Manual - AVLAB
Contents
1. Figure 1 1 Ultra ATA 133 Host Adapter Board Layout Note 1 Connector JP2 and JP3 are for hard drive LED 1 2 Static Electricity Precaution One of the routine precautions you must be aware of when working with computer components is the problem of static electricity discharge Note Leave the product in its static resistant bag until you are ready to 2 install it Caution Static Electricity Discharge may permanently damage your system To avoid possible static electricity discharge during the installation please follow the guidelines below Discharge any static electricity build up in your body by touching a large grounded metal surface or the computer case if plugged in for a few seconds During the installation avoid any contact with internal parts Handle cards only by their external edges Chapter 2 Installation This chapter will guide you through the installation of Ultra ATA 133 Host Adapter in your computer 2 1 Hardware Installation General instructions for installing the board are given since the design of computer chassis varies Refer to your computer reference manual for further information if needed Caution Static Electricity Discharge may permanently damage your system To avoid possible static electricity discharge during the installation please follow the guidelines below Discharge any static electricity build up in your body by touching a large grounded metal surface or the com2. Storage Controller listed under Other Devices Select Driver tab then click Update Driver button Insert the driver diskette select Automatic search for a better driver Recommended then click Next Click Finish remove the driver diskette and click Yes to restart Windows to complete driver installation 2 3 4 Installation with existing Windows ME l When the system starts the Add New Hardware Wizard dialog box will appear Select Search for the best driver for your device and then click Next Insert the driver diskette Check Specify a location and type in A and click Next Click Next and then Finish Remove the driver diskette and restart the computer to complete driver installation Verify Proper Installation for Win 98SE ME 1 2i Go to My Computer Control Panel System Device Manager Double click Hard disk Controllers Silicon Image Sil 0680 Ultra 133 Controller is listed Highlight Silicon Image Sil 0680 Ultra 133 Controller and click Properties A message This device is working properly is displayed in the dialog box the driver has been correctly installed If any error message is displayed remove Silicon Image Sil 0680 Ultra 133 Controller listing restart Windows and reinstall the drivers 2 3 5 Installation with new Windows NT 4 0 1 NHN nA A W N Install the board and follow Microsoft procedures to install Windows NT 4 0 accordingly At the Windows Setup screen pres
3. Ultra ATA 133 Host Adapter User s Manual Fe CE Table of Contents Chapter 1 Introducing 1 1 Introducing the Ultra ATA 133 Host Adapter 1 1 1 1 Key Features and Benefits x ouedavescasiaeeisewdinuaeis Manebennes 1 1 1 2 System Requirements cov ecce ciao eecuntyaees need gas teen ovds 1 1 1 3 Board Layouts cscutcteccaescce sats raadnndenuesan AS E T e aus 2 1 2 1 2 Static Electricity Precaution 0 00 aiaee 2 Chapter 2 Installation 2 1 Hardware Installation i 0 0si60 aceseeeenenevecovarverveeeeesssueess 4 2 2 Device Connection ossenssesnensssresseressseresseerrssseesses 6 2 3 Installing the Software Drivers ccc ceeeee eee eee eee 7 2 3 1 Installation with new Windows 98SE 02 ce ceeseeee es 7 2 3 2 Installation with existing Windows 98SE eee 8 2 3 3 Installation with new Windows Me 0ecee esse eee es 8 2 3 4 Installation with existing Windows Me 0ceeeeee 9 Verify Proper Installation for Win 98SE Me 64 9 2 3 5 Installation with new Windows NT 4 0 ee eee 9 2 3 6 Installation with existing Windows NT 4 0 05 10 Verify Proper Installation for NT 4 0 2 0 0 0 cece ee eee aes 10 2 3 7 Installation with new Windows 2000 eeseeeeeeee eee 10 2 3 8 Installation with existing Windows 2000 6068 10 2 3 9 Installation with new Wi
4. as a boot partition do not connect this drive until the driver for the controller has been completely installed in Windows XP Follow the instructions below to install the driver for the controller first shut down your system and connect the hard disk drive The controller is now ready for operation 1 After installing the board boot up Windows XP Windows will attempt to detect the controller When Found New Hardware Wizard appears Insert the driver diskette into the floppy drive select Install the software automatically 11 Recommended and click Next 3 At the next window choose the entry with A si680 inf under heading location 4 When a warning message pops up click Continue Anyway 5 Click Finish to complete installation Verify Proper Installation for Windows 2000 XP 1 Go to My Computer Control Panel System 2 Click Hardware then click Device Manager 3 Double click IDE ATA ATAPI Controllers then double click Silicon Image Sil0680 ATA 133 Controller to display driver properties 4 A message This device is working properly is displayed in the dialog box the driver has been correctly installed 5303 0169 1
5. ll the software drivers 2 3 Installing the Software Drivers 2 3 1 Installation with new Windows 98SE 1 Install the board and follow Microsoft procedures to install Windows 98 SE accordingly 2 Once Windows has been installed right click My Computer and click Properties Select Device Manager tab 3 Double click PCI Mass Storage Controller listed under Other Devices NY DN Nn A Select Driver tab then click Update Driver button Insert the driver diskette and click Next Select Search for the best driver for your device and click Next Check Specify a location uncheck the other boxes type in A then click Next Click Next again then Finish Remove the driver diskette and restart Windows to complete driver installation 2 3 2 Installation with existing Windows 98SE 1 When the system starts the Add New Hardware Wizard dialog box will appear Click Next Select Search for the best driver for your device and click Next Insert the driver diskette Check Specify a location and type in A and click Next Click Next and then Finish respectively Remove the driver diskette and restart the computer to complete driver installation 2 3 3 Installation with new Windows ME l Install the board and follow Microsoft procedures to install Windows ME accordingly Once Windows has been installed right click My Computer then click Properties Select Device Manager tab Double click PCI Mass
6. low on screen instructions to complete installation 2 3 8 Installation with existing Windows 2000 l 2 After installing the board boot up Windows 2000 Windows will attempt to detect the controller When Found New Hardware Wizard appears select Search for a 10 5 suitable driver for my device recommended and click Next Insert the driver diskette into the floppy drive check Floppy disk drive and click Next Click Next again to continue If the Digital Signature Not Found message appears click Yes Note If prompted for Windows 2000 CD ROM insert the CD into your CD ROM drive and click OK Type in D I386 assuming D is your CD ROM drive and click OK and then Finish Click Finish and restart Windows to complete driver installation 2 3 9 Installation with new Windows XP l Install the board and follow Microsoft procedures to install Windows XP accordingly At the Windows Setup screen press F6 to install the driver Insert the driver diskette Press S then press Enter Select Sil 0680 ATA 133 Controller for Windows 2000 XP and press Enter Press Enter to continue and follow on screen instructions to complete Windows XP installation Note When the Software Installation warning pops up click Yes And when the Hardware Installation warning pops up click Yes again 2 3 10 Installation with existing Windows XP Important If the hard disk drive connected to your controller h
7. ndows XP eceeeeeeee eee 11 2 3 10 Installation with existing Windows XP 00 11 Verify Proper Installation for Windows 2000 XP Chapter 1 Introduction 1 1 Introducing the Ultra ATA 133 Host Adapter This adapter is an ultra high speed dual channel Ultra ATA 133 PCI Host Adapter for use in Pentitum class computers It achieves burst data transfer rates up to 133MB sec and supports drive capacities greater than 137 GB It s enhanced BIOS auto detect device types and fine tunes to the best performance for each connected hard drive 1 1 1 Key Features and Benefits Compliant with UltraDMA6 ATA 133 specification Compliant with PCI v2 2 Plug n play Provides two independent Ultra ATA channels built in 256 byte FIFOs per channel for faster data transfer Supports Ultra DMA 0 6 and Multi word DMA 0 2 Breaks the 137GB barrier Supports hard drives larger than 137GB Co exists with on board IDE controller CRC Cyclical Redundancy Check error checking provides data verification and achieves flawless data transfer Flash BIOS for easy upgrade Full ACPI power management support Works with various brands of Ultra ATA 133 100 66 33 hard disk drivers and ATAPI devices including CD ROM CD R RW DVD ROM and zip drives 1 1 2 System Requirements e Pentium class computer with one available PCI slot e Windows 98SE ME 2000 XP and NT 4 0 1 1 3 Board Layout Secondary IDE Primary IDE HEA l l
8. puter case if plugged in for a few seconds During the installation avoid any contact with internal parts Handle cards only by their external edges 1 Turn OFF the power to your computer and any other connected peripheral devices Unplug the power cord from the back of the computer 2 Remove your computer s cover 3 Select an available PCI slot remove the slot bracket by unscrewing the holding screw and sliding it out Save this screw for securing the Ultra ATA 133 Host Adapter after it is installed AX Figure 2 1 Remove the Slot Bracket To install Ultra ATA 133 Host Adapter carefully align the board s bus connector to the PCI slot on the motherboard Push the board down firmly but gently until it is well seated Note Hold the card by its external edges only Try to avoid touching the components connectors or pins Figure 2 2 Installing the board 5 Secure the board to the rear slot panel Continue to the next section for device connection 2 2 Devices Connection This Ultra ATA 133 Host Adapter is a dual channel Ultra ATA 133 controller that supports up to four IDE hard disk drives or ATAPI devices If you plan to use the second IDE channel SECONDARY IDE you will need to purchase another 40 pin 80 wire Ultra ATA ribbon cable Note Only 40 pin 80 wire Ultra ATA cable can give hard disk UDMA 133 performance Also we suggest not to connect a fast hard drive with a slower IDE EIDE device
9. s F6 to specify and add the driver Press S select Other then press Enter Insert the driver diskette and press Enter Select Sil 0680 ATA 133 Controller for NT 4 0 and press Enter Press Enter to continue and follow on screen instructions to complete Windows NT 4 0 installation 2 3 6 Installation with existing Windows NT4 0 l 4 5 After installing the board boot up Windows NT Select My Computer Control Panel SCSI Adapters then click on the Drivers tab Select Add then Have Disk Insert the driver diskette into the floppy driver and type in A then click OK Highlight Silicon Image Sil 0680 ATA 133 Controller and click OK Remove the driver diskette and select Yes to restart the computer Verify Proper Installation for Windows NT4 0 l 2 Go to My Computer Control Panel SCSI Adapters Highlight Silicon Image Sil0680 ATA 133 Controller from the SCSI Adapter listing and select Properties Amessage This device is working properly is displayed in the dialog box the driver has been correctly installed 2 3 7 Installation with new Windows 2000 l Install the board and follow Microsoft procedures to install Windows 2000 accordingly At the Windows 2000 Setup screen press F6 to install the driver Insert the driver diskette Press S then press Enter Select Sil 0680 ATA 133 Controller for Windows 2000 XP and press Enter Press Enter to continue and fol
10. such as CD ROM or tape backup drive on the same channel 1 If you plan to install two hard disk drives on the PRIMARY IDE channel make sure you configured the drives as a Master and Slave according to the manufacture instructions The same rule must be followed for connecting hard disk drives to the SECONDARY IDE channel 2 Attach one end of the Ultra ATA cable that was included with this adapter to the PRIMARY IDE connector on the board Make sure pin 1 on the cable indicated by the colored stripe matches pin 1 on the PRIMARY IDE connector Figure 2 3 Connecting the Cable to On Board Connector 6 3 Attach the other end of the Ultra ATA cable to the connector of a drive Note that the ribbon cable has two connectors If you have one hard disk drive connect the end connector to the drive drive C If you have two drives the middle connector attaches to drive D Make certain that pin on the cable indicated by the colored stripe matches pin on the hard disk drive s connector when making the connections End Connector Middle Connector Internal Internal Drive 1 Drive 2 Secondary IDE Primary IDE Drive C Drive D Figure 2 4 Connecting Internal Drives 4 The same procedure applies when making connection to SECONDARY IDE 5 After making all your internal connections replace the computer s cover and screws Then reconnect the power cord and cables to the back of the computer 6 You are now ready to insta
Download Pdf Manuals
Related Search