EN USER INSTRUCTIONS AND SAFETY - Nolan-USA
Contents
1. Note The Bluetooth intercom does not work while listening to an A2DP audio source or an un Mp3 player connected via cable 10 AUDIO DEVICES WITH CABLE CONNECTION N Com B1 allows connection via cable sold separately to audio sources equipped with the 3 5mm output generally used by these devices for the headsets To listen to the audio source connect the cable to the helmet using the micro USB port then start playing the audio file on the device then activate the audio peripheral device using the specific key You can turn on or off listening in the helmet by pressing the key for 2 seconds N B You cannot stay connected in intercom mode with the pillion passenger while using the audio source via cable 17 ENGLISH 11 RI DER PASSENGER INTERCOM MODE In order to use B1 in wireless intercom mode both helmets have to be equipped with a N Com Bluetooth system In order for two N Com systems to communicate with one another they have to be paired up first 11 1 Intercom affiliation 1 Make sure both N Com Bluetooth systems are turned off 2 Set both N Com Bluetooth systems in Pairing up mode by pressing on for more than 4 seconds until the LEDS start to flash quickly 3 On either one of the two helmets press on briefly 4 After a few seconds the helmets recognize each another a beep is emitted to signal the pair up was successful and intercom communication is activated 5 Turn of2. Rider Pillion Passenger intercom open even while the satellite navigator is giving instructions thus preventing the intercom mode to be turned off every time the navigator gives instructions However if you wish to activate the Conference GPS function simply turn on the intercom manually during the GPS directions by briefly pressing on Caution this function is available only if the Pillion Passenger helmet is also equipped with a N Com system provided with the same function At the end of the GPS communication the intercom with the second helmet stays open and the Conference setting is stored for future GPS communications 9 BLUETOOTH A2DP MUSIC PLAYER You can listen to high quality music by connecting B1 to a device equipped with Bluetooth A2DP Advanced Audio Distribution Profile protocol The B1 system is also equipped with Bluetooth AVRCP Audio Video Remote Control Profile protocol which allows you to stop and resume music reproduction directly from the helmet with devices equipped with AVRCP Connection to A2DP music The connection is automatic when you turn on the player system Wait a few seconds for the connection Play music Play Press the a button and keep it pressed for 2 seconds Pause function Pause WU A Al is connected and playing music press Next track Skip When the player is playing music press a for 4 about seconds Stop playing music Stop Press for 2 seconds
3. equipped with music player with Bluetooth A2DP player has already been paired up the pairing up DOES NOT have to be repeated as the A2DP protocol has already been stored in the B1 Once the Bluetooth device has been paired up connection is automatic when the system is turned on 6 1 Affiliation reset function You can remove all affiliated devices from the system memory This operation is not reversible right after resetting you will have to repeat the affiliation procedure for the cell phone or for other compatible Bluetooth devices To erase all devices previously affiliated proceed as follows e Press on and keep it pressed for more than 4 seconds until the LEDs start to flash quickly and you hear a sharp beep in the headset indicating the Pair up mode e Press a and at the same time for 4 seconds and release them when you hear a beep The N Com will emit a special acoustic signal to confirm and will then turn itself off This function can also be turned on through PC using the N Com Wizard programme 7 MOBILE PHONE FUNCTIONS os a poong Briefly press any key when you hear the incoming call signal Hanging up rejecting a phone call Voice call if Press on and keep it pressed for about 2 seconds until you equipped hear the acoustic signal Redial last number Briefly press a and at the same time Press on and keep it pressed for about 2 seconds until yo
4. waste e The proper disposal of obsolete equipment contributes to preventing possible negative consequences on people s health and on the environment e For more detailed information on the disposal of obsolete equipment contact your municipality a waste disposal service or the store where the product was purchased 2 CONTENT OF THE PACKAGI NG The N Com B1 package contains e box B1 PC connection cable Adhesive Battery holder Key and screw Microphone Velcro pads Stop 3 INSTALLATION 3 You can download the installation video from www n com it N Com Download section Fig 1 Fig 3 Fig 4 Fig 2 Remove the N Com protection plate located on the helmet shell Fig 1 and open the helmet chin guard flip up helmets Remove the right and left cheek pads from the helmet see specific instructions provided in the user manual of the helmet Remove the Noise Reducers from the two cheek pads and tear off the pre cut plastic if equipped a Fig 7 ee ZZZ e Remove the back of the comfort padding by pulling on the neck roll until it separates from the shell Fig 4 e Temporarily put the padding on the outside of the helmet Fig 5 e Remove the N Com cover from the helmet border gasket Push from the inside of the helmet to facilitate the removal Fig 6 ONLY FOR FULL FACE HELMETS e Remove the chin guard by pulling on the special red tab e
5. To recharge the B1 system connect the USB cable to a battery charger or to a powered USB port Charging occurs as follows When you connect the Bl system to the battery charger the blue LED begins to flash When the battery is fully charged the blue LED stops B1 system turned off flashing and stays on When you connect the B1 system to the battery B1 system turned on charger the red LED begins to flash When the battery is fully charged the red LED turns Off N B If the device has not been charged for a long time a few months it may not be possible to turn on the system during the first few minutes of the charging as the voltage may drop below the minimum limit 19 ENGLISH 13 SUMMARY TABLE OF CONTROLS Pressure Brief Long Brief Long Brief Long Brief Long o del _ Increase Volume Decrease Decrease Volume audio via cable intercom intercom e Pa ff TI phone call Redial last number last number Ja connection zea O C o Sr disconnection mm S pa II o S ae PI Mode enre N Ta iT e EI TAT device zm T2 Pause aa Ter Forward oe TT TAT aT system turned off Basic Functions hn 9 Q ku U Q J O O iJ U 2 fea Mp3 player Rider Passenger intercom pair up Briefly press at the same time With N Com system in Pairing up Mode 20 3 14 LIMITED WARRANTY With this LIMITED WARRANTY CERTIFICATE Nolangroup
6. guide that explains how it works after installing it on your PC press F1 to display this guide 6 PAIRING UP BLUETOOTH DEVICES In order for the B1 system to be connected to another Bluetooth device the latter needs to be first paired up with the N Com system The pairing up procedure is the same for all Bluetooth devices mobile phones MP3 Bluetooth players satellite navigators etc 1 Make sure the B1 is turned off 2 Press on and keep it pressed for more than 6 seconds until the LEDs start to flash quickly and you hear a sharp beep in the headset indicating the Pair up mode 3 On the Bluetooth device turn on the search for Bluetooth devices refer to the Instructions manual of your device for the proper pairing up procedure as it varies depending on the brand and model of the device 4 After a few seconds the device will display the name N Com Bl v X XX followed by the manufacturer s identification data 5 Select the N Com device If a password is requested enter 0000 four zeros 6 B1 will confirm the pairing up by means of a tone in the headset and the LEDs will stop flashing 7 Turn off and on both the device and the B1 to store the pairing up data Note The affiliation is stored in the helmet and in the cell phone and it is not lost when the two devices are turned off As a result it needs to be carried out only once 15 ENGLISH Note If a Bluetooth device mobile phone or GPS
7. inha li j 5350253 B N Com products are identified by means of a code that allows product traceability and identification The identification code is found underneath the bar code printed on the product packaging 22 15 WARRANTY REGI STRATI ON FORM B1 Identification code Name oo Last name Address Phone N e mail Dealer s stamp Date of purchase of purchase B1 04 03 2013 14 21 00 Printed on recycled paper ome E S R Hf
8. tab Fig 16 Fig 17 Fig 18 e Insert the connectors set in the cable stop guide located on the side of the battery holder Fig 17 and 18 Only for full face helmets e Position the battery in the right polystyrene cheek pad housing Fig 19 10 3 3 3 Installing the system on the helmet Fig 20 e Position the system inside the helmet as shown in figure 20 next to the N Com housing in the shell e Looking at the helmet from the outside slide the rear positioning tab into groove A as shown in the figure e Press in the area marked PUSH from inside the helmet until the fastening clasp B clicks Fig 21 Fig 21 e Pull out the connectors area from the helmet gasket the gasket will have to be slightly deformed to facilitate the insertion Fig 22 11 ENGLISH Fig 23 Fig 24 e Insert the microphone connector in the micro USB electronic plate e Before you place the speaker in its housing apply the Velcro pad to the polystyrene cheek pad Fig 24 e Position the loudspeaker in the special housing obtained in the polystyrene cheek pad Fig 25 Fig 25 e Replace the polystyrene cheek pad left side positioning the cable in the groove that you see in the cheek pad Fig 25 Note Make sure the cheek pad is properly positioned in its housing pushing in the lined corner underneath the ribbing on the shell Fig 26 12 3 Only for Jet helmets or
9. the Internet site www n com it 14 3 5 1 Basic functions All N Com system functions are available through the operation of three pushbuttons a on and Every time the system is given a command a special acoustic signal can be heard which varies depending on the function being requested This way all the functions can be used while wearing the helmet The type of command given to the system depends on how long the pushbutton is pressed Press on and keep it pressed for about 2 seconds until the LEDs turn on and you hear a beep in the headset Press on and keep it pressed for about 4 seconds until the LEDs turn off and you hear a beep in the headset Briefly press a to increase the volume A double tone signals the highest volume level Briefly press to decrease the volume A double tone signals the lowest volume level System ON System OFF Increase Volume Decrease Volume 5 2 N Com Wizard M N Com Wizard is the PC application that can be used to manage and configure the B1 system The programme can be downloaded from the Internet site www n com it in the Download section In order to use it a helmet equipped with B1 must be connected to the PC using the USB cable supplied with the system N Com Wizard allows you to customize your B1 specifically e Setting the system audio levels e Update the device firmware The programme includes an on line
10. warrants this Product to be free from defects in material and workmanship at the time of its original purchase by the buyer We invite you to Read the cautions pertaining to safety and proper use Read the warranty terms and conditions Keep the originals sales receipt This must be shown in case of repairs covered by warranty In these cases the product has to be taken back to the dealer where it was purchased 14 1 Warranty coverage If any defect covered by this limited warranty certificate is discovered within 2 two years from the purchase date shown on the tax receipt Nolangroup shall repair or replace the defective product through its distribution network after having verified the defect Nolangroup shall supply all the material and labor that is reasonably required to remedy the defect except in those cases where the damage is caused by one of the items listed in the following paragraph Exclusions and limitations of the Coverage 14 2 Exclusions and limitations of the coverage This warranty only covers defects in materials and manufacturing Nolangroup shall not be considered responsible for product defects that can be attributed either partially or in full to any other cause including but not limited to e Defects or damages resulting from using the Product in conditions that differ from the usual ones e Damages caused by improper use not conforming with normal operation in accordance with the product operating a
11. 7 10 AUDIO DEVI CES WITH CABLE CONNECTION nn nn 17 11 RIDER PASSENGER INTERCOM MODE aa saza aza aa au a a au ua 18 124 4 t re of ATU LaELO Fi sicrie sik ya kine atat Ka bke bika an dikan ad kai ka da d 18 11 2 intercorm TUNCUOR ys lt i set 55534453 Xx die d doi Xw ya b l Ka Wan b d e E kak ye lala dl a 18 v 2 gt a Mees dr SEK E KEN a a a a ata 19 12 1 Battery discharged signal eee 19 L2 2 Recharging the system cioaca root oaia i oar 5210250595590252 95393 apa k 19 13 SUMMARY TABLE OF CONTROLS ccccccssssnnnnsseeeeeeeeeeesseenaaas 20 14 LIME TED WARRANTY sahana ban nad hak a ak k n k n a dida a ud k n a R ala da 21 Fik Warranty COVEra CE SN N r nnn 21 14 2 Exclusions and limitations of the coverage hh 21 14 3 Validity of this limited warranty L hh l l llllkkk kk eee 21 14 4 Procedure for the forwarding of claimS h ll k kk 22 14 5 PrOGUCE IGENEINCATION as jiy koye aide ea W e ond vases dee kwe di yed Yedi ned nan 22 15 WARRANTY REGISTRATION FORM c na aa al uu a au uu u uu ua 23 3 3 1 WARNINGS AND SAFETY Read this User Manual carefully as well as the User Manuals for other N Com kits that you will be using with the N Com B1 Read the simple rules listed below Failure to comply with these rules may lead to dangerous situations Caution The product cannot be used in official or non official competitions motordromes ci
12. AW THAT CAN BE DEROGATED AT THE PARTIES WILL SPECIFICALLY NOLANGROUP DOES NOT GRANT SPECIFIC WARRANTS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IN NO CASE SHALL NOLANGROUP BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO LOST PROFITS OR COMMERCIAL DAMAGES TO THE FULL EXTENT THOSE DAMAGES CAN BE DISCLAIMED BY THE LAW NOLANGROUP RESERVES ITSELF THE RIGHT TO MODIFY AT ANY TIME AND WITHOUT ADVANCE NOTICE THE PRODUCT CHARACTERISTICS FUNCTIONS COMPATIBILITY AND SOFTWARE Some Countries do not allow the exclusion or limitation of incidental or consequential damages or the limitation of the duration of implied warranties as a result of this the previous limitations and exclusions may not be applicable to you This warranty does not have any effect on the customer s legal rights under the national jurisdiction in force or on the consumer s rights towards the dealer sanctioned by the purchase sale contract This warranty is valid throughout the European territory and it represents the only express warranty provided by Nolangroup in relation to the sale of its own products This warranty does not affect the rights to which the buyer is entitled and which are expressly provided for by Directive 1999 44 CE This warranty does not affect the consumer s rights provided for by the law and specifically by the mi provisions of Legislative Decree 2 February 2002 n 24 14 5 Product identification
13. C_n com_ 7 NOLAN COMMUNICATION SYSTEM Firmware Version 1 xx BET USER INSTRUCTIONS AND SAFETY Nolangroup Congratulations on your purchase of an N Com product N Com B1 was made using the most advanced technologies and the best materials Long running tests and thorough system development have allowed the highest audio quality to be achieved For additional information about B1 and to download high definition instructions as well as the latest Firmware version visit the website www n com it REFERENCE STANDARDS The products of the N Com line are in compliance with standards as per the table below The Bluetooth system complies with the main safety requirements and other applicable provisions of Directive 99 5 CE Directive 2002 95 CE Directive 2011 65 CE Directive 2002 96 CE Battery Directive 2006 95 2004 108 2002 95 CE 2002 96 CE charger 2009 125 CE Directive 2006 66 The Declarations of Compliance can be downloaded from the website www n com it Download section Gsutooth TO CE Bluetooth is a registered trademark property of Bluetooth SIG Inc Contents 1 WARNI NGS AND SAFETY ss asa caseta daia poa am nat aaa dr uu uu uu u uu uu u a ua 4 Tal ROaC SA TO Sise inte ki n ke ia lao n D KE KE K kl ua K i KE ked KODA KOD a 4 1 2 Switching on the system in safe environmentS L kkezU 4 13 AVEC TT SISTA GOS sii patruleaz ke nae cena w a ao u a W Sl Da
14. Remove the right and left polystyrene cheek pads by gently pulling them out of the helmet The helmet shell can be opened slightly to facilitate the removal of the cheek pad Caution In case the polystyrene cheek pad is damaged during this operation turn to your local dealer for its replacement 3 3 1 Installing the microphone JET HELMETS OR FLI P UP HELMETS y Fig 9 Fig 10 e Prepare the microphone by inserting the microphone clamp being careful to position it properly Fig 9 Note the flat part of the clamp must be facing upward when the microphone is positioned as shown in figure 11 Fig 11 e Position the microphone in its support as shown in figure 10 being careful that the fluorescent clamp is facing toward the inside of the helmet e Insert screw in the microphone clamp use the key to screw in the microphone securing screw to the shell frame Fig 14 e Take the polystyrene cheek pad left hand side and position the microphone in its housing as shown in fig 13 making sure that the fluorescent band stays facing the inside of the helmet Fig 14 ENGUSH 3 2 Connecting the battery Only for Jet helmets or flip up helmets Fig 15 Fig 16 e Hook up the battery cable Red Black to the connector located on the wiring system Fig 15 e Insert the battery in its holder first positioning the side equipped with the cables outlet keeping the cables underneath the plastic
15. WA Gra aa er 4 14 ADPEOPEatE USC yy Ea li neon h a Dua Da v D la Dak D d Dak ah Dak Ooh ee 4 To OUalitled r SOLTO say da dan de kalan de yalan n da Yalan be a adan yu dai pic iai 5 1 6 Accessories and batteries L Lh hWW llkk kk kk kk kk kk kk kk kk kk 5 tA 1S DOS preaun EREI DN PIN PN IC RTC INI OC N INOT IC CINE PIC Ti Nea 6 2 CONTENT OF THE PACKAGI ING xak kkkkkkkkkkkk kaka kk ak kax aa xal aa a aa uu u ua u uu 6 3 TINSTALLATUON sec anala kk kk kk kaka kk kk kk kaka kaka kaka a kala aa u aa uu lua u uu a 7 3 1 Installing the microphone eee kk kk kk 9 3 2 Connecting the battery sssssrsrerrsrerrsrerrsrrrrsrrrrsrrrrsrrrrsrere 10 3 3 Installing the system on the helmet cccc kk 11 4 REMOVING THE SYST E b si nici xxx xxx aa xal uu a uu uu u uu uu u uu uu u uu uu u ua u ua 14 5 SYSTEM CHARACTERI ST CS Jk kkkkkklkkkkkkkkkkkkkakakk axxx kax aa axaaa ia ua ua 14 Bere eta al sa DEM e DD gp em 15 FAN COM VIZE no DN ar r E cl ta aa ora r ed Ra ad nec rd d Ala 15 6 PAIRING UP BLUETOOTH DEVICES Xkkkkkkkkkkkkakkakaax axa axaaa aza aa au ua 15 65L1 AT ili tioli reset TUNCEON icross Ko eo Neye Men on tai DADA ont AO DON Da AO ke W N 16 7 MOBILE PHONE FUNCTI ON Sa akkkkkkkkkkkkkkkkkaka aka kak kak aa a aa aa u ua a aa ua 16 8 GPS SATELLITE NAVIGATOR FUNCTIONS ccccsssseeeeeeeeeenes 16 9 BLUETOOTH A2DP MUSIC PLAYER XXkkkkkkkkkkkkkkka ka axaaa axaaa al aa a au ua 1
16. f both N Com Bluetooth systems and turn them back on to store the pair up data 11 2 Intercom function To activate the intercom connection turn on the two N Com systems and briefly press on on one of the helmets Intercom activation With B1 turned on briefly press on Intercom deactivation With B1 turned on briefly press on 18 3 12 BATTERY Before using the N Com device for the first time recharge the battery completely for at least 10 hours To obtain best performances from the battery it is recommended to completely recharge the battery the first few times Afterwards you can recharge the battery for shorter periods Whenever possible it is best to recharge the battery completely 12 1 Battery discharged signal When turned on the system signals when the battery is running down by switching to the Reserve mode When the battery charging power falls below 1 hour of operation the buttons a and Start to flash in order to indicate that the system is in Reserve mode Three consecutive beeps also signal the reserve mode When the battery operates in Reserve the system automatically turns itself off in case no button is pressed for 30 minutes The shutting off is signaled by a series of beeps in the helmet This function makes it possible to always have a small reserve of energy to use it again in case you forget to turn off your helmet 12 2 Recharging the system
17. flip up helmets e Secure the battery holder support to the right side of the helmet lining up the holes with the pins on the shell Fig 27 Fig 27 e Before you place the speaker in its housing apply the Velcro pad to the polystyrene cheek pad right side e Position the loudspeaker in its housing obtained in the polystyrene cheek pad right side e Replace the polystyrene cheek pad right side positioning the cable in the groove you see in the cheek pad Only for full face helmets Insert the chin guard microphone side gently placing the microphone in its housing Then press down on the red tab until the chin guard is locked in place on the helmet Fig 28 Fig 29 Fig 30 e Position the comfort padding in its housing see specific instructions provided in the helmet user manual hooking the neck roll Fig 29 13 ENGLISH e Position both the comfort cheek pads in their housing see specific instructions provided in the helmet user manual making sure that all the press studs click Note Carefully check the proper final positioning of the cheek pad pulling the chinstrap toward the inside of the helmet and testing the press studs Caution Make sure that there are no cables sticking out of the helmet and that the loudspeakers are in their housing Caution Always verify the proper length of the chinstrap and adjust it as necessary once again referring to the specific helmet instructions e P
18. iding your motorcycle e In all cases obey the Traffic Regulations and remember that riding the motorcycle has absolute priority over any other maneuver 1 2 Switching on the system in safe environments e When using the N Com system comply with all limitations and instructions related to the use of cell phones e Do not turn on your cell phone or the N Com system whenever their use is forbidden or when the devices can cause interference or dangerous situations e Turn off while refueling Do not use the N Com system in filling stations Do not use the device near combustible materials or chemical products e Turn off in proximity to explosive materials 1 3 Interferences All phones and devices with wireless signal transmission are subject to interferences that may affect the performance of the device connected to them These interferences are not ascribable to a defect of the N Com system 1 4 Appropriate use Use the device only in the normal position as described in the product documentation Do not attempt to disassemble tamper with or modify any part of the N Com system 3 Caution Adjust the volume of the N Com system where provided and of the audio sources connected to it before you use the system on the road Caution Adjusting the volume to very high levels may cause damage to your hearing Caution Adjust the volume of the N Com system where provided and of the audio sources connected to it so as to avoid aud
19. io reproduction at high volumes Constant exposure to high audio volumes may damage your hearing Caution An incorrect installation of the system in the helmet may alter the aerodynamic and safety characteristics of the helmet itself thus creating dangerous conditions Install the N Com system according to the instructions provided in the product documentation In case of doubt please contact your local N Com dealer Warning Listening to other equipment should not interfere with driving the vehicle which must be the top priority at all times Carry out all operations on the electronic equipment and on the N Com system with the vehicle stopped in compliance with Traffic Regulations 1 5 Qualified personnel e Only qualified personnel can carry out technical assistance on this product In case of any malfunction always turn to your local dealer e The helmet is a safety device Tampering with it and or with the electronic system inside the helmet in addition to invalidating the product warranty can also lead to dangerous situations 1 6 Accessories and batteries e Only use the type of batteries battery chargers and accessories approved by Nolan for the specific model e The use of a battery type different from the recommended one may lead to dangerous situations and invalidate the warranty e Contact your local dealer to see about the availability of approved accessories When disconnecting the power supply cable of any accessor
20. nd maintenance instructions provided by Nolangroup e Negligence and normal wear of internal and external parts e Any damage caused by an accident e Any change or modification made to the helmet or to the N com system by the user or by third parties e Color changes or damages caused by exposure to harmful chemical products e The use of incompatible accessories that are not part of the N Com product range e Moreover the warranty does not cover product defects caused by fortuitous events modifications or adjustments causes of force majeur or damages deriving from the product coming in contact with liquids e The internal helmet components are not and cannot be waterproof Consequently any improper exposure to rain humidity food spillages or other liquids can result in damages to the N Com electronic devices damages for which Nolangroup shall not be responsible e This warranty does not include those parts subject to wear and tear such as for example the rechargeable battery and the cables used for connection between the various N Com systems or between the N Com systems and other devices e Since Nolangroup does not supply the system on which the cell phones work it shall not be responsible for the operation availability coverage services or range pertaining to the aforementioned system e Whenever the product is used in conjunction with accessories or equipment not supplied by Nolangroup Nolangroup shall not guarantee proper ope
21. osition the e box in the relevant housing First insert the front part then press down on the e box until both hooks fully click To remove the e box press the two sliding hooks at the same time until the e box comes out Warning Do not leave the helmet exposed to atmospheric agents without the e box or the protection plate provided with the helmet 4 REMOVING THE SYSTEM To remove the system from the helmet remove the earphone and the comfort cheek pads as shown in the assembly operations Then remove the polystyrene cheek pads Remove the protection plate then looking at the helmet from the outside release the connector by acting on the fastening clasp as illustrated in the figure Fig 31 After releasing the connector from the shell also remove the right part by releasing the battery holder Now remove the entire system from the helmet 5 SYSTEM CHARACTERISTICS N Com B1 allows wireless connection to a mobile phone a satellite navigator and an MP3 A2DP player using Bluetooth technology The system can also be used for wireless intercom communication between two helmets if both helmets are equipped with a N Com Bluetooth system The system can be expanded by means of a USB Multimedia Wire accessory sold separately which is used for cable connection to multimedia sources B1 can be managed updated and customised using the N Com Wizard programme which can be downloaded from the Download section of
22. product from the dealer 14 4 Procedure for the forwarding of claims To forward a claim covered by this warranty the buyer has to directly notify the dealer where the helmet was purchased with regards to the defect presenting at the same time the defective product a copy of the sales receipt and the Warranty registration form duly filled out as instructed above PRIOR TO CONTACTING THE DEALER WE RECOMMEND THAT YOU READ CAREFULLY THE USER MANUAL ENCLOSED WITH THE PRODUCT AFTER 2 TWO YEARS FROM THE DATE OF PURCHASE THIS LIMITED WARRANTY IS VOID FOR ALL EFFECTS AND PURPOSES Repairs or maintenance under warranty do not extend the period of the warranty itself Therefore in case the product or one of its components is replaced this does not initiate a new warranty period as the purchase date of the original product shall be taken into account for warranty purposes Only for repairs or replacement of electronic components in the event that Nolangroup proceeds to repairing or replacing the product said product shall enjoy a warranty period equal to the residual portion of the original warranty or ninety 90 days from the repair date the longer period being considered The repair or replacement can be carried out even with regenerated components with equivalent functions The replaced parts or components shall become property of Nolangroup THIS WARRANTY VOIDS AND REPLACES ANY OTHER WRITTEN OR VERBAL WARRANTIES PROVIDED FOR BY THE L
23. ration of the product device combination nor will it accept requests for repairs or replacements under warranty in case the product is used in such a Way Nolangroup shall not be responsible in case the product presents limited capabilities due to the operating mode of cell phones or of other accessories or equipment not supplied by Nolangroup Tampering with the internal electronic card or with other parts of the N Com system shall invalidate the warranty Moreover the defects covered by this warranty do not include all those specific and subjective situations that may come up during the active use of the helmet such as for example comfort problems while riding or aerodynamic noises Nolangroup shall not be held responsible in any case for incidental or consequential damages including without any limitation whatsoever damages to one or more persons resulting from non fulfillment of the obligations arising from this warranty as it pertains to Nolangroup products 14 3 Validity of this limited warranty This warranty is valid only if the enclosed warranty form is duly and completely filled out with the following information e Product identification code 21 ENGLISH e Name and stamp of the authorized dealer e Product purchase date e Buyer s name and address Nolangroup reserves itself the right to not carry out repairs under warranty if the aforementioned information is removed or modified after the original purchase of the
24. rcuits racing tracks and the like Caution Installation of the N Com B1 system results in a weight increase of approximately 110g which is added to the weight of the helmet and of the other accessories Warning The electronic components of the N Com system mounted inside the helmet are not waterproof Consequently make sure the inside of the helmet including the comfort padding does not get wet in order to avoid damage to the system If it does remove the N Com system and the helmet comfort padding and let it air dry Disconnect the battery connector and let it dry as well 1 1 Road safety Always obey all Traffic Regulations in force While riding the motorcycle your hands should always be engaged in actually riding the vehicle Any operation to the N Com system must be carried out with the vehicle stopped Specifically e Set your cell phone on automatic answer see the cell phone instructions to do this e If your cell phone is not equipped with this function first stop your vehicle in a safe area in compliance with Traffic Regulations and then answer the call e Do not make any calls while riding Stop your vehicle in a safe place in compliance with Traffic Regulations and then make the call e Adjust the volume so that it does not cause a disturbance or distraction while riding and at the same time allows you to distinctively hear background noises e Do not operate your cell phone or other devices connected to N Com while r
25. u hear the acoustic signal Transferring a call To transfer an ongoing call from the helmet to the mobile phone from helmet to press both a and at the same time and keep them mobile phone pressed for 4 seconds Conference call function B1 allows a conference call with Rider and Pillion Passenger When a call comes in on a mobile phone connected via Bluetooth to B1 the Rider Pillion Passenger intercom is temporarily turned off However if you wish to share the phone call with the other helmet simply turn on the intercom manually during the phone call by briefly pressing on Caution this function is available only if the Pillion Passenger helmet is also equipped with a N Com system provided with the same function 8 GPS SATELLITE NAVIGATOR FUNCTIONS B1 is compatible with the most common satellite navigators for motorcycles By connecting the N Com system to the GPS all instructions will be transferred to the helmet Every time the navigator communicates instructions the intercom via Bluetooth with the Pillion Passenger is cut off and automatically restored at the end of the communication 16 3 Note If the navigator is pre set for connection to a Bluetooth mobile phone you will be able to receive the phone call audio directly in the helmet through the GPS In this case you can answer the call directly from the navigator GPS Conference Call Function The Conference function allows you to keep the
26. y or of the battery charger always grab and pull the plug not the cable e Do not use batteries for purposes other than the prescribed ones e Never use batteries or battery chargers that turn out to be damaged e Do not short circuit the battery e Keep the battery at a temperature between O 45 C charging 20 60 C in use e Danger of fire or explosion do not throw the batteries into a fire nor expose them to high temperatures e Do not throw out batteries together with household refuse The batteries should be disposed of in compliance with local regulations e Do not wear the helmet while the battery is recharging e The helmet should never be left within the reach of unsupervised children in order to prevent damage to their health caused by access to the batteries Lithium lon593847 3 7V 800mAh Batterycharger AKOOG 0500040VU 100 240v 50 60 Hz 5V 0 4 A S TR 038 100 240V 60 50Hz 0 1A CENGUSH 1 7 Disposal Refer to this user manual and to manuals related to other parts of the N Com system in order to disassemble the system from the helmet Once the system has been disassembled dispose of it according to the following instructions Union the product is subject to separate collection at the end of its useful life European Directive 2002 96 EC e Do not dispose of these products together with undifferentiated urban K e The presence of a crossed out wheelie bin indicates that in the European i
Download Pdf Manuals
Related Search