Capture DMX512
Contents
1. from DMX willbe addressed exactly to her DMX system needs for its activity special cables because frequency of transmit is about 12 times higher then audio frequency has with characteristic impedance 120 ohm Work with CAPTURE DMX 512 The controller is for saving programs witch you chose from controllers DMX512 into memory o Every pressing by buttons is indicated by LED or by point ona display o LED for pressing BlackOut indicates permanent BLACKOUT for the devices o Process of the notation is indicated by LED on the button Finishing of the notation is possible by repeatedly pressing WRITE by filling up of the program memory or when it is not DMX signal 5 sec After finishing of the notation LED don t lights set BlackOut The notation is possible only when BlackOut is switch off The notation starts after receiving 2 DMX packets of the controller o The program in sequence is indicated by point on a right position of display o Set AUDIO mode is indicated by point on a left position of display CAUTION The producer don t warrant functions of the device with every DMX controller in marketing RESET clearing down the device Press BlackOut and switch on the device After 4 sec display screen CC and whole memory ofthe device clear down Setting size of packet Press AUDIO WRITE and switch on the device After 4 sec display hexadecimal value big as a input packet By buttons PRG UP and PRG DOWN you adjust the value and c2. solvent and similar chemicals which could damage surface finish or some parts of device Use soft and smooth cloth for cleaning optical parts of device and its surface Never use washing powders or other cleaning agents with grinding effect Connect the device to power supply after complete drying Service Never try to repair dismantle or do some construction changes in case of any failure Always consult qualified employee or dealer Not keeping this rule you can suffer dangerous electric shock Disconnect the device from mains before replacing the lamp or dismantling the housing Not keeping this procedure you can suffer dangerous electric shock Unplug mains lead before opening the housing and cleaning internal parts of device optical system dichroic filters etc You can suffer electric shock Unpacking Unpack the device and after acclimatisation take off the protective foil Make sure that there are no damages caused by transportation Installation The device can be installed in any position without alerting its operation For mounting use bracket of device which is a mounting hole in First make sure that the structure you are going to attach the projector is secure Connection to the control signal Each function of device is addressed according to standard protocol DMX 512 1990 4 us lt means we can control this device by any other device which provides signal included in protocol DMX 512 by serial line Connection is secured
3. Capture DMX512 y e G pk USER MANUAL CAPTURE DMX512 Location Don t install the device at places with mechanical shakings and vibrations high dustiness or high temperature Not keeping these conditions can lead to shorter lifetime or its damage DON T expose the device to influence of water rain or moisture It could lead to electric shock or fire Ventilation It is necessary to ensure fans against their covering and secure the devices to have admission ofair Supply voltage Don t use any other supply voltage meant in technical specification and manufacture label Not keeping proper supply voltage could lead to damaging the device starting a fire or its wrong function Powercord Check if power cord is not mechanical damaged and if it is connected properly Check also if the socket is designed sufficiently for needed loading Otherwise there is a danger of electric shock or a fire Power cord must not be bent excessively led through sharp edges or given to mechanical stress Don t pull the supply lead out by the flex but only by the plug The device must always be connected behind the main switch Do not touch the supply lead with vet hands you are threatened by electric shock Otherimportant cautions Don t poke any objects into cooling fans and ventilator it could lead to serious electric shock or damaging the device Be careful of no water or other liquid entering Maintenance and cleaning Don t use any
4. onfirm by BlackOut Size of input packet determine way of CAPTURE regulation of notation into memory For illustration DMX controller USC 128 transmit in maximal configuration 16 scanners 8 channels 128 B packet 16x8 It means that in case of setting packet on size FF can be 00 is packed big 256 bytes and 128 bytes is idle and takes place in memory witch you can use other way Choice of some hexadecimal values hexa decimal hexa decimal 10 16 60 96 20 32 80 128 40 64 FF 255 Protection of written programs In case you want to save your data written in memory you can use program Lock The Lock is applied by following way o by button PRG DOWN and PRG UP you choice program o by pressing BlackOUT PRG DOWN PRG UP together you lock or unlock an actually program According to condition on a display is CL closed lock oP open unlock o If you want to rewrite locked programs on a display is CL and dont allow write Technical specification Supply voltage adapter 12V Fuse T 100mA5x20mm Power consumption 10VA Weight 1Kg Dimensions 205x160x45 DMX input output DMX 512 1990 4us 6 35 stereo Jack Data Data OV Your distributor
5. provided by screened double line ended by connector JACK 6 35 1 4 Functions of the device CAPTURE DMX512 It is allow to save programs from whatever DMX controller After saving programs you chosen you can them transmit to your devices Built up 8 memory places button choice for choice program 1 8 AUDIO mode of work according to coming sound impulses Black Out Potentiometer on speed setting saved program Display screened number working program 2 modes of work sound automat STRING setting program sequence DMX IN input DMX signal In condition of it is Jack connector in DMX IN function of the button Audio Write itis seton WRITE DMX OUT output DMX signal MIC microphone capturing sound signal POWER connector on adapter SPEED setting of making programs left fast right slow STRING after pressing indicates on display point to the right Programs witch are marked will chain program sequence Switch active and deactive AUDIO WRITE when connector DMX IN is busy button is for writing programs when it is not busy switch mode audio automat PRG UP PRG DOWN Buttons for going between programs BLACKOUT setting BlackOut DMX system is a digital system by which are moved all informations between individual devices through one cable system IN OUT Abstractedly youcan control by DMX signal a lot of devices The device connected to DMX signal have to be addressed and this address determine which informations
Download Pdf Manuals
Related Search