TH-0111_Toilet bowl도큐2
Contents
1. Contents in Box 1 of 2 To view installation video scan QR code with mobile device This user manual contains the products warranty Please submit to our warranty department within 15 days of purchase E Toilet bowl installation guide Contents can be found in box 1 of 2 Before installing the Onedrous chinabowl be sure to read the safety instructions A N Attention before installation A WARNING Ifthe chinabowl is cracked please wear safety gear goggles gloves when handling it AN CAUTION 1 Please install the product as described in the manuals 2 Install the Onedrous to a level floor If floor is not level the Onedrous may not flush properly 3 Do not apply excessive force to the Onedrous when installing it Such force could break the chinabowl 4 Onedrous is designed for installation in a house and to a water source that cannot freeze If the water freezes it may crack the chinabowl 5 Onedrous may clog if diapers sanitary napkins and or wipes are flushed Check water supply valve in bathroom l This product should be installed using the included t valve E General inlet valve E Screw inlet valve E For special plumbing angle valve angle valve you may need a licensed plumber r gt 2 CA G bT slot Handle en inlet valve Before Installation Toilet space requirements 1 Distance between finished wall and the center of the floor drain must be 12 305mm 2 Water supply should be ap2. Install the new wax ring on the flange drain hole If the existing flange does not fit the Onedrous NOTE ae use enclosed flange and follow the directions When using the wax ring follow the instructions above Toilet bowl installation guide uol e e Su E Toilet bowl installation guide 23 Flange components pce ll nut washer T bolt flange packing flange 5 Flange bolt Insert bolt to flange note the direction of the bolt T bolt S oN Flange Toilet bowl nut Assemble flange to toilet bowl by using nut and washer washer TT nut 9 Remove toilet bowl and place aside Tape installation template to floor and begin to affix hanger as shown in picture below 4 Flange packing flange Insert flange packing to flange CY flange packing w 6 Flange Toilet bowl Turn toilet bowl upside down Insert flange to toilet bowl 8 Insert drain hole to ensure proper fit Turn toilet bowl right side up onto its base Please handle carefully as this may require more than one person j gt drain hole 10 check the place for installation Please check the position and distance for installation with ruler Ruler 11 Install the concrete anchor Check the position for concrete anchor and drill a hole with electric drill Drill Caulk with silicone ROYAL LINE 12 Install concrete a
3. hten Make sure skin is in contact with skin sensor Specifications Specification TH 0111 Power rating 120V 60Hz 1400W Water Direct inlet Flow Type Low Tank inlet type 1 0 7 0 kgf cm 14 2psi 99 6 psi Max 700cc 150cc min Max 700cc 150cc min Water pressure adjustments 1 5 levels Wash device Warm water temperature 1 Room Temp 93 2 F 98 6 F 104 F control ion Safety device Bi metal Thermal fuse Flow sensorHeated Room Temp 93 2 F 98 6 F 104 F Heated sW Seat Safety device Thermal fuse temperature sensor in seat Prevent low temp burning Room temp 113 F 5 levels Warm Air Heater 250W Dryer Device Safety device Thermal fuse Turbo wash function O ELB x Economy mode O Deodorizer O Inlet water temperature 41 F 93 2 F recommended 54 F 93 2 F Ambient temperature 41 F 104 F recommended 54 F 93 2 F Dimensions W 415mm 16 34inch L 695mm 27 36inch H 145mm 5 71inch Weight 43 74kg 96 43 lbs China bowl 38kg 83 78lbs Bidet 5 74kg 12 66lbs Recommended water pressure is 1 0 7 0 kgf cm Information to the user This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed a
4. nchor Put the concrete anchor into hole with hammer Hole Block 14 Fix the toilet bowl Place the toilet bowl Ak a tsy Bolt Washer Cap 16 Fix the toilet bowl like below picture water supply valve Toilet bowl installation guide 5 or D O e O gt R Trouble shooting X Please be sure to check the following aspects before asking for help Trouble shooting Factors to check The water does not spray The unit is not operating Water is leaking Water pressure is weak Seat water and dryer is not warm When the nozzle doesn t come out When water is cold or warm Body unit shakes Dryer does not work Check if the water tank is filled See if the water valve is open Check if the water filter strainer is clogged Check if the power cord is connected See if the power is turned off from the main unit Make sure that the Skin sensor on the seat touches your skin when you sit on the seat Ensure plumbing is properly connected If water is leaking from the main unit disconnect and contact service personnel H Check if the water pressure is set to low See if seat temperature Is set to low See if the water temperature is set to low See if the dryer temperature is set to low Make sure skin is touching Skin sensor Adjust the temperature Tighten the bolts do not over tig
5. nd used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one more of the following measures Reorient or relocate the receiving antenna Increase the distance between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Any changes or modifications not expressly approved by the manufacturer could void the user s authority to operate the equipment and limited warranty Toilet bowl installation guide 7
6. proximately 10 250mm to the left facing the bowl trom the center line of the flange and approximately 2 1 2 60mm above the finished floor 3 Using the provided template confirm the installation dimensions of the Rough in and the mounting blocks Water Pressure Typically the standard range of working pressure is 20 to 80 psi static The Onedrous requires a minimum working water pressure of 15 psi flowing De LINE wm INCLUDED PARTS In the box labeled 1 of 2 Check to make sure you have all these parts from the package FLANGE PART 2 X NUT 2 X WASHER 2 X T BOLT 1 X PACKING 1 X FLANGE MOUNTING SKS SDS BLOCK PART 2 X LAGBOLT 2 X MOUNTING 2 X CAPS 2 X SCREWS 2 X BUSHINGS 2 X WASHERS 2 X LAGBOLTS ANCHORS BLOCKS 0 1 x WATER SUPPLY SO VIVO Ne KOLO Re DB D VALVE ee OTHERS PAPER INSTALLATION R Wrench TEMPLATE Screwd river 10 Adjustable wrench INSTALLATION eee MANUAL peas Carpenter s level Drill Pliers Tape Measure Goggles Wax ring option Silicone for caulking Installation method a Fixed angle valve 4 Remove the old wax Must use fixed angle valve and not elbow shaped handle If replacing an existing toilet with the Onedrous you may be able to use the existing flange and simply replace the old wax ring with a new wax ring If using existing flange skip to step 9 as per the below diagram Remove the old wax
Download Pdf Manuals
Related Search