Product Manual
Contents
1. 2 Wire Palm Microphone STL 20 20PTT The STL 20 20PTT 1 Wire Monitoring Kit is lightweight and performs in situations from routine to demanding The quick disconnect acoustic tube allows for sharing across multiple shifts and users can rely on high clarity two way belt pack communications in areas with moderate background noise to provide privacy and noise isolation Mechanical Specifications e Cable pull from earphone axial 10 Ibs e Cable flex at earphone 2 000 cycles Environmental Specifications e Operating temperature 20 C to 60 C e Storage temperature 40 C to 80 C STL 40 40PTT The STL 40 40PTT Tactical Monitoring headset is a single flexible ear hanger that molds to the user s ear for a comfortable fit A quick disconnect acoustic tube allows multiple ear insert options and the ability to easily change out acoustic tubes The small lightweight boom transmits audio without being obtrusive Flexible Open Ear Inserts e Open frame design allows users to hear ambient noise e Molded from hypoallergenic material e Available in three sizes and can accommodate left or right ear use e Comfortable for long term wear Mechanical Specifications e Cable pull at earphone axial 10 Ibs e Microphone switch assembly pull axial 10 lbs e Microphone switch operating force 1 5 2 0 lbs Environmental Specifications e Operating temperature 30 C to 75 C e Storage temperature 40 C to 85 C STL 602. 60PTT The STL 60 60PTT 2 Wire palm microphone kit consists of two cables one that has an earphone standard size ear tip acoustic tube adapter and acoustic tube and one that has a combined push to talk switch and microphone both of which terminate in the belt pack accessory connector Mechanical Specifications e Cable pull from earphone axial 10 Ibs e Microphone switch assembly pull axial 10 Ibs e Microphone switch operating force 1 5 2 0 Ibs Environmental Specifications e Operating temperature 30 C to 75 C e Storage temperature 40 C to 85 C INSTALLATION 1 Insert the quick disconnect acoustic tube into the acoustic tube adapter and turn 1 4 clockwise 2 Turn the belt pack off 3 Insert the headset plug into the Belt Pack headset jack Turn to secure as shown 4 The headsets kits can be mounted in either right or left ear 5 The headset kit has a clip to secure it to a shirt collar jacket etc 6 Recommended microphone gain level 4 see belt pack User Manual Programmable Squelch OPERATION e Turn the belt pack on and operate it as explained in the belt pack s User Manual e Insert the eartip into the ear e STL XXPTT Headsets the PTT switch must be pressed to activate the microphone MAINTENANCE Periodically clean the ear tip with a mild soap and water solution to extend the life of the accessory To prolong the life of the accessory store the accessory away from high t
3. 00 ee disconnect acoustic tube kit Beige includes tube adaptor with clip and 114 0102 00 pf a disconnect acoustic tube kit Black includes tube adaptor with clip and 114 0103 00 Quick Disconnect Acoustic Tube Assembly Noise Attenuating Plugs Beige Kit includes acoustic tube adaptor wclip foam eartube plug and foam earplug Quick Disconnect Acoustic Tube Assembly Noise Attenuating Plugs Black Kit 114 0104 00 X i includes acoustic tube adaptor w clip foam eartube plug and foam earplug 114 0105 00 S X Quick disconnect adaptor only with clip Beige 114 0106 00 Oox TK Quick disconnect adaptor only with clip Black 114 0109 00 Flexible Open Ear Insert Left 114 0110 00 Flexible Open Ear Insert Right To Order Sonetics Accessories Call 1 800 833 4558 lt x lt Xx x lt Service phone 503 684 7080 Service email service soneticscorp com Copyright 2012 Sonetics Corporation All rights reserved The information in this document is subject to change without notice No part of this document may be reproduced in any form without prior written consent of Sonetics Corporation This document is number 600 0328 00 Rev A SONETICS STEALTH LIGHTWEIGHT HEADSETS Earphone Inline PTT amp Mic R Clothing Clip a Eia Se i lt Myr STL 20 20PTT 1 Wire Monitoring Earbud Swivel Boom STL 40 40PTT Tactical Monitoring i i Inline PTT amp Mic Clothing Clip STL 60 60PTT
4. HEARING PROTECTION WARNING These communications products are designed to produce a specific audio output level at maximum rated power Many countries have regulations defining the amount of noise that an individual can be subjected to during a normal workday The duration of exposure the level of audio output and the level of ambient noise will affect compliance to these regulations Compliance is application dependent and standards vary It is the SOLE RESPONSIBILITY of the end user to determine applicability of and compliance to local hearing protection regulations When purchasing any accessories that use earphone kits it is the SOLE RESPONSIBILITY of the user to determine proper fit Always use caution when inserting any of the products into your ear ACCESSORIES amp REPLACEMENT PARTS Sonetics P N STL 20 STL 40 60 eea O o 114 0089 00 x x x ClearEarTips 12 eee 114 0090 00 a o Noise Ae Plugs 1 114 0092 00 a eS ae l Noise Moar cee 114 0094 00 x xX Earphone Only Black 114 0095 00 Co a a ae Acoustic Tube with Quick Disconnect amp Elbow 114 0096 00 a I x o Quick disconnect acoustic tube and eartip only 5 114 0097 00 DE R E Quick disconnect acoustic tube and eartip only 1 114 0099 00 Replacement Kit w Acoustic Tube Beige with earphone acoustic tube adaptor and clear eartip 114 0100 00 Replacement Earphone Kit w Acoustic Tube Black with earphone acoustic tube adaptor and clear eartip 114 0101
5. emperature conditions To change the surveillance component parts refer to the exploded view and proceed as follows a To change ear tips on an acoustic tube detach the ear tip from the elbow Position the replacement ear tip over the elbow and press firmly on the ear tip to secure b To change to a noise attenuating assembly on an acoustic tube assembly or to change ear tubes on a noise attenuating assembly detach the ear tip or ear tube piece from the elbow Position the tube end of a new ear tube piece from a noise attenuating plug kit over the elbow and press firmly on the ear tube to secure c To replace an acoustic tube assembly simply grab the base of the unit and turn a 1 4 turn to the left and gently pull out the acoustic tube d To change earphones gently pry the acoustic tube adapter away from the earphone by sliding a thin object between the adapter and the earphone Work the thin object around the circumference of the earphone to free adapter Detach the cable connector from the earphone Reconnect the accessory cable connector to the new earphone by snapping firmly in place Snap the acoustic tube adapter onto the earphone AVAILABLE ACCESSORIES FLEXIBLE OPEN EAR a INSERT NOISE ATTENUATING EARTUBE EARPLUG SD ACOUSTIC f TUBE ADAPTER QUICK DISCONNECT ACOUSTIC TUBE
Download Pdf Manuals
Related Search