Instruction Manual
Contents
1. connection to an Earth circuit Please read these instructions carefully before commencing any work This unit must be fitted by a competent and qualified electrician Install in accordance with IEE Wiring regulations and current Building Regulations To prevent electrocution switch off at mains supply before installing or maintaining this fitting Ensure other persons cannot restore the electrical supply without your knowledge This light fitting should be connected to a fused circuit If replacing an existing fitting make a careful note of the connections Specification Voltage 240V 50Hz Lamp 1 x 23W E27 Compact Fluorescent IP rating 66 Layout e Plan the desired layout of this fitting carefully ensuring the cables will reach the distance between the junction box and the light fitting Avoid locating any cables in positions that would cause a hazard Position cables and junction boxes not supplied away from areas where they may be at risk from being cut trapped or damaged The mains supply cable must have a minimum cross sectional area of 1 0mm Always use the correct type and wattage bulb Using the incorrect wattage bulb will damage the product When changing a bulb always switch off at the mains and allow the old bulb to cool down before handling Dispose of used bulbs carefully and responsibly This product is not suitable for dimming Waste electrical products should not be disposed of with h2. Fitting replacing bulbs Instruction leaflet When changing a bulb always switch off atthe mains Insert the bulb gently into the fitting Screw clockwise and allow the bulb to cool before handling into the lampholder e Always use the correct type and wattage bulb Using e Refit the shade ensureing that the seals are correctly i the incorrect wattage bulb will damage the bulb and located Fe A S B U kh e AC ballast 23W ES Energy Saver e Undo the screws holding the shade in place and set i 46402 46403 Unscrew the lamp anticlockwise to remove Used bulbs should not be disposed of with household waste Please recycle where facilities exist We recommend cleaning with a soft dry cloth Do not use solvents or abrasive cleaners as these could damage the finish Recycling advice 4 Waste electrical products should not be disposed of with household waste Please recycle where facilities XiSt Check with your Local Authority or retailer for recycling advice Safety information For your safety always switch off the supply before cleaning SAXDL Iss 1 06112012 www saxbylighting com Saxby Lighting Ltd BH23 3PE Thank you for purchasing this light fitting Please read the instructions carefully before use to ensure safe and satisfactory operation of this product Please retain these instructions for future reference Warning This product is Double Insulated and does not require
3. nsulation tape This is to ensure earth continuity throughout your property SUPPLY LIGHT FITTING N NEUTRAL BLE N SWITCHED LIVE _ BROWN L Ne S Check that e You have correctly identified the wires e The connections are tight Commissioning e Ensure that the screws and cable entry points are sealed to maintain the IP rating of the product e Refit the white cover back into position e No loose strands have been left out of the connection block e Refit the shade ensuring that the seals are correctly located e Replace fuse or circuit breaker and switch on Your light is now ready for use
4. ousehold waste Please recycle where facilities exist Check with your local authority or retailer for recycling advice e Cables must be protected using suitable conduit or plastic trunking e The products can be wall or ceiling mounted If wall mounting ensure that the lampholder is at the top facing down Installation Existing fittings must be completely removed before installation of a new product Before removing the existing fitting carefully note the position of each set of wires e Remove the shade and set aside e Undo the screws holding the white cover in place and set aside e Hold the product in place and mark the position of the holes e Ensure the wall is capable of holding the weight Wiring Having correctly identified the wiring from your existing light fitting connect to the connection block inside the product in the following way This unit is double insulated and must not be earthed If of the product or if fitting to a ceiling ensure there is a joist at the point of fixing to support the weight of the product Take care to avoid damaging any concealed wiring and pipes The correct fixings should be used for brick cavity walls or plasterboard Fix into position If wall mounting ensure that the lampholder is at the top facing down Pierce a hole in the grommet and pull the cable through there are any incoming earth cables they must be joined together and well insulated with good quality i
Download Pdf Manuals
Related Search