle Insert an attachment tool if desired onto the end of the handle After use switch off the power unplug the vacu um remove attachment Re insert the handle into the telescopic tube making sure It Is seated correctly and snap it into place Figure 8 USE AND MAINTENANCE OF BRUSHES AND HEADS Always unplug vacuum from outlet before dismantling any part of machine To remove a brush or power head switch off the power and unplug the vacuum Then press the tool release button 9 and pull the tube out NOTE C3 1 users with ET C ET H ET 1 or ET 2 power heads please refer to your power head user s manual for more detailed instructions for operating and main taining your power head Premium Parquet nozzle Figure 9 The parquet nozzle is specially designed for use on hard surfac
22. hematic and Part NUmbers cc cc cece ccc ccc cc ccc cc cccccccccccccccccccccccce 13 Warranty os cies Seis aiwcissaic cidc 2ctb A a cmc biee a aliases a a 14 How To Contact SEBO 14 TECHNICAL DETAILS Vacuum motor 1250 watts 10 6 amps Water lift at motor 90 inches Airflow at motor 170 CFM Filter bag capacity 9 3 liter Sound level 63 dBA Body weight 16 lbs Motor protection thermal cut out Cord length 22 feet Range 36 feet Technical details may be subject to change 1 10 13 14 19 16 17 18 12 IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE When using an electrical appliance basic precautions must always be followed To reduce the risk of electric shock this vacuum cleaner has a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install the proper outlet Do not change the plug in any way Connect only to the outlet type specified on the serial number plate underneath the machine SAVE THESE INSTRUCTIONS WARNING To reduce the risk of fire electric shock or injury Do not leave vacuum while plugged in Unplug from outlet when not in use and before servicing Do not use outdoors or on wet surfaces Do not use near small children or pets Do not allow to be used as a toy
23. ic Tube Hose amp Attachments cccccccccccccccccccccccccccccccccccccccecs 8 Use and Maintenance of Brushes and Heads ccccccccccccccccccccccccccscccscccscccscccees 8 IOOF aE US sinect Sarena E a iota ct N atau ca Roe anec sta Wascat Nt Sadan tise 8 TAC HAOMMIONINOZ 72 Oasis Scart ethaceksosved ent loses tibia ucatesdeuataseasasameed sons maeoe et nan axmeinde ts uenuacasawsetontmeds 8 TAS 8 ao ey ml 0 pepe ae ree eee ere ne emcee eer are SA a ren mie RE TS E ES Me eee eR 8 Vacu m Maintenant siisicsccccices s cicero mina ciare tea Cass E aio eG hwceem eG eaeane eeseead sees ceuesenuees 9 Changing tekler Bagera canna auntaqes Crna saudetenuan dancin terse cantsaoeduacauesemenniiauaaese ramen samaunns 9 Crea nG ing the Micro Aygiene Filter darnos ohana ico es na ods stecaa ibe daa ndaceu asses sau eemawaceneeues 9 GC RaNGING TEE MNGUSE FUNCT a ah cums aia aueee Sebauscle tice a e aaa 9 RC VG MG CIC AIRBEC rasene a T NEO 9 Clod REMOVAL seeen EEN TEE 10 Clogs mihe Heador BrUS T asrnane ina E E E E aun mentesuenedemsatesaes 10 Clogs mihe Telescopic TUDE sects iracadstenetenec cdtetekaulieecavaels veo E NT T 10 Glogs MINE HOSE srren E T T E AAE O TEA 10 CLOGS MIM ita Mee TO TION aG ana a cate aa siti tiara 10 TROUDLE SNOOLING GUIDE ti c2c i civeideereeees ce decseseatedioonee Gees cub tee a osaseeosesetecesscastus 11 AIRBELT C2 1 Schematic and Part NUMbers ccccccccccccvcccccccccccccccccccccccccccccccccoece 12 AIRBELT C3 1 Sc
24. k channel 49 and clean out pathway Clogs in the Telescopic Tube Figure 15 Remove head from telescopic tube 4 by pushing the tool release button and pulling the tube out Remove the hose from the top of the telescopic tube by pushing the handle release button 3 A stiff wire or stick can be used to push the clog out of the tube Clogs in the Hose Figure 16 To clear blockages in the hose 10 remove the telescopic tube 4 by pushing the tool release button and pulling the tube out Hold the hose upright with one hand blocking the top and switch on the machine If necessary quickly lift your hand on and off the end of the hose If that does not clear the clog you may also clear clogs by reversing the hose After removing the telescopic tube push the release button on the hose neck 6 and remove the hose from the machine Insert the opposite end of the hose 10 into the suction neck 7 Hold the hose upright with one hand blocking the top and switch on the machine If necessary quickly lift your hand on and off the end of the hose Note Do not insert a wire or stick into the hose Doing so may cause dam age to the hose Clogs in Entrance to Filter Bag Figure 17 Remove hose 10 from vacuum cleaner see figure 16 and remove filter bag cover figure 13 page 9 Clean out entrance to bag 50 10 Figure 19 Figure 16 Figure 17 TROUBLE SHOOTING GUIDE A Always unplug vacuum from outlet before dismantlin
25. ne or use in areas where they may be present 20 21 22 23 24 20 26 27 28 29 30 31 32 Oo Machines can cause a fire when operated near flammable vapors or materials Do not operate this vacuum near flammable fluids dust or vapors Maintenance and repairs must be done by qualified personnel Use only original SEBO replacement parts Do not use vacuum as a Step If vacuum is used on plush carpet or carpet with thick padding do not leave machine standing in one place with machine turned on While the vacuum is in use the power cord should be unwound from the cable reel at least two thirds of its length Hold plug when rewinding onto the cord reel Do not allow plug to whip while rewinding Keep hair loose clothing fingers and all parts of body away from vacuum openings and moving parts Do not place fingers or other body parts under vacuum unless it Is unplugged Do not place the power head over rug or carpet edges The vacuum has a manual reset thermal protector The protector is reset by switching off the vacuum The thermal protector needs some time to cool down after switching off Check the vacuum for air blockages or mechanical failures before switching on Store the vacuum in a dry place at room temperature When the vacuum is not in use you should rewind the cord onto the cord reel Any other servicing should be performed by an authorized service representative The
26. off using the main power control knob Always turn the power off on both the canister and the power head when changing heads or unplugging the vacuum Slide the power control slid er on the power head to its OFF position press the main power switch on the base of the canister gently with your foot or hand then unplug the can ister to completely shut down the power when changing heads or storing the vacuum Hold the plug while rewinding the cord onto the cord reel Avoid letting the plug whip while rewinding Figure 4 Figure 9 Switch Position 2 Figure 9 0 Zero Suction MAX Maximum Suction ON position Slide the slider down toward 0 suction till it clicks out of position OFF position Pull the slider up to 0 suc tion then continue pulling the slider up until it clicks into the OFF position Figure 6b 7 Using the Telescopic Tube Hose amp Attachments Figures 7 amp 8 The telescopic tube 4 is useful for vacuuming corners and hard to reach areas You may use the telescopic tube without a brush power head or attachment To remove a brush or power head switch off the power and unplug the vacuum Then press the tool release button 9 and pull the tube out The standard attachments the crevice nozzle 23 upholstery nozzle 24 and dusting brush 25 may be inserted onto the end of the tube It is not necessary to turn off the vacuum while switching the stan dard attachments t
27. omes extremely dirty or clogged with dust or after approximately 10 to 20 filter bags have been used To remove the exhaust filter set the canister upright as shown in figure 13 pull the cover release flap 20 outward and lift the cover 21 from the filter bag housing Then slide the exhaust filter housing 44 out Pull the filter out To replace slide the new filter into the exhaust filter housing Replace the exhaust filter housing 44 re insert cover 21 into filter bag housing push it forward then lock it in place by pushing down the cover release flap 20 Changing the Micro Hygiene Filter Figures 13 amp 14 After 10 to 20 bags have been used change the micro hygiene filter 45 To remove the micro hygiene filter set the canister upright as shown in figure 13 pull the cover release flap 20 outward and lift the cover 21 from the filter bag housing Then slide the filter 45 out To replace slide in the new filter re insert cover 21 into filter bag housing push it forward then lock it in place by pushing down the cover release flap 20 Changing the AIRBELT Figure 15 If damage occurs to the AIRBELT cover it will need to be replaced To remove the AIRBELT 11 pry off the clip 46 by inserting the tip of a slot head screwdriver under the bottom side of the clip Push downward on the screwdriver until the clip pops off Grasp the edge of the AIRBELT cover and pull the AIRBELT cover will peel off The fo
28. otor Seal motor cover Motor cover Rubber mounting 2 pcs Engine mounting Engine mounting Cable rewind unit Air Adapter Internal cable Electronic Controller C2 1 120 V Elbow Seal Bottom casing dark gray Suction neck Seal Spring lock Parking holder side Pin Castor complete Hospital grade microfilter Seal bag cover Seal microfilter Microfilter holder Exhaust filter Carbon anti odor filter optional Bag cover complete Cover release with seal Bearing cover Bag holder cpl incl Pos 45 Safety catch with spring Handle grip cpl light gray Handle grip cpl dark gray Retaining ring light gray Retaining ring dark gray Hose with end couplings 7 ft Hose with end couplings 6 ft Telescoping tube C2 1 light gray Telescoping tube C2 1 dark gray Foam seal Safety catch spring Foam seal Casing clip set of 3 Foam bumper AIRBELT textile cover dark gray AIRBELT clip Screw F 3 9 x 13 Screw M4 x 12 Upholstery nozzle Crevice nozzle Dusting brush Turbo head dark gray Standard with C2 1 Premium Parquet nozzle dark gray Standard with C2 1 C3 1 AIRBELT SCHEMATIC AND PARTS LIST 9630 AM C3 1 White 9652 AM C3 1 Red SYE 55 i a 65 up 34 53 aal 4T i 35 36 et E 32 A 37 TE A 38 r E 40 39 43 4 i 64 y 41 42 34 Red Machine Exceptions 63 Pos Part Description 1 6383 C3 Attachment cover C3

C manual.qxd - Air & Water

Contents

Download Pdf Manuals

Related Search

Related Contents

C manual.qxd - Air &amp; Water

Contents

Download Pdf Manuals

Related Search

Related Contents

C manual.qxd - Air & Water