THRUST E_說明書_簡
Contents
1. Pair THRUST E with a ANT compatible console Install THRUST E pedals on your bike Install cleats to the shoes Ride Tools Needed 1 8mm allen wrench for pedal installation and battery cap placement 2 4mm allen wrench for cleat installation 3 3mm allen wrench for tension adjustment 4 Grease Grease 3mm 4mm 8mm ANT LED Identification Light Stress Gauge Tension Indicator Transmitter Battery Positive Sensor A THRUST E ANATOMY Calibration Button Device ID number Battery Negative Sensor A PRE INSTALLATION Battery Information The THRUST E comes with three rechargeable 3 6V batteries one spare These batteries must be fully charged prior to installation A USB battery charger is included and it will take approximately 6 hours to fully charge the two batteries for the first time After initial full charge it will only take around 2 hours for a full charge cycle Under normal riding conditions a full charge will operate for approximately 150 hours ia gS Red LED indicates it is charging Green LED indicates the charge is complete Notes e Asingle battery can be recharged up to 500 times e If the THRUST E had not been used for more than 3 month please do charge the batteries again before riding AN Use only the battery specified for this device Failure to do so may result in malfunction and damage to the pedals and even fire Risk of explosion if battery2. is replaced by an incorrect type AN Dispose of used batteries according to local recycling policy Caution Battery Warning Failure to comply with these guidelines the lithium ion battery life may be shortened or cause damage to the charger fire chemical burn electrolyte leakage and or risk of injury may occur Do not place the charger close to a heat source such as a vehicle parked under direct sunlight To prevent damage to the device the device need be removed from the car to avoid direct sunlight Do not use a sharp object to remove the battery Do not incinerate either batteries or devices Do not place the battery in an area where child could reach Do not disassemble puncture or damage the battery Use the THRUST E battery for replacement only if the THRUST E battery is being used in other ways may risk of fire or explosion PAIRING We recommend pairing the THRUST E prior to mounting them on the bicycle Before pairing the THRUST E to a console make sure you are at least 10 meters 30 feet from any other ANT device This will avoid any accidental pairing to another ANT device Steps i Remove the battery cap on the right pedal with 8mm allen wrench 2 Insert battery into the THRUST E right pedal with the side first 3 Tighten the battery cap with 8mm allen wrench Torque 2 3Nm 4 Align sensor A and sensor B and the LED light on the E logo is lit This will in
3. THRUST E OAT VENUE GB TABLE OF CONTENTS PACKAGE CONTENTS Y 02 THRUST E ANATOMY YYY YJV HJ YTYM 02 INSTALLATION OVERVIEW 7272_____1_______ _ 02 PRE INSTALLATION _ J _ 7 gt gt Y YYT RR 02 Battery Information _ 2 mSJS_sS_Ss _ 02 PAIRING _ AH SS HSH SH2Hhs4 WHYSTTHS_H _ _ 03 Pairing Quick Guide AS _ 03 INSTALLING THE PEDALS 03 INSTALLING THE CLEATS 03 CALIBRATION S 03 Cadence Calibration 03 Static Calibration 1 04 Static Calibration Quick Guide 04 RIDE 0A MAINTENANCE AND CARE 04 TROUBLESHOOTING 2w2 J JYy H HSHS L _ ____VWH_H __ 04 SPECIFICATIONS 04 AN ATTENTION e Before beginning a power based training program be sure to consult your physician e f you use a pacemaker or implanted electronic device please consult your physician before using e When using the THRUST E pedals for the first time please be sureto practice engaging and disengaging in a safe and secure environment e Please read Battery Information carefully before using THRUST E rechargeable batteries e Carefully read the manual and follow instructions to prevent accidents and possible injury Warranty Info XPEDO THRUST E is warrantied to be free from defects in ma
4. TROUBLESHOOTING THRUST E does not pair with the console e Make sure the battery is fully charged e Make sure only the right pedal has a battery for initial pairing Console shows Multiple sensors found e Make sure the left pedal does not have a battery until the right pedal is paired first e Make sure you are least 3 feet away from another ANT device Only one side is displaying power reading e Make sure both batteries are fully charged e Repeat pairing step There is no power reading e Repeat pairing step e Perform static calibration Console keeps pairing with left pedal e Make sure batteries are fully charged on both left and right pedal e Repeat pairing step right pedal first The LED light on the Battery Charger is not lit e Check that battery is placed correctly with side towards the Xpedo logo e Make sure the USB wire connection is secure in the charger SPECIFICATIONS Data Transmitting Power Cadence Balance Battery Level Pedal Body 6061 anodized aluminum Pedal Spindle CroMo Bearing 3 sealed bearings Q Factor 53 0 5mm Release Torque Between 10 18 Nm Cleats THRUST 7 Cleat System 6 float or fixed Weight 385g pr with battery Water Resistance IPX7 Note Do not submerge or pressure wash the components Operation Temperature Range From 10 to 50 Charging Temperature Range From 0 to 40 Radio Frequency Protocol 2 4GHz ANT wireless communication protocol Accura
5. cy 2 Indoor testing Hibernate Mode 4 minutes of pedal inactivity Battery Specification 3 7V 570mA rechargeable battery Battery Charger Specification Input 5V 1A Output 4 2V 500mA Federal Communications Commission FCC Statement 15 21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user s authority to operate the equipment 15 105 b This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or a
6. dicate the battery installation was successful 5 Turn on ANT compatible console and refer to the console s manual to add a Power device 6 Verify the pairing is complete by making sure the device ID number on the console matches with the number on the THRUST E right pedal 7 Repeat the step 1 to 3 to insert battery into THRUST E left pedal INSTALLING THE PEDALS i Apply a thin layer of grease on the spindle threads Install the right pedal to the right crank and left pedal to the left crank The right pedal will have a R on the underside of the pedal body and the left pedal will have a L on the underside of the pedal body If the crank arms are recessed make sure to use 1mm pedal washers 2 Tighten the pedals using a 8mm wrench Recommended torque 35Nm or 25 ft lbs Note The left pedal spindle is a reverse thread counter clockwise to tighten INSTALLING THE CLEATS 1 Apply a thin layer of grease on the bolt threads 2 Place cleat on shoe with the washers and bolts 3 Position the cleat in desired location and tighten the bolts using a 4mm allen wrench Recommended torque 5Nm or 45 in lbs Note Red cleat is 6 float and black cleat is fixed no float CALIBRATION e Cadence Calibration Steps 1 Position the right crank arm at 12 o clock position We recommend using a trainer 2 On the right pedal rotate the ring with Sensor A so it ali
7. gns with Sensor B Figure The ANT LED will light up when the A B sensors are aligned 3 Position the left crank arm to 12 o clock position and repeat step 2 CALIBRATION e Static Calibration Steps i Clip the shoes into the pedals without your feet in the shoes 2 Rotate the pedals with the shoes 2 times to activate the pedal Do not move the crank arm 3 Place the right crank arm at 3 o clock position 4 Perform the calibration by going to the Calibrate function on your console The calibration function will vary by manufacturer Please refer to the console s instruction manual 5 Once the calibration is complete console will display a message Calibra tion Complete Note Make sure nothing is touching the pedals and shoes at this position during calibration Repeat Static Calibration every time when new cleats are installed and or the tension is adjusted Clip into pedals and start pedaling Console will display the power watts cadence and left right balance Different consoles will display the data differently on the screen Please refer to the console user manual to properly display this data MAINTENANCE AND CARE e Wipe down the contact plate on the pedal Do no use harsh chemicals or pressure washer to clean pedals e Periodically check the battery compartment for any moisture or corrosion e Power pedals will turn off after 4 minutes of no activity
8. n experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation of the device FCC RF Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment End users must follow the specific operating instructions for satisfying RF exposure compliance This transmitter must not be co located or operating in conjunction with any other antenna or transmitter
9. terials or workmanship for one year from the date of purchase Within this period XPEDO will at its discretion repair or replace any components that fail This product is ANT certified and complies with the in normal use Repairs or replacement will be made at no charge to the customer for parts or labor Customer bicycle power ANT Device Profile For a complete shall be responsible for any necessary shipping costs to warranty center This warranty does not apply to i as oe j ne cosmetic damage such asscratches and nicks ii damage caused by improper installation by an unauthorized listing of ANT Certified Products and their specific dealer iii damagecaused by a crash accident abuse misuse fire or other external causes iv damage interoperability please visit www thisisant com caused by service performed by anyone who is not an authorized XPEDO dealer or v damage to a product that has been modified or altered without the written permission of XPEDO Additionally XPEDO reserves the right to refusewarranty claims against products or services that it deems fraudulent 01 PACKAGE CONTENTS THRUST E Pedals Right pedal x 1 Left pedal x 1 3 6v 600mA Rechargeable Batteries x 3 Battery Charger with USB Connector x 1 Cleats THRUST 7 6 red x 2 THRUST 7 Fixed black x 2 Cleat Hardware 11mm cleat bolts x 6 13mm cleat bolts x 6 Cleat washer x 12 INSTALLATION OVERVIEW Pre Installation charging batteries
Download Pdf Manuals
Related Search