existing revised bill remarks 1. Extent of Application
Contents
1. existing revised bill remarks prace orie TOOT OF TEET Comparison Table of New and Old Standards for Scooter 2 Type Omitted 4 Type Same as existing 3 Safety Requirements 5 Safety Requirements 3 1 Outer Appearances 5 1 Outer Appearances Modification 3 1 1 3 1 2 Omitted Same as the existing bill of Words 3 1 3 On the plate there should be no projecting objects which can cause foot injuries 3 1 4 3 1 5 Omitted 3 2 Structures 5 2 Structures 3 2 1 Handlebar should not exceed the lt Deleted gt vertical line of the ground contact point of the front wheel and its skew when pulled with the power of 300N back and forth for 10 seconds should be less than 10mm 3 2 2 Handlebar should not break away lt Deleted gt KS G 5755 when pulled with the power of 300N incorporated vertically 3 2 8 Grip should be covered with 5 2 1 Grip should be covered with coating materials such as Urethane coating materials such as Urethane sponge etc and should not break sponge etc away when pulled with the power of 10N 3 2 4 3 2 7 Omitted 5 2 2 5 2 5 Same as the existing bill 3 3 Performances 5 3 Performances KS G 5755 3 3 1 weight proof lt Deleted gt incorporated There should be no skews on foot plate wheels and folding parts when tested according to 4 2 lt Newly established gt 5 3 1 Handle Test KS G 5755 When tested according to 6 3 there incorporate2. skewed flat surface 6 12 1 2 Place a weight of 50kg at the centre of the foot plate in the vertical direction from the horizontal surface 6 12 1 3 On the lever adjusted for used in the way that manufacturer recommends or if there is no such recommended place at the position of 25mm from the end of the hand brake apply the force of 67 N to the hand brake direction from the handle grip part Note in this the force of 67 N is lever in the vertical based on the grip power of a 5 year old child 6 12 1 4 Observe and take note of any change that may occur 6 12 2 Foot Brake Test 6 12 2 1 Place scooter on a 10 skewed flat surface 6 12 2 2 Place a weight of 14kg at the KS G 5755 incorporated hand brake to the hand brake lever in the vertical direction from the handle grip part Then measure the force of the turning direction wheels contact direction with forwarding and Measurement method is same as 4 12 1 but the weights differ as 6 8 9kg centre of the foot plate in the vertical direction from the horizontal surface 6 12 2 3 Apply a static weight of 80 N to the foot brake 6 12 2 4 Observe and take note of any change that may occur 6 12 2 5 Place a weight of 70kg on the foot plate and a weight of 40kg on the foot brake and repeat 6 12 2 1 6 12 2 4 existing revised bill remarks 5 Test method Omitted 7 Test Method Same as the The existing bill warnings 6 Ind
3. GE ELA 79 YT WAAAY ASTM F 963 Standard Consumer Safety Specification on Toy Safety lt 4 gt ASTM F 963 Standard Consumer Safety Specification on Toy Safety ANSI Z356 1 American National Standard for Art and Craft Materials Crayons ASTM D 4236 Standard Practice for Labeling Art Materials for Chronic Health Hazards 1 ag m8 2h 5 HALTA eb a 5 HAALTAR AAA dE 5 1 AIEA sg 24 EPA TA ou 424 H 34 ZZ Codex FEMA Flavor and Extract Manufacturer s Associations IOFI International Organization of the Flavour Industry 4 4 9 JF FEEN sege Aes AAAA alga oJejor sr A s it aga de stach 639 ABW 3 3 LDs9el 2 000 mg kg olZololot su 5 4 gis ga Y 1 NMA xam 9 ga7 7 u 192183249 s SH gs ges erem 6 4 4 NAAS ul n T ALSS SS A 43 Ta n Hu A 8 4 6 1 FAAS 48 6 1 1 6 1 4 A MA H 6 3 4785578 Acute toxicity test 6 3 1 AGE D 3H SPF SDA 9 SD rat VER APA T8 tra 473 ZA uw cs de esp TAE e 17531 pul 1714 S E Yao 14d GRE A ol ra D AF FIA AFAA Y FE PA 110358 YA 951589 57 3 O HE 60 FECHA ac ai Sol Wb EN Ae AH AY SES ASS FEAR Z Te Y a ol 49 SASS i RBIS sb NAA ES ARMADA vp Zu TAG SATS JRI 6 3 2 YY O ASS ebd ee 59 lt A a uu eun 7 ol AE Bt FA Oral Y FA Sp AFA 7 13 Soa Ch Xo Ma Y FAR Ata Ed 018 3194 YA BaF FG zh FIRE ALE
4. existing revised bill remarks 1 Extent of Application This standard applies to a scooter which is a riding instrument with two wheels But this standard excludes those with non bearing attached wheels or those run by fuelled motor 1 Extent of Application This standard defines safety test methods and But this requirements detail indications etc standard excludes those with non bearing attached wheels or those run by fuelled motor Modification of Words lt Newly established gt 2 Related Specifications The specifications shown below comprise some parts of regulations of this standard These quoted specifications this standard as quoted in should be latest version KS A 0006 Normal testing place KS M ISO 868 Plastic and ebonite conditions of measurement of Shore hardness by durometer KS M 3824 Test polyurethane thermoplastic elastomer KS D 9502 Testing method of method of Salt water spray Statement of related standards Newly established 3 Definition Major terms used in this standard are as follows 3 1 Scooter A moving instrument which can be moved by the force of kicking with one foot against the ground while one foot on the board This is composed of more than 2 wheels one board on which one can place one foot or feet and a handle for steering This is also called scooter 3 2 Foot Plate Statement of definition
5. 5755 the surface of test piece the needle with the surface of test piece the incorporated pressured by the spring in the hole at the centre of the pressure applying surface shows the distance rebounded by the rubber surface in graduations needle pressured by the spring in the hole at the centre of the pressure applying surface shows the distance rebounded by the rubber surface in graduations al Pressure applying surface is a flat and even surface which is vertical to the pressing needle having a hole which can accommodate and slide the needle as shown in Figure 3 Its diameter should be above 10mm b Material of the pressing needle should have anti wear and anti corrosion properties and its appearance and size are as shown in Figure 3 The needle should be attached properly at the centre of the hole in the pressure applying surface When graduation shows 0 the tip of the 2 49 2 54mm above the pressure needle should protrude applying surface and when graduation shows 100 the tip of the needle should be placed in line with the pressure applying surface c The tolerance of Figure 4 which serves as a guide line for the relationship between graduation the movement of the pressing needle and the force of the spring is 8g d Graduation should be evenly marked from 0 to 100 4 4 2 3 Test Method Omitted 6 6 2 3 Test Method Same as the existing bill 4 5 4 6 Omitted 6 7 6 8 S
6. TE 5 kg JIE x Sei FHSS AVES FAA A eS ALE 9 10m1 kg93 Y 3355423 SUS 023 419 ojus diia Age dk AL Fo BAUL 12A AL u EAS Aa FEO use ia 14974 919 1398 ewe p As 33358 2348 da L Uu ATTE 4E FAA Bers Gh Ab D AG 3 BE 59 dsp Fog an 9 714 A Neg ap 1431e 3 a Aes 3 97 RAR X HL AOR MA 99 Sl ANDAR NS 24 6 4 Je SS AE O 2382 SE mss Y Peet 7 3 ERES 19 1 BAS AN Y 2 Addo YAS 75H ga we e e uu ul 245 Eel HAE s els Aro 243 97 WA xe Sol US e Shee MADE AIS 1440 5 0 10 2 9710173872 Ao ebd 9 del deret E HQ E E rie 25 0 add A T gt r VE oZ 27 mm 7T RAPPA TAPA 7 1 AAZES 738 7 1 AE FA 3x AAZES 2198934 alaz cU Aus TEA ea aj 1e AAA Aol tat Y NAME Y dat cS A Y3 29 F4 RH AT SEA YA AS Y FSAA A 4 18042 JEJL x EE Uwe ds HA ES Ad Wo sues We Aem HE Ato dere dare 7 2 7 3 AJJ 22 a AA W 8 A APA 8 EA AY 8 1 8 2 A 8 1 8 2 AAJ 22 8 3 31 HlY4 lt mue ste ARS FLIA USS 36703 nus eje AE FT ae E Y Hale 41 uae BA dad Y E WYO yao sr e Je p gt of D mM E re E or om
7. ame as the existing bill existing revised bill remarks 4 7 Impact Strength 6 9 Impact Test KS G 5755 Place a weight of 100kg on foot plate 6 9 1 Put the maximum weight set by incorporated crash it into a 50mm high hard sill 3 times at 2m sec manufacturer or if there is no such set weight a weight of 90kg on the centre of foot plate 6 9 2 Crash it into a 15cm high hard sill at 2m sec 6 9 3 Repeat above 6 9 2 three times 4 8 Drop Strength Place a weight of 500kg on the upper surface of foot plate then drop the scooter from a 30cm height onto a concrete surface 3 times 6 10 Drop Test 6 10 1 Put the maximum weight set by the manufacturer or if there is no such set weight a weight of 90kg on the centre of the foot plate 6 10 2 At a height of 15cm from the floor drop the scooter with one wheel landed Then drop the scooter with the other wheel landed at a height of 30cm 6 10 3 Repeat above 6 10 2 three times 6 10 4 With the other wheel repeat the above 6 10 2 and 6 10 3 4 9 Grip Retention Strength Activate joint parts like pin etc 10 times successively the pull the grip apart with the force of 10N by using the spring gauge etc when there is a possibility of twisted separation then twist and pull the grip for test purposes Deleted 4 10 Safety of Folding Parts Release locking lever and place handle at the furthest position and place a weight of 25kg a
8. d should be no deformation separation visible cracks or faults 5 3 2 Foot Plate Test When tested according to 6 4 there should be no deformation separation visible cracks or faults 3 3 2 3 3 8 Omitted 5 3 3 5 3 9 Same as the existing KS G 5755 3 3 9 Grip Retention Strength bill incorporated When tested according to 4 9 grip lt Deleted gt should not break away existing revised bill remarks 3 3 10 Stability of Folding Parts 5 3 10 Stability of Folding Parts When tested according to 4 10 they When tested according to 6 11 there should not be folded should be no abnormalities in use such as folding etc 3 3 11 Handle Skew Strength When tested according to 4 11 there should be no abnormalities such as lt Specified in 5 3 1 gt skews 3 3 12 Braking Power 5 3 11 Braking Power KS G 5755 When tested according to 4 12 1 if the When tested according to 6 12 there incorporated weight increases to 12 15 18kg the braking power should increase accordingly and the braking power at weight of less than 15kg should be between 40N and 120N 3 3 12 2 Hand Brake When tested according to 4 12 2 if the weight increases to 6 8 9kg the braking power should increase accordingly and the braking power at weight of less than 8kg should be between 30N and 80N should be no movement longer than 7mm 4 Test Method Newly established 6 Test Method 6 1 General C
9. der and other persons 5 Children under 8 years should be supervised by an adult when they ride Scooter 6 Do not ride scooter on wet or uneven surfaces 6 3 User s Manual Be information in easy to understand way 6 3 4 Be Conditions before riding sure to show the following sure to check Safety 6 3 2 Do not attempt unsafe skills like jumps etc 6 3 3 Do not perform arbitrary or illegal rebuilding 8 4 User s Manual Same as the existing bill 8 4 1 8 4 3 bill Same as the existing 8 4 4 Be sure to wear safety 6 3 4 Other necessary items Non use protection gears Helmet Knee and in unsafe places compliance with Elbow Protector Wrist Protector etc traffic laws when riding scooter 8 4 5 Same as the existing bill O asaya Ate Qk ES NA 9 1 48305 39 1 4 885 AJA d 2 HATA eb KS A 0006 192229 x KS A 0011 Saa Ao z KS A 3251 1 ade AAA a JA d m AJAA SAA 7 KS M 0001 sei Y AY vu e A 53 KS M0016 449 AAA xw KS M 7602 15 43914 8 KS M ISO 6353 2 359442 ot 23 wA Ag ed Als 2 UNA KS A 0006 KS A 0011 NAZAJ BEE Saal No E KS A 3251 1 AI Xp al AY di were SAA Je KS M0001 3824 Y AS un o et 53 KS M0016 24 49 W Sa KS M 7602 7 3 8 324 2 KS M ISO 6353 2 3394432 A Ala wA Avg Hee ole AS 144712 o do 8 47441379 A ebd ez KS ISO 13301 584 IJE 4 AAA 3 AFOAIS Sei BA uo zi Fr BSS ae x AFT HABA E
10. e and front wheel so that they will not swing right or left 4 3 Weight proof Test Place weight of 210kg 20cm x 20cm vertical to the centre of the upper surface of the foot plate for 10 minutes 6 3 2 2 Put 7Nm torque at both ends of grip vertically 45 upward rearward and then downward forward 6 3 2 3 Repeat 5 000 cycles of above 6 3 2 2 work while keeping 1 cycle from exceeding 1 second 6 3 3 Grip Handle Retention Test Place the weight of 70N on the grip in the axial direction of the handlebar incrementally for 5 seconds 10 seconds Deleted existing revised bill remarks Newly established 4 3 Driving Test For forward driving drive with 700N weight at 10km h speed For reverse driving drive 2km with 700N 10km h 4 4 Wheel Hardness 4 4 1 Polyurethane Materials 4 4 1 1 Test Piece Thickness of test piece shall be thicker than 6mm so that it will not be affected 6 4 Foot plate Test Place a 15cm x 15cm wooden block on the point on the upper surface which is equidistant between front wheel and rear wheel Place a weight 3 times heavier than the maximum the manufacturer or if no such maximum acceptable weight set by weight specified a static weight of 270kg 6 5 Driving Test Drive 15km at 10km h speed while placing 700N weight at the centre of gravity of the foot plate 6 6 Wheel Hardness 6 6 1 Polyurethane Materials 6 6 1 1 Test Pi
11. ece Same as the existing bill KS G 5755 incorporated by other materials If any test piece is not thicker than 6mm fold it to make it thicker than 6mm The measured surface of the test piece should be flat and even having a sufficient space to accommodate the pressure applying surface of test equipment 4 4 1 2 Test Equipment type equipment type A as test equipment In Use spring hardness test case the hardness measured by this test equipment is above 95 then use durometer specified in KS M 3043 Test method for measuring plastic hardness by durometer 4 4 1 3 4 4 1 5 Omitted 4 4 2 Rubber Material 4 4 2 1 Test Piece 6 6 1 2 Test Equipment spring type equipment type A as test equipment Use hardness test In case the hardness measured by this test equipment is above 90 then use Type D durometer specified in KS M ISO 868 6 6 1 3 existing bill 6 6 2 Rubber Material 4 4 2 1 Test Piece 6 6 1 5 Same as the Omitted Same as the existing bill existing revised bill remarks 4 4 2 2 Test Equipment 6 6 2 2 Test Equipment Use spring type hardness test Use spring type hardness test equipment Shore hardness test equipment Shore hardness test equipment as shown in Figure 2 equipment as shown in Figure 2 When the pressure applying surface of When the pressure applying surface this test equipment is in contact with of this test equipment is in contact KS G
12. ication Details 6 1 Indication Omitted 8 Indication Details 8 1 existing bill Indication Same as the 6 2 Cautions Regarding Use Be sure to indicate the following on the product or minimum package unit 6 2 1 Be sure to wear safety protection gears Helmet Knee and Elbow Protector Wrist Protector etc when riding scooter 6 2 2 Do not ride scooter on slippery surfaces or when it is raining and or snowing 6 2 3 Do not driveway places with busy traffic or ride scooter on the other unsafe places 6 10 Cautions Regarding Use 6 10 1 Be sure to indicate the following on the product or minimum package unit in a way that such indication will not be easily erased and will be easily understood by consumers 8 2 1 Warning Be sure to place below pictogram which shows the meaning of Warning Be sure to wear safety protection gears when riding scooter On each product in a way that such pictogram will not be easily erased and cautions are intensified 8 2 2 Cautions 1 Be sure to wear safety protection gears Helmet Knee and Elbow Protector Wrist Protector etc when riding scooter 2 Do not ride scooter on slippery surfaces or when it is raining and or snowing 3 Do not the driveway places with busy traffic or ride scooter on other unsafe places 4 Do not ride scooter on paved roads or driveways where there are possibilities of accidents for the ri
13. ondition of Tests 6 1 1 Temperature and Humidity Conditions of Test Locations should be with the temperature 20 15 C and humidity 65 20 C as specified in KS A 0006 Tests performed in conditions 6 1 2 Test Object KS G 5755 If not otherwise specified test object incorporated should be a project fully assembled according to manufacturers user manual 6 1 3 Tolerance If not otherwise specified tolerance of power and speed should be 5 that of mass 0 5 and that of size 0 5mm existing revised bill remarks 4 1 Outer Appearances and Structure 6 2 Outer Appearances and Structure Can be checked by the naked eye and Can be checked by the naked eye or by touch For size measurement use a can be felt by hand Alternatively can Vernir Caliper For force measurement be checked with some manipulations use push pull gauge etc of the product 4 11 Handle Skew Strength 6 3 Handle Test Place handle at its furthest position and 6 3 1 Handle Handlebar Compression place a weight of 30 kg at the centre of Test the handle in the forwards direction of 6 3 1 1 Fix handle at its furthest KS G 5755 the scooter as shown in Figure 5 for 5 position according to manufacturer s incorporated minutes user manual 6 3 1 2 Place a static weight of 45kg on the upper centre of the handlebar incrementally for 5 seconds 10 seconds 6 3 2 Handle Handlebar Fatigue Test 6 3 2 1 Fix foot plat
14. t the most easily folding point of the upper part of handle for 5 minutes 6 11 Safety Test of Folding Parts 6 11 1 Stretch scooter to use position as specified in user manual 6 11 2 Put together scooter for use in the way recommended by manufacture so that the normal folding function should not be hindered releasing locking lever for folding parts existing revised bill remarks 6 11 3 Place a weight of 880 N at the position related normal folding function in the direction of folding according to manufacturer s manual Incrementally apply the weight within 5 seconds and keep the weight for 10 seconds 6 11 4 Repeat the above 6 11 3 five times within 2 minutes 6 11 5 Fold scooter according to manufacturer s manual And repeat 6 11 1 6 11 3 one more time 4 12 Braking Power 4 12 1 Foot Brake Place a weight of 12kg 15kg and 18kg onto scooter and foot brake respectively and measure the force of the wheel s contact direction with the forwarding and turning direction as shown in Figure 6 The measurement method is to set the maximum force for wheels to move and turn 45 and regard the average of the 3 times measured values per each weight as the test result 4 12 2 Hand Brake As shown in Figure 7 fix scooter in reverse and apply the weight from the position of 25mm from the end of the 6 12 Brake Test 6 12 1 Hand Brake Test 6 12 1 1 Place scooter on a 10
Download Pdf Manuals
Related Search