Kz533USB3.o Keypad Security HDD Enclosure a
Contents
1. 89 GB NTFS RoR E 3 2 5 After formatting completed you can access and write to your drive as usual 3 3 Lockthe security box Step1 Make sure you stop close or eject your hard drive from the computer before you lock the security box Step2 Disconnect the USB cable from the computer or unplug the USB cable from the Security box Note After each time the drive is powered off or USB cable is disconnected the drive will lock itself up 3 4 Unlock the security box Note After each time the drive is powered off or USB cable is disconnected the drive will lock itself up You must enter the right passcode to unlock it Enter your passcode and then e 9 if passcode is 123456789 press 1234567890 Blue LED ON and Red LED will be OFF if passcode is correct If Red LED blink twice and keep ON that s mean your passcode enter is incorrect Before enter ON ON OFF OFF passcode Passcode OFF ON OFF ON entered correct Passcode enter ON OFF Blink OFF incorrect 4 Change or Reset your passcode 41 Press for 5 second until Amber light turn ON enter your old passcode and press LED _ Red Amber Blue ON After pressing ON ON OFF for 5 second When old ON ON OFF OFF passcode enter correct 4 2 After old passcode entered correctly you can now start to enter your new passcode as same as the steps list above 3 2 4 3 After the above steps you can write files or folders to the drive afte2. K2533 USB3 0 Keypad Security HDD Enclosure Setup and User Manual Cancel Enter Cancel key Press key to clear the wrong number entered Enterkey Press key to end the passcode entered 1 2 Function of the LED Light Red LED On Lock i e the drive is being locked Blue LED On Unlock i e the drive is unlocked Green LED On In operate i e device is powered after it connected to a computer through a USB cable Flash Normal i e light will flash while data is transmitting Amber LED On While it is waiting for a new passcode or repeating the 2 time passcode entry 1 3 Status of the Keypad Security HDD Enclosure Red LED blink twice Each time when the passcode entered is incorrect Blue LED blink once passcode is entered correctly continue to enter the rest of the passcode 21 Boot up and steps to setup the security box Step Boot up the box after you insert a new hard drive Step2 Setup the passcode no limit on how many number used it must be numerical i e o 9 Always enter same passcode two times when creating new passcode Step3 After passcode setup successfully initialize set petition and format the hard drive Step4 While the drive is unlocked you can read write the hard driver as a typical mobile hard drive How to 31 Boot up the security box Holding both 1 amp 3 button together for about 20 seconds while plugging in the USB cable to a computer or to a USB powered plug Release the bu
3. r format is complete or after every time you unlocked the box 5 Frequent Asked Questions 5 1 Can I access the HDD files or data if I forget the passcode NO the drive is locked and you can t access the files or data inside the HDD Make sure you write it down and keep it ina safe place after each time you created or reset the passcode 5 2 IfI forget the passcode and the HDD is locked can I still use the drive YES you must reformat the drive again for recycle and use in this case all your files or data will be erased Please be careful if you really need to reformat the drive 5 3 When the security box is damaged or malfunction can I still use my drive YES as long as you remember your passcode You can buy the same model of security box from our manufacturer You can access the drive by entering the passcode you reset with the old box 5 4 Can I access my files or data if I take out the drive unplug from the device SATA Connector and connect to a computer with same SATA connector NO The security passcode is write directly into the drive even you take it out and reconnect it to a different computer motherboard the drive still locked
4. tton after the device finish boot up until both red and green LED light is ON Note If both buttons not pressed together or wrong keys pressed red LED will stay OFF You need to disconnect the USB cable and re connect the USB to repeat the boot up procedure as above Rel Ceen Amber olue Boot in progress OFF Blink ON Boot up success ON ON 3 2 Setup the passcode 3 2 1 After boot up press s for 5 second until Amber light turn ON 3 2 2 Enter your passcode numeric number only i e o 9 not limit on how many digits and press toend e g if you want passcode 123456789 press 1234567890 se a ee e 1 ON After ON OFF Blink OFF passcode entry 3 2 3 Enter the same passcode one more time When successful blue LED started to blink now set up completed LED Red Green Amber Blue When passcode OFF ON OFF ON o ee ee ee When passcode Blink ON ON OFF Blink OFF is the same 3 2 4 Now initial petition and format your hard drive us Step1 After boot up and security passcode setup is completed oe ing your computer Se mrs MAHR BA aT ti 13 85 GE E 29 29 GB WIT 105 69 thas eu R RSR 465 74 GB RHN 29 24 GB NTE 105 9 GB NTFS 13 87 GB F RSA F RSA RSA REO Ew sow Hho aem bee amnes nn 2 BE Se LHR S O O mc SmE i ARIA HSSE Ef mrs USRS WRSE BE ms RSR HAGE Be raTa WSBT i BERRA 3 29 29 GB WTE 105
Download Pdf Manuals
Related Search