Le Maitre Ltd.
Contents
1. amp channels address f ON A Device 1 Channel 1 OFF ON A Device 2 Channel 2 OFF y ON A A Device 3 Channel 3 OFF ON A Device 4 Channel 4 OFF v v ON A A Device 5 Channel 5 OFF v Maintenance e Donotallow the snow liquid to become contaminated replace caps on the liquid container and the snow machine tank immediately after filling e When storing the unit rinse the system with pure water and let it pump for at least 1 2 minutes to ensure a longer life span of the motor and the nozzle e We strongly recommend that you regularly clean the residue around snow machines vent holes on both sides of the machine with a soft brush Technical Specifications Model Arctic Snow Machine Power Supply AC100 120 230 240V 50 60Hz Motor 600W Output Volume 140 ml min Tank Capacity 5 Liters Fluid Consumption 650 seconds liter Remote Included SC 2 10 meter Remote extension EXT 6 DMX ON Board Weight 12Kg Dimensions LxWxH 525 276 228mm Warm up Time N A SN Le Maitre Ltd 6 Forval Close Wandle Way Mitcham Surrey CR4 4NE Tel 44 208 646 2222 www lemaitreltd com2. ARCTIC e LU A C H U N E 3 C Rons X Le Maitre Ltd W4 M N P L SF S 7 ARCTIC S Ww le Maine M A c H N LE MAITRE LTD ARCTIC SNOW MACHINE User Manual Introduction Thank you for choosing Le Maitre s Arctic Snow Machine Prior to use we suggest that you read all the instructions provided you can then look forward to it s reliable and satisfactory performance LN nanoen OF ELECTRIC SHOCK e Keep the device dry and away from rain and moisture Never open the housing e Always unplug your Arctic Snow Machine before filling its tank and turn off or unplug when not in use e Use a grounded electrical outlet only prior to use take care to determine that the unit is installed at the rated voltage e Never aim the output nozzle directly at people or animals and locate the machine in a well ventilated area e Never touch the device during the operation A N DANGER OF BURNING e Never add flammable liquids of any kind oil gas perfume to the snow liquid e Always use Le Maitre approved snow fluid to avoid damage to the unit and to ensure the machine works effectively e Always make sure there is sufficient liquid in the machine s liquid tank Contents Arctic Snow machine with power cable Volume remote controller Fluid tank Hanging bracket Screw set and user manual Arctic Snow external View 01 02 03 04 05 06 O7 08 09 10 Housing 11 Indicato
3. adjust the fan output volume When the fan output is increased the snow flakes produced are smaller when the fan output is decreased bigger snow flakes will be produced The snow output volume will not be affected DMX Control e Connect the DMX lead to the DMX IN socket on the rear of the machine e Test the system by activating the machines selected DMX channel When the channel value is increased the snow machine should produce snow at a steadily increasing rate The unit is OFF when a value between 0 5 is selected It will reach 10096 output once the channel is set to 255 DMX protocol DMX value 0 5 OFF 6 255 ON Addressing Each device occupies 1 channel To ensure that the control signals are properly directed to each device they will need to be addressed This will need to be adjusted for each device by changing the DIP switches as set out in the table below The starting address is defined as the first channel from which the device will respond to the controller Make sure that you do not have any overlapping channels in order to control each device correctly and independently from any other fixture on the DMX data link If two three or more devices are addressed similarly they will work similarly Occupation of the DIP switches Setting the DMX starting DIP switch no 1 2 3 4 5 6 7 8 9 address Device number Starting 1 2 4 8 16 32 64 128 256
4. angle at more than 15 degrees e Always monitor tank fluid level during operation as running the snow machine without fluid can permanently damage the unit If you experience low output mechanical noise or no output at all unplug immediately Check the fluid level the external fuse remote connection and power from the wall If all of the above appears to be working correctly plug the unit in again If snow does not come out after holding the remote ON OFF button down check the hose attached to the tank to make sure there are no blockages in the hose Operation e Plug the power cable into a grounded electrical outlet e Press the red power switch to turn on the machine and make sure the red indicator located above the power switch is lit e The units can be controlled by DMX or the volume remote control see below e Connect the remote control s male 4 pin plug to the machines INPUT socket and make sure the red POWER indicator is lit Cable length 10m Volulme Knob Indicator Green Connector 4 PIN XLR 2 Indicator Red Functions On Off and Volume 4 PIN XLR Rocker Swiich Snowing e Press ON OFF button once the IN USE indicator lights up green the machine is ready to operate during this procedure the machine s fan and motors are operating e Use the adjustable OUTPUT VOLUME on the volume remote controller to set an output value between 10 to 100 e Use the AIR VOLUME button located at the rear of the machine to
5. r Escape Nozzle 12 Control Outlet Socket 3 pin XLR for DMX Hanging Bracket 13 Control Inlet Socket 4 pin XLR for remote Handle 14 Control Outlet Socket 4 pin XLR for remote Safety Ring 15 Rocker Switch Volume Washer 16 Rocker Switch Power Tightening Screw 17 Power Inlet Socket Tank 18 Foot Control Inlet Socket 19 Power Cord and Plug 3 pin XLR for DMX DMX DIP Switches g eee S eie Setup e Remove all packing materials including foam and plastic padding and place machine on a flat surface and follow step set up instructions Tank cap Filter Assembling Tank amp Filter Please note that adaptor with nut set must be tightly connected e Assemble the hanging bracket on the machine use the M8 screws to position the hanging bracket with the machine the tightening screws are for adjusting the machine s angle when in the air Tightening Screw Washer Assembling Hanging Bracket Assemble 4 washers on both inner sides of the hanging bracket with M8 screws on outer sides as indicated e Fill with Le Maitre Snow Fluid and replace cap e Firmly attach the 4 pin connector on the remote control cable to the proper input on the rear of the machine Installation Note e Thisunit can be installed at floor level or suspended overhead where it will work at its best When mounting the unit overhead always ensure that the unit is secure connected by the cable wires passing the safety ring Do not
Download Pdf Manuals
Related Search